SPL REPAIR TO 750 KVA DG SET LSRC POWER HOUSE OF EM I AND REPAIR OF ELECTRICAL CONNECTIONS AND REWIRING IN MAINTENANCE FLIGHT HANGER OF 203 ARMY AVN SQN UH UNDER GE 865 EWS

Amount

Checking, Inspection, maintanance and servicing complete including replacement of unserviceable spare parts of the DG set (comparising of Engine/ Alternator/ Control panel) of the following capacity for smoth functioning complete all as per manufacturers instructions and all as directed by Engineer-in-Charge A. (a) Checking of lubricating oil condition (b) Checking engine for oil, water leakage and correcting the same (c) Checking of all the nut bolts of engine and alternator (d) Checking of all belts and adjust the tenson properly (e) Cleaning of air filters (f) Checking and readjusting the valve clearance (g) Change of Oil/Fuel filters and engine oil if necessary (h) Checking of starter motor battery and charger (i) Checking of cooling system and fuel system (j) checking of all power cables and AVR connections and mounting bolt tightnees of alternator (k) checking the function of AVR genaral checks (l) Checking of control panel meters and gadgets functiong (m) Checking of all control and safety wirings B. (a) Checking of flexible coupling of engine and alternator (b) Cleaning of crank case ventilation pipe (c) Checking of injectors and fuel pump (d) Checking of alternator required for repair of DG set 750 KVA sterling make. NOTE (1) Cost of Spares required will be paid and measured separately (2) Servicing/routine check up carried out through authorised service centre of manufacturer (4) Make of spare recommendation by Sterling viking power Pvt Ltd.

Supply and fixing in replacement of seal 'O' ring Liner slip fit suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of seal 'O' ring inspection cover suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of seal 'O' ring cylinder head water suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of seal 'O' ring cylinder head fuel suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of retainer suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of seal 'O' ring retainer suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket cylinder suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Valve collect suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of cylinder head cover suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Push rod (part No. SE153G) suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Push rod (part No. SE153W) suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket rocker box cover suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket rocker box suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of piston ring kit suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of piston and ring kit suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of injector suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of seal injector (part No. Y03/00033) suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of seal injector (part No. Y03/00034) suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of injector washer suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket breather suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Oil filter suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket water many fold suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of 'O' ring water many fold suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket air pipe suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket turbocharge oil supply pipe suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket turbocharge oil return pipe suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of seal 'O' ring turbocharge suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket turbocharger mounting suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket- IND MANIFOLD (Part No. 282/295) suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket- IND MANIFOLD (Part No. 283/119) suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket-Exhaust MANIFOLD bellows suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket-Exhaust MANIFOLD suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Fuel filter suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Liner slip suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Gasket cam follower suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Big end bearing kit suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of seper filter 01030 suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of Lid Gasket suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of RUBIA TIA 7400 15W40 pack of 50 ltr cane suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of seal 'O' ring piston cooling jet (Part No. 576/174) suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of seal 'O' ring piston cooling jet (Part No. 576/171) suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of centrifugal insert suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of main air filter suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of coolent auto supra suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of consumable item loctite 518, 638 suitable for 750 KVA DG set Make : Sterling complete all as specified and directed by Engr-in-Charge.

Excavating in trenches, n. exc 1.5 m wide and exc 1.5 m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying cables/pipes, etc. n exc 10 sq m on plan in hard/dense soil and getting out soil, complete all as specified and as directed by Engineer-in-charge.

Returning filling in (soil) including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in any type of soil complete all as specifed and as directed by Engineer-in-Charge.

Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specifed and as directed by Engineer-in-Charge.

M&L for sand filling or spreading and levelling in as in cushning/bedding for interlock tiles or cables(8 cm below the cable and 15 cm above the cable and punned thickness of 18 cm will be measured and paid for) etc complete all as specified and directed by Engr-in-Charge.

Supply and laying of factory made, machine pressed, unreinforced precast concrete cable cover class LV type -1 flat size 250 mm x 150 mm x 40 mm complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc removing materials to be store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors etc complete all as speciifed and directed by Engr-in-Charge

M&L for point wiring for one light point or fan point controlled by one light/exhaust fan controlled by one way switch with PVC insulated copper conductor stranded cable of size 1.5 sqmm and including PVC casing/caping terminated in existing sunk CI/pressed steel terminal boxes for fixing and 1.5 sqmm PVC insulated copper wire as earth wire connected to earth wire connected to earth folly and 3.0mm thick plastic laminated sheet cover all as specified and directed by Engr-in-Charge.

All as per item No 7.00 here-in-before but 1.5 Sqmm for one 3 pin 6 Amps socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on the same board complete all as specified and directed by Engr-in-Charge.

All as per item No 7.00 here-in-before but 1.5 Sqmm for one 3 pin 6 amps socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on the independent board complete all as specified and directed by Engr-in-Charge.

All as per item No.7.00 above but using cable 4 Sqmm complete all as specified and directed by Engr-in-Charge

S&F in replacement for lamp holder PVC/Poly corbonate type insulated body with back plate suitable for batten fittings as specified and directed by Engr-in-Charge.

S&F in replacement for switch piano flush type one way single pole 5/6 Amp 240 volts complete all as specified and directed by Engr-inCharge.

S&Fin replacement for switch socket combination 2 in 1, 5 pin, 5/6 Amps, 230 Volts flush type universal complete all as specified and directed by Engr-in-Charge.

S&Fin replacement for switch socket combination mulit purpose 2 in 1, 5 pin, 6 Amps and 16 Amps 230 V flush type universal complete all as specified and directed by Engr-in-Charge.

S&F in replacement for ceiling rose surface bakelite 65x50 mm two to three terminals complete all as specified and directed by Engr-in-charge.

S&F in replacement for LED lights fitting, 1x20 watt, 220 volts, AC ultra bright LED tube light with aluminium heat sink & polycarbonate diffuser having high efficacy suited for installation in existing T5 fitting with G5 lamp holders, led driver outside decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge. Make as per PS.

Supply & laying or fixing and testing of 1100 volts grade duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape overall PVC sheathed solid conductor in service connections 16 Sqmm four core flat/circular cable including taking down existing at any description complete all as specified and directed by Engr-in-Charge. Make as per PS.

Supply & laying or fixing and testing of 1100 volts grade duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape over all PVC sheathed solid conductor in service connections 25 Sqmm four core flat/circular cable complete all as specified and directed by Engr-in-Charge. Make as per PS.

Supply & laying or fixing and testing of 1100 volts grade duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape over all PVC sheathed solid conductor in service connections 35 Sqmm 3.50 core flat/circular cable including taking down existing at any description complete all as specified and directed by Engr-in-Charge. Make as per PS.

Supply & laying or fixing and testing of 1100 volts grade duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape over all PVC sheathed solid conductor in service connections 50 Sqmm 3.50 core flat/circular cable including taking down existing at any description complete all as specified and directed by Engr-in-Charge. Make as per PS.

Supply & laying or fixing and testing of 1100 volts grade duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape over all PVC sheathed solid conductor in service connections 70 Sqmm 3.50 core flat/circular cable including taking down existing at any description complete all as specified and directed by Engr-in-Charge. Make as per PS.

Supply & laying or fixing and testing of 1100 volts grade duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape over all PVC sheathed solid conductor in service connections 95 Sqmm 3.50 core flat/circular cable including taking down existing at any description complete all as specified and directed by Engr-in-Charge. Make as per PS.

Supply and fixing plug-in-Boxes for rising mains/bus bar trucking to branch out connection with 4 pole 250 Amps MCCB 35/50 KA complete all as specified and directed by Engr-in-Charge.

Supply and fix single pole and neutral enclosure with a two pin abd earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and diected by Engr-in-Charge.

Supply and fix TP+N+E solution with insulated plug and socket comprising o plug top and MCB TP 32 Amps complete all as specified and directed by Engr-in-Charge. Havells Cat No DHDPTN032 or equivalent make in PS.

Supply and fix TP+N+E solution with insulated plug and socket comprising o plug top and MCB TP 63 Amps complete all as specified and directed by Engr-in-Charge. Havells Cat No DHDPTN063 or equivalent make in PS.

Sub main wiring with two run of 4.00 Sqmm (2x4 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 4.00 Sqmm (1x4sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 4 Sqmm (2x4sqmm), one run of 4 Sqmm (1x4 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB

Sub main wiring with four run of 10.00 Sqmm (4x10 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with two run of 6.00 Sqmm (2x6 sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 4 runs of 10 Sqmm (4x10 sqmm), two run of 6 Sqmm (2x6 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB

Sub main wiring with two run of 6.00 Sqmm (2x6 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 6.00 Sqmm (1x6sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 6 Sqmm (2x6sqmm), one run of 6 Sqmm (1x6 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB

Sub main wiring with two run of 2.5.00 Sqmm (2x2.5 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 2.5.00 Sqmm (1x2.5 sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 2.5 Sqmm (2x2.5 sqmm), one run of 2.5 Sqmm (1x2.5 sqmm) cable and one metre of PVC casing caping will be measured as one unit.Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB

Supply and fix, testing and commissioning of 415 V 10 KA, 'C' curve TPN 63 Amps complete with connections complete all as specified and directred by Engr-in-Charge Make as per PS.

Supply and fix, testing and commissioning of 240 V 10 KA, 'C' curve SPN 63 Amps complete with connections complete all as specified and directred by Engr-in-Charge Make as per PS.

Supply and fix, testing and commissioning of 240 V 10 KA, 'C' curve SP 5 to 32 Amps complete with connections complete all as specified and directred by Engr-in-Charge Make as per PS.

Supply and fixing in MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts, triple pole neutral 4 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc complete all as specified and directed by Engr-in-Charge. Make as per PS.

Supply and fixing in MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts, single pole neutral 8 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc complete all as specified and directed by Engr-in-Charge. Make as per PS.

Material and labour for earthing complete with galvanised steel earth plate 600 x 600 x 6 mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI wire of size 4 mm dia by means of nuts, bolts, washers etc made of and connected to test point and earth dolly as all shown in electrical plate No.3 of SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil PCC (1:3:6) type C1 in chamber, pre cast RCC slab 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM jali (weight not less than 4.0 kg/Sqm) with cast iron frame, funnel, with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore light grade GI protection pipe, test point, etc, incluidng taking down of old u/s earthing set complete all as specified and as directed. Note: (i) Item includes the cost of 7.5 m GI pipe for protection of earth lead. Any additional length shall be adjusted through deviation order. (ii) Item includes the cost of 7.5 m GI earth lead. Any additional in length shall be adjusted through deviation order ( For Main DBs ) (iii) Item includes the cost of Charcoal and commercial salt ( For Main DBs )

Sona Enterprises

Horizon Construction Company

Rampal Singh Contractor

M/S LIBE & CO