Construction of 500 Bedded Working Women Hostel at Aasangi Gamaharia Jamshedpur Jharkhand

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge.

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer In charge

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm diameter holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor. With Chlorpyriphos EC 20% with 1% concentration

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

CONCRETE WORK

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concete of soecified grade excluding the cost of centering and shuttering - All work up tp plinth level 1:4:8 (1 cement :4 coarse sand (Zone -III) :8 graded stone aggregrate 40 mm normial size)

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

R C C WORK

Reinforced cement concrete work in walls {any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-Ill) : 3 graded stone aggregate 20 mmnominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix including pumping of concrete to site of layinh but excluding the cost of centering ,shuttering finishing and reinforcement including admixtures in recommended proportions as per IS : 9103 to accelerate rated srtting of concrete, improve workability without impaiting strenth and durability as per direction of engineer in charge (note :- Cement content considered in this item is 330 kg/cum excess/ less cement used as per design mix is payable/ recoverable seperataly ).

All works uptp plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm./28 mm / 32mm dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. /16mm/20mm/25mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Centering and shutteing including struting, propping etc and removal of form for Foundations, footings, bases for columns, etc for mass concrete

Centering and shutteing including struting, propping etc and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shutteing including struting, propping etc and removal of form for Suspended floors, roof , landings , balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Centering and shutteing including struting, propping etc and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shutteing including struting, propping etc and removal of form for Columns, Pillars, Piers, abutments, Posts and struts

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

BRICK WORK

Providing designation 75A work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.

providing designation 75 B brickwork in C M ('1 :6 ) in foundation and Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing. taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75A brickwork in CM (1:3) in superstructure with approved quality of clean coarse sand of FM 2 to 2,5 including providing 10mm thick mortar joints , cost of screening, materials, scaffolding, raking out joints to 15mm depth curing, taxes and royalty all complete as building specification and direction of E/I

Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 112 mm thick reinforced designation 100 A brick work vuith fly ash lirne brick (FLAG)confirming to lS 12894-1990 (9"x4'5"x3" ) in C.M. ( 1 . 4 ) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials,n caffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specificationand direction of E/|.

Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary

WOOD WORK

Supplying, fiiting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors windows skylights fanlights and C/W celetial window opening including wedge over all clamps complete including application of two coats of wood preservative of approved quility onthe surface buttling walls and lintels all complete as per building specification anddirection of E/I.

Supplying fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutter door and windows with black board core blended with high quality phenol formal clehydes synihetic resin both side commercial veneered of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pe building specrfication and direction of E/l.

Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Supplying, fitting and fixing 32mm , thick good quality well dressed and well seasoned wood fully paneled shutters ( frame made of sal wood and panel of sisum wood) in doors and window with 20mm, thick panels with one side plain and other side chamfered with aluminium fittings such as hinges, sliding door, bolts, tower bolts, handled or rings, hooks and eyes, cleats, sand blocks as per schedule, taxes and royalty all complete as per building specification and direction of E/I.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet (Zinc coating not less than 120 gm/sqm) suitable for mounting 120 minutes Fire Rated Glazed Door Shutters. The frame shall be filled with mineral wool Insulation having density minimum 96Kg/sqm. The frame will have a provision of G.I. anchor fastners 14 nos (5 each on vertical style & 4 on horizontal style of size M10 x 80) suitable for fixing in the opening along with factory made template for SS ball bearing hinges of size 100x89x3 mm for fixing of fire rated glazed shutter. The frame shall be finished with an approved fire resistant primer or powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- Charge. (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (paneling to be paid for separately).

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per anufacturer’s specification and direction of Engineerin- charge 9.117.1 Extruded section profile size 48x40 mm

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). 12 mm thick frameless toughened glass door

STEEL WORK

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid .in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Supplying,frtting and fixing M.S. grill made of 20x6cmm M.S. flat as per approved design and drawing, properly fabrlcated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/1

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer. Using M.S. angle 40x40x6 mm for diagonal braces

FLOORING WORK

providing and laying, Doublecharge vitrified floor tiles in different sizes (thickness to be specified by lhe manufacturer) with water absorption less than 0.08% and conforming to lS 15622/ISO 13009 of approved make in all cotours and shades, laid on 20mm thick cement mortar 1 4 (1 cement:4 coarse sand) jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of tile 600x600 mm

Providing and fixing granite 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for flooring, kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 SQM

Providing edge moulding to 18 mm thick marble/granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1 : 3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specificaton and directon and E/I.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 :: 4 (1 cement: 4 coarse sand): 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

ROOFING & WATER PROOFING WORK

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Water proofrng for Old and New Roof Slab :- Providing and laying waterprooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible,material applied with brush, roller or spray for wate proof i n g coating as per manufactlrer specificatio With following steps :-

(a)surface preparation :-Provrding and cleaning of concrete surface to remove dLrst, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from sofftt to identify seepage, leakage. On identiiication of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners and joinis such as those betr,veen the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent Before chamfering a prime coat shall be given with the sl u rry ?!gc!ylic polyrner Repai rin g su rface irreg ularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modilied repair moriar ir;cluding a coat of bonding agent of the same with ceme nt slurry rncluding all rnaterial, labour, tools complete.

(b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, llexrble cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/SqmUcoat For the fJUrpose of n'ieasurernent tite entire treated surface will be measured."

(c) :2nd Cr:ai :-T,: apply the 2nd coat of two component acrylic modified, reatiy to-use, flexible cementttious material right angle to the '1st coat over the glass fibre liad surface. 2nd coat should be applied @0.7 kgl Sqrnt/coat. For the pltrpose of measurement the entire treated surface will be rneasurecl." Alte r three days of drying the 2nd coat, therainwater ouilets to be plugged and ponding test to be done for 48 hours to rrjerrtify se epage, leal<age from soffit and if found necessary rectification lo be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectifcation to be done as per satrsfaction of E/C protected from damage before screed over it. Watqr proofing Brand:*Sika Topseal 109hi / Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2Kl MYK Aqraiin TG Product Performance - Chemical Base Part A. Acrylic copolmer, Part B Specially graded cementitious powder - Density 1.6 l.rg/l (mixcd density) at +27oC Tensile Strength - 2 lllmm2 after 28 clays (with Fibre cloth) (According to ASTM D 2370)Prillcut Bond Streric;tl-r '-2 I'J/mm2 (concrete lajlqry) (Aqgcrdlglq ISO 4624) Slant-Shear Bond Strength -4 N/mm2 (According to FIP 5.'15) Elongation at Break -35% without Fibre Cloth and 20% wilh Fibre Clot (Accordrng to ASTM D 2370)

(d) Protection of treated surface with PCC- The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1.5:3) with proper slope ( '1:120) towards tlre rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mrn gap betuieen the panel joint. lntegralwater proofing admixture conforming to lS 2645 @ of 100 ml per bag of of cement to be added in the scree d concrete(pard separately for thts ltems).-All corners shall be charrmfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface slrould be packed properly with rich concrete and the peripheral mouih to be sealed with moisture insensitive epoxy putty of Sika lndia Pvt.Ltd / IVIYK Schomberg / Dr FixiUFosroc .For the purpose ofrreasurement the entire treated surface will be measured."

(e) Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc Warranty for Five years.

Covering of treated surface wrth PCC :- Providing 50mm thick Cementn Concrete M20(1:'1.5:3) r'naintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixing cerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr

Providing and mixing Liquid lntergral water proofing compound in Conctrete or plaster as per rnanufacturer specificatioqand as per cjirection of Eng - in Charge Brand- Sika Plastocrate plus, MYK proof WP 1 0, Fosroc-Cc.rnplast X4211 C, Dr fixit Pidiproof LW+ or Equivalent

Providing and filling of 6 mm groove between 50mm PCC panels with 6 mm thick deep thermocol strip and filling the rest 25mm with polysulphide sealant (poring grade)as per drawing and technical specification and direction of E in charge (with 18 % GST ). Brand:- sika - polysulshide,fosroc- thioflex 600, dr fixit pidi seal PS (42P) ,MYK seal PS or euivalent.

Toilet/Kitchen Water proofing:

1) Surface preparation by grinding machine, cleaning , crack filling etc. complete

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

FINISHING WORK

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I.

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding , curing and taxes all complete as per building specification and direction of E/I.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

Providing two coats of snowcem of approved shade and make over old surface including washing cleaning and preparing the walls, scaffolding , curing and taxes all complete as per building specification and direction of E/I.

ALUMINIUM WORK

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540- F & ISO 11600 Upto 10 mm depth and 10 mm width

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/ structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent biMTR.allic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the periMTR.er for holding glass.

d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc.,

enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having

all the performance characteristics etc. all omplete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineerin-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in SQM. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 SQM from the certified laboratories accreditated by NABL (National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing MTR.hod for a range of testing limit 1 to 200 mVhr” 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331- 09 testing MTR.hod for a range up to 2000 ml.” 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing MTR.hod for a range upto 2000 ml” 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME- 330-10 testing MTR.hod for a range upto 50 mm”

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing MTR.hod for Qualitative test” Tests to be conducted on site 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml”

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge. (Material shall confirm to ASTM 6063)

Floor Joint of 100 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).

Wall Joint of 100 mm gap

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre- engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063).

Roof Joint of 100 mm gap

Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints. 200 mm wide.

Providing and fixing of 15 Passenger Lift/ 1020Kgs / 1.25 Speed / 4 Floors / 4 Stops / Stainless Steel skretch proof with cast iron counter weight and T section guide rail for car and counter with lift licence.Car Cabin approved design and make

Providing and fixing of 13 Passenger Lift/ 1.25 Speed / 4 Floors / 4 Stops / Stainless Steel skretch proof with cast iron counter weight and T section guide rail for car and counter with lift licence.Car Cabin approved design and make

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 19.6.2-150 mm dia

Labour for laying, fitting and fixing NP2 R.C.C. spu pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak, proof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complete as per specification and direction of E/I. 150mm dia RCC spun pipe - Upto 3.0 metre depth of invert below G.L.

Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I. 150mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling Brick bat inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality-Circular shape 560 mm internal dia

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

CARRAIGE OF MATERIALS

SAND (UPTO 10KM LEAD)

CHIPS (UPTO 22KM LEAD)

METAL ( UPTO 22 KM LEAD)

BRICKS (UPTO 8KM LEAD)

ROAD WORK

Excavation in Soil using Hydraulic Excavator and Tippers with Disposal upto 1000 metres.Excavation for road work in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and tranporting to the embankment location within all lifts and lead upto 1000 m

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.) For Grading -II Material

Dry Lean Cement Concrete Sub- base Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Cement Concrete Pavement Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with approve grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in abatching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin- Charge.

80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

Deep Boring

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes , all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 40 mm dia G.L. column pipe - do - do - all complete job as per direction of E/I.

ELECTRICAL WORK

Point wiring in PVC conduit, with modular type switch :-

Wiring for light point/ fan point / exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box etc as required. Group A

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way modular switch, modular plate, suitable GI box etc as required.

Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :-

Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub main wiring in PVC conduit :-

Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required

2x2.5 sq mm + 1x2.5 sq mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire.

2 x 10 sq.mm. + 1 x 6 sq.mm. Earth wire

4 x 10 sq.mm. + 2 x 6 sq.mm. Earth wire

4 x 16 sq.mm. + 2 x 6 sq.mm. Earth wire

S/F light plug point Modular Type Accessories :-

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections painting etc. as required. (For light plugs to be used in non residential buildings).

S/F power plug point modular Type Accessories :-

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch, connections painting etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing Ding dong sound call bell single phase, 230 volts, complete as required.

Suppling & Fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc as required Bell push

DISTRIBUTION BOARDS & MCB's

Supplying and fixing 6 Amp to 32 Amp rating 240 volts, 10 KA "C" Curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc.,as required.

6/32 amps, Single pole

40 amps DP

50/63 amps, TPN

Supplying and fixing Single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following ways, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 Way (4 + 18), Double Door Horizontal Type

8 Way (4 + 24), Double Door Horizontal Type

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way , Double door

12 way , Double door

S/F DP MCB Isolator

Supplying and fixing following Rating, Double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as Required. 40 Amps

S/F 4P MCB Isolator

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as Required. 63 Amps

S/F DP (RCCB)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as Required. 40 Amps

TELEPHONE, TELEVISION & DATA SYSTEM (socket,wiring & conduting only)

S/F MODULAR BOXES, BASE & COVER PLATE :-

Supplying and Fixing Following Size/ Modules, GI Box Alongwith Modular Base & Cover Plate for Modular Switches in Recess etc. as Required. 1 or 2 Module (78mm x 78mm x 45mm)

S/F MODULAR TYPE SWITCH / SOCKET :-

Supplying and Fixing Following Modular Switch/ Socket on The Existing Modular plate & Switch Box including connections But Excluding Modular Plate etc. as required.

Telephone Socket outlet.

TV Antenna socket outlet.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm.

Supplying and drawing following pair 0.5 mm dia FR PVC insulated copper conductor, Unarmored Telephone cable in the existing surface/recessed steel/ PVC conduit as required. 2 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

Supplying & Fixing Modular Type Computer jack RJ 45 ISI mark 1 Module on existing Mounting plate and box Complete with all accessories as required.

INTERNAL LIGHTING FIXTURES & FANS

SITC of following rating recess / surface mounted LED round / square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part -5 / section -2 or IEC :62722 withh all neccesary accessories as required.

12W LED Round Down Light

15 / 16 W LED Round Down Light

18 /20 W LED Round Down Light

Bulk Head fitting with 9/10Watt LED.

Supply of LED Mirror Light with power 8/10W rated voltage 230V 50 Hz aluminium/ PC body with rauuning life minimum 30000 Hours

S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V 50 Hz, Single Phase Supply etc. complete as required. 20/22 W LED Tube Light

SITC LED Batten light (System lumen efficacy ≥105 <120 lm/Watt) 40 watt

SITC LED Panel light 2x2 ft. (System lumen efficacy ≥105 <120 lm/Watt) 40 watt

Supply & Installation, testing and commissioning of 9-15W LED Bracket Light fitting suitable for 9-15 Watt LED Light with all accessories as required. (Havells Cat no LHFOECE1TZ1O01/ Philips model no 31425/wipro make/ similar to BAJAJ make)

Supply insttalation , testing and commisioning of following size ceiling fan 3 balde confirming to IS : 374:2019 incuding wiring thedown roads of standed lenth ( upto 30 cm ) with 1.5 sqmm PR PVC, insulated copper wire suitable for 230V 50Hz single phase supply etc. compleyte as required. 1200mm (48 Degree) BLDC 5 star rating 32W ceiling fan

Supply and fixing of step type electronic fan regulator on existing modular plate switch box including connection but excluding modular plate etc as required.

Installation, testing and commissioning of ceiling fans/bracket fan of all sizes including wiring the down rod .of standard length (up to 30 cm ) with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc as required.

SITC of 300 mm (12") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing

MAIN LT PANEL, HT PANELS & SUB DISTRIBUTION PANELS

11KV THREE PANEL BOARD

11KV THREE PANEL HT VCB (INDOOR)-ONE INCOMER, & TWO OUTGOINGS IN IP-4X ENCLOSURE

Design, Manufacture and Supply of 3 Panel, 11 kV HT VCB Switch Board with Following Accessories :

Incoming

800A, 11kV, 350MVA for 3 Sec., TP, Horizontally isolated, horizontally drawout type, motorised spring charged, closing mechanism, motor voltage 230V AC, shunt tripping & Closing coil Voltage 24V DC, Electrically Operated, Trip Free, Dust & Vermin Proof, Vacuum Circuit Breaker(VCB) With Mechanical & Electrical OFF/ON Indicators & Provided with Following - 1 No.

CT chamber with double wound single phase, cast resin CT, 15VA burden with core-1 for metering (CL-1) and core-2 for protection (CL-5P10) and of 100/5/5A ratio - 3 Nos.

IDMT relay with 3 elements for over current (50-200%) and 1 element for earth fault protection(10-40%). - 1 Set

Anti Pumping Relay - 1 Set

Master Trip Relay - 1 Set

Trip circuit supervision relay - 1 Set

Potential Transformers, 3 Phase, 3 Limb, Drawout Type, Resin Cast 11000/(Root 3)/110/(Root 3) Ratio Class 1 Accuracy, 100 VA Burden, with HV fuse on primary side and MCB / MPCB on secondary side. - 1 Set

6 Windows Annunciator with Hooter - 1 Set

1 Window for over current trip - 1 Set

1 Window for earth fault trip - 1 Set

1 Window for master trip relay - 1 Set

1 Window for Emergency Stop Push Button - 1 Set

2 Windows Spare - 1 Set

A set of breaker ON/OFF/Trip/DC control supply healthy/Trip circuit healthy/ Spring Charged VCB in test / VCB in service & R,Y,B phase indication lamps. - 1 Set

Emergency stop push button - 1 Set

Limit switches with 4 NO/ 4 NC breaker auxiliary contacts - 1 Set

Control:- T-N-C (Trip, Neutral, Close) breaker control switch with indication arrangement. - 1 Set

All control wiring with protection & test terminal block as required. - 1 Set

Strip heater with thermostat for moisture absorption. - 1 Set

Suitable for connection to 3C x 240 sq.mm. Cross linked polythelene(XLPE) 11kV cables or as called for. - 1 Set

Cable box for 3C x 240 sq.mm 11kV XLPE Al. conductor cable. - 1 Set

HT Danger Plate - 1 Set

Incoming as described above. 1 Sets

Bus Bars:

800A TP 11KV AL. Busbars With Heat Shrinkable Insulation Sleeves

Outgoings :

630A, 11kV, 350MVA for 3 Sec., TP, Horizontally Isolated, Horizontally Drawout Type, Motorised Spring Charged, Closing Mechanism, Motor Voltage 230V AC, Shunt Tripping & Closing Coil Voltage 24V DC, Electrically Operated, Trip Free, Dust & Vermin Proof, Vacuum circuit breaker(VCB) with mechanical & Electrical OFF/ON indicators & provided with following - 1 No.

CT chamber with double wound single phase, cast resin CT, 15VA burden with core-1 for metering (CL-1) and core-2 for protection (CL-5P10) and of 50/5/5A ratio. - 3 Nos.

IDMT Relay with 3 Elements for Over Current (50-200%) and 1 Element for Earth Fault Protection(10-40%) With High Set. 1 Set

Anti Pumping Relay - 1 Set

Master Trip Relay - 1 Set

Trip circuit supervision relay - 1 Set

A Set of Breaker ON/OFF/Trip/DC Control Supply Healthy /Trip Circuit Healthy/ Spring Charged VCB in Test / VCB in Service. 1 Set

Auxiliary Relays for Transformer Faults WTI, OTI and Bucholz Relay. (To be Checked With the Requirement of Transformer i.e. For ONAN or Dry Type) For Alarm & Trip. 1 Set

12 windows annunciator with hooter:

1 window for over current trip

1 window for earth fault trip

1 window for winding temperature alarm

1 window for winding temperature trip

1 window for Oil temperature alarm

1 window for Oil temperature trip

1 window for Buchloz alarm

1 window for Buchloz trip

1 window for master trip relay

1 window for emergency stop push button

2 windows spare

Emergency Stop Push Button - 1 Set

Limit Switches With 4 NO/ 4 NC Breaker Auxiliary Contacts - 1 Set

Control:- T-N-C (Trip, Neutral, Close) Breaker Control Switch With Indication Arrangement. - 1 Set

All control wiring with protection & test terminal block as required. - 1 Set

Strip heater with thermostat for moisture absorption. - 1 Set

Cable box for 3C x 240 sq.mm 11kV XLPE Al. conductor cable. - 1 Set

HT Danger Plate - 1 Set

Outgoing as described above. - 2 Set

Powerpack as Required to Be Included (220V/24V DC), 7AH Battery for Each Breaker Module.

THREE PANEL 11KV HT VCB PANEL AS DESCRIBED ABOVE

MAIN LT PANEL

NOTE:- MCCB's Wherever Specified shall have Rotary Handle.

Suppy , installation, testing, Design, manufacture, supply inspection, handling, assembling, affecting proper connections, testing and commissioning of 2mm CRCA sheet steel fabricated cubical type Main L.T. Panel floor mounting, dust & vermin proof, front operated construction, enclosure class - IP 52, with proper treatment with 9 tank process with top/bottom removable gland plates, as required, double compression type cable glands, earth bus, hinged and lockable doors to achieve dust and vermin proof complete with all inter connections small wiring by min. 2.5 sq. mm. FRLS copper wires, ckt labels etc. The panel feeders shall be suitable for terminating suitable nos. 3.5 / 4 core armoured aluminium cable as required. Panel Should Be Internal Arc tested at 50ka for .3 sec. (PTTA)

(Under no case temperature of main LT panel shall be more at any point of the panel. To avoid heating necessary exhaust fans shall have to be provided along with top louvers).

Degree of protection IP-42

The internal control wiring shall fuse less. All control wiring and metering protection shall be by MCB's.

Colour: Siemens Gray Powder Coated or as per approved shade.

INCOMER FROM 250 KVA OUTDOOR TRANSFORMER - 2 Nos each having following

1 Nos. 630 amps four pole MCCB of fault breaking capacity 50 KA (Ics=Icu) fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/test/isolated position indicator and frame earthing contact ,confiming to IS 13947-2 1993 as amended upto date complete with following Accessories.

1 set of 3 CT's of ratio 630/5A, Class 1.0 accuracy 15 VA burden for APFCR.

Independent manual spring closing mechanism - 1 No.

Microprocessor release (EMI and EMC certified) for over current, earth fault and short circuit protection - 1Set .

3Nos. Phase indicating LED lamps with 2 Amp backup MCB, breaker ON/OFF/Trip indication light with 2A MCB , test terminal block set, MCB , circuits as per standatd practice , auxiallry contact for positive interlocking of the breakers as required.

Shunt trip coil 220 Volt AC.

INCOMER FROM DG SET (250 KVA) - 2 Nos each having following only switchgear provision in LT Panel if DG Set required

1 Nos. 400 amps four pole MCCB of fault breaking capacity 50 KA (Ics=Icu) fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/test/isolated position indicator and frame earthing contact ,confiming to IS 13947-2 1993 as amended upto date complete with following Accessories.

1 set of 3 CT's of ratio 400/5A, Class 1.0

Independent manual spring closing mechanism - 1 No.

Microprocessor release (EMI and EMC certified) for over current, earth fault and short circuit protection - 1Set .

Protection releases with LSIG and Over voltage ,under voltage,Reverse power protection Relay & Metering & Accessories for each D G set incomers

3 Nos. Phase indicating LED lamps with 2 Amp backup MCB, breaker ON/OFF/Trip indication light with 2A MCB , test terminal block set, MCB , circuits as per standatd practice , auxiallry contact for positive interlocking of the breakers as required .

Shunt trip coil 220 Volt AC.

1 nos battery charger with DC voltmeter and ammeter suitable for the DG sets (250 KVA)

INTERLOCKING

Interlocking logic electrical Interlocking between incomers and bus coupler and it should have auto start and auto trip facility for Automatic Operation of The Breakers With Manual Over Rid Facility.

BUS COUPLER

One Number 630A 4 pole edo ACB as Bus Coupler with ON/OFF Indication.

BUS BAR

630A TPN Aluminium bus bar with heat Shrink Sleeve

OUTGOING

ALL THE MCCB'S SHALL BE EQUIPPED/ PROVIDED WITH ALL ACCESSORIES & IN BUILT PROTECTION RELEASES

2 Nos. 200 AMPS TP+N MCCB (Capacitor Panel 1 & 2)

1 No. 400A 50KA 4P MCCB (Spare)

1 No. 200A 50KA 4P MCCB (Spare)

1 No. 125A 50KA 4P MCCB (Spare)

Other items such as

1 set of control wiring

1 Set of designation plates

NOTE :- Adequate Quantity of Fire Suppression system with Pneumatic gas cylinder and Heat Sensitive Pneumatic tubing to be used in panel as per the current fire norms & SURGE PROTECTION DEVICES Type 1 ( Class B), 4 Mode, spar type suitable for 10/350µs surge, 3Nos. phase to earth and 1Nos. neutral to earth with impulse Current Iimp. ≥ 50KA Per mode & In ≥ 25kA per Mode.

Complete Panel as Above

FLOOR DISTRIBUTION PANELS

SITC of cubicle Panel suitable for 415V, 3 phase, 4 wire 50 HZ Ac supply system, fabricated in conmpartmentalized (preferbly) design from CRCA sheet of 2mm thick for frame work and covers, 3mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable Amp capacity extensible type TPN aluminium alloy bus bars of high conductivity, DMC/SMC bus bar supports, , bottom base channel of MS section not less than 50mm x 50mm x 5mm thick, entire pannel shall have a common copper earth bar 25mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of AI. bus bars and control wiring with 2.5 sq.mm. FRLS PVC insulated copper conducter S/C cable, cable alleys, cable gland plates in two half. i/c providing following switch gears :-

INCOMER : 125 AMP 25KA FP MCCB

BUS BAR : 160 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves.

OUT GOINGS :

14 Nos 63 AMP 4P MCB Including 1 set of Indication Lamp

3 Nos 40 AMP DP MCB Including 1 set of Indication Lamp

complete panel as above and complete

MAIN LIFT PANEL

Design, manufacture, supply, installation, testing and commissioning of Floor Mounting Panel cubicle type panel fabricated out of CRCA sheet steel , floor mounted totally enclosed switchbaord suitable for use of 415 volts , 3 phase, 50 HZ complete with aluminium bus bar and all accessories including supply and fixing of following incoming and outgoing switchgears, Panel Should Have Double Earthing Provision which connected to the nearest earth grid.

INCOMER : 200 AMP FP MCCB

BUS BAR : 250 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. The current density of bus bar shall be minimum 0.8 sq mm /amp.

The Maximum allowable temperature for the Bus bar to be restricted to 90 deg C. The temperature rise should be restricted to 45 deg C above ambient temperature.

OUT GOINGS :

2 No. 125A 25KA 4P MCCB

3 No. 100A 25KA 4P MCCB

complete panel as above and complete

LIFT PANEL 1

Design, manufacture, supply, installation, testing and commissioning of Floor Mounting Panel cubicle type panel fabricated out of CRCA sheet steel , floor mounted totally enclosed switchbaord suitable for use of 415 volts , 3 phase, 50 HZ complete with aluminium bus bar and all accessories including supply and fixing of following incoming and outgoing switchgears, Panel Should Have Double Earthing Provision which connected to the nearest earth grid.

INCOMER : 125 AMP FP MCCB

BUS BAR : 250 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. The current density of bus bar shall be minimum 0.8 sq mm /amp.

The Maximum allowable temperature for the Bus bar to be restricted to 90 deg C. The temperature rise should be restricted to 45 deg C above ambient temperature.

OUT GOINGS :

1 No 63 AMP 4P MCB Including Indication Lights (Lift 1)

1 No 63 AMP 4P MCB Including Indication Lights (Lift 2)

1 No 40 AMP DP MCB Including Indication Lights (Machine Room DB)

1 No 40 AMP DP MCB (Spare)

1 No 63 AMP 4P MCB (Spare)

complete panel as above and complete

LIFT PANEL 2 & 3 (TYPICAL)

Design, manufacture, supply, installation, testing and commissioning of Floor Mounting Panel cubicle type panel fabricated out of CRCA sheet steel , floor mounted totally enclosed switchbaord suitable for use of 415 volts , 3 phase, 50 HZ complete with aluminium bus bar and all accessories including supply and fixing of following incoming and outgoing switchgears, Panel Should Have Double Earthing Provision which connected to the nearest earth grid.

INCOMER : 100 AMP FP MCCB

BUS BAR : 125 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. The current density of bus bar shall be minimum 0.8 sq mm /amp.

The Maximum allowable temperature for the Bus bar to be restricted to 90 deg C. The temperature rise should be restricted to 45 deg C above ambient temperature.

OUT GOINGS :

1 No 63 AMP 4P MCB Including Indication Lights (Lift)

1 No 40 AMP DP MCB Including Indication Lights (Machine Room DB)

1 No 40 AMP DP MCB (Spare)

1 No 63 AMP 4P MCB (Spare)

complete panel as above and complete

complete panel as above and complete

MULTIPURPOSE HALL PANEL

SITC of cubicle LT pannel suitable for 415V, 3 phase, 4 wire 50 HZ Ac supply system, fabricated in conmpartmentalized (preferbly) design from CRCA sheet of 2mm thick for frame work and covers, 3mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable Amp capacity extensible type TPN aluminium alloy bus bars of high conductivity, DMC/SMC bus bar supports, , bottom base channel of MS section not less than 50mm x 50mm x 5mm thick, entire pannel shall have a common copper earth bar 25mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of AI. bus bars and control wiring with 2.5 sq.mm. FRLS PVC insulated copper conducter S/C cable, cable alleys, cable gland plates in two half. i/c providing following switch gears :-

INCOMER : 1 Nos 250 AMP 25KA FP MCCB

BUS BAR : 315 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves.

OUT GOINGS :

10 Nos 63 AMP 4P MCB Including 1 no. of Indication Lamp

complete panel as above and complete

COMMON SERVICES ESSENTIAL PANEL

SITC of cubicle LT pannel suitable for 415V, 3 phase, 4 wire 50 HZ Ac supply system, fabricated in conmpartmentalized (preferbly) design from CRCA sheet of 2mm thick for frame work and covers, 3mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable Amp capacity extensible type TPN aluminium alloy bus bars of high conductivity, DMC/SMC bus bar supports, , bottom base channel of MS section not less than 50mm x 50mm x 5mm thick, entire pannel shall have a common copper earth bar 25mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of AI. bus bars and control wiring with 2.5 sq.mm. FRLS PVC insulated copper conducter S/C cable, cable alleys, cable gland plates in two half. i/c providing following switch gears :-

INCOMER : 1 Nos 250 AMP 25KA FP MCCB

AMF PANEL INCOMER :- 1 from Normal Supply & 1 From DG Set O/G

BUS BAR : 315 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves.

OUT GOINGS :

1 No 125 AMP 25KA 4P MCCB Including Indication Lights

2 NO 200 AMP 25KA 4P MCCB Including Indication Lights

1 NO 250 AMP 25KA 4P MCCB Including Indication Lights

1 NO 125 AMP 25 KA 4P MCCB Including Indication Lights

3 NO 63 AMP 4P MCB Including Indication Lights

2 NO 40 AMP 4P MCB Including Indication Lights

complete panel as above and complete

EXTERNAL LIGHT FEEDER PILLAR

Design, Manufacture, Supply, Installation, Testing and Commissioning of Panel Fabricated out of 16 SWG CRCA sheet steel, IP 54, wall / floor mounting type with rain canopy The sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness. the board includes 415 /240 V electrolitic Aluminium Bus Bar, removable gland plates, cable glands, including connection with outgoing feeders complete in all respect, Panel Should Have Double Earthing Provision Which Connected to the Nearest Earth Grid.

INCOMER:

BUS BAR

TPN Aluminium bus bar with heat Shrink Sleeve rated for 125A.

OUTGOING

18 nos 20A SPN MCB

2 nos 63A 4P MCB

2 nos 40A 4P MCB

Other items such as

1 Set of control wiring

1 Set of designation plates

complete panel as above and complete

CABLES & ACCESSORIES

SUPPLY OF L.T. CABLE:

Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming to IS-7098. (Part-I).

3.5 core, 300 sq.mm.

3.5 core, 240 sq.mm.

3.5 core, 185 sq.mm.

3.5 core, 95 sq.mm.

3.5 core, 50 sq.mm.

3.5 core, 35 sq.mm.

3.5 core, 25 sq.mm.

LT CABLE LAYING

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

LT CABLE JOINTING & END TERMINATION

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required.

3½ X 25 sq. mm (28mm)

3½ X 35 sq. mm (32mm)

3½ X 50 sq. mm (35mm)

3½ X 95 sq. mm (45mm)

3½ X 185 sq. mm (57mm)

3½ X 240 sq. mm (62mm)

3½ X 300 sq. mm (70mm)

SUB STATION

Supply, installation, testing and commissioning of following capacity (continuous loading) BEE 5 Star rated (Corresponding Level as per BIS amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50 Hz, Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound transformer (Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better, suitable for out door/indoor applications with On Load Tap Changer (OLTC) 250KVA

Automatic Power Factor Correction (APFC) System

Supply, Installation, testing and commissioning of Automatic Power Factor Correction (APFC) panel, indoor type floor mounted free standing totally enclosed, extendable, IP 42, of following capacity for 3 phase, 415 V + 10 %, 50 Hz AC System for Ambient temperature -5°C to +40°C, fabricated in compartmentalized designed made of CRCA sheet steel of 2.0mm thick for framework & covers, 3 mm thick for gland plate i/c cleaning & finishing complete with 9 tank process for powder coated of approved shade ( RAL 7032-Siemens gray or as approved by Engineer-in-Charge) 100 KVAR

Supply, installation, Testing & Commissioning of 'Silent Type Diesel Generating set as per CPCB IV + or better norms along with having Prime Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, including testing at factory and site with fuel, load for test and other necessary arrangements Complete as per CPWD specifications, should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings 125KVA

Supply of H.T. Cable

Supply & Testing of following 11 KV (E) grade multicore Aluminium conductor XLPE insulated cable, insulation screening with extruded semi conducting compound in combination with copper tape armoured cores laid up, inner sheath of PVC tape, galvanised steel flat strip armoured and overall PVC sheathed cable conforming to IS: 7098 (Part - II) and complete with all latest amendments etc. complete as required. 3 C x 120 Sq. mm 11 KV (E)

H V CABLE LAYING

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV of size exceeding 120 sqmm but not exceeding 400 sq.mm direct in ground including excavation, sand cushioning protective covering and refilling the trench etc. as required.

H.T Termination: DSR ITEM

Supply and making Indoor cable end jointing with cast resin compund, including lugs and other jointing materials for following size of 3 core, XLPE aluminium conductor cable of 11KV (E) grade as required. 3 C x 120 Sq.mm (11KV E)

Supply and making Outdoor cable end jointing with cast resin compund, including lugs and other jointing materials for following size of 3 core, XLPE aluminium conductor cable of 11KV (E) grade as required. 3 C x 120 Sq.mm (11KV E)

Supply and Making Straight Through Cable Jointing With Cast Resin Compund, Including Ferrule & Other Jointing Materials for Following Size of 3 core, XLPE Aluminium conductor cable of 11KV (E) grade as required. 3 C x 120 Sq.mm (11KV E)

RISING MAIN & ACCESSORIES

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm atnominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. 400A 25kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required 200 A 15kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with rovision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 400 A 25kA SC for 1 sec

Providing and fixing following rating and breaking capacity MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes cubicle panel, making connections, etc. as required.

200 amps, 35ka fixed thermal setting

400 amps, 35ka adjustable thermal setting

EARTHING & LIGHTING CONDUCTOR

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.

Earthing with Copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.

Providing and fixing 25 mm X 5 mm GI strip in 40mm dia GI Pipe from earth electrode including connection with GI nut bolt, spring, washer, excavation and refilling etc as required

Providing and fixing 25 mm X 5 mm Copper strip in 40mm dia GI Pipe from earth electrode including connection with brass nut bolt, spring, washer, excavation and refilling etc as required

Providing and fixing 25 mm X 5 mm Copper strip on surface or in recess for connections etc. as required

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing of lighting conductor finial made of 25 mm dia 300 mm long, GI tube having single prong at top with 85 mm dia 6mm thick G.I Base plate including hole etc. as required

Providing and fixing GI Tape 20mmx 3mm thick on parapet or surface of wall for lighting conductor complete as required. ( for Horizental Run)

Providing and fixing GI Tape 20mmx 3mm thick on parapet or surface of wall for lighting conductor complete as required. ( for Vertical Run)

Providing and fixing testing Jointing made of 20mmx 3mm thick G.I Strip 125 mm Long. With 4 nos of G.I bolts. Nuts chuck nuts and spring washers etc. as required

Providing and Laying G.I tape 32mm x 6mm from earth electrode directoly in ground as required.

UPS SYSTEM

SITC - Online UPS- Input supply: Three Phase, Output supply: Three Phase, The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up 10KVA (Each Power module shall be < 10 KVA)

CABLE TRAYS

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Cable Tray Bends as per Requirement)

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

CONVENTIONAL FIRE ALARM SYSTEM

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25mm dia

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying and laying of following sizes FR PVC insulated single core copper wire in existing conduit complete as required. 2x2.5 sq mm

IP CCTV SYSTEM

Supply, installation, testing and commissioning of Cat 6, 23 AWG Bare Copper Solid Conductor U/UTP Unshielded LSZH, in accordance to ANSI/TIA 568 C.2 Category 6, Flame Rating IEC 60332-1, Halogen Acid IEC 60754 -1, Smoke Density IEC 60134-2, ISO/IEC 11801–2nd Edition, 250 Mhz Bandwidth, ASTM D 4566, 5.8 mm Nominal Diameter, HDPE Insulation with Diameter 0.95 +/- 0.05mm, No Shield/Non Metallic Barrier Tape, Breaking Strength : >= 400N, Conductor Resistance <= 8.0 Ω /100m, Min. Elongation at Break of Insulation : 400%, Min. Jacket Tensile Strength >= 10 N/mm2 (Mpa), Dielectric Strength: DC 1500 V /Min., Euroclass Eca, Propagation Velocity : 69% (nominal), RoHS Complied, Cable Roll of 305 Mtr

Supply, Installation, Testing & Commissioning of 24-Port 1U Unloaded Universal Modular Straight Patch Panel preloaded with cable support Bar (with slots to tie individual cable properly at the Support Bar), Stainless Steel Rear Metal Frame, Individual Port Transparent Shutter and Labelling, Preloaded earthing plug for surge protection, UL 1863 Complied, CRC Metal with Black Powder Coated, RoHS Compliant, Individually Replaceable Port IO, (Shuttered IO not recommended, because when shutter gets malfunctioned then entire IO is of no use).

Supply, Installation, Testing & Commissioning of Cat6 Patch Cord U/UTP Unshielded 24AWG Bare Copper, Stranded Flexible Conductor, HDPE Insulation, LSZH Jacket, ANSI/TIA 568C.2 Category 6 Patch Cord, Support 1GBASE-T with Min. 250Mhz Bandwidth, Operating Temperature -20 ℃ to + 60 ℃, Diameter <= 6.0mm Nominal, No Shield or Barrier Tape Inside, Min. 750 Plug Mating Cycles, PC UL94-V-0, Factory assembled with Transparent Premoulded Boots, Length 1 Meter. ETL/NABL Certified.

Supply, Installation, Testing & Commissioning of Cat6 Patch Cord U/UTP Unshielded 24AWG Bare Copper, Stranded Flexible Conductor, HDPE Insulation, LSZH Jacket, ANSI/TIA 568C.2 Category 6 Patch Cord, Support 1GBASE-T with Min. 250Mhz Bandwidth, Operating Temperature -20 ℃ to + 60 ℃, Diameter <= 6.0mm Nominal, No Shield or Barrier Tape Inside, Min. 750 Plug Mating Cycles, PC UL94-V-0, Factory assembled with Transparent Premoulded Boots, Length 2 Meter, ETL/NABL Certified.

Supply, Installation, Testing & Commissioning of UK Style (Square) Keystone-Type Shuttered Faceplates, 1, 2 & 4 port configurations, White Color, Elegant 2 Piece (2 Plate) design for better aesthetics , Cover and Base Plastic Material ABS-UL94-V2, 86 x 86mm

Supply, Installation, Testing & Commissioning of 22U Floor Standing Welded/CKD Steel Racks shall be designed for Networking, Servers, Data Centre’s, Audio Video, Telecom and Lab applications.Adjustable 19” equipment mounting verticals provide better mounting flexibility and maximizes the usable mounting space.100% assured compatibility with all equipment conforming to DIN 41494. General industrial standard for equipment to conforms to DIN 41494 or equivalent ISO standard.Front Door should be Lockable Toughened Glass Door, Steel Single, Steel Dual. Standard Finish should be Powder Coated with Black colour. Mounting Option : Castor wheels (Front 2 wheels with Break and rear without break) Or Levelers Or Base plinth. Static Load : 30 kgs.Standard Accessories Like Power Distribution Units, Cable Manager, Fans and Mounting hardware. Size Options : 600 x 600 mm / 600 x 800 mm / 600 x 1000 mm / 800 x 1000 mm / 800 x 1200 mm

Supply, installation, testing and commissioning of 5 MP Dome camera ,ONVIF profile S,G & T. UL , CE , FCC, BIS,Certified, OEM defined MAC address, 1/2.7” Progressive Scan CMOS ,3.6 mm fixed lens , Quad stream Each stram support H.265 compression simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 / 100,000 s , WDR , Compression : H.265/H.265+/H.264/H.264+ .SD card support upto 256GB , frame rate : Main stream should support 25/30 fps@5MP, Built in Mic, Edge analytics : Face Detection, Customer Flow staistics, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection. Queue length detection Regional population statistics, SOD-Stationaary Object Detection, Motion Detection, Tempring Detection, Rare Sound Detection, License Plate Detection. Defog. Protocols:- TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, SMTP, NTP, UPnP, SNMP, HTTPS, FTP, P2P, UDP,PPPoE, Bonjour. In built IR LED , IR Distance upto 30 meters , IP 66 , POE.

Supply, installation, testing and commissioning of 5 MP Bullet camera ,ONVIF profile S,G & T. UL , CE , FCC, BIS Certified , OEM defined MAC address, 1/2.7” Progressive Scan CMOS ,3.6 mm fixed lens , Quad stream Each stram support H.265 compression simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 / 100,000 s , WDR , Compression : H.265/H.265+/H.264/H.264+ .SD card support upto 256GB , frame rate : Main stream should support 25/30 fps@5MP, Built in Mic, Edge analytics : Customer Flow staistics, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection. Queue length detection Regional population statistics, SOD-Stationaary Object Detection, Motion Detection, Tempring Detection, Rare Sound Detection, License Plate Detection. Defog. Protocols:- TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, SMTP, NTP, UPnP, SNMP, HTTPS, FTP, P2P, UDP,PPPoE, QoS, Bonjour. In built IR LED , IR Distance upto 30 meters , IP 66 , POE.

Supply, installation, testing and commissioning of 5 MP PTZ Camera , UL,CE,FCC Certified , ONVIF profile S,G & Q , Quad stream,4.3-141.9mm focal length , 33 X Optical Zoom , 12 X digital Zoom ,Frame rate : 20 fps ,Shutter Speed : 1/5 ~ 1/100,000s , Inbuilt IR , IR distance upto 200 mtr , 2D / 3D noise reduction ,120 dB WDR , 360 deg endess pan , tilt -10 to 90 deg , auto flip support ,255 presets ,Auto pan ,Edge analytics : Pedestrian Intrusion Detection, Line cross Detection, Heat Map,Cross Count,Stationaary Object Detection, Vehicle Detection, face Detection, , SD Card supportup to 128GB , white balance-Auto/manual/indoor ,Fixed Iris, Alarm : 1 IN , 1 Out , Audio - 1 IN/1 Out,RS485,ROI,1xBNC IP 66 weather proof , Power : 24V AC/ POE+ /DC12V.

Supply, installation, testing and commissioning of 16 channel NVR , ONVIF compliant , CE,FCC, & BIS Certification, recording bandwidth 320 Mbps , output interface 1 HDMI (up to 4K), 1 VGA , Alarm in/out :16ch in / 4ch out , 1 X RJ-45 port (1000M) , Bit Rate 16kbps-20mbps per channel, Sync Playback 4/8/10/16 ch playback, iOS smartphone support , 2 HDD support , each HDD slot support upto 12 TB HDD , , 1x3.0 USB for backup /upgrade , 2x 2.0 USB for mouse, Display resolution up to 4K, 1 E-Sata Port, RS-485 Port, Cloud Storage, Net HDD, Edge analytics : Customer Flow staistics, Face Attendence, Face Detection and Recognition, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection, Queue length detection, Regional population statistics, SOD-Stationary Object Detection, Deterrence, PIR, AI Registerd Qty- 10000 & AI Captured Qty- 200000. Protocol support:- HTTP, HTTPS TCP/IP, IPv4, UPNP, RTSP,UDP,SMTP,NTP,DHCP,DNS,IP filter,PPPOE,DDNS,FTP,IP search, P2P, NFS/SMB/CIFS, IPC Management.

Supply, Installation, Testing & Commissioning of L2+ managed industrial PoE switch with 24*10/100/1000M RJ45 ports and 4*1/10G SFP+ fiber slot ports.

Supply, Installation, Testing & Commissioning of 16TB Surviellance Hard Disk.

Supply, Installation, Testing and Commissioning of Full HD 55" LED Professional Display Panel.

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest.

EXTERNAL LIGHTING

S.I.T.C of Following rating LED Post Top lamp made in die cast aluminium housing with decorative clear / opel acrylic diffuser on existing pipe including connection with 1.5sq.mm coppwr conductor etc all complete as required. 20/25W LED Post top lamp clear

S.I.T.C of Following rating approved make LED Bollard Fitting with cylindrical shape and inverted cone shape head of height 600 to 850 mm power input -8/9 watt with die cast aluminium housing opel with PC diffuser, IP-65/54 protection, confirming to IS : 10322 part 5 etc all complete as requird. (Excluding Plinth Charge.)

S.I.T.C of Following rating LED Flood Lighting Luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270V AC 50Hz. Luminarie shall be confirm to IS 10332 Part 5/section 5 and shall be complete with all necessary accessories as required. 90/100W LED Flood Light

S.I.T.C of Following rating LED Street Lighting luminare with pressure die cast housing and toughened glass cover (IP 66 protection ) in existing pole / pipe for supply voltage 100-270 AC 50Hz Luminare shall be confirm to IS :10322 part 5/ section-3 and shall be complete with all nessessary accessories as required.(Approved Make:- Havells / Philips / Crompton / Wipro). 70/72W LED Street Light

Supplying & installation of 7 mtr. Height Octagonal Hot Dip galvanized pole (BOP. 7030) with top dia 70 mm bottom dia 130 mm & made of 3 mm thick sheet base plate dimensions 200x200x12 mm (LxBxT) including suitable size of foundation bolt all complete as required (without Arm).

1M Single Arm Suitable for 70MM Top

Installation, Testing & Commissioning of the 7 mtr Octagonal Pole & Light Fitting with the help of suitable tools and plants, and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity og 10T/sqmtr but excluding wire and mcb

Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming to IS-7098. (Part-I). 2 core, 6 sq.mm.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 3½ X 25 sq. mm (28mm)

Supplying and laying of following sizes FR PVC insulated single core copper wire in existing conduit complete as required. 3x2.5 sq mm

MANHOLE & HUME PIPE

Providing and laying non pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixtures of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete

150 mm dia

250 mm dia

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

HDPE PIPES

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 200 mm dia (OD-200 mm & ID-175 mm nominal)

SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM

Supplying installation testing and commissioning of Grid interactive roof top solar photo voltaic power generation system including all the required accessories like Solar PV module, Grid Tie invertor, arrey junction box, cabling & wiring, earthing, surge protection device, FRLSame structure for mounting of solar panel. The cell shall be poly crystaline silicon cells of 6 inch each and module efficiency shall be more than 17%. Solar module shall have linear output warranty with degradation not exceeding 0.7% FRLSom 2nd Year onwards. Minimum 80% power output must be assured at end of 25 years. The FRLSont glass of solar module shall be low iron tempered glass ARC type. Termination box shall be Thermo-plastic, IP 67 or better, UV resistant with built-in-bypass. The nominal power of a single PV module shall be minimum 540 Wp or higher. Positive power tolerance modules only to be used. RF identification tag for each solar module shall be provided inside the module and must be able to withstand environmental conditions. The solar panel shall be complience of IEC 61215, IEC 61730 certified by TUV Rheinland / UL. The solar panel shall be installed as per BOQ & detailed technical specification.

PLUMBING WORKS

SANITARY INSTALLATIONS

Supplying , fitting and fixing vitreous white glazed earthen ware I.W.C of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I 'p' trap 15 liters C.I.pull and let go flushing cistren of names or other I.S.S. equivalent make , complete with all fitting , C.I.or C.C. brackets 32mm alkathene/P.V.C telescopic flush , pipe about 2 M long with one brass coupling and clamps GI ,chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less thane 50grms. 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coats of red oxide primer etc. all complete as per specification and direction of E/I.

(A) 580 mm. long

(c) With 10 lit. low level PVC Cistem

Supplying, fitting and fixing 40mm high vitreous white glazed earthen E.W.C. with ‘p’ trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and direction of E/I.

(ii) E.W.C. with 'S' trap

(b) 10 lit. low level PVC Cistem

Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I.brass waste, 15 mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

(b)Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror.

(i) 600mm x 450mm size

(c)(iii) C.P. brass liquid soap container

Provinding and fixing wash basin wih C.I brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls whereever required : White Vitreous China Wash basin size 550x400 mm with a 15mm CP Brass single hole basin mixer

Providing and fixing white vitreous china laboratory sink with CI brackets , C.P brass chain with rubber plug 40 mm C.P brass waste and 40 mm CP brass trap with necessary C.P brass unions complete including painting of fittings and brackets , cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in charge.

Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete Flexible Pipe 32mm Dia

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing PTMT Bottle Trap for Wash basin. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms

Providing and fixing CP brass single lever low flow Sink mixer with 15 mm CP brass single lever pillar cock with pop up and waste complete including cutting and making good the walls where required.ROCA make (Model -RT5A3060C00) or Equivalent.

Providing and fixing C.P concealed four way diverter with thermostatic mixer with shut off valve and diverter, including cutting and making good the walls, wherever required. (Make:- Jaquar - Four way diverterKUB-35421, Thermostatic mixer 35671 or Equilent)

DRAINAGE INSTALLATIONS

Providing, fixing, testing and commissioning of UPVC SWR pipe type 'B' conforms to IS : 13592-1992 with all fittings such as bends, tees, elbow, 'Y', offset, cleaning pipe door, clamps etc. conforming to IS:14735-1999 and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592-1992 type 'B'. The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with rubber ring joint/solvent weld joint as required/applicable. 110 mm (OD)

Providing, fixing, testing and commissioning of UPVC 'P' trap/floor trap/urinal trap of self cleansing design having 50 mm water seal with or without horn conforming to IS : 14735-1999 including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 hard stone ballast 20 mm nominal size) including cost of cutting and making good the walls & floors wherever required. 110 mm inlet x110 mm outlet.

Providing, fixing, testing and commissioning of UPVC inlet fittings (hopper) receive waste from fixture waste with maximum 3 inlets 40, 50 & 63 mm OD size, fabricated from 110 OD UPVC SWR pipe, UPVC sockets, fixed to UPVC traps including solvent weld joint/rubber ring joint, complete with all civil work set in cement concreate 1:2:4 as required including cost of cutting and making good the walls & floors wherever required.

Providing, fixing, testing and commissioning of UPVC waste Pipe conforming to IS : 4985-2000 class III including all moulding fittings conforming to IS : 7834 (Part-1 - Part -7) 1987 such as tees, bends, reducers, coupling, adopters etc. solvent welded joint as per manufacturer recommendation including cutting and making good the walls, floors, R.C.C. work etc. (For fixtures waste).

Providing and fixing UPVC floor drain including all fitting and accessories fixed in cement mortar complete in all respect. 110 mm OD x 63 mm OD

Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. For 100mm dia. Pipe

Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) alround 100mm dia. SW / CI / waste pipes including bed concrete as per standard design

Providing, fixing, testing and commissioning of UPVC rain water pipes (IS : 4985-1983 class-III ) including injection moulded fittings (heavy duty) (plain or door) e.g. bends, junction, cowls, tees, offsets, access pieces etc. Clamps/Supports jointing with rubber ring/solvent cement joints including cutting chase or holes in walls and floors and making good as required at Site [For Balcony Drain + Terrace Rain Water Downtake Pipe]. 160 OD

WATER SUPPLY INSTALLATIONS

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (Exposed on wall Terrace)

32 mm dia, nominal bore

40 mm dia, nominal bore

Making connection of GI distribution branch with GI main of 50-80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. 25 to 40 mm nominal bore

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends)

25 mm dia, nominal bore

32 mm dia, nominal bore

40 mm dia, nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality

32 mm dia, nominal bore

40 mm dia, nominal bore

Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete.

20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931 15mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm dia nominal bore

Provide and fixing PTMT ball cock of approved quality, colour and make complete with epoxy coated aluminium rod with L.P/H.P.H.D. plastic ball

50 mm dia NB, 242mm long. Weighing not less than 1240 gms.

Providing and fixing chlorinated poly vinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fitting, including fixing the pipewith clampsat 1 m spacing. This includesjointing of pipes &fittingwith one step CPVC solvent cement and cost ofcutting chases and making good the same including testing ofjoints complete as per direction of Engineer in Charge.(Concealed work including cutting chases and making good the walls etc.)

15mm nominal outer dia. Pipes.

20mm nominal outer dia. Pipes.

25mm nominal outer dia. Pipes.

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :

50mm diameter

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified 100 mm nominal bore

50 mm dia.

Providing, laying, Jointing, Testing and commissioning of uPVC pressure pipes of 10Kg/Sqcm pressure rating class 5 (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation Including laying cement concrete 1:2:4 alround UPVC pipe including bed concrete and thrust blocks at bends as per standard design.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

Constructing masonry Chamber 60x45x50 cm,inside with 75 class designation brick work in cement mortar 1:5 (1 cement:5 fine sand) for water meter complete with C.I. Doble flap surface box 400x200x200mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

With F.P.S. bricks

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

SEWERAGE & DRAINAGE INSTALLATIONS UPTO MAIN ROAD FIRST MANHOLE

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete:

150 mm diameter

200 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

150 mm diameter S.W. pipe / RCC pipe

200 mm diameter S.W. pipe / RCC pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :

180 x 150mm size P-type

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensiions total weight of cover and frame to be not less than 38 Kg. ( weight of cover 23 Kg. and weight of frame 15 Kg.), with FPS bricks with class designation 7.5

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes: Size 90 x 80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :

For pipes 100 to 250 mm diameter

For pipes 350 to 450 mm diameter

Constructing brick masonry road gully chamber 50x45x60cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast RCC horizontal grating with frame complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

FIRE FIGHTING WORKS

PUMPS

1.NOC from fire authority shall be in the scope of Contractor . Only fee paid to the fire authority shall be reimbursed against the submission of the receipt and nothing shall be paid extra.

2. All the Fire Fighting works shall be done in compliance of Fire Fighting authority requirement.

Pump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65 % of rated head. The shut off head shall not exceed 120% of rated head.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520.

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

900 lpm at 35 m Head

CONTROL PANELS

Supplying,Installation,testing & commissioning of dust & vermin proof double door with canopy type taperd roof wall / floor mounted compartmentlised feeder piller type cubical control Panel for fire fighting terrace pump of front area not less than 1.0 Sqmtr. and depth not less than 300 mm, made out of 2mm thick CRCA sheet with 100 Amp. 4 strip aluminium bus bars with front openable door & locking arrangement, interconnection, control wiring, intrigation with pressure switch i/c suppying & fixing following switchgears & control gears/starters etc. as required.

Incomming

63 Amps. TP & N SFC with HRC fuses

Set of 3 phase indication lamp

Suitable HP fully automatic Star/Delta Starter with over load protection, current sensing type single phase preventor complete with all accessories and internal wiring required for automatic operation.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. It should be complete as per specifications & directions of Engineer-in-charge.

4 x 25 sqmm ( 28 mm )

3.5 x 50 sqmm ( 35 mm )

3 X 10 sq. mm (22mm)

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 150 mm width x 50mm depth x 1.6 mm thickness.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming to IS-7098. (Part-I).

4 core, 25 sq.mm. Aluminium Armoured

3.5 core, 50 sq.mm. Aluminium Armoured

4 core, 10 sq.mm. Aluminium Armoured

Supply and fixing in position 1 m wide Insulation mat made of elastomeric polymers Material (Class -A) of 415V grade as per IS 15642-2006 . Thickness of insulation mat shall be not less than 2 mm to withstand 1.1 KV dielectric strength AS PER IS 15652 : 2006. It should be complete as per specifications & directions of Engineer-in-charge.

PIPES & ACCESSORIES

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. ( For Underground )

150 mm. Dia

100 mm. Dia

80 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor)

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

50mm dia

65mm dia

80 mm dia

100 mm dia

150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

100 mm dia

150 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 40 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100mm dia

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.

Providing & Fixing of MS door made up of 16 gauge MS Sheet capable of accommodating fire hose reel, landing valve, hose pipes, fittings, 1 No. CO2 & 1 No. Dry podwer type portable fire extinguishers & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with one coat of primer & two coat of finished stove enamelled post office red colour paint & "FIRE HOSE" written on front. (Approx. size of door: 2100 mm HEIGHT, WIDTH OF DOOR AS PER SHAFT SIZE )

Providing and fixing hose cabinet of size 750mmX600X250mm made of 16 gause thick MS sheet with 4 mm thick float glass doors in front painted "FIRE" in red paint i/c recessary locking arrangement suitable to accommodate external hydrant with butterfly valve 2 nos. 15 mtr. long hose pipe. 1 no. brach pipe mounted on wall or raised brick platform & duly painted with post office red externally and white internally with synthetic enamel paint complete in all respects for external hydrant. as directed by Engineer-in-Charge.

Providing, Fixing, testing and commissioning of resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 11 Kg/cm2 and test pressure 16 Kg/cm2 to provide relief from stresses at pipe flanges.

150 mm dia

80 mm dia

Supply, fixing, testing and commissioning of screwed type brass/bronze lever operated ball valve of full flow with stainless steel ball (AISI 304 & spindle AISI 410) with setting & gland of superior quality having minimum working pressure of 16 kg/sqcm. 25 mm Dia

Providing and fixing 25 mm dia inspection & testing assembly with gun metal ball valve, gun metal sight glass ,Reducer ,union, G.I PIPE. connection to drain pipe/riser.

Supply and fixing of 4 Nos G.I round bottom FIRE BUCKET of 9 LTR. Capacity field with sand including proper supporting /mounting arrangement MS Angle Iron Frame painted by fire red colour over 2 coats of red oxide paint and written with white paint FIRE complete in all respects as per direction of Engineer Incharge .

FIRE EXTINGUSHER

Providing, storing, handling, shifting, installation, testing and commissioning of halon free portable fire Extinguishers as described below:

Concealed work, including cutting chases and making good the walls etc.

Providing and Fixing of CO2 Portable 4.5 Kg Fire extinguisher, Carbon-Dioxide type Flat base Horn Including Valve, High Pressure Rubber Wire Braided Discharge Hose of not less than 10 mm dia. & complete in all respects including initial fill with CO2 Gas confirming to IS:15222. and IS 15683:2018 Marked. Location : Inside FHC, Parking Area, Electrical Room, Pump Room,

Supply & Fixing of 6 Kg ABC MAP-50% Powder based Fire Extinguisher, Applicable Fire Class A, B & C, EPDM Rubber Hose, NRV Valve and Helium Leak Detection Tested, Internal Coating - Epoxy Powder and External Pure Polyester Powder Coated (UV resistant), IS 15683:2018 Marked. Location : Open General Area, Inside FHC, Parking Area, Basement

Supply & Fixing of 9 Kg ABC MAP-50% Powder based Fire Extinguisher, Applicable Fire Class A, B & C, EPDM Rubber Hose, NRV Valve and Helium Leak Detection Tested, Internal Coating - Epoxy Powder and External Pure Polyester Powder Coated (UV resistant), IS 15683:2018 Marked. Location : Open General Area, Inside FHC, Parking Area, Basement

Providing and Fixing of Portable 4kg Clean Agent HFC-236fa Fire Extinguisher, Gas UL Listed under EPA SNAP, EPDM Rubber Hose, NRV Valve and Helium Leak Detection Tested, Internal Coating - Epoxy Powder and External Pure Polyester Powder Coated (UV resistant), Suitable for Class A,B and C & Electrically Started Fires, Conforming to IS 15683:2018 Marked. Location : General Office Area, Inside of Critical Rooms i.e. Server Room, UPS Near Rooms, Fire Control Room etc.

Providing, fixing of 60 Ltr Mechanical Foam (AFFF-6%, Confirms to IS 4989 (Part-II), Trolley Mounted Fire Extinguishers, Fitted with 4 Metre EPDM Hose with SS Spring of 300mm & Air Aspirated Nozzle, CO2 Gas Cartridge of 300 Grams. Confirms to IS 4947, Brass Forged Cap, including all accessories complete in all respect. Applicable on Class A & B Fire, IS 16018:2012 Marked & CE Approved. Location : Near HSD Tank, DG Area

Providing and fixing Fire related signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc.

FURNITURE WORK

HOSTEL BED (WITH BOX):- Having an overall size of 1875mm x 900mm x 410mm. The Frame of the Bed is made of CRC ERW rectangular pipe of 50mm x 30mm size 1.5mm thickness. The Back rest of the bed is made of MS CRCA sheet of 2mm thickness. The bed has a modular construction the main frame having an overall size of 1770mm x 900mm is placed on a four 100mm x 100mm conical supports duly nut bolted to the head and leg side frame. The leg and head frame have a metal insert connector (pipe insert) 100mm long. The insert will add to the load bearing capacity of the bed. The bed shall have levellers made of nylon studs with screw inserts with adjustment of 10mm. HOSTEL BED BOX Dimensions:- Having an overall size of 1200mm x 840mm x 381mm. The Bed Box frame is a combination of 0.8mm and 1.0mm thick CRC steel sheet confirming to IS:513 grade D quality on the main body and top lid respectively. The top lid shall have minimum three and two stiffeners on the horizontal side and vertical side respectively. The lid has two hinges. Thus, having a load bearing capacity of 150 Kgs approx. The Legs of the storage box are made of 1.6mm thick CRCA MS sheet. The bed box shall have levellers made of nylon studs with screw inserts with adjustment of 10mm. Colour Available as per Client Choice- Brown, Blue, Orange, Green, Yellow With Glory Colour. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

MATTRES:- ECOAIR™ LATEX MATTRESS, Size -As per Bed, Double Sided, Removable Cover, Firm Fill Material-Memory Foam. Nilkamal Sleep Product Dimensions as per bed size specifications Pinhole technology for superior air circulation Latex foam for bouncy and supportive feel, alleviating body pain Removable and washable zipper cover Cool Tencel fabric for soft touch & comfort Durable & long lasting Warranty for 10 years. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

STUDENT CHAIR:- made of 25mm x 25mm round ERW CRC pipe with seat and back made out of 1mm thick MS CRC sheet duly perforated and powder coated in the desired shade. The Chair shall have levellers made of nylon studs with screw inserts with adjustment of 10mm. Colour Available as per Client Choice- Brown, Blue, Orange, Green, Yellow With Glory Colour. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

SS DINING TABLE 6 SEATER WITH FIXED CHAIR:- Overall size of the Dining Table 7’ L x 3’ W x 30” H total stainless steel (S.S) structure & body. Table top height is 30” from floor level and round type sitting stool height is 18” from floor level: all structures using 16-gauge S.S square frame (2” x 1”) and S.S sheet of 18 gauge with necessary bending and molding: Total 8 Nos. round sitting top (S.S) attached design in both sides. All S.S sheet will be SS 304 grade and 18-gauge (totally rust and moisture proof), pipe for sitting stool OD is 2” round S.S tube and table to tool pipe OD is 1 ½” (one and half inch) round S.S tube (16 gauge). Main Table Top thickness is 1”. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

CHR2061 Plastic Arm Chair:- Durable Plastic Body: The premium virgin plastic material on the armchair provides superior durability and a lightweight design for portability and long-lasting use. Comfortable Design: The ergonomic construction of the chair with supportive armrests and 125 kg load bearing capacity keeps you comfortable while sitting, even for extended hours. Contemporary Style: An aesthetic design with patterns offers an appealing touch to your chair, making your room feel more comfortable and welcoming. Glossy Finish: The elegant marble beige colour combines with a gloss finish to further accent the appeal of the chairs, making it a stylish complement to the decor. Multipurpose Use: The enduring plastic chair is suitable for outdoor and indoor settings. Dimensions(cm):- W57.5/D60/H79. Weight (Kg) 2.27. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

FACULTY MANAGER TABLE:- The Faculty Table shall be supplied in completely knock down conditions with an overall size (7 X 3 X 2.5) feet that is to be supplied, Installed & placed at site. The Faculty Table shall have the size made up of +19mm thick particle board. The top of table shall be guarded with toughened glass of 10mm at the top and provision of wire management. It shall include detachable side table (Pedestal unit) of (2.5 X 2 X 2.5) feet. All the locks bars shall be of reputed make. Faculty Table shall have the single drawer unit of the specification: (24 x 18) inch. The pedestal unit shall have drawer unit of the specification (24 x 18) inch and single door shelf with matching configuration. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

FACULTY MANAGER REVOLVING CHAIR:- Elevate workplace comfort with the Libra Office Chair. Precision-engineered high-back chair for luxury seating Quality PU cushioned seat and back feel super comfy Rest your arms on the soothing PU-covered armrests High load-bearing capacity with the Nylon star base Twin wheel castors glide smoothly for easy movement The elegant design with a tan shade exudes classSuitable for your office, home or commercial space Dimensions(cm):- W72/D72/H122 Weight (Kg) 17.7. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

FACULTY MANAGER VISITOR CHAIR:- Seat cushion made of Moulded PU Foam and Hot-Pressed Plywood Crepe fabric Upholtery Seat & back with edge PVC bedding Centre Tilt mechanism with upright locking Fixed Loop Armrest Powder coated MS base, the Hot-Pressed Plywood Seat BaseEnsures stability and years of reliable use. PVC Edge Bedding: Protects the chair from wear and tear. Cantilever Base Offers a sleek and modern design with a sturdy foundation. Dimenson(mm):- L530/D550/H840. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

FACULTY MANAGER OFFICE ALMIRAH:- Having an overall size of 1970 mm H x 900 mm W x 510 mm D. Steel sheet material CRCA sheets conforming to grade CRI of IS 513(part-1):2016 (with latest amendment). Generally conforming to BIS specification IS: 3312:2021 (with latest amendment) having Pedestal fitted with 3 mm Teflon Bush and Pedestal height of 125 mm. Number of Doors- 2, Number of hinges (for each door) 2, Number of shelves 4, Uniformly distributed load (UDL) for shelves 62 Kgs, Stiffener material MS sheet, Side, back, Top and Bottom Thickness- 0.8 mm, Shelves sheet Thickness-0.6 mm with 6 lever lock arrangement, Brass door handle. Body and Door Made of 0.8 mm thick (22 Gauge) Powder coated CRCA Sheet Back & Shelves made of 0.6 mm thick (24 Gauge) Powder coated CRCA Sheet. Finish with All the mild steel parts shall be given phosphating treatment Conforming to Class C of IS 3618. The process of application of phosphate coating Accordance with IS 6005. Powder coating with 50-micron thickness minimum Colour As per buyer's choice. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

FACULTY MANAGER OFFICE STEEL LOCKER:- 4 Compartment Storage Having an overall size of 1320 mm H x 620 mm W x 470 mm L. Steel sheet material CRCA sheets conforming to grade CRI of IS 513(part-1):2016 (with latest amendment). Generally conforming to BIS specification IS: 3312:2021 (with latest amendment) having Pedestal fitted with 3 mm Teflon Bush and Pedestal height of 125 mm Stiffener material MS sheet, Side, back, Top and Bottom Thickness- 0.8 mm, Brass door handle. Body and Door Made of 0.8 mm thick (22 Gauge) Powder coated CRCA Sheet Back and Powder coated CRCA Sheet. Finish with All the mild steel parts shall be given phosphating treatment Conforming to Class C of IS 3618. The process of application of phosphate coating Accordance with IS 6005. Powder coating with 50-micron thickness minimum Colour As per buyer's choice. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

MANAGER OFFICE TABLE:- This meticulously designed table emphasizes both functionality and aesthetics, featuring quality construction, stability measures, and a tasteful finish. Dimension(mm):- L1650/D1950/H750. Overroll Size for Table- L2100/D2250/H750. Quality Construction:25mm thick pre-laminated Particle Board used for the top and Gable End. Edge banding all around ensures a polished finish. Incorporates a reinforcement tube beneath the top to prevent sagging.Structural Elements: Features knock-down construction for streamlined assembly. 18mm thick pre-laminated Particle Board for the modesty panel. Gable foot brackets crafted from steel with nylon levelers. Aesthetic Enhancements: Includes decorative profiles and design elements for a sophisticated appearance. Cable Management: Equipped with an 8-module cable tray and access flap for seamless wire management. Standard Finishes: Available in Classic Walnut & Highland Pine. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

MANAGER OFFICE REVOLVING CHAIR:- The High Back Chair Shall be PU Upholstery Centre Tilt Mechanism, PU padded fixed polypropylene armrest Nylon Star Base Nylon Casters, Dimension(mm):- L700/D640/H1120 with cushion back style, adjustable height. Weight Bearing Capacity : 115 Kg, It shall have ergonomic design and shall contain Swivel, Rolling, Seat Lock, Cushion availability, Head Support. Padded Durable Arms and Good Quality Nylon Wheels.THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

MANAGER OFFICE VISITOR CHAIR:- The Visitor Chair Shall be Stainless steel frame for durability and stability PU foam seat and back for a comfortable seating experience PVC upholstery for a sleek and modern look 12 mm plywood in the back for added structure and stability Armrests to relax your hands and for a stable arm support SS Tubular Frame, PVC upholstered Seat and Back, PP Armrest for extra support and comfort, Nylon footcap, Dimensions(mm):-W550/D610/H790. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

FACULY ROOM & VISITOR ROOM SOFA 3 SEATER:- Aiden Sofa 3 Seater (Tan), Specification:- Constructed with durable pinewood and engineered wood with PVC legs for long-lasting reliability Features a contemporary design with soft foam seat and back for optimal comfort Double-layered wing design armrests with a short tufting in the centre of the back rest cushion for added elegance Tan-colour PVC upholstery for a leather look that is flame retardant, abrasion resistant, and UV resistance High backrest loose cushions for extra comfort, complemented by throw cushion for added style and cosiness. Color Tan StyleModern & Contemporary. Primary Material PVC Secondary Material Solid Wood (Pine Wood) + Engineered Wood (PLY) Legs Material PVC Product Weight 45 Kg. Dimensions(mm):- W2000/D900/H950/Seating Height-500. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

FACULY ROOM & VISITOR ROOM CENTER TABLE:- Allura Center Table (Walnut) Specification:- Crafted from robust and enduring rubberwood Melamine finish adds resistance and refinement Elegant marble paper coating on MDF tabletop An open shelf at the base offers storage spacePerfect for living rooms, receptions and offices Dimension(mm)- 900W/600D/455H. Primary Material Engineered Wood - Marble Paper Coating Secondary Material Solidwood - Rubberwood Product Weight22 Kg. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

LOBBY/VISITOR ROOM PUBLIC SEATING CHAIR:- Combination of Powder Coated and Chrome Plated Mild Steel 3 Seater Dimension(mm):- 1740L X 660D X 770H. Assembly Required: The product requires basic assembly and comes with assembly instructions Color: Shining Silver, Finish: Chrome Finish, Style: Contemporary. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

WASTBINS:- Easy to use & maintain Safeguards public health.Prevent diseases, safe for workers.Resistant to UV radiation.Available in Blue, Red, Green, YellowWheeled dustbin. ade from pure HDPE food grade Material. 100% virgin plastic with UV protected. Heavy Duty use with space saver design . Heavy duty use with specially designed bottom for minimizing The breakage & UV protected color for sun ray. Dimension(mm):- 510W X 380D X 950HCAPACITY : 120 Ltr. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

DRINKING WATER:- ZERO B Commercial Potable Water Purification System with Cooler 80Ltr RO+ESS+UV, Specification:- Certification for the product CE, Type of water purification technology RO+ESS+UV, Maximum Input Water TDS allow to the system 1000, Operation mode Fully automatic with auto cut off, Material of water Storage Tank Stainless Steel SS 304, Storage tank capacity up to float valve level (in liter) 80, RO Membrane rating 150 GPD, RO Membrane flushing Auto flush at every start, every stop and every one hour for 1 minutes, Particulate Filter size 10 inch, Particulate Filter Porosity 10 micron, Activated Carbon filter Size 10 inch, Recovery percentage at 27 degree centigrade 25-35, Filtration water capacity in liter/ hour 50, Body of filter Stainless Steel, Membrane Housing Yes, Number of candles 3, Type of compressor Reciprocating, Refrigerant Used HFC-R-134/A, Refrigeration temperature 15 to 17, Provision for Hot water No,Number of Cold Water Faucets 1, Number of Normal Water Faucets 1, Cooling capacity at comfort level (17 ± 1 degree celsius) (in liter per hour) 60, Installation Type Floor Mounted and Enclosed, Power supply SINGLE PHASE ( 230 ± 10 % VOLT,%0 Hz), Conformity to Standard For UV System From OEM IS-14724, Material of water storage tank Stainless steel SS-304, Ultraviolet UV Yes, Prevention of bacteriological growth(EPS) System sanitizer to keep stored water safe against bacteriological growth for 24X7, EPS Patent Certificate.

Bed Side Locker has cabinet with lock and with plastic molded handle. There is space between plastic top and cabinet to keep the general items for the frequent use. Cabinet is provided with lock to keep the valuable items for the safety.Overall Size (in mm): 490L x 410W x 941H Material Specifications:4Corner Tube made from ERW Round Tube of Section Æ 25.4mm having thickness 1.2mm.4Cabinet made from 0.8mm thick CRCA Sheet, and is provided with lock. 4Top made from ABS of Section 2.2mm. Top has recessed and contoured shape for the better aesthic and usability.4Knob made from Plastic molded knob with Matt finish with generous radii and dome shape for better grip.4Castors of Section Æ 50mm made from Plastic molded castor placed in diagonal lokcing arrangement.Finish Specification:Anti microbial and thermosetting eproxy polyester Powder coating, formulated to fulfill the requirements for bacterial protection. Colour RAL White & Plastic parts in Grey.Performance Specification:Maximum safe working load - 5kg (on Top) + 5kg (On Middle) + 10Kg (on Bottom). THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

THREE-FOLD SCREEN WITH CLOTH:- Dimensions: 2300mm (L) X 1690mm (H) Sturdy Construction:- Constructed with a Strong Tubular Frame Made of Mild Steel ERW Material. Convenient Accessibility:- Comprises a Total of Three Panels: Middle Panel Measuring 1220mm and Two Narrower Side panels, Each 550mm Wide:-Each Side Panel is Equipped with Four Hooks for Convenience. Enhanced Mobility: ·Mounted on Four 50mm Dia Castors Without Brakes for Easy Movement. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

SALINE STAND (CASTORS BASE):- Dimensions: 300mm (DIA) * 1350mm to 2150mm (H) – Adjustable Stainless Steel Rod Sturdy Construction:- Sturdy Construction from Mild Steel ERW Tubular Material. Convenient Accessibility: Height-Adjustable Stainless Steel Saline Rod Featuring Two Hooks. Enhanced Mobility:- Supported by a Mild Steel Base with 50mm Dia Castors for Easy Movement. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

Hospital Sheet Bed- Overall Sizes: (L)2268 mm X ( W)922 mm X (H) 610 mm Description: Sheet Bed should be a plain bed used in the recovery ward. Material Specifications: Under Structure has a Higher diameter tube which should provide a sturdy understructure.Lying surface area of CRCA Finish Specifications: Head Board/Leg Board should be made of frame MS ERW RoundTube of sections Ø19, Ø25.4& Ø31.75mm, of thickness1.6 mm Provision for mounting of IV Pole and Mosquito Net pole should be present Finish Specifications: Powder coating should be Bacteriostatic and thermosetting epoxy Polyester, formulated to fulfill the requirements for bacterial protection. All powder coated parts in RAL white Performance Specifications: Maximum patient load should be 135 kg. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

Mattress for ICU Bed:- 4 Section Mattress 100mm thk. FOAM Density: 40±2 kg/m3 & Hardness in Kg: 45±2 as per IS:7888 for 25% Compression. UPHOLSTRY Stitched Upholstry Cover Material: Helium Heavy A/F F/R SM with Fire Retardent and Antimicrobial Properties. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

Bed Side Locker has cabinet with lock and with plastic molded handle. There is space between plastic top and cabinet to keep the general items for the frequent use. Cabinet is provided with lock to keep the valuable items for the safety.Overall Size (in mm): 490L x 410W x 941H Material Specifications:4Corner Tube made from ERW Round Tube of Section Æ 25.4mm having thickness 1.2mm.4Cabinet made from 0.8mm thick CRCA Sheet, and is provided with lock. 4Top made from ABS of Section 2.2mm. Top has recessed and contoured shape for the better aesthic and usability.4Knob made from Plastic molded knob with Matt finish with generous radii and dome shape for better grip.4Castors of Section Æ 50mm made from Plastic molded castor placed in diagonal lokcing arrangement.Finish Specification:Anti microbial and thermosetting eproxy polyester Powder coating, formulated to fulfill the requirements for bacterial protection. Colour RAL White & Plastic parts in Grey.Performance Specification:Maximum safe working load - 5kg (on Top) + 5kg (On Middle) + 10Kg (on Bottom). THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

Patient Trolley With Removable Stretcher:- Removable stretcher top on CR, ERW tubular steel trolley mobile on four 15 cms dia swivel castors, two with brakes. Provided with O cylinder carrier.Pretreated and powder epoxy finish. Two 2 locations for drip rod. Overall Size: 215(L) x 65(W) x 82(H) cms (without mattress). Stretcher Size: 182(L) x 55(W) cms (without handle). Supplied in Knock Down Condition. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

Wheel Chair:- Folding Type, Self Propelling, Pretreated & Epoxy Powder Coated Tubular Frame Work, Foldable Aluminum Foot Rests on the Fixed Leg Rests with Fixed, comfortable Arm Rests, Weight Carring Capacity 120 kg. (Approx). Front Swivel Castors of 20 cms. Rear Soild tyres of 60 cms, with Brakes, Strong Washable Seat & Back, Seat Width : 46 cm, Seat Depth : 45 cm. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

Kick Bucket (SS):-Stainless Steel Frame, Deep Container, all round bumper. Mounted on Three Ø 7.5cms swivel castors. Overall Size: Ø 34 x 34(H) cms. Container Capacity: 10 Litres. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

HORTICULTURE WORK

Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment)

Screened through sieve of IS designation 20 mm

Screened through sieve of IS designation 16 mm

Screened through sieve of IS designation 4.75 mm

Supplying and stacking of well decayed cow dung manure at site including royalty and carriage up to 1.0 km (cow dung manure measured in stacks will reduced by 8% for Payment)

PREPARATION WORKS

Fine dressing of the ground

Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-in-charge

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Engineer-in-charge (cost of sludge, dump manure and / or good earth to be paid separately).

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m diameter and 1.2 m deep

Holes 90 cm diameter and 90 cm deep

Holes 60 cm diameter and 60 cm deep

Holes 45 cm diameter and 45 cm deep

MAINTAINANCE WORK

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing, weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge.

TREES

Delonix regia Gulmohar / April fool

Cassia fistula Amaltash

Pterospermum acerifolium Makchund

Ficus religiosa peepal

Ficus benghalensis bargad / banyan

Cestrum nocturnum raat rani

Azadirachta Indica Neem

Bauhinia purpurea Kachnar

Callistemon lanceolatus Bottle brush

Spathodea campanulata rugtoora

Plumeria alba white champa

Plumeria rubra pink champa

Lagerstroemia flosreginae jarul

Polyalthia longifolia Ashok

Tectona grandis sal

Tamarindus indica Imli

Mangifera indica Mango

Eugenia jambolana Jamun

Phyllanthus emblica Amla

foxtail palm

Bottle palm

BAMBOO

Buddha belly bamboo

SHRUBS

Clerodendrum inerme Volkameria inermis

Ficus panda

Ficus benjamina Starlight Ficus Starlight

Gardenia jasminoides

Golden duranta

Hamelia patens

Hibiscus rosa-sinensis udhul

Raphis excelsa lady palm

Tecoma gaudichaudi Yellow bells

TMC dwarf Chandani

Canna dwarf

GROUND COVERS

Alternanthera red

Chlorophytum comosum

Jatropha

Sprenger's asparagus Foxtail fern

Syngonium podophyllum Syngonium butterfly

Tradescantia pallida

GRASS

Cynodon dactylon doob grass

Labour Cess @1%

Please Enable Macros to View BoQ information