Loading
Loading…
Loading…
Tender Value
₹2.2 Cr
EMD Value
₹4.4 L
Closing Date
1 Jul 2026, 11:00 amClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
FREIGHT
13 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB of GCC 2022, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
1 condition
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Repair and Upgradation of Maintenance facilities at TKD Yard
NRDLI0MCNWWKPR122025RT
NRDLI0MCNWWKPR122025RT
Open
Works - General
6 Months
Delhi, Delhi
₹0
₹4.4 L
1 Jul 2026
3 Jun 2026
11 Jun 2026
248 items across 3 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,15,68,511.47 | ||
| — | 300.00 | — | — | ||
| EARTH WORK // Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. // All kinds of soil | — | — | — | 54,522.32 | |
| — | 200.00 | — | — | ||
| CARRIAGE OF MATERIALS // By Mechanical Transport including loading,unloading and stacking // Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in- charge. | — | — | — | 72,767.2 | |
| — | 140.00 | — | — | ||
| CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. // 1:1.5:3 (1 Cement: 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | — | — | — | 9,63,958.35 | |
| — | 172.00 | — | — | ||
| CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : // 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) | — | — | — | 9,62,516.1 | |
| — | 100.00 | — | — | ||
| CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : // 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | — | — | — | 6,51,521.17 | |
| — | 30.00 | — | — | ||
| CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Centering and shuttering including strutting, propping etc. and removal of form work for : // Foundations, footings, bases for columns | — | — | — | 8,172.38 | |
| — | 25.00 | — | — | ||
| REINFORCED CEMENT CONCRETE // CAST IN SITU // Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : // 1:1.5:3 (1 cement : 1.5 coarse sand (zone- III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) | — | — | — | 1,84,974.28 | |
| — | 20.00 | — | — | ||
| REINFORCED CEMENT CONCRETE // CAST IN SITU // Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : // 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | — | — | — | 1,80,193.9 | |
| — | 20.00 | — | — | ||
| REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Foundations, footings, bases of columns, etc. for mass concrete | — | — | — | 5,448.25 | |
| — | 20.33 | — | — | ||
| REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Lintels, beams, plinth beams, girders, bressumers and cantilevers | — | — | — | 10,940.52 | |
| — | 60.00 | — | — | ||
| REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Columns, Pillars, Piers, Abutments, Posts and Struts | — | — | — | 42,686.37 | |
| — | 3500.00 | — | — | ||
| REINFORCED CEMENT CONCRETE // STEEL REINFORCEMENT // Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. // Thermo-Mechanically Treated bars of grade Fe-500D or more. | — | — | — | 2,77,565.37 | |
| — | 4000.00 | — | — | ||
| REINFORCED CEMENT CONCRETE // STEEL REINFORCEMENT // Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. // Thermo-Mechanically Treated bars of grade Fe-500D or more. | — | — | — | 3,17,217.56 | |
| — | 50.00 | — | — | ||
| MASONRY WORK // Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: // Cement mortar 1:4 (1 cement : 4 coarse sand) | — | — | — | 3,04,390.86 | |
| — | 60.00 | — | — | ||
| MASONRY WORK // Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : // Cement mortar 1:6 (1 cement : 6 coarse sand) | — | — | — | 4,39,912.46 | |
| — | 300.00 | — | — | ||
| CLADDING WORK // STONE WORK DRY CLADDING // Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | — | — | — | 2,82,218.36 | |
| — | 70.00 | — | — | ||
| WOOD AND P.V.C. WORK // BRIGHT FINISHED M.S. FITTINGS // Providing and fixing ISI marked, IS : 1341, M.S. heavy weight bright finishied butt hinges with necessary screws etc. complete : // 125x90x4.00 mm | — | — | — | 3,758.67 | |
| — | 5.00 | — | — | ||
| WOOD AND P.V.C. WORK // COPER OXIDISED MILD STEEL FITTINGS (COPPER OXIDISED AS PER IS: 1378) // Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per IS: 1378) // 300x16 mm | — | — | — | 798.57 | |
| — | 10.00 | — | — | ||
| WOOD AND P.V.C. WORK // COPER OXIDISED MILD STEEL FITTINGS (COPPER OXIDISED AS PER IS: 1378) // Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : (copper oxized as per IS: 1378) // 200x10 mm | — | — | — | 540.05 | |
| — | 10.00 | — | — | ||
| WOOD AND P.V.C. WORK // BRASS FITTINGS // Providing and fixing bright finished brass handles with screws etc. complete: // 125 mm | — | — | — | 1,814.31 | |
| — | 15.00 | — | — | ||
| WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing to existing door frames. // 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (+/- 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (+/- 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer's specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places | — | — | — | 34,661.28 | |
| — | 40.00 | — | — | ||
| WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge. | — | — | — | 14,445.52 | |
| — | 3141.61 | — | — | ||
| STEEL WORK // Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | — | — | — | 3,11,116.69 | |
| — | 1000.00 | — | — | ||
| STEEL WORK // Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. // In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | — | — | — | 1,25,878.58 | |
| — | 3500.00 | — | — | ||
| STEEL WORK // Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. // Hot finished seamless type tubes | — | — | — | 5,23,086.1 | |
| — | 250.00 | — | — | ||
| FLOORING // CERAMIC GLAZED TILES // Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. | — | — | — | 2,52,730.22 | |
| — | 100.00 | — | — | ||
| FLOORING // VITRIFIED FLOOR TILES // Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. // Double charge vitrified tile polished finish of size // Size of Tile 600 x 600 mm | — | — | — | 1,13,812.64 | |
| — | 3000.00 | — | — | ||
| ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | — | — | — | 17,82,159.39 | |
| — | 70.00 | — | — | ||
| ROOFING // Providing, fixing and embedding sand cast iron accessories for rain water pipes in the masonry surrounded with 12 mm thick cement mortar of the same mix, as that of masonry (lead caulking will be paid for separately): // Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. // 110 mm diameter | — | — | — | 19,799.56 | |
| — | 750.00 | — | — | ||
| ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. // 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified | — | — | — | 7,82,373.41 | |
| — | 300.00 | — | — | ||
| ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : // Ridges plain (500 - 600mm) | — | — | — | 1,19,580.23 | |
| — | 100.00 | — | — | ||
| FINISHING // CEMENT PLASTER (IN FINE SAND) // 15 mm cement plaster on the rough side of single or half brick wall of mix : // 1:4 (1 cement: 4 fine sand) | — | — | — | 30,049.86 | |
| — | 850.00 | — | — | ||
| FINISHING // Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : // New work (two or more coats) over and including water thinnable priming coat with cement primer | — | — | — | 1,22,222.97 | |
| — | 1000.00 | — | — | ||
| FINISHING // EXTERIOR FINISHING // Finishing walls with water proofing cement paint of required shade : // New work (Two or more coats applied @ 3.84 kg/10 sqm) | — | — | — | 86,336.96 | |
| — | 800.00 | — | — | ||
| FINISHING // EXTERIOR FINISHING // Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : // Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm | — | — | — | 1,12,485.74 | |
| — | 800.00 | — | — | ||
| FINISHING // Extra for plastering: // Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | — | — | — | 1,51,655.82 | |
| — | 2000.00 | — | — | ||
| FINISHING // EXTERIOR FINISHING // Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : // Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture | — | — | — | 2,47,776.46 | |
| — | 400.00 | — | — | ||
| REPAIRS TO BUILDING // Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. // With cement mortar 1:4 (1 cement : 4 fine sand) | — | — | — | 1,63,580.23 | |
| — | 12.00 | — | — | ||
| REPAIRS TO BUILDING // ROUTINE MAINTENANCE WORK // Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge. | — | — | — | 3,795.46 | |
| — | 12.00 | — | — | ||
| DISMANTLING AND DEMOLISHING // Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | — | — | — | 31,082.37 | |
| — | 15.00 | — | — | ||
| ROAD WORK // MISCELLANEOUS // Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67- 2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). // Overhead informatory road signage | — | — | — | 74,433.12 | |
| — | 1500.00 | — | — | ||
| ROAD WORK // MISCELLANEOUS // Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. // 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. | — | — | — | 13,41,761.28 | |
| — | 6.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: // White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | — | — | — | 30,685.09 | |
| — | 6.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : // W.C. pan with ISI marked white solid plastic seat and lid | — | — | — | 29,407.02 | |
| — | 6.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : // One urinal basin with 5 litre white P.V.C. automatic flushing cistern | — | — | — | 27,964.95 | |
| — | 4.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: // White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap | — | — | — | 6,771.61 | |
| — | 4.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: // White glazed fire clay kitchen sink of size 600x450x 250 mm | — | — | — | 11,687.16 | |
| — | 6.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : // Flat back wash basin of size 550x400 mm | — | — | — | 4,858.84 | |
| — | 6.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. // Semi rigid pipe // 32 mm dia | — | — | — | 482.73 | |
| — | 6.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. // Semi rigid pipe // 40 mm dia | — | — | — | 539.52 | |
| — | 6.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. // Flexible pipe // 32 mm dia | — | — | — | 553.85 | |
| — | 6.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. // Flexible pipe // 40 mm dia | — | — | — | 553.85 | |
| — | 6.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : // Rectangular shape 453x357 mm | — | — | — | 6,151.24 | |
| — | 30.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing soil, waste and vent pipes : // 100 mm dia // Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 | — | — | — | 28,592.04 | |
| — | 6.00 | — | — | ||
| SANITARY INSTALLATIONS // Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. // 100 mm dia // Sand cast iron S&S as per IS - 1729 | — | — | — | 2,816.74 | |
| — | 55.00 | — | — | ||
| SANITARY INSTALLATIONS // Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : // 100 mm dia | — | — | — | 29,955.65 | |
| — | 150.00 | — | — | ||
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.-Internal work - Exposed on wall // 15 mm dia nominal bore | — | — | — | 40,357.66 | |
| — | 5.00 | — | — | ||
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : // 15 mm nominal bore | — | — | — | 1,160.15 | |
| — | 10.00 | — | — | ||
| WATER SUPPLY // C.P. BRASS FITTINGS // Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 // 15mm nominal bore | — | — | — | 4,426.1 | |
| — | 20.00 | — | — | ||
| WATER SUPPLY // PTMT FITTINGS // Providing and fixing PTMT bib cock of approved quality and colour. // 15 mm nominal bore, 122mm long, weighing not less than 99 gms | — | — | — | 2,535.26 | |
| — | 20.00 | — | — | ||
| WATER SUPPLY // PTMT FITTINGS // Providing and fixing PTMT pillar cock of approved quality and colour. // 15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms | — | — | — | 3,434.9 | |
| — | 100.00 | — | — | ||
| ALUMINIUM WORK // Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : // For fixed portion // Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) | — | — | — | 41,991.96 | |
| — | 98.00 | — | — | ||
| ALUMINIUM WORK // Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : // For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) // Powder coated aluminium (minimum thickness of powder coating 50 micron) | — | — | — | 48,962.96 | |
| — | 10.00 | — | — | ||
| — | — | — | 11,725.82 | ||
| — | 2.00 | — | — | ||
| — | — | — | 4,332.51 | ||
| — | 2.00 | — | — | ||
| ALUMINIUM WORK // Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : // Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer- in-Charge. // Powder coated minimum thickness 50 micron aluminium tubular handle bar | — | — | — | 996.94 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCCWorks2022withcorrectionslipsuptoACS10.pdf
ATTACHMENT
CECIRCULAR6301.pdf
ATTACHMENT
TecnicalspecforPitlight.pdf
ATTACHMENT
TECHSPEC-III.pdf
ATTACHMENT
technicalSpecforLEDBasedLuminaries.pdf
ATTACHMENT
TECHNICALSPECIFICATIONSFORREWIRINGWIRING.pdf
ATTACHMENT
TecnicalSpecfortheOuterdoortypefeederoutdoortypefeederpillarfor440V.pdf
ATTACHMENT
FinalTDofTKDUppgradationRT01-06-2026_1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .