Signalling work in connection with SDAH Division -Provision of Track Machine Siding -12 Nos along with CTR(P) - 20.909 TKM & TRR(P) - 4.404 TKM , CTR(P)- 4.123, TRR(P)-27.395 TKM & TTR (FS+TWS+WCMSC)-3 Set (1 in 12) in Sealdah Division.

HAS BEEN SHOWN IN ITEM BREAKUP SEPARATELY.

NON-SCHEDULE/SOR ITEM vide SL. NO. 1 to 172 GIVEN IN SCHEDULE OF WORK. GST HAS BEEN

SHOWN IN ITEM BREAKUP SEPARATELY.

S No. Item Description of Item Unit Qty Rate Amount

SEALDAH DIVISION-S AND T/EASTERN RLY

1 1 "Dismantling & releasing of existing detection Set 60.00 3251.56 195093.60

point or track device ( TX / RX) of SSDAC /

HASSDAC/ MSDAC of any make with deflector

and re-fixing of existing/ fixing of new

detection point (in case of new detection

point, the same will be supplied by the

railway), including marking & drilling of hole

on rail along with deflector fixing, adjustment

of all electrical parameters as per manual of

concerned SSDAC / HASSDAC / MSDAC and/

or the instruction of Rly. site engineer.

Necessary tools, marking Zig along with Dril

Bit ( as per SSDAC / HASSDAC / MSDAC) for

this job will be arranged by the contractor

himself. The work will be done in connection

with replacement of rail/ on existing rail/PQRS

works etc.. NOTE : 'SET' in unit column

indicates per detection point or track device."

2 2 "Dismantling / releasing of existing detection Set 60.00 2496.31 149778.60

point or track device ( TX / RX) of SSDAC /

HASSDAC/ MSDAC of any make with deflector

and re-fixing of existing new detection

pointon rail. Adjustment of all electrical

parameters as per manual of concerned

SSDAC / HASSDAC/ MSDAC / or the instruction

of Rly. site engineer. Necessary tools for this

job will be arranged by the contractor

himself. The work will be done in connection

with Engineering Machine works . NOTE : (i)

'SET' in unit column indicates per detection

point or track device. (ii) New material will be

supplied by railway."

3 3 "Supply of Track Lead Junction Box(TLJB) of Numbers 255.00 3020.34 770186.70

size 250 X 255 X 120 mm FRP based of ARA

Type, material including brass bolts and

hylam board sheet with terminals etc.

Technical Specification as per Drg. No.

SI/TYP/0096 or latest. (Drawing attached)

Inspection: RITES"

4 4 "Erection, Fitting and Rail connection of Track Numbers 255.00 1115.25 284388.75

Lead Junction Box on two supports (FRP

stumps) with contractor's fixing material. This

will include drilling of holes for track lead/side

connections on rail. The work shall be done as

per instructions of Rly engineer at site"

5 5 "Dismantling of existing point fittings, drilling Set 23.00 7029.66 161682.18

of holes in stock rail/tongue rail/ gauge tie

plate, re-arrangement and re-fixing of

existing electrical detector and installation of

IRS 24/2002 with latest Amdt. point machine

on MS plate fixed on wooden/concrete

sleepers complete with fixing of point JB

ground connections including smithy job for

welding & termination & wiring of point

machine, adjustment and testing as per

technical specification and dismantling of all

new fittings excluding point machine and

marking with paint for future and

transportation up to railway's store."

SEALDAH DIVISION-S AND T/EASTERN RLY

6 6 PRELIMINARY ADJUSTMENT FOR OPERATION Job 41.00 1802.20 73890.20

OF POINT BY CRANK HANDLE, ADJUSTMENT

OF LOCK & DETECTION SLIDES AS PER LH/ RH

POSITION OF THE POINT MACHINE, OILING OF

EXISTING NUTS, BOLTS OF EXISTING POINT

MACHINE. PRELINMINARY WORK RELATED TO

THIS JOB TO BE DONE ON SAME DAY/

PREVIOUS DAY AS PER INSTRUCTION OF

RAILWAY SITE ENGINEEER. THIS JOB ALSO

INCLUDES TRANSPORTATION OF NEW POINT

MACHINE (TO BE SUPPLIED BY THE RAILWAY)

FROM STATION/ STORE/ CUSTODY OF

CONCERNED JE/SSE/SIGNAL/SECTION TO

ACTUAL SITE OF WORK.

7 7 Dismantling of point machine with ground Numbers 3.00 990.68 2972.04

connection including point JB.

8 8 "Supply of Ground Connection [BG] Threaded Numbers 26.00 5691.53 147979.78

Type for IRS type Point Machine, as per

CWM/Signal Workshop/Howrah/E. Rly.

drawing number, Sl.No., Description of

Drawing & CWM/SW/HWH's Drawing No.

mentioned below: - 1. Detector Rod (Far End)

- BS/29/721 with ALT-1 Detector Rod (Near

End)- BS/29/722 with ALT-1. 2. Lock Rod (Far

End) - BS/29/723 with ALT-1, Lock Rod (Near

End) - BS/29/724 with ALT-1. 3. Switch

Extension Bracket - BS/29/725 with ALT-1. 4.

Drive Rod - BS/29/726 with ALT-1 Drive Lug-

BS/29/726 A with ALT-1. 5. Sleeve- BS/29/726

B with ALT-1. 6. Lug- BS/29/726 C with ALT-1.

7. Pin- BS/29/726 D with ALT-1. 8. Sketch

showing the Layout arrangement- BS/29/727

with ALT-1. Amdt. and alt. up to date if any.

Ordinary Turn Out Inspection : Consignee"

9 9 "Supply of Ground Connection [BG] Threaded Numbers 4.00 13563.56 54254.24

Type for IRS type Point Machine, as per

CWM/Signal Workshop/Howrah/E. Rly.

drawing number, Sl.No., Description of

Drawing & CWM/SW/HWH's Drawing No.

mentioned below: - 1. Detector Rod (Far End)

- BS/29/721 with ALT-1 Detector Rod (Near

End)- BS/29/722 with ALT-1. 2. Lock Rod (Far

End) - BS/29/723 with ALT-1, Lock Rod (Near

End) - BS/29/724 with ALT-1. 3. Switch

Extension Bracket - BS/29/725 with ALT-1. 4.

Drive Rod - BS/29/726 with ALT-1 Drive Lug-

BS/29/726 A with ALT-1. 5. Sleeve- BS/29/726

B with ALT-1. 6. Lug- BS/29/726 C with ALT-1.

7. Pin- BS/29/726 D with ALT-1. 8. Sketch

showing the Layout arrangement- BS/29/727

with ALT-1. Amdt. and alt. up to date if any.

Double Slip as per DRG

No.SGW/S/2/HWH/1/92 or Latest. Inspection :

10 10 "Supply of Electric Point machine IRS type Numbers 3.00 111156.78 333470.34

220 mm throw,high thrust (AC immunity

160V AC), non-trailable to operate on 110V,

DC complete with Lock and Detector slides,

Cable Termination Box and clamp lock 60 Kg.

confirming to IRS: S/24/2002 & Assy. Drg. No.

RDSO-S/11000 & For Motor IRS: S/37/82.

(items to be procured through stores).

Inspection: RDSO"

SEALDAH DIVISION-S AND T/EASTERN RLY

11 11 "Supply of Electric Point Machine-IRS type, Numbers 15.00 55609.32 834139.80

(AC Immunity 160V AC), Non-Trailable to

operate on 110V DC complete with Lock and

Detector slides, Cable Termination Box

(143mm throw, thrust as applicable, Rotary

locking), confirming to IRS: S 24/2002

(amdt.1) (Amdt. up to date if any) & Assy.

Drg. No. RDSO-S/10910 (alt. up to date if any)

& IRS:S 37/82 (amdt.3) (Amdt. up to date if

any) for Motor. Inspection : RDSO"

12 12 "Installation of Electric Point Machines on MS Numbers 163.00 8819.49 1437576.87

plate fixed on wooden/ concrete sleepers

complete with fixing of junction boxes,

ground connections of 220mm & 143mm

both including smithy works involved,

insulation of MS plate on which the point

machine is to be fixed from the gauge tie

plate involving riveting/welding of angle

cleats, installation of point JB, termination

adjustment for operation of points by crank

handle, painting and lettering as required

including wiring, testing and commissioning.

Note: MS plate/flat/angle /angle cleats,

paints, bolts & nuts and washers of sizes as

required for fixing the point machine shall be

supplied by the contractor except point

machine. Note : i) Point Machine & Ground

Fittings to be supplied by Rly. ii) Dismantling

and refixxing of existing EPD in case of

DoobleSlip/Diamond Xing"

13 13 "Supply of Point insulation Complete set as Set 211.00 1044.07 220298.77

per RDSO/SPN/168/2005 for 1.Switch

bracket'D' bracket insulation for IRS point

machine - One set comprises of (a)Side plate

LH to Drg.No.S-3266 - 1 No. (b)Side plate RH

to Drg.No.S-3265 - 1 No. (c)Insulating bush to

Drg.No.S-3199 - 4 Nos. (d) Insulating washer

to Drg.No.S-8640 - 4 Nos., 2.Split-Stretcher

bar 2.1 Insulation for Leading stretcher

bars(BG) each set comprising of (a) Insulating

plate for leading insulated stretcher bars BG

as per RDSO Drg.No.T-10384 - 2 Nos. (b)

Insulating bushing for leading insulated

stretcher bars for BG as per RDSO Drg.No.T-

10535- 4 Nos. (c) Insulating Washer for

insulated stretcher bar BG as per RDSO

drg.No.T-10371 - 6 Nos. 2.2 Insulation for

following stretcher bars BG. Each set

comprising of: (a) Insulating side plate for

insulated stretcher bars BG as per RDSO

Drg.No.T-10367 - 3 No. (b) Insulating bushing

for insulated stretcher bars BG as per RDSO

Drg.No..T-10368 - 6 Nos. (c) Insulating

washer for insulated stretcher bars BG as per

RDSO Drg.No.T10371 - 12 Nos. 2.3 Insulation

of 'L' Bracket & 3. Gauge tie plates (52

Kg/60Kg as per site requirement) Insulation

for (BG) complete with insulating bush and

washereach set comprising of: (a) Insulating

plate for insulated tie plate BG as per RDSO

Drg.No.T-10372-1 No. (b) Insulating bushing

for insulated stretcher bar BG as per RDSO

Drg.No.T10368 - 3 Nos. (c) Insulating Washer

for insulated stretcher bar BG to IRS 40/84 as

per RDSO drg.No.T-10371 - 6 Nos. Inspection:

Consignee subject to procurement from RDSO

approved vendors"

14 14 Installation & commissioning of Point Numbers 211.00 2269.23 478807.53

insulation Complete set as per

RDSO/SPN/168/2005

SEALDAH DIVISION-S AND T/EASTERN RLY

15 15 "Supply of Point JB fitted with 18 no.1-way Numbers 203.00 3508.47 712219.41

terminal Block confirming to IRS-S 75/91

(AMD-2) or latest,Drg.no. SA-23741A with 3

nos. of 40 MM bore GI pipe 600 MM long as

per DRG No. SGW/MGS/PT4/91 fixed on

Hylum sheet with U channel (75x40x1500)

MM for fixing ARA terminal to be procured

from RDSO approved Sources. Inspection :

16 16 "Supply of Channel Pins MS (Galvanized) Numbers 2700.00 3.39 9153.00

single groove, 7 mm suitable for 4mm dia

bonding wire as per spec No IRS S 17 & RDSO

Drg No. S-69/M. Inspection: Consignee. "

17 17 "Supply of GI wire 8 SWG (4mm dia) suitable Numbers 851.00 10.17 8654.67

for track circuit rail bonding(1.5mts length)

Inspection: Consignee "

18 18 "Supply & installation of polymer positive Numbers 325.00 66.95 21758.75

temperature coefficient device (PPTC)

resettable fuses, for outdoor circuits.

30V/2.5A for track feed and 60V/1.1A in place

of 24V/2A fuse and 120V/1.1A for signal

lighting. Make- RAYCHEM, BOURNS, LITTLE

FUSE, FUZETEC or TYCO. Quantity as per site

engineer. Note- PPTC fuses are to be

connected with crimped ring type lugs. "".

Inspection: Consignee."

19 19 "Supply of Surge Protection Device (SPD) , Numbers 4.00 2204.72 8818.88

class-II,C-TYPE for 24-60 VOLT DC as per

RDSO Spec No. RDSO/SPN/TC/215/2018

Ver.2.0 (or latest) Class No. 3.12.3 .along

with indication between L1-L2, L1-E and L2-E,

pluggability and potential free contact for

remote monitoring between L1-L2, L1-E and

L2-E are mandatory, product should be UL

certified. Note - No. in Unit column consists of

3 nos individual SPD modules with common /

seperate base. Make- Phoenix contact /JMV/

OBO/ SALTEK/ Railway Technology.

Inspection : Consignee"

and 5101/69 or latest Inspection: Consignee"

21 21 "Supply of HSS Twist Drill Bit 13mm Note : 1 Set 33.00 359.32 11857.56

set consists of 10 piece of Drill Bit.

Inspection: Consignee"

22 22 "Provision/Installation of Bonding with GI wire Numbers 910.00 152.54 138811.40

4mm dia (8 SWG) for track jumper & fish

plate joints bonds. This will include drilling of

7.0/7.1/7.2 mm dia. holes in rails (4 Nos.) and

provision of two jumpers for each bond,

clipping of bonds etc. with contractors own

tools as per instruction of Rly. Engineer at

site. Inspection : Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

23 23 "Cleaning , Scrubbing and Paining after Numbers 185.00 458.00 84730.00

application of primer, of MAIN SIGNAL Post,

including base, unit, ladder stage and all

fittings ( This includes calling-on signal,

Dependent shunt signal, Junctiuon type route

indicator, Goods warning board, Cross marks

etc. Concerned colours to be as per signal

engineering manual. All the required paints

and materials are to be supplied by the

contractor. Note: Paints to be purchased from

reputed company like Asian

Paints/Berger/Shalimar for this Job. Grade of

the required paint is to be as per the

following spec. Alluminium:-IS:2339/63 with

AMDT. 1 or latest. Black:- IS:8662/93 or

latest. Golden yellow:- ISS:356 & IS:8662 or

latest. Red oxide:- ISC:446 & IS:123/62 with

AMDT.1 or latest. Inspection: Consignee."

24 24 "Cleaning , Scrubbing and Paining after Numbers 490.00 359.00 175910.00

application of primer, of Full Size Location

Box complete, Concerned colours to be as per

signal engineering manual. All the required

paints and materials are to be supplied by

the contractor. Note: Paints to be purchased

from reputed company like Asian

Paints/Berger/Shalimar for this Job. Grade of

the required paint is to be as per the

following spec. Alluminium:-IS:2339/63 with

AMDT. 1 or latest. Black:- IS:8662/93 or

latest. Golden yellow:- ISS:356 & IS:8662 or

latest. Red oxide:- ISC:446 & IS:123/62 with

AMDT.1 or latest. Inspection: Consignee."

25 25 "AUGMENTATION AS WELL AS REPAIRING OF Numbers 65.00 16387.00 1065155.00

THE EXISTING FULL SIZE APPARATUS CASE

WITH FRP COAT FOR OUTSIDE OF THE

APPARATUS CASE ALONG WITH RENOVATION

OF THE EXISTING FOUNDATION OF THE

APPARATUS CASE. THIS INCLUDES COST OF

PAINTING OF THE APPARATUS CASE, AND

REQUIRED FRP COATING, M.S. ANGLE, NUTS

& BOLTS, MASONRY MATERIALS i.e. SAND,

CEMENT, STONE CHIPS, ETC. NOTE : 'NO.' IN

UNIT COLUMN INDICATES 'APPARATUS CASE'.

26 26 "Supply of UNDERGROUND, ARMOURED, Kilometre 3.00 107998.00 323994.00

UNSCREENED, RAILWAY SIGNALLING CABLE

(PVC INSULATED,COPPER CONDUCTOR OF

SPECIFICATION. NO. IRS:S-63/2014 (REV. 4.0)

OR LATEST OF SIZE 2 CORE X 2.5 SQ. MM,

Inspection :- RDSO."

27 27 "Supply of complete Pedestal for ELB LC gate Set 10.00 169071.50 1690715.00

Note :- 1 Set consists of 'A' Side and 'B'Side

pedestal of a single Gate Inspection:

28 28 "SUPPLY OF BOOM SECTION FABRICATED Numbers 9.00 2600.00 23400.00

FROM G.I SHEETS OCTAGONAL SHAPE, FIRST

SECTION FOR ELB AS PER SPECIFICATION NO.

RDSO/SPN/208/2012 VERSION 2.0 OR LATEST

Inspection: Consignee"

29 29 "SUPPLY OF BOOM SECTION FABRICATED Numbers 45.00 2300.00 103500.00

FROM G.I SHEETS OCTAGONAL SHAPE,

SECOND SECTION FOR ELB AS PER

SPECIFICATION NO. RDSO/SPN/208/2012

VERSION 2.0 OR LATEST Inspection:

30 30 "SUPPLY OF BOOM SECTION FABRICATED Numbers 45.00 2000.00 90000.00

FROM G.I SHEETS OCTAGONAL SHAPE, THIRD

SECTION FOR ELB AS PER SPECIFICATION NO.

RDSO/SPN/208/2012 VERSION 2.0 OR LATEST

Inspection: Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

31 31 "SUPPLY OF BOOM SECTION FABRICATED Numbers 8.00 1800.00 14400.00

FROM G.I SHEETS OCTAGONAL SHAPE,

FOURTH SECTION FOR ELB AS PER

SPECIFICATION NO. RDSO/SPN/208/2012

VERSION 2.0 OR LATEST Inspection:

32 32 "Supply of Rotary switch compatible for Numbers 30.00 850.00 25500.00

Deltron make Domino type control cum

indication LC Gate panel. Inspection:

33 33 "Supply of Limit Switch Set (2 NO, 2NC) for Set 45.00 1103.39 49652.55

boom lock proving. The material will be as

No.RDSO/SPN/208/2012/Ver.2.0 and

Amendment 1 or latest. Inspection :

34 34 "SUPPLY OF LIMIT SWITCH LS1 AND LS2 Numbers 45.00 749.00 33705.00

J02TPRA, 2NO 2NC - 1 NO.or J01TPRA, 1NO

1NC - 1 NO. FOR GEAR BOX OF PEDESTAL, AS

SPARE PARTS FOR ELECTRICALLY OPERATED

LIFTING BARRIER GATE AS PER RDSO

SPECIFICATION NO. RDSO/SPN/208/2012,

VER. 2.0 OR LATEST. THIS INCLUDES

DISMANTLING & RELEASING OF THE EXISTING

PORTION. INSPECTION : CONSIGNEE."

35 35 "SUPPLY OF HEAD LOCK LIMIT SWITCH JLSLA- Numbers 24.00 1180.00 28320.00

2NO. 2NC. FOR MOTORIZED LOCK BOX, AS

SPARE PARTS FOR ELECTRICALLY OPERATED

LIFTING BARRIER GATE AS PER RDSO

SPECIFICATION NO. RDSO/SPN/208/2012,

VER. 2.0 OR LATEST. THIS INCLUDES

DISMANTLING & RELEASING OF THE EXISTING

P O RT I O N . MAKE : JAIBALAJI/ SIMILAR.

INSPECTION : CONSIGNEE."

36 36 "Supply of magneto telephones Desk type Numbers 2.00 2973.73 5947.46

with all accessories including supply of 2 nos.

Dry cell for each telephone with wooden

battery box. (i) SPEC.FOR magneto telephone

- IRS-TC-36-97 with AMD-1 OR LATEST.

Inspection : Consignee"

37 37 Installation of magneto / control telephone, Numbers 2.00 165.25 330.50

annunciator with all accessories and dry cells

(2 nos.) with wooden battery box.

38 38 "Supply of Disconnect Terminal Block, Screw Numbers 200.00 46.61 9322.00

less type, 4-wire front entry (Two in-put &

Two out-put) The colour will be decided by

Engineer - in - Charge. (Preferably In Blue,

Red & Grey Colors in the ratio of 1:2:3)

Inspection: Consignee "

39 39 "Supply of End plate 2.5mm/0.091 in thick as Numbers 50.00 8.47 423.50

per site requirement. Inspection: Consignee"

width as per site requirement. Inspection:

41 41 "Supply of Carrier Rails for above 35mm x Metre 12.00 92.37 1108.44

7.5mm, 1mm/0.039 in thickness un-slotted

type as per site requirement. Inspection:

SEALDAH DIVISION-S AND T/EASTERN RLY

42 42 "Casting, concreting and curing of foundation Numbers 27.00 1038.14 28029.78

(1:3:6) and erection of SLB/BSLB/SB/WB/Stop

board as per DRG. NO S&T / C/ 34 (NKG)all

materials required for the work including

cement, rail post etc. to be supplied by the

contractor.This includes supply of

SLB/BSLB/SB/WB/ Stop board as per RDSO

DRG NO. SA-2375 (ADV.) (WITH LATEST

AMDT.) for SLB/BSLB and as per

RDSODRGNO.7235/B(WITHLATESTAMDT.)for

SB/WB/StopBoard. SUPPLY. Inspection:

Consignee Note: Board should be Retro

43 43 "Casting, concreting and curing of foundation Numbers 27.00 4847.46 130881.42

(1:3:6) and erection of SLB/BSLB/SB/WB/Stop

board as per DRG. NO S&T / C / 34 (NKG) all

materials required for the work including

cement, rail post etc. to be supplied by the

contractor.This includes supply of

SLB/BSLB/SB/WB/ Stop board as per RDSO

DRG NO. SA-2375 (ADV.) (WITH LATEST

AMDT.) for SLB/BSLB and as per

RDSODRGNO.7235/B(WITHLATESTAMDT.)for

SB/WB/StopBoard. EXECUTION. Note: Board

should be Retro reflective. "

44 44 "Supply of Yellow Retro reflective sheet for LC Set 30.00 1447.46 43423.80

Boom prismatic grade reflective sheets of

size 305x290mm, one set consist 18 pieces.

Inspection:Consignee."

45 45 Dismantling of existing main signal including Numbers 28.00 1032.20 28901.60

dependent shunt signal, calling on signal if

any, fitted on the same post along with signal

post, signal unit, ci base without damaging

46 46 Dismantling of existing Signal Numbers 27.00 1874.58 50613.66

Foundation(upto ground level by hydraulic

47 47 Supply of colour light Signal Post 4.6 mtrs. Numbers 27.00 13516.95 364957.65

and ladder 4.5 mtrs. With bases for ladder

and post as per RDSO SPEC. NO. IRS-S-6-81

and DRG. NO. SA-23153/ADV/AIT-1. All

drawing should be as per latest. Note: - this

includes signal post, base, ladder, ladder

base, platform, rail guard & blanking off.

Materials to be procured from approved list of

firms for manufacturer & supply of

mechanical signalling items. Inspection :

Consignee subject to procurement from RDSO

approved vendors

48 48 Casting, concreting & curing of foundation for Numbers 27.00 6834.75 184538.25

Main signal including cost of all materials

required for casting and concreting. All

materials required for execution will be

supplied by the contractor including cement,

sand & stone chips as per DRG. NO. S&T/C-

SEALDAH DIVISION-S AND T/EASTERN RLY

49 49 "Installation, erection and wiring of CLS unit, Numbers 1.00 22527.97 22527.97

post, ladder & base LED unit including paying

out of tail cable from location box and

earthing of CLS (LED type). This includes

supply of non - metallic (FRP) colour light

signal housing multi-unit type for Rly.

Signalling suitable for RE Area 2 Aspect

complete without lenses, lamps and signal

transformer as per DRG. NO. SA

23001/A/M(ADV), ALT.8 and as per SPEC. NO.

RDSO/SPN/194/2006 (VER1.0) OR LATEST.

FRP material as RDSO SPEC NO. RDSO/SPN/

151/1997 OR LATEST. All drawings should be

as per latest. Materials to be procured from

RDSO's approved firm only. Note: Signal unit

should be compatible to 'LED' type. Note:

installation, erection & wiring of signalling

unit includes LED signal lighting unit

including current regulator. This also includes

protection of unit from rain water.

Supply.Inspection: Consignee "

50 50 "Installation, erection and wiring of CLS unit, Numbers 1.00 1405.08 1405.08

post, ladder & base LED unit including paying

out of tail cable from location box and

earthing of CLS (LED type). This includes

supply of non - metallic (FRP) colour light

signal housing multi-unit type for Rly.

Signalling suitable for RE Area 2 Aspect

complete without lenses, lamps and signal

transformer as per DRG. NO. SA

23001/A/M(ADV), ALT.8 and as per SPEC. NO.

RDSO/SPN/194/2006 (VER1.0) OR LATEST.

FRP material as RDSO SPEC NO. RDSO/SPN/

151/1997 OR LATEST. All drawings should be

as per latest. Materials to be procured from

RDSO's approved firm only. Note: Signal unit

should be compatible to 'LED' type. Note:

installation, erection & wiring of signalling

unit includes LED signal lighting unit

including current regulator. This also includes

protection of unit from rain water. Execution"

51 51 "Installation, erection and wiring of CLS unit, Numbers 16.00 23143.22 370291.52

post, ladder & base LED unit including paying

out of tail cable from location box and

earthing of CLS (LED type). This includes

supply of non - metallic (FRP) colour light

signal housing multi-unit type for Rly.

Signalling suitable for RE Area 3 Aspect

complete without lenses, lamps and signal

transformer as per DRG. NO. SA

23001/A/M(ADV), ALT.8 and as per SPEC. NO.

RDSO/SPN/194/2006 (VER1.0) OR LATEST.

FRP material as per rdso spec no.

Rdso/spn/151/1997 or LATEST. All drawings

should be as per latest. Materials to be

procured from RDSO's approved firm

only.Note: Signal unit should be compatible

to 'LED' type. Note: installation, erection &

wiring of signalling unit includes led signal

lighting unit including current regulator. This

also includes protection of unit from rain

water. Supply Inspection: Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

52 52 "Installation, erection and wiring of CLS unit, Numbers 16.00 1993.22 31891.52

post, ladder & base LED unit including paying

out of tail cable from location box and

earthing of CLS (LED type). This includes

supply of non - metallic (FRP) colour light

signal housing multi-unit type for Rly.

Signalling suitable for RE Area 3 Aspect

complete without lenses, lamps and signal

transformer as per DRG. NO. SA

23001/A/M(ADV), ALT.8 and as per SPEC. NO.

RDSO/SPN/194/2006 (VER1.0) OR LATEST.

FRP material as per rdso spec no.

Rdso/spn/151/1997 or LATEST. All drawings

should be as per latest. Materials to be

procured from RDSO's approved firm

only.Note: Signal unit should be compatible

to 'LED' type. Note: installation, erection &

wiring of signalling unit includes led signal

lighting unit including current regulator. This

also includes protection of unit from rain

water. Execution "

53 53 Installation, erection and wiring of CLS unit, Numbers 10.00 26087.29 260872.90

post, ladder & base LED unit including paying

out of tail cable from location box and

earthing of CLS (LED type). This includes

supply of non - metallic (FRP) colour light

signal housing multi-unit type for Rly.

Signalling suitable for RE Area 4 Aspect

complete without lenses, lamps and signal

transformer as per DRG. NO. SA

23001/A/M(ADV), ALT.8 and as per SPEC. NO.

RDSO/SPN/194/2006 (VER1.0) OR LATEST.

FRP material as per rdso spec no.

Rdso/spn/151/1997 or LATEST. All drawings

should be as per latest. Materials to be

procured from RDSO's approved firm

only.Note: Signal unit should be compatible

to 'LED' type. Note: installation, erection &

wiring of signalling unit includes led signal

lighting unit including current regulator. This

also includes protection of unit from rain

water.Supply.Inspection: Consignee

54 54 "Installation, erection and wiring of CLS unit, Numbers 10.00 2313.56 23135.60

post, ladder & base LED unit including paying

out of tail cable from location box and

earthing of CLS (LED type). This includes

supply of non - metallic (FRP) colour light

signal housing multi-unit type for Rly.

Signalling suitable for RE Area 4 Aspect

complete without lenses, lamps and signal

transformer as per DRG. NO. SA

23001/A/M(ADV), ALT.8 and as per SPEC. NO.

RDSO/SPN/194/2006 (VER1.0) OR LATEST.

FRP material as per rdso spec no.

Rdso/spn/151/1997 or LATEST. All drawings

should be as per latest. Materials to be

procured from RDSO's approved firm

only.Note: Signal unit should be compatible

to 'LED' type. Note: installation, erection &

wiring of signalling unit includes led signal

lighting unit including current regulator. This

also includes protection of unit from rain

water. Execution "

SEALDAH DIVISION-S AND T/EASTERN RLY

55 55 "Installation, erection and wiring of junction Numbers 11.00 28912.71 318039.81

type route indicator [LED type] this include

supply of non metallic FRP junction type

route indicator for Railway Signalling suitable

for RE Area without lamp. Lenses, signal

transformer as per RDSO SPEC. NO.

RDSO/SPN/194/2006 (VER - 1.0) OR LATEST.

FRP material as per RDSO SPEC. NO.

RDSO/SPN/151/ 1997 OR LATEST. All

drawings should be as per latest. Material to

be procured from RDSO's approved firm only.

Note: Signal unit should be compatible to LED

type. Note: installation, erection & wiring of

signalling unit includes LED signal, lighting

unit including current regulator. This also

includes protection of unit from rain water.

Supply of 1 WAY AS PER RDSO DRG. NO. SA-

23401 (ADV)/ ALT.2 Inspection: Consignee

subject to procurement from RDSO approved

56 56 "Installation, erection and wiring of junction Numbers 11.00 566.95 6236.45

type route indicator [LED type] this include

supply of non metallic FRP junction type

route indicator for Railway Signalling suitable

for RE Area without lamp. Lenses, signal

transformer as per RDSO SPEC. NO.

RDSO/SPN/194/2006 (VER - 1.0) OR LATEST.

FRP material as per RDSO SPEC. NO.

RDSO/SPN/151/ 1997 OR LATEST. All

drawings should be as per latest. Material to

be procured from RDSO's approved firm only.

Note: Signal unit should be compatible to LED

type. Note: installation, erection & wiring of

signalling unit includes LED signal, lighting

unit including current regulator. This also

includes protection of unit from rain water.

Execution of 1 WAY AS PER RDSO DRG. NO.

SA-23401 (ADV)/ ALT.2 "

57 57 "Supply of LED signal lamps for Main Numbers 28.00 7086.44 198420.32

colourlight Signal, 110V AC retrofittable in

existing CLS housing and compatible with AC

LED ECR as per RDSO Specn. No.RDSO/SPN/

199/2010(Rev.1) or latest. Inspection: RDSO

58 58 "Supply of LED signal lamps for Main Numbers 36.00 7107.63 255874.68

colourlight Signal, 110V AC retrofittable in

existing CLS housing and compatible with AC

LED ECR as per RDSO Specn. No.RDSO/SPN/

199/2010(Rev.1) or latest. Inspection: RDSO

59 59 "Supply of LED signal lamps for Main Numbers 28.00 7998.31 223952.68

colourlight Signal, 110V AC retrofittable in

existing CLS housing and compatible with AC

LED ECR as per RDSO Specn. No.RDSO/SPN/

199/2010(Rev.1) or latest. Inspection: RDSO

60 60 "Supply of various LED signals (Subsidiary Numbers 16.00 5788.14 92610.24

Signal), 110V AC retrofittable in existing CLS

housing and compatible with AC LED ECR as

per RDSO Specn. No.RDSO/SPN/153/2011

(Rev.4.1) or latest. Inspection: RDSO LED for

Calling ON Signal Aspect"

61 61 "Supply of position light Shunt signal unit Numbers 36.00 5747.46 206908.56

(without lenses, lamps) with Base Post and

without signal transformer Inspection:

62 62 Casting, concreting and curing of foundation Numbers 31.00 3463.56 107370.36

for Shunt signal including cost of all materials

required for casting and concreting.

SEALDAH DIVISION-S AND T/EASTERN RLY

63 63 Installation, erection and paying out of tail Numbers 36.00 425.42 15315.12

cable from location box and wiring of Shunt

signal, LED unit as per technical specification.

64 64 "Supply of various LED signals - Shunt Signal Numbers 91.00 4809.32 437648.12

Aspect, 110V AC retrofittable in existing CLS

housing and compatible . Inspection: RDSO"

65 65 "Supply of offset bracket for position light Numbers 31.00 1729.66 53619.46

Shunt Signal (90mm outside Dia.) post with U

clamps, nuts, washers complete Inspection:

66 66 "SUPPLY OF MODEM CARD FOR CEL make Numbers 1.00 32600.00 32600.00

SSDAC TYPE AXLE COUNTER AS PER

RDSO/SPN/177/2012 (Ver-3) or latest version

and ammendment upto date if any

Inspection: RDSO"

67 67 "SUPPLY OF SIGNAL CONDITIONER CARD ( Numbers 1.00 32600.00 32600.00

SCC-1 = 50% & SCC-2 = 50%) FOR CEL make

S S D A C TYPE AXLE COUNTER AS PER

RDSO/SPN/ 177/2012 (Ver-3) or latest version

and ammendment upto date if any

Inspection: RDSO"

68 68 "SUPPLY OF RESET BOX FOR CEL make Numbers 1.00 42600.00 42600.00

SSDAC TYPE AXLE COUNTER, MODEL 710P AS

PER RDSO/SPN/177/ 2012 (Ver-3) or latest

version and ammendment upto date if any

Inspection: RDSO"

69 69 "Supply of WEB DETECTORS for CEL make Numbers 1.00 44600.00 44600.00

SSDAC as per RDSO/SPN/177/ 2012 (Ver-3) or

latest version and ammendment upto date if

any ( Each Set consists of 2 Nos TX.2 Nos.

RX) Phase reversal Type Inspection: RDSO."

70 70 "SUPPLY OF 21 KHZ / 25 KHZ TRANSMITTER Numbers 3.00 30611.03 91833.09

COILS ASSEMBLY COMPATIBLE TO

GGTRONICS MAKE SSDAC CONFORMING TO

SPEC. NO. RDSO/SPN/ 177/2012 (VER.3)

AND/OR AS PER SITE REQUIREMENT.

Inspection: RDSO Note :- Length of the Coil

should be 15 Meter."

COILS ASSEMBLY COMPATIBLE TO

GGTRONICS MAKE SSDAC CONFORMING TO

SPEC. NO. RDSO/SPN/177/2012 (VER.3)

AND/OR AS PER SITE REQUIREMENT.

Inspection: RDSO Note :- Length of the Coil

should be 15 Meter."

72 72 "SUPPLY OF CPU-1 CARD COMPATIBLE TO Numbers 3.00 44264.32 132792.96

GGTRONICS MAKE HASSDAC CONFORMING

TO SPEC. NO. RDSO/SPN/ 177/2012 (VER.3)

AND/OR AS PER SITE REQUIREMENT.

Inspection: RDSO "

73 73 "SUPPLY OF CPU-2 CARD COMPATIBLE TO Numbers 3.00 44264.32 132792.96

GGTRONICS MAKE HASSDAC CONFORMING

TO SPEC. NO. RDSO/SPN/ 177/2012 (VER.3)

AND/OR AS PER SITE REQUIREMENT.

Inspection: RDSO "

COMPATIBLE TO GGTRONICS MAKE HASSDAC

CONFORMING TO SPEC. NO.

RDSO/SPN/177/2012 (VER.3) AND/OR AS PER

SITE REQUIREMENT. INSPECTION : RDSO."

COMPATIBLE TO GGTRONICS MAKE HASSDAC

CONFORMING TO SPEC. NO.

RDSO/SPN/177/2012 (VER.3) AND/OR AS PER

SITE REQUIREMENT. INSPECTION : RDSO."

SEALDAH DIVISION-S AND T/EASTERN RLY

76 76 "SUPPLY OF COMMUNICATION (COM-1/2) Numbers 2.00 16556.31 33112.62

CARD COMPATIBLE TO GGTRONICS MAKE

HASSDAC CONFORMING TO SPEC. NO.

RDSO/SPN/177/2012 (VER.3) AND/OR AS PER

SITE REQUIREMENT. INSPECTION : RDSO."

77 77 "SUPPLY OF COMMUNICATION (COM-1) CARD Numbers 1.00 16556.31 16556.31

COMPATIBLE TO GGTRONICS MAKE HASSDAC

CONFORMING TO SPEC. NO.

RDSO/SPN/177/2012 (VER.3) AND/OR AS PER

SITE REQUIREMENT. INSPECTION : RDSO."

78 78 "SUPPLY OF COMMUNICATION (COM-2) CARD Numbers 1.00 16556.31 16556.31

COMPATIBLE TO GGTRONICS MAKE HASSDAC

CONFORMING TO SPEC. NO.

RDSO/SPN/177/2012 (VER.3) AND/OR AS PER

SITE REQUIREMENT. INSPECTION : RDSO."

79 79 "SUPPLY OF RELAY DRIVE (RD-1/2) CARD Numbers 1.00 17074.03 17074.03

COMPATIBLE TO GGTRONICS MAKE HASSDAC

CONFORMING TO SPEC. NO.

RDSO/SPN/177/2012 (VER.3) AND/OR AS PER

SITE REQUIREMENT. INSPECTION : RDSO."

80 80 "SUPPLY OF RELAY DRIVE (RD-1) CARD Numbers 1.00 17074.03 17074.03

COMPATIBLE TO GGTRONICS MAKE HASSDAC

CONFORMING TO SPEC. NO.

RDSO/SPN/177/2012 (VER.3) AND/OR AS PER

SITE REQUIREMENT. INSPECTION : RDSO."

81 81 "SUPPLY OF RELAY DRIVE (RD-2) CARD Numbers 1.00 17074.03 17074.03

COMPATIBLE TO GGTRONICS MAKE HASSDAC

CONFORMING TO SPEC. NO.

RDSO/SPN/177/2012 (VER.3) AND/OR AS PER

SITE REQUIREMENT. INSPECTION : RDSO."

COMPATIBLE TO GGTRONICS MAKE HASSDAC

CONFORMING TO SPEC. NO.

RDSO/SPN/177/2012 (VER.3) AND/OR AS PER

SITE REQUIREMENT. INSPECTION : RDSO."

83 83 "Supply of Output card compapible to work Numbers 2.00 24800.00 49600.00

with existing Deltron make UFSBI as per

specification no. S-105/2012 Ver 0 or latest .

Make- Deltron Inspection: RDSO"

84 84 "Supply of Input card compapible to work Numbers 2.00 11660.00 23320.00

with existing Deltron make UFSBI as per

specification no. S-105/2012 Ver 0 or latest .

Make- Deltron Inspection: RDSO"

85 85 "Supply of CPU card compapible to work with Numbers 2.00 26500.00 53000.00

existing Deltron make UFSBI as per

specification no. S-105/2012 Ver 0 or latest .

Make- Deltron Inspection: RDSO"

86 86 "Supply of Modem card compapible to work Numbers 2.00 56000.00 112000.00

with existing Deltron make UFSBI as per

specification no. S-105/2012 Ver 0 or latest .

Make- Deltron Inspection: RDSO"

87 87 "Supply of CCC Card compapible to work with Numbers 2.00 22250.00 44500.00

existing Deltron make UFSBI as per

specification no. S-105/2012 Ver 0 or latest .

Make- Deltron Inspection: RDSO"

88 88 "Supply of Mother Board compapible to work Numbers 2.00 34800.00 69600.00

with existing Deltron make U F S B I . Make-

Deltron Inspection: RDSO"

89 89 "Supply of Reset Box compapible to work with Numbers 2.00 11050.00 22100.00

existing Deltron make UFSBI as per

specification no. S-105/2012 Ver 0 or latest .

Make- Deltron Inspection: RDSO"

90 90 "Supply of DC-DC Converter (Hot Stand by Numbers 2.00 37300.00 74600.00

type) Card compapible to work with existing

Deltron make UFSBI as per specification no.

S-105/2012 Ver 0 or latest . Make- Deltron

Inspection: RDSO"

SEALDAH DIVISION-S AND T/EASTERN RLY

91 91 "Supply of System Card (Webfil Make) as per Numbers 2.00 14208.00 28416.00

IRS: S-104/2012 ver- 0 or latest Inspection

92 92 "Supply of Communication Card( Webfil Numbers 2.00 15469.00 30938.00

Make)as per IRS: S-104/2012 ver- 0 or latest

Inspection :RDSO"

93 93 "Supply of Input Card( Webfil Make)as per Numbers 2.00 8512.00 17024.00

IRS: S-104/2012 ver- 0 or latest Inspection

94 94 "Supply of Output Card ( Webfil Make)as per Numbers 2.00 15998.00 31996.00

IRS: S-104/2012 ver- 0 or latest Inspection

95 95 "Supply of PSU Card (Webfil Make)as per IRS: Numbers 2.00 14850.00 29700.00

S-104/2012 ver- 0 or latest Inspection :RDSO"

96 96 "Supply of Display Card with Reset Box ( Numbers 1.00 13101.00 13101.00

Webfil Make)as per IRS: S-104/2012 ver- 0 or

latest Inspection :RDSO"

97 97 "Supply of Back plane( Webfil Make)as per Numbers 1.00 23659.00 23659.00

IRS: S-104/2012 ver- 0 or latest Inspection

98 98 "Supply of Alarm Extender Card ( Webfil Numbers 1.00 21226.00 21226.00

Make)as per IRS: S-104/2012 ver- 0 or latest

Inspection :RDSO"

99 99 "Supply of Automatic Media Change over Numbers 2.00 20756.00 41512.00

unit( Webfil Make)as per IRS: S-104/2012 ver-

0 or latest Inspection :RDSO"

100 100 "Supply of Auto Reset Unit ( Webfil Make)as Numbers 1.00 5439.00 5439.00

per IRS: S-104/2012 ver- 0 or latest

Inspection :RDSO"

101 101 "Supply of ASM's Alarm Panel( Webfil Make)as Numbers 2.00 31835.00 63670.00

per IRS: S-104/2012 ver- 0 or latest

Inspection :RDSO"

102 102 "Supply of SM's Block Panel( Webfil Make)as Numbers 2.00 14208.00 28416.00

per IRS: S-104/2012 ver- 0 or latest

Inspection :RDSO"

103 103 "Supply of 1 x 6 Sq.mm. (Green) multi strand Metre 1217.00 35.59 43313.03

copper power wire as per IS: 694:2010 or

latest, 84 conductor each dia 0.30mm +/-

0.01 with insulation thickness of 0.8 mm and

nominal conductor resistance of 3.3 ohms/km

and test parameters as per RDSO

Specn.No.IRS:S-76/89(Amnd.3) or latest.

Color of the wire which is required will be

specified by the Engineer in-charge.

Inspection :Consignee "

104 104 "Supply of Digital Multimeter of Rishabh 6016 Numbers 14.00 19689.00 275646.00

Advanced Multimeter or Similar/ superior,

True RMS as per Technical Spec. -TS-1.

Inspection : Consignee . The Functionality

test of the Multimeter has to be checked by

105 105 "Supply of Hand Held True RMS smart Numbers 11.00 25307.00 278377.00

leakage Clamp Meter of Rishav ALCT-60A or

Similar/ sipirior as per Technical Spec. -TS-2.

Inspection : Consignee. The Functionality test

of the Multimeter has to be checked by

106 106 "Supply of electronic Cable route Numbers 5.00 348066.10 1740330.50

tracer/locator with underground cable and

pipe locating receiver that provide location of

armored OFC, signalling and telecom, power

cable etc. make : Stanley/3M Dynatel, Model :

STLOC10/ 2273M-iD-UU3W- RT or superior.

Item to be supplied after successful

demonstration and Approval of Railway.

Inspection : Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

107 107 "Excavation of cable trench as per cable cum 9720.00 207.63 2018163.60

route plan, 1.2 Mtr. deep and of 0.3 Mtr. to

0.6 Mtr. wide at bottom without brick as per

DRG. NO. S&T/C-40(NKG), SK/4/95/NKG,

SK/8/95/NKG. or latest alongside the track in

all kinds of soil, conforming to distances as

per cable route plan and refilling. This work

includes clearing of route from bushes etc.

The work shall be done as per the extant

practice on Eastern Railway and instructions

of Railway Engineer at site. Note:-(a) for all

trenches from distant signal to home signal

and to relay room, the minimum headway

above the uppermost cable in the trench

should be 600mm. If due to a large no. Of

cables headway is not available, 4"" of 1:2:4

concreting should be done. Note:-(b-1)

payment will be made as per actual work

done on pro-rata basis, if required depth is

not available at site. (b-2) if the depth of

trench is not uniform in a span of 100 mtr. or

shorter lengths if site condition demands

along the cable run, minimum depth will be

taken for that particular stretch for payment

Note : (c ) All kinds of soils means including

ballast mixed soil of Railway Track. "

108 108 Digging of trench 1.2 Mtrs. deep from rail cum 36.00 235.59 8481.24

flange/ road level and 0.3 Mtrs to 0.6 Mtrs

wide and back filling after placing of DWC/

RCC/GI pipe. (Placing of DWC/RCC/GI pipe

covered separately). The ballast disturbed be

screened and dressed as required by

Engineer-in-charge or his representatives and

road tarred immediately. For track crossing,

RDSO sketch No. SDO/CABLE LAYING/009 or

latest and for Road Crossing, RDSO sketch

No. SDO/CABLE LAYING/010 or latest are to

109 109 "Cement concrete work for miscellaneous cum 850.00 3047.46 2590341.00

items in the ratio 1: 3: 6. Item includes

excavation, ramming, curing and plastering

with cement & sand mixture (aggregate not

exceeding 3.8 cm.) (Aggregate cement &

sand to be supplied by the contractor).

Wherever depth of 0.5 m cable trench is not

feasible, cable shall be protected as :-

Preparation of cement mixture 1:3:6 with

contractor's own materials and spreading

cement concrete mixture layer of 100 mm

thick over the already laid cables in the

excavated trench. "

110 110 "Laying of S&T Cables of various cores/ pairs/ Route Kilo 15.70 4240.00 66568.00

quads in trenches/ GI pipes/ RCC pipes/ DWC Meter

pipes/ Trunking. This also includes laying of (RKM)

cables in track crossings & road crossings.

Item includes provision of labels of coloured

plastic adhesive tapes or any other

identifiable material on each cable to give the

cable number at each Gantry

Post/hectometre post. (Cables will be

meggered before and after its laying by

contractor under supervision of Railway

Representative and he will submit the

meggering report of each testing). Length of

the cable laid includes the length of the cable

coiled for termination purposes. Note : Cable

will be supplied by Rly."

SEALDAH DIVISION-S AND T/EASTERN RLY

111 111 "Supply of Double Wall Corrugated (DWC)- Metre 500.00 336.44 168220.00

HDPE pipe/duct of size 200 mm outer dia, &

175 mm inner dia. It includes supply of

Double Wall Corrugated -HDPE pipe/duct as

per RDSO Specn.No. RDSO/SPN/ 204/2011

(version 1.1) or latest and conforming to ISI

Spec. No.IS:14930, Part-II. (The

manufacturers, suppliers must produce valid

IS license and should be certified under ISO

9000 and shall submit copy of certificate).

One of the following coupling arrangements

should also be supplied with each pipe as per

the site requirement.1) Suitable snap fit

coupler with rubber O-Ring 2) Spacers3)

Tees4) Bend,5) End-capDWC pipe shall be

marked at every 1 mtr length in such a way

that manufacturer's name, vendor name and

year of manufacture can be easily identified.

Inspection : Consignee"

112 112 Placing of DWC/HDPE/RCC/GI pipes along with Metre 600.00 26.27 15762.00

collars in trenches at places near track and

road, crossings, platform cuttings etc.

113 113 "Termination of Outdoor Cables (Main Cables Per 9384.00 7.63 71599.92

/tail cables) at both ends in location boxes, Conductor

cable termination rack in relay room, station

building, generator room etc. The item

includes dressing of cables and wires with

dressing threads as per standard practice. All

material required for this item will be

supplied by contractor. The outdoor cable

shall be terminated in Relay Room, DG Room,

ASM Room etc. under supervision and

instructions issued by Engr. In-charge of the

work. Inspection: Consignee"

114 114 "Supply of Siding Point Control , Electrical Set 27.00 24624.58 664863.66

detector etc. as per IRS Spec. Electrical

detector should be as per IRS S 49-74.

Complete material for the above work will be

supplied by the contractor. (Trap Indicator if

required shall be provided by Contactor)

Inspection: Consignee"

115 115 "Portable powerfull 50 LED for high lumen Numbers 3.00 12426.73 37280.19

output light, with lithium ion battery of

4400mAH Specification :- Light Source- LED,

Total Lumens-2 000 LUMENS or more, LED

Type- 50 LED SMD type, light

dispwersion/focussing- integratewd lens with

octagonal type lens, Lens type- PC/PP Lens

with Octagonal arrangrment. Battery type-

BIS certified powerful Lithium ION battery

(Lasting Continuous glowing 4-5 hrs( high

Mode) 12V DC SYSTEM, 4400mAH. Provided

with electric charger. Ingress protection -

IP54, Mounting Hook- side + buttom,

Movement when on Tripod- 360° in Horizontal

plane and 90° in vertical plane, Opt.

Temparature Range- 0°C to 55°C , Weight-

500gm. Warranty - 3 Years , Make/Brand - OM

ENERGY SAVERS OR SIMILAR. Item to be

supplied after successful demonstration and

Approval of Railway. Inspection : Consignee "

SEALDAH DIVISION-S AND T/EASTERN RLY

116 116 "Portable rechargeable 50 Watt LED flood Numbers 1.00 114542.01 114542.01

lighting system with 360 degree lighting

module. Specification Light Power - 50 Watt

LED chip of reputed make like

Edusion/CREE/EPISTAR or similar,5000

LUMENS, Light Spectrum colour- White :

6000° to 7000° kelvin, Radition angle- 360° in

Horizontal plane, System Volt- 12V/24V, Back

up time- High mode (50Watt) -7-8 Hrs when

fully charged. Battery type- BIS certified

powerful Lithium ION battery/ Lithium

polymer with metal protective casing for

safety, Solar charging compatibility -Yes,

System operation- Panel control, System

protection class - IP65, Opt. Temp. - 0 to 55

Degree Celcious Warranty - 3 Years

,Make/Brand - MIDAS Safety, ASKA and

Pelican Or similar. Item to be supplied after

successful demonstration and Approval of

Railway. Inspection : Consignee"

117 117 "Multi positioning portable maintenance lamp Numbers 2.00 43007.28 86014.56

with dual mounting system (Powerfull

magnetic plus normal base for floor

operation) Specification :- Light Source- SMD

LED, Light Power - 36 Watt,4000 LUMENS,

LED Type- SMD LED CLUSTER, Light Spectrum

colour- White : 6000° K appx., Radition angle-

>90°, Battery type- BIS certified powerful

Lithium ION battery (Lasting Continuous

glowing 7-8 hrs(High Mode) 24V SYSTEM,

14000mAH. Provided with electric charger.

Ingress protection - IP65, Warranty -3 Years ,

Model- OESPLEDFL36W8HMAGMA

Make/Brand - OM ENERGY SAVERS OR

SIMILAR. Item to be supplied after successful

demonstration and Approval of Railway.

Inspection : Consignee"

118 118 "Supply of PVC insulated multi strand, single Kilometre 1.50 6499.15 9748.72

corecopper conductor of size 16/0.2 mm

(0.5sqmm) as per IS 694:2010 and RDSO

Specn. No. IRS: S-76/89 (Amnd-3) or latest.

Each coil should be of100/200/500 meters

length. Color of the wire which is required will

be specified by the Engineer in charge

.Inspection:Consignee subject to procurement

from RDSO approved vendors"

119 119 "Cleaning of Railway premises like throughly Numbers 28.00 408.46 11436.88

clear of Garbage near by Railway Track,

cutting of Small Bushes /Grass at near by

area of Location Box, Signal Post, LC Gate &

inside Store Room , Power Room, Battery

Room , Railway Offices as per instruction of

Railway site Supervisors. Note :- ""NO' in Unit

column means One Person per day,"

SEALDAH DIVISION-S AND T/EASTERN RLY

120 120 "RELAY WIRING IN RELAY ROOM / GATE Numbers 2000.00 388.00 776000.00

LODGE, ETC., INCLUDING FIXING OF RELAY

BASE IN RELAY RACK, RELAY RACK TO RELAY

RACK & CTR WIRING, WIRING OF

CONDENSOR & RESISTANCE, ETC. ALL

MWIRES AND HARDWARES REQUIRED FOR

RELAY WIRING WILL BE SUPPLIED BY THE

CONTRACTOR EXCEPT PLUG-IN TYPE RELAY

WITH BASE, FUSE, FUSE BASE, ARA/WAGO

TERMINAL. CONDENSER & RESISTANCE (IF

REQUIRED) WILL BE SUPPLIED BY THE RLY.

WIRING ALONG WITH LETTERING , DRESSING,

BUNCHING WILL BE DONE AS PER RAILWAY

PRACTICE AND INSTRUCTION OF RLY. SITE

ENGINEER. WIRE FOR RELAY WIRING SHOULD

BE PROCURED FROM RDSO APPROVED FIRM

ONLY. INSPECTION : CONSIGNEE"

121 121 Designing and Plotting of Signalling Per SIP 4.00 23789.83 95159.32

Interlocking Plan(SIP) in AUTOCAD.Two copies

of prints with soft copy will be submitted to

Railway for checking. If alterations are

suggested/proposed by Railways then again

two copies of prints will be submitted for

advance approval after carrying out all the

alterations as suggested/proposed by the

Railways. Tracings will be submitted for all

the diagrams mentioned above for the

purpose of approval by Railway prior to

commissioning of station.

122 122 "Installation, wiring, testing & commissioning Per Track 93.00 2837.29 263867.97

of track circuit involving points & crossings as Circuit

per track circuiting plan, track battery

charging and installation including drilling

9/32"" hole on rails; fixing of bonding(double)

with 8 SWG soft GI wire, insulation of

stretcher bars (leading & following), gauge /

crossing tie plates involving cutting and

riveting/welding of angle clit, split stretcher

bars, fixing of track lead junction box, rail

connector with GI wire, track jumpering

(double) with supporting arrangement for

holding termination of track lead wires,

including series jumpers, jumper

wireterminals, track feed set(track chargers,

resistance, fuses, battery etc.) As per

approved IYD for point zonetrack circuit.

Note: -Battery charging solution to be

supplied by the contractor & double

jumpering to be provided. "

123 123 "Supply, Transportation, Installation, Testing Per 13.00 290303.39 3773944.07

and Commissioning of Multi Section Digital Detection

Axle Counter (MSDAC) for mentioned Point (DP)

detection Point by the purchaser & Track

Section as per SIP uploaded with the tender,

complete with all accessories, cable required

with each track device & Card viz., Axle

Detectors, Track Side Electronics/DAC field

units, Central Evaluator (Central Evaluator

unit should be housed in a pre-fabricated

Rack to be supplied along with the system),

Reset unit, Relay unit, Event logger &

Diagnostic terminals etc. required for

different Detection Points & Track Sections as

per RDSO Specification No.

RDSO/SPN/176/2013, Ver.3 or latest as per

Annexure-A, B & C. Inspection :RDSO "

SEALDAH DIVISION-S AND T/EASTERN RLY

124 124 "Supply of full size apparatus case (Large) (as Numbers 20.00 11793.22 235864.40

per DRAWING NO. SW SK NO. 4/90 & other

applicable GKP SW Drawing). This includes

supply of location box (GKP type) with 'E'

type lock & key, fitted on location door on

both side, E Type lock (ward No. w i l l be

specified by Engineer-in Charge) as per RDSO

Drg. No. SA 3376 and Key to Drg. No. 3377 as

per RDSO drawing No. RDSO/S-11500.

Inspection : Consignee subject to

procurement from RECOMMENDED LIST OF

FIRMS FOR MECHANICAL SIGNALLING ITEMS

(SS Location Box Preferable) Inspection

125 125 "Supply of hard wood shelves thickness 25 Numbers 20.00 477.12 9542.40

mm for keeping equipment's and batteries in

the location box (FULL or HALF GKP /other

type) with suitable varnish and anti-termite

chemicals fitted on angles with nuts & bolts.

950 x 400 x 25 MM for full size location box .

Inspection:- Consignee "

126 126 "Casting, concreting and curing of concrete Numbers 20.00 2993.22 59864.40

foundation ((in ratio 1:3:6), erection and

installation of Full size Apparatus Case (GKP

type)/Stainless Steel (SS) Apparatus Case as

per DRG.NO. S&T/C-6/98(NKG) with 'E' type

lock on CC foundation. This includes cost of

all materials required for fixing holding down

bolts, casting, concreting. Note: - bolts, nuts

and washers, bitumen compound to be

supplied by contractor and bitumen

compound to be used in between apparatus

case and foundation as per site engineer.

This also includes bottom of apparatus cases

filled with sand and the outside covered with

masonry work and neat cement plastering.

Note: - i) Location boxes to painted with anti-

corrosive paints as per IS:- 9862-1981, one

and half feet from the bottom, on all surfaces-

both inside and outside. ii) Location box will

be supplied by Rly."

127 127 "Fixing by slotted angle, wiring of terminal Numbers 20.00 4093.22 81864.40

strips, hylam strip, relays, fuses with base,

fixing of hard wood shelves for Full size

Apparatus Case with termination & Earthing

of cables and wiring with lettering as required

including supply of slotted angles, wires,

ferrules for marking and miscellaneous

materials per location to be supplied by

contractor. (all materials except relay,

terminal strips, Bakelite strip, fuses with base

and hard wood shelves to be supplied by the

contractor). Wires to be used for this purpose

should be procured from RDSO'S approved

firm and to be inspected by RDSO. [Quantity

of wires to be specified by contractor]. NB-

power cable to be terminated with proper

lugs and required buss bar and other

terminals to be supplied by the contractor.

Inspection : Consignee"

128 128 "Supply of paper base hylam sheet 12 mm Sqm 5.00 4550.85 22754.25

thick. Inspection: consignee."

129 129 "Supply of PBT ARA terminal, 6 WAY, DRG. Numbers 200.00 411.02 82204.00

No. 23756, ALT-3. as per IRS Spec. No. IRS: S-

75-2006(REV-2) or Latest. Material to be

procured from RDSO's approved firm only.

Inspection: RDSO. "

SEALDAH DIVISION-S AND T/EASTERN RLY

130 130 "Supply of fuse block (PBT) to spec.no.IRS-S- Numbers 50.00 150.85 7542.50

75/2006(REV-2) OR LATEST,DRG.NO.SA-

23748 with fuse inserts cartridge, non-

deteriorating type to spec.IRS-S-78/92 with

latest amendment, to be mounted inside the

location box on hylum sheet. Fuse Base

Inspection: -RDSO."

131 131 "Supply of fuse block (PBT) to spec.no.IRS-S- Numbers 200.00 51.69 10338.00

75/2006(REV-2) OR LATEST,DRG.NO.SA-

23748 with fuse inserts cartridge, non-

deteriorating type to spec.IRS-S-78/92 with

latest amendment, to be mounted inside the

location box on hylum sheet. Fuse, non-

deteriorating(2A/6A/10A/16A) type,

cylindrical(IRS-S-78/92) Inspection: -RDSO."

132 132 "Supply of Earth electrode mild steel Numbers 20.00 1267.80 25356.00

galvanized, light class, IS:1239(PART-I)-

1979.earth electrode pipe should be with 3

mm thick, 50 mm dia and

perforated(staggered),5 mm dia holes, 2 nos

per 305 mm length. Earth pipe should include

CI threaded cap. Materials to be procured and

designed as per PCSTE/ER's Drg No. SI/TYP/

0097 dated 25.03.25 or latest Inspection:

133 133 "Supply of MS FLAT (SPEC. NO. 226 STD or Numbers 20.00 772.03 15440.60

latest) of size 35 mm x 6 mm. To supplied in

length of minimum 5 mtr or more as per

PCSTE/ER's Drg No. SI/TYP/ 0097 dated

25.03.25 or latest Inspection: Consignee."

134 134 Fixing of earth electrode including laying and Numbers 20.00 983.90 19678.00

installation of MS flat of size 35 mm x 6 mm

with length 5 mtr or as per extant practice of

Eastern Railway. As per PCSTE/ER'S DRG. NO.

SI/TYP/0097 dated 25.03.2025 or latest. for

apparatus cases, signal post & other

equipment as per instruction of site engineer.

Provision for fixing MS flat at apparatus

cases/ signal post/other equipment should be

made by the firm at site. Where required

necessary holes to be drilled on the MS Flat .

Full threaded bolts of 10 mm dia and length

40 mm should be welded in the apparatus

cases in such way that the MS flat at

apparatus case end can be fixed from outside

or from inside (bolts of 10 mm dia and length

40 mm should be supplied by the contructor).

Welding arrangement with accessories and

welding materials should be arranged by the

contractor for fixing of bolts at equipment

end where required as per instruction of site

engineer. All hardware and other

miscellaneous materials required for

installation to be supplied by the contractor

except earth electrodes and MS flat. Sig.

Cable as provided by Railway is also to be

laid and terminated on Earth Electrode and to

GI Wire/GI Flat in Location Box.

135 135 "Supply of cement concrete enclosure for Numbers 20.00 483.90 9678.00

earth electrodes as per Drg No. S&T/C-

36(NKG) & PCSTE/ER's Drg No. SI/TYP/ 0097

dated 25.03.25 or latest. Inspection:

136 136 "Supply of Dual Tone Bell /Buzzer with Set 20.00 4590.68 91813.60

Flasher arrangement and 20 Watt horn

working on 24 V DC/ 110 V AC for warning

road users at LC gates. Inspection:

SEALDAH DIVISION-S AND T/EASTERN RLY

137 137 "Supply of Track feed Battery Charger as per Numbers 100.00 4147.46 414746.00

RDSO Specn. No.IRS: S-89/2013 Ver.1.0 or

latest. Charging Capacity Rating 10 Amps for

Charging 80 AH Battery. Inspection: RDSO"

138 138 "Supply of Adjustable Track Feed Resistance Numbers 100.00 144.92 14492.00

30 Ohms (Disc Type) as per RDSO Drg.

No.SA-20161-66/M or latest. Inspection:

139 139 "Installation wiring, testing and Per Track 57.00 2749.15 156701.55

commissioning of single rail dc track circuit Circuit

(SHORT LENGTH TRACK CIRCUIT UPTO 200

MTS.) as per approved track circuiting plan.

The work includes track battery charging and

installation, fixing of track bonding (double)

with 8 SWG soft GI wire, laying of tail cables

with track lead junction box, rail connector

with galvanised iron wire, track

jumpering(double) with supporting

arrangement for holding as per track circuit

plan. It also includes installation and wiring of

track feed chargers, track relays, track circuit

equipment's in the location box including

fuses and ARA terminals required for the

purpose as per DRG NO. SK/10/95(NKG)

including drilling of 9/32"" hole on rails where

required. Fixing of track lead junction boxes.

Note: - battery charging solution to be

supplied by the contractor & double

jumpering to be provided. Track feed charger

failure alarm with indication panel to be

provided including supply of required

materials. Inspection: Consignee"

140 140 "Supply, Fabrication and Fixing of Retro Numbers 100.00 316.10 31610.00

reflective Nomenclature Board of size 254

mm x 358 mm made of 2mm thick aluminium

sheet & high intensity prismatic (hip) grade

retro reflective sheet (TYPE -IV) including

fixing arrangement for fixing them on

existing post per DRG. NO. S&T/SDAH/SK-

1386 and as per standard practice.

Inspection: Consignee subject to procurement

from RDSO approved vendors Inspection :

141 141 "Supply and installation of P/ C / G/ A/ AG Numbers 100.00 466.10 46610.00

marker (size 250mm dia circle) high intensity

prismatic(TYPE-IV) retro reflective sheet over

2 mm thick aluminium sheet & letter will be

screen printing (250 mm dia circle) as per

drg. S&T/SDAH/SK-1383 and technical

specification attached. This will include cost

of all materials including fixing clamp

required for this work. Inspection: -

142 142 "Alteration/modification in the existing Numbers 50.00 2357.63 117881.50

location boxes (full size), fixing of

equipment's, cable insertion, termination,

wiring, testing & commissioning, two coat

painting, lettering to suit the circuits as per

approved wiring diagrams. This includes

filling with sand and plastering the same.

Note : All the materials like Sand ,Cement

etc. will be supplied for net cementing by the

143 143 "Supply of Power contractor/Relay for motor Numbers 10.00 1740.68 17406.80

24V DC, MAKE L&T MLO/SIEMENS. The

material will be as per RDSO Specn. No.

RDSO/SPN/208/2012/Ver.2.0 and Amendment

1 or latest. Inspection: Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

90W/1500RPM.The material will be as per

RDSO/SPN/208/2012/Ver.2.0 and Amendment

1 or latest. Inspection: Consignee"

145 145 "Supply of Boom lock PMDC MOTOR 24V DC, Numbers 10.00 2094.92 20949.20

40W/1500RPM.The material will be as per

RDSO/SPN/208/2012/Ver.2.0 and Amendment

1 or latest. Inspection: Consignee"

146 146 "Supply of TIMING BELT. The material will be Numbers 10.00 847.46 8474.60

as per RDSO Specn. No.

RDSO/SPN/208/2012/Ver.2.0 and Amendment

1 or latest. Inspection: Consignee"

147 147 "Supply of PUSH BUTTON with ELEMENTS. Set 10.00 337.29 3372.90

The material will be as per RDSO Specn. No.

RDSO/SPN/208/2012/Ver.2.0 and Amendment

1 or latest. Inspection: Consignee"

148 148 FRP LINING AS WELL AS COATING OF Numbers 20.00 6305.80 126116.00

EXISTING ELECTRIC POINT MACHINE TOP

COVER WITH TWO SIDES. THIS LINING DONE

AFTER SCRAPING OF RUST AND CLEANING OF

DUST. THIS INCLUDES COST TWO COATS OF

PAINTING ON THE FRP LINGING

AREA.COLOURS OF THE POINT MACHINE AS

PER IRSEM. Note: 1) FRP Materials will be

supplied by the Contractor. 2) Contractor has

to supply approved quality of Paint like -

Asian / Berger / Shalimar.

149 149 "Supply of Self Regulating type Battery Numbers 10.00 103683.30 1036833.00

charger 230V AC/110V DC 50 Amp as per

RDSO Specn No.IRS :S- 86/2000 (amnd.-4) or

latest Inspection : RDSO"

150 150 "Supply of 0-100 Ohm Single Range Analog Numbers 2.00 7088.00 14176.00

Earth Tester.Metal Body Specification :- Type-

Hand Driven Generator Type, Display -

Analogue, Generator Rotation Speed-

160RPM, Resistance Range (Ohm) : 0-100

Ohm, Terminal - Four. Make- WACO , Rishabh,

Fluke or superior, Warranty - 1 Year.

Inspection : Consignee"

151 151 "Supply of Repro Sheed fed AO+ Wide Numbers 1.00 423644.07 423644.07

Format Scanner.Specification :- Scanner

Type- Sheet Fed, Document Size- AO+,

Document Thikness- 2mm, Scanning Feature-

Simplex, Hard Disk Drive-500 GB, Optd.

Temparature Range- 5-40 Degree C,

Dimension 1150 X381X152(WXDXH)

Inspection : consignee"

152 152 "Carrying out relay alteration to the existing Per Relay 1500.00 228.81 343215.00

relay wiring at relay rack/ location box as per

the approved circuit diagram. These works

include the releasing of existing unused wires

and wiring the relays using 16/0.2 mm copper

wire as per RDSO Spec. Wire to be procured

from RDSO's approved source and inspection:

by RITES [for value of material above Rs.5.0

lakhs.]. Inspection by consignee [for value of

material below than Rs 5.0 lakh]. Note: - wire

to be procured from RDSO's approved source

only. All required material like wire, soldering

material, paint etc. To be supplied by the

contractor for execution of the work."

153 153 "Supply of Top Plate with buttons as per Numbers 60.00 205.93 12355.80

requirement of Domino type of control panel

suitable for domino size 54 x 34 mm.

Inspection: Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

154 154 "Supply of Tools Kit for High frequency Digital Set 4.00 96033.05 384132.20

Axle Counter Multi section. This includes

Supply of Service test panel including meter

for test of track equipment, tools for

mounting and adjustment of track equipment

and standard jig for drilling holes in rail. It

should be as per Principal manufacturers

(OEM) recommended list adequate for

installation, day to day maintenance, and

adjustment of indoor and outdoor gears. This

shall also include kit for making and drilling of

holes on rail. Note: (1) this also includes

supply of cross talk measuring set as per

RDSO SPEC. TC 45-88 or latest, dB meter for

measuring attenuation loss & 500v insulation

tester,dummy wheel, torque wrench (2)

multimeter should be pure sine wave digital

multimeter make Fluke Model 287/ Rishabh

Model 28s. Each measuring tools &

equipment to be supplied with OEM'S test

certificate/ guarantee certificate as per the

reqirement of Site engineer (Make as

applicable ). Inspection: Consignee"

155 155 "Charging of lead acid cell (Secondary cell) of Numbers 55.00 836.44 46004.20

2V 300 capacities as per

Manufacturer's/Railway engineer's

instruction. Acid and distilled water to be

supplied by the contractor. Specific gravity

acid should be approved type duly inspected

by consignee. This includes installation and

commissioning of battery in circuit. Battery to

be kept on wooden rack. Inspection:

156 156 "Supply of Digital Cable Insulation Tester for Numbers 2.00 7366.10 14732.20

measurement of cable insulation resistance

with auto range 0-500 V DC. Rishab, MECO or

from any reputed make. Item to be supplied

after successful demonstration and Approval

of Railway. Inspection: Consignee"

157 157 "Supply of 1 x 10Sq.mm. (Green) multi strand Metre 250.00 100.85 25212.50

copper power wire as per IS: 694:2010 or

latest, 140 conductor each dia 0.30mm +/-

0.01 with insulation thickness of 1.0 mm and

nominal conductor resistance of 1.91

ohms/km and test parameters as per RDSO

Specn.No.IRS:S- 76/89 (Amnd.3) or latest.

Color of the wire which is required will be

specified by the Engineer in-charge

Inspection: Consignee"

multi strand copper power wire as per

IS:694:2010 or latest, 126 conductor each dia

0.40mm +/- 0.01 with insulation thickness of

1.0 mm and nominal conductor resistance of

1.21 ohms/km and test parameters as per

RDSO Specn.No.IRS:S-76/89(Amnd.3) or

latest.Colour of the wire which is required will

be specified by the Engineer incharge.

Inspection: Consignee"

159 159 "Supply of Q-Series Line Relay (QNA1 Type), Numbers 100.00 3395.76 339576.00

AC immunized, 12F/4B,24 V DC along with

plug board (base plate), connectors,retaining

clips etc. and conforming to BRS-931A and

RDSO Specn. No. IRS : S- 34, S - 23 and S -60

with amdt. upto date asapplicable or latest.

The interlocking code for this unit shall be

""ABDFH"". Inspection : RDSO"

SEALDAH DIVISION-S AND T/EASTERN RLY

160 160 "Supply of Q-Series Magnetically Latched Numbers 20.00 4845.76 96915.20

Neutral Line Relay (QL1 Type), 11F/4B,24V

DC complete with plug board (base plate),

connectors and retaining clips and

conforming to BRS-935A and RDSO

Specn.No.IRS: S-34 & S-23with Amdt. upto

date as applicable or latest. The interlocking

code for this unit shall be ""ABDEG"".

Inspection - RDSO"

161 161 "Supply of Q-Series LED ECR (Universal Type Numbers 48.00 4162.71 199810.08

i.e. QECX-61), 4F/4B complete with plug

board (base plate), connectors, retaining clips

etc. and conforming to BRS:941A

STS/E/RELAYS/AC LIT LED SIGNAL/09-2002,

Amdt. -1 and RDSO Specn.No.IRS:S-34 & S-23

with Amdt. upto date as applicable or latest.

The interlocking code for this unit shall be

""ABDHK"". Inspection : RDSO"

162 162 "Supply of Fail safe electronic Flasher device Numbers 30.00 4440.68 133220.40

as per RDSO Specn.No.RDSO/SPN/ 173 / 2002

Amdt.2 or latest. Inspection : RDSO"

163 163 "Supply of Monitoring device for diagnostic Numbers 1.00 134564.00 134564.00

purpose as per Specification : Processor Make

: Intel Processor Generation 13,Number of

Cores per Processor : 16, Processor

Description : Intel Core i7, Processor Number

: Intel Core i7 13700, Operating System

(Factory Pre-Loaded) :Windows 11

Professional, RAM Size : 8 GB RAM

Expandability up to : 64 GB (using spare

DIMM Slots) Type of Drives used to populate

the Internal Bays : PCIe_SSD , Total SSD

Capacity :512 GB, Display Size : 23.8 INCHES,

Display Type : Non Touch, Panel Technology :

IPS Display Resolution : 1920x1080 PIXELS

Availability of Webcam integrated with

Display : Yes Motherboard- Chipset Series:

Intel Q Series, Chipset Number : Intel Q670,

Warranty : 3 Years, Make : HP, DELL or

superior Inspection : Consignee"

164 164 "Supply of Fault and Accident Report Numbers 1.00 19723.73 19723.73

Generation Device. Specification :- Printing

Technology- Laser, Cartidge Technology -

Composit Technology, Paper Size-A4,

Resolution - 1200X1200(Dpi) , Processor

Speed - 400MHz, USB Port- Yes. Certification-

UL,CE, Warranty- 5 Years, Make HP( HP-Laser

1008W), or supirior Inspection : Consignee"

165 165 "Supply of Office table with laminated top Numbers 12.00 10920.34 131044.08

with three drawers on left hand side and one

locker on the right hand side. Olive brown

with duplicate keys. Make: Godrej Model T-9

(136.5 cmX68cmX 75cm)or Similar of

reputed brand. Inspection: Consignee"

166 166 "Supply of Office Chair make Godrej CH-7B or Numbers 25.00 2459.32 61483.00

similar of reputed brand. Inspection:

167 167 "Supply of Steel Plain Almirah with 4 Numbers 12.00 14544.92 174539.04

adjustable slaves Size: 1980mm height, 915

mm width and 485 mm depth. Make: Godrej

Storewel Plain Large or Similar of reputed

brand. Inspection: Consignee"

SEALDAH DIVISION-S AND T/EASTERN RLY

168 168 "Cleaning of Railway premises like thoroughly Numbers 100.00 871.00 87100.00

cleaning of Garbage in the vicinity of Railway

track, cutting of small Bushes/Grass in the

nearby area of Location Box, Signal post, LC

gate etc. This includes cleaning of Store

room, Power room, Battery room, Railway

offices as per instruction of the Railway site

supervisor. Note:- ""NO"" in unit column

means One Person per day."

169 169 "Modification/Alteration in existing EI Numbers 4.00 1477976.27 5911905.08

(Electronic Interlocking) as per latest RDSO

guidelines/TAN. It includes: Design and

modification in existing Interface and

Interlocking circuits and logic of EI system

including modification in the VDU (Video

Display Unit)/ LCP (Local Control panel)/ CCIP

(Control cum Indication Panel), Maintenance

terminal (MPC), Data Logger, Relay rack

wiring. The complete work should comply

with the latest RDSO specifications and

guidelines and as per approved SIP and

circuit diagrams. All the material (Interface

cards/relays/wiring material/

connectors/fuses/communication devices

etc.) shall be provided by the contractor. The

work also includes the supply of modified

Selection table, Interface Circuits,

VDU/LCP/CCIP diagram etc. to suit the

modified SIP. It also includes the carrying out

of FAT, SAT (as applicable) jointly with

Railways and satisfactory commissioning. All

plans/drawings/circuits etc. should be

prepared on AUTOCAD, softcopy to be

supplied on Pen Drive and 06 sets of hard

copies also to be supplied (following the

instructions of IRSEM Para 8.7.1(f) (i, ii) &

Para 8.1.7) Alteration involving modification

in up to 10 routes. Note: 'No' in the unit

column indicates 'per alteration'"

TRANSPORTATION OF MATERIALS INCLUDING

CABLES, LOCATION BOXES AND

MISCLLANEOUS / RELEASED ITEMS REQUIRED

FROM VARIOUS PLACES IN 9 MT TRUCK TO

THE RAILWAY STORE AS PER SITE ENGINEER.

A) TRANSPORTATION "

TRANSPORTATION OF MATERIALS INCLUDING

CABLES, LOCATION BOXES AND

MISCLLANEOUS/RELEASED ITEMS REQUIRED

FROM VARIOUS PLACES IN 9 MT TRUCK TO

THE RAILWAY STORE AS PER SITE. B)

LOADING AND UNLOADING"

SEALDAH DIVISION-S AND T/EASTERN RLY

172 172 DURING THE BLOCK WORKING PERIOD OF Man-Days 351.00 4146.00 1455246.00

ANY DEPARTMENT, DISMENTALLING /

REFIXING / SHIFTING AND OTHER ALLIED

WORK OF SIGNALLING EQUIPMENTS LIKE

CABLE/ TLJB/ POINT MACHINE/ GROUND

FITTINGS/ POINT JB/ AXLE COUNTER TRACK

DEVICE, L.C. GATE, AND OTHER

MISCLLANIOUS WORKS TO BE EXECUTED.

THIS JOB INCLUDES COST OF RELEASING OF

SIGNALLING EQUIPMENTS, GEARS & DEVICES

AND RECONNECTION OF THE SAME AFTER

THE WORK. THIS WORK TO BE EXECUTED AT

ANY TIME OF DAY / NIGHT AS PER THE

INSTRUCTION OF RAILWAY SITE

ENGINEER(S). 1 ELECTRICAL WIRE MAN, 2

FITTER & 1 KHALASIS/ HELPERS TO BE

PROVIDED PER DAY AS ONE(1) GANG FOR