Jorhat Airport Road

Amount

Excavation in Soil using Hydraulic Excavator CK 90 and Tippers with disposal upto 1000 metres. (Excavation for roadwork in soil with hydraulic excavator of0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes,in accordance with requirements of lines, grades and cross sections,loading and disposal of cut road with in all lifts and leads upto 1000 metres)

Granular Sub-Base with Coarse Graded Material ( Table:- 400-2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC,and compacting with vibratory roller to achieve the desired density,complete as per cl. 401 II. for grading- II Material (inclusive of all leads & lifts to work site)

Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening /binding material to fillup the interstices of coarse aggregate,watering and compacting to the reqd. density Grading- II Using Screening Type-B (11.2mm Agg.)

Plain/Reinforcedcement concrete, in sub structure complete as per drawing and technical specification and steel shuttering formwork Without plasticiser Height upto 5m PCC Grade M20

Prime coat (Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 1.00 kg/sqm using mechanical means.)( Including cost of testing of materials at site and laboratory as directed by the deptt.) (ii) With bitumen emulsion-CSS-1 ( IS-8887-2004 )

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.( Including cost of testing of materials at site and laboratory as directed by the deptt.) (b) dry & hungry bituminous surface (c) Granular surfaces treated with primer

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.( Including cost of testing of materials at site and laboratory as directed by the deptt.) (a) (a) Normal bituminous surface

Dense Graded Bituminous Macadam (Providing and laying dense bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder@ 4.5 to 5% by weight of total mix and filler transporting the hot miox to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no. 507, complete in all respect. ( including all leads & lifts to work site)( Including cost of testing of materials at site and laboratory as directed by the deptt.) (b) With rock dust as filler ( refer table 500-9 of MoSRT&H specification) A) (a) with 60/70 or VG 30 gr bitumen (I)'with 60/70 or VG-30 grade bitumen (I)'with 60/70 or VG-30 grade bitumen for GradingII(19 mm nominal size)

Bituminous Concrete (Providing and laying bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder@ 5.4 to 5.6% of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.509. complete in all respect.( Including cost of testing of materials at site and laboratoryas directed by the deptt.) B (a) With rock dust as filler ( refer table 500-9 of MoSRT&H specification) (a) with 60/70 or VG 30 gr bitumen (I)'with 60/70 or VG-30 grade bitumen for Grading-II(13 mm nominal size)

Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandator & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand) (i) 90cm equilateral traingle

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Providing ‘Sparkle Solar Road Studs, manufactured by Tata B.P. Solar India Ltd. Of size (125mmx125mm), 90mm height (from bottom of shank to the top of stud) with detachablebattery, m6LEDsthree on each side for Bi-directional studs/3 LEDs on one side for unidirectional studs, ultra bright LED in amber and red colour, weight per stud 700+25 gms, flash rate of 50-65 times per minute completely water resistant and weather proof with replacement warranty and free maintenance fro one year from the date of installation of stud on road-(installation should be made using adhesives and procedures recommended by manufacturer under the supervision of their competent technician). a) Bi-directional Stud-

Providing reflective pavement marker with Micro prismatic lens in both direction having thermoplastic body adhering to the specification and guidelines of MoSRT&H’s fixed to the road surfac using the adhesives and the procedures recommended by the manufacturers with three months replacement warranty and free maintenance.

Painting Lines, Dashes, Arrows etc on Roads in Two Coats on Old Work (Painting lines, dashes, arrows etc on roads in two coats on old work with ready mixed road marking paint confirming to IS:164 on bituminous surface, including cleaning the surface of all dirts dusts and other foreign matter, demarcation at site and traffic control.)Up to 10 cm in width

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. I.Ordinary soil A.Manual Means (b)With dewatering (i) upto 3 m to 6.00m depth

Sand Filling in Foundation Trenches as per Drawing & Technical Specification

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a).Brick on flat soling.

PCC 1:3:6 in Foundation(Plain cement concrete 1:3:6 nominalmix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.)

Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork. (N) Without plasticiser © RCC Grade M 20 Case I Using concrete mixer

Plain/Reinforcedcement concrete, in sub structure complete as per drawing and technical specification and steel shuttering formwork (A) with plasticiser (F) RCC M 20 (a) Ht. up to 5 m Case I Using concrete mixer

Supplying, fitting and placing TMT bar reinforcement in foundation complete as per drawing and technical specifications © With other make ISI marked TMT rebar

Supplying, fitting and placing TMT bar reinforcement in substructure complete as per drawing and technical specifications © With other make ISI marked TMT rebar

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specification

Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification Sandy material

M/S B. L. AGARWALA