Repairing and rewinding of monoblock pumps for urban water supply scheme under sub division Hanumangarh town

Repairing and rewinding of monoblock pumps for urban water supply scheme under sub division Hanumangarh town

Rewinding of three phase squirrel cage induction motor of Monoblock pump sets including all necessary material and of the same characteristics as original with required size of super enameled copper wire (including cost of copper wire),'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including transportation of motor pump to and from Div/AEn/JEn store complete as per direction of engineer in charge.

Upto 5 H.P.

SUPPLY & FIXING OF SPARE PARTS FOR MONOBLOCK PUMPSET (MOTOR + PUMP

Connection Plates

up to 10 HP

Cooling Fan

up to 10 HP

GM/SS bush

Upto 10 HP

Mechanical reconditioning of Bearing sheet

Upto 10 HP

Mechanical reconditioning of Impeller sheet and Key way slot

Upto 10 HP

Oil seal

Upto 10 HP

Labour charge for opening and fitting of pump sets

Upto 10 HP

Rewinding of three phase squirrel cage induction motor of HSC pump sets including all necessary material and of the same characteristics as original with required size of super enamelled copper wire (including cost of copper wire) 'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including making electric connection at site of installation of motor with starter, alignment with pump sets and transportation to and fro from installation site complete as per direction of engineer in charge at site.

Above 30.00 HP & upto 35.00 HP

Above 35.00 HP & upto 40.00 HP

Above 75.00 HP & upto 100.00 HP

SUPPLY & FIXING OF SPARE PARTS HSC PUMP SETS (MOTOR + PUMP)

Connection Plates

30 HP to 50 HP

Above 50 HP to 100 HP

Cooling Fan

30 HP to 50 HP

Above 50 HP to 100 HP

Fan Cover

30 HP to 50 HP

Above 50 HP to 100 HP

G.M./SS Gland Guide Bush

30 HP to 50 HP

Above 50 HP to 100 HP

Shaft with Sleeve Chuck Nut

30 HP to 50 HP

Above 50 HP to 275 HP

Bush Shaft Sleeve of G.M.

30 HP to 50 HP

Above 50 HP to 100 HP

G.M. Gland Cover

30 HP to 50 HP

Above 50 HP to 100 HP

S.S. Shaft (Non Magnetic)

30 HP to 50 HP

Above 50 HP to 100 HP

M.S. Shaft Check Nut

30 HP to 50 HP

Above 50 HP to 100 HP

JOB WORK FOR REPAIR OF PUMP MOTOR

Bearing Housing (rebuilding, turning & finishing)

30 HP to 50 HP

Above 50 HP to 100 HP

Bearing Cap (rebuilding, turning & finishing)

30 HP to 50 HP

Above 50 HP to 100 HP

Impeller Reconditioning for all type of Pump

30 HP to 50 HP

Above 50 HP to 100 HP

Labour Charges for Dismantling & Assembling of Pump

30 HP to 50 HP

Above 50 HP to 100 HP

Coupling with stud and rubber bush

30 HP to 50 HP

Above 50 HP to 100 HP

Supply & Fixing of tyre coupling sets according to relevant IS code in Centrifugal couple pump sets of approved make Unit. This job also included re-alignment of centrifugal couple pump set after fixing of tyre coupling set as per directed by Engineer-in charge

Type 16 Nos. set

Type 17 Nos. set

Supply and fixing Ball bearing of Various size for centrifugal/monoblock pump set of ISI Mark as per specification and approved make by EIC.

6308 or equivalent size

6309 or equivalent size

6310 or equivalent size

6311 or equivalent size

6312 or equivalent size

Routine maintenance of centrifugal coupled pump and motor including opening, cleaning, greasing and refitting / changing of ball bearing if required, gland refilling and replacing all rusted studs, replacing rubber bushes & coupling nut & bolts for coupling pulley, tightening all nut & bolts of foundation,baseplate, pump & motor etc. Checking & correcting alignment of pump & motor including necessary materials i.e. grease, nut & bolts, studs, washers, gland packing and rubber bushes etc.work done at site complete job

5 HP to 20 HP

Above 30 HP and up to 50 HP

Above 50 HP and up to 100 HP

Cleaning of pump house by air blower/ vacuum cleaner or other means including removing of JALA from ceiling and walls etc. complete Job.

Cleaning of Electric Panel PMCC by air blower/vacuum cleaner or other means including tightening of loose connections etc. complete job.

Replacing of damaged/broken gland packing plate with new gland packing plate suitable for centrifugal pump shafts and nut&bolts etc. complete job.

5 HP to 20 HP

Above 30 HP and up to 50 HP

Above 50 HP and up to 100 HP

Turning of various sizes of CID Joints Class- 10/ 15 Complete set (Labour Charges), The Joints will be supplied by the Junior Engineer concern of Department and carting to workshop and after turning of these joints, firm is liable to transport upto Junior Engineer concern's store own his cost.

80 mm dia

100 mm dia

125 mm dia

150 mm dia

200 mm dia

250 mm dia

Providing, Fabrication of Mild Steel Plane Ended/ Flanged Specials like Tees, Bends, Reducers, Enlargers, Plugs, Tail Pieces and Blank Flange made from MS pipes, MS sheet strip and MS Sheet of required sizes by welding, cutting and treading as per site conditions and as directed by the Engineer- In- Charge complete in all respect.

Supplying and fixing of MS Rods for different sizes of sluice valve and should be supplied as according to size of old rods including material and finishing for the following sizes.

Sluice Valve Size 80mm

Sluice Valve Size 100mm

Sluice Valve Size 125mm

Sluice Valve Size 150mm

Sluice Valve Size 200mm

Supplying of Chuck Nut for different sizes of sluice valve and should be supplied as according to size of Check Nut including material for the following sizes.

Sluice Valve Size 80mm

Sluice Valve Size 100mm

Sluice Valve Size 125mm

Sluice Valve Size 150mm

Sluice Valve Size 200mm

Providing of U Plate (U Stand) for different sizes of sluice valve and should be supplied as according to size of old U Plate including material for the following sizes.

Sluice Valve Size 80mm

Sluice Valve Size 100mm

Sluice Valve Size 125mm

Sluice Valve Size 150mm

Sluice Valve Size 200mm

Please Enable Macros to View BoQ information