Construction of new Panchayat Office building in Kanikiluppai panchayat in Arni Block of Tiruvannamalai District under AGAMT - II 2022-23

Amount

Construction of new Panchayat Office building in Kanikiluppai panchayat in Arni Block of Tiruvannamalai District under AGAMT - II 2022-23

Earth work excavation and depositing on banks with initial lead and lift in gravelly soil stiff clay, hard stiff clay, murram, boulders mixed with gravel as per SS 20-B for foundation.

Supplying and Filling foundation and basement with filling sand in layers not more than 15cm Thick well ramed, watered and compacted Complete complying with stanard specification.

Filling in Basement with excavated Earth in layers of not more than 15cm. Thick well rammed, watered and consolidated complying with standard specifications etc., complete.

Plain Cement Concrete 1:4:8 mix using 40 mm ISS HBG metal including cost and conveyace of all materials and all labour charges, etc.

Brick work in CM 1:5mix using country bricks, ground moulded of size 23 x 11 x 7cm for the following including curing etc., complete complying with standard specifications. - UPTO BASEMENT

Brick work in CM 1:5mix using country bricks, ground moulded of size 23 x 11 x 7cm for the following including curing etc., complete complying with standard specifications. - ABOVE BASEMENT

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings complete complying with standard specifications and as directed by the departmental officers. - UPTO BASEMENT

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings complete complying with standard specifications and as directed by the departmental officers. - ABOVE BASEMENT

Supplying and Fabricating and placing in position MS steel or Ribbed Tor Steel for all Reinforced Cement Concrete works as per the design given including cost of steel and binding wire in all floors etc, Complete complying with stanard specification.(MS rod or RTS bar will be supplied departmentally at section stores and cost will be recoverd at issue rate). the binding wire shall supplied by the contactor.

Reinforced cement concrete 1: 1 1/2 :3 (One of cement one and half of sand and three of hard broken stone jelly) using 20mm gauge hard broken granite stone jelly for all reinforced cement concrete works excluding cost and fabrication of reinforcement grills. - UPTO BASEMENT

Reinforced cement concrete 1: 1 1/2 :3 (One of cement one and half of sand and three of hard broken stone jelly) using 20mm gauge hard broken granite stone jelly for all reinforced cement concrete works excluding cost and fabrication of reinforcement grills. - ABOVE BASEMENT

Paving the Floor with Vetrified tiles in CM 1:3 20mm thick

Dadooing walls with Glazed tiles of any colour and any size laid in CM 1:2, 10mm thick. and pointing with white cement 0.4 Kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complying with the standard specifications and as directed by the departmental officers. The Glazed tiles should be got approved from the Departmental officers before execution.

Brick jelly lime concrete using 20mm brick jelly with slacked lime in the ratio of 32:12.5 including cost and conveyance of all materials to site and all labour charges for mixing , laying ,and finishing etc complete for 10 cum

Terrace Floor finshed with one course of pressed tiles of size 20x20x2cm with cement mortar 1:3 mix and pointed with the same oiled mortar including cost and conveyance of all materials to site and all labour charges etc complete for 10 sqm

Paving the flooring with special type of flooring tiles (Cement based Hydraulically pressed Anti skid tiles (20mm thick) in CM 1:3, 20mm thick

Finishing the exposed surface of RCC item of work such as slabs, beams, sunshade, facia, canopy slab, staircase waist slab, landing slab etc., with CM 1:3, 10mm thick. including raking the surface. The rate is to include the cost of providing cement mortar beading or nosing for sunshades & staircase steps, landing slabs etc., complete complying with standard specifications.

Plastering with CM 1:5, 12mm thick.over the cement concrete for floor finish including curing etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.

Colour Washing with best Distempering two Coats in to primer coat and two coats with oil bound distember over cement plasterd surface ceiling and other new surface and including clearing,preparing the surface and etc.,complete.

Painting two coats with approved Exterior Emulsion Paint over one priming coat of cement plastered wall surface and ceiling including cleaning preparing the surface and curing etc, complete

Painting new iron works for doors, windows and Ventilators, Iron bars, Weldmesh, wiremesh, screen, steel bars, flats and other similar works etc., with Two coats of approved first quality of synthetic enamel paint over the existing red oxide primer in all floors. The rate is inclusive of cost of all materials and labour, brushes and scaffolding charges etc., complete complying with standard specification.

Fabrication and supply of Mild Steel Door of any required size with double leaf,outter frame of 35x35x 5mm equal MSL angle and shutter frame made of 25x25x5mm equal MSL angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2Nos.horizontal and 3 Nos. diagonal for each shutter using M S flat of size 20x5mm fully covered with 18 gauge plain M S full sheet welded with shutter frame neatly and also fixin by welding 6 Nos. of hold fasts,2 Nos. wind appliances,3 Nos. tower bolts,1 No. aldrop2 Nos. handles, fixing shutterwith6 Nos.of hinges with outter frame of the door including painting the whole unit with one coat best quality of red oxide primer.

Fabrication and supply of Mild Steel Window of any required size with Three leaf.Outter frame of 35x35x 5mm equal MSL angle, Mullion section made of 35x 35x5mm equal T-section, shutter frame made of 25x25x5mm equal MSL angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 1No.horizontal for each shutter using M S flat of size 20x5mm fully covered with 18 gauge plain M S full sheet welded with shutter frame neatly and also fixin by welding.Protective grill with 12 mm squqre M S rods at an intervel of not grater than 10 cm centre to centre to the outter frame.2 Nos of peg stays with hole for keeping the windows open in different positions,2 Nos. of locking handles fixing the shutters with 4 Nos. of hinges hold fasts, 6 Nos.of hinges with outter frame of the window including painting the whole unit with one coat best quality of red oxide primer.

Fixing of Steel rolling shutters including cost and conveyence to work site and labour cherges etc complete

Fabrication and Supply of Steel grill gate of over all size 1500 X 2100 mm using structural steel etc., complete.in all respects as directed (details specification enclosed as annexure)

Solid PVC Door shutter using 19 guage 19mm MS sq. tubes for styles and outer frames, 15mm MS sq. tubes for top, lock and bottom rails. The steel tubes shll be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable suitable rabate for housing the shutter.

Manufacturing Supplying and fixing of stainless steel Hand rails for near wet raiser using 50mm dia 304L Grade Stainless steel pipe of 1.60mm thick thick will be provided with tubler supports made of 304L Grade Stainless steel pipe of 25mm dia of 1.60mm thick welded to the railing. the rate included for grouting into concrete with necessary supporting arrangements the hand railin floor polishing buffing ,cutting grinding,conveyance and welding charges ,electrical charges etc complete

Providing C.F.L / LED / Tube light / Fan Point with all accessories etc. complete

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch and making good of the concealed portion with suitable colour for PVC concealed light / Fan Point (For electronic regulator) (5 Points Per Coil) Concealed (SD 25)

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter locking CS Plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. Concealed (SD38)

Providing Light Fitting with accessories etc. complete

Supply and fixing of fancy glass shade and 11W CFL for BH point. (SD 80)

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting. (SD 88)

Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K. Lite) suitable for11W CFL lamp with CFL. (SD83)

Providing Fan Fitting with accessories etc. complete

Supply and fixing of 1200 mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 300mm down rod on the existing clamp. SD(110)

Supply and fixing of 16 Amps DP Switch of 500 V with matal clad with fuse and neutral (Side Handle) on suitable TW Board with earth connection only. SD(142)

Supply and run of 2 of 1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade on 7/20 GI bearer wire for service connection mains. SD(64)

Supply and run of 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 25mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron upright and end supports for mains. (SD69)

Supply and fixing of 15 A aerial fuse unit(500A) on suitable 100x100 mm TW concealed box with hylem sheet on the tapping pole with necessary clamps. (SD128)

Providing new bore well, motor and specials

Towards Geo physical survey charges

Drilling of 150mm dia Borewell in

Loose soil

Hard Soil

Towards cost of PVC casing pipe

specials

Towards cost and supply of Motor

5.00 HP Motor 75 lpm x 150M head

7.5.0 HP Panel board

Towards Labour Charges for fixing of Motor errection charges with motor and specials including all labour charges etc complete.

Towards E.B.Deposit charges

Provision for Sanitary Arrangements

Provision for Rainwater harvesting arrangement

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}

SINDAN K