Renovation of Community Hall at Periyar Nagar,Nellithope, Puducherry.

Amount

Brick work with FPS bricks of class designation 35 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand)

12mm cement plaster of mix :Cement mortar 1:4 (1 cement : 4 fine sand)

Cement concrete flooring 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm nominal size stone aggregate.

Supply of Quary rubbish including stacking to department gauge for premeasurement and spreading required thickness as directed by the Engineer-in-charge

Supplying and filling in plinth with river sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level 1:5:10 (1 cement : 5 sand : 10 graded stone aggregate 40mm nominal size

Renewing glass panes and refixing existing wooden fillets - Float glass panes of thickness 4mm.

Renewal of old putty of glass panes (length)

Poilshing the existing mosaic floor with power polisher to a high degree of polish as to be perfectly smooth .

Acid cleaning for the existing Mosaic floors, glazed tiles work and removing the stains and decays to give a glassy look etc complete (The acid used shall be 32% concentrated hydrochloric acid after taking on the precautionary measures)

Providing and fixing 30mm thick door shutter made of soild PVC foam profile. The styles & rails shall be of size 75mm x 30mm having wall thickness 5mm. The styles, top & bottom rails shall have one side wall thickness of 15mm integarally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33mm x 17mm x 1mm, painted with primer, all four corners of reinforcement to be welded or sealed . Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of pvc solvent cement & Self driven self taping screws. Single piece extruded solid PVC lock rail of size 100mm x 30mm with wall thickness 5mm & 15mm integrally extruded in the middle

Supplying and fixing CI cover without frame for manholes 455x610mm rectangular CI cover (light duty) the weight of the cover to be not less than 23 Kg.

Finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer specifications including appropriate priming coat, preparation of surface, etc. complete - On Steel work.

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian WC pan) with seat lid with C.P brass hinges and rubber buffers, 10 litre low level flushing cistern with fittings and brackets, 40mm flush bend 20mm over flow pipe with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fitting and brackets, cutting and making good the walls and floors wherever required. White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and CP flush bend.

Providing and fixing wash basin with CI brackets, 15mm CP brass pillar taps 32 mm CP brass waste of standard pattern including painting of fittings and brackets, cutting and making good the walls wherever required White vitreous china flat back wash basin size 550x400mm with single 15mm CP brass pillar taps

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall) - 32mm nominal outer dia pipes

Providing and fixing in position G.I. Hex nipple (UNIQUE/R Brand/HB Brand/UI Brand) conforming to IS 1239 part II and ISI marked,including labour charges for jointing,jointing materials etc,complete - 40 mm dia.

Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) - 25 mm nominal bore.

Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) - 32 mm nominal bore.

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall) - 25mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall) - 20mm nominal outer dia pipes

Providing, laying and jointing UPVC pipes(Finolex/Jain) (0.6 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches,laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends,tees, threaded pieces, couplers,reducer, endcaps etc.,complete all as per IS and CPWD specification. - 110mm dia

Providing and fixing in position UPVC fabricated bend (Finolex/Jain)(0.4 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110 mm dia

Providing and fixing in position UPVC moulded elbow (Finolex/Jain)(1 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110mm dia

Providing and fixing in position UPVC moulded equal Tee (Finolex/Jain)(0.6 Mpa) jointing, jointing materials etc,complete - 110mm dia conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110mm dia

Providing and fixing ball valve (brass) of approved quality complete. high or low pressure with plastic floats - 20 mm nominal bore.

Providing and fixing brass bib cock of approved quality - 15mm nominal bore.

White washing with lime to give on even shade - New work three or more coats).

Finishing walls with Acrylic Smooth exterior paint of required shade - New work (Two or more coat applied @ 1.67 ltr / 10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg / 10 sqm)

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc.complete - 125x65x2.12mm

Wall painting with plastic emulsion paint - Premium of approved brand and manufacture to give an even shade - One or more coats on old work

Lettering with black Japan paint of approved brand and manufacture. (Cost for 1 letter of 1 cm height)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - One or more coats on old work.

Providing and fixing of 65mm Godrej Navtal lock of 6 levers etc complete

Removal of sludge from the septic tank and disposal of the same through the sewage tanker in safe location with an average lead of 10Km the rate to include the cost of labour charges for removing and relayingof cover slab laid over the septic tank mixing of ferro sulphate in to the septic tank for thorough mechanical device and disposal of the same including hire chrages for sewage tanker etc., complete as directed by the Engineer-in-charge. Approved vide Lr.No.6112/PW/SE-II/AE(P)6/SB150/2016-17/1945 dt.24.11.2016

12mm thick plain cement mortar bands in cement mortar 1:4 (1 cement : 4 fine sand) - Flush Band. (Cost for 1 metre long and 1 cm wide band)

Wrought iron and mild steel welded work (using angles, square bars, tees and channel grills, grating frames, gates and treeguards of any size and design etc. including cost of screens and welding rods or bolts and nuts complete fixed in position but without the cost of excavation and concrete for fixing which will be paid separately.

Providing and fixing to existing door frames - 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm x 25 mm or less as per requirement with an average wall thickness of 1 mm (+-0.3mm ). PVC foam end cap of size 23 x 10mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S.tube having dimensions 19 mm x 19 mm and 1.0 mm (+- 0.1mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end -cap of the size 25 mm x 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer's specification to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places

Supplying and drawing of 1.5 Sqmm. FR PVC insulated, copper conductor, single core cable in the existing surface/recessed, PVC/steel conduit/PVC casing and capping as required. Make: Finolex/Polycab

Supply and fixing of 40W tube light

Supply and fixing of 1x40W single tube box type fitting with copper choke, tube light with fixing charges, including connection and testing as required. Make: Philips/Bajaj.

Supplying and fixing of 1200mm sweep double ball bearing ceiling fan with fixing charge, including connection and testing as required. Make: Almonard/Usha.

Supplying and fixing of 70Watts Metal Halide fitting with control gear box with bulb and fixing charge, including connection and testing as required. Make: Philips/Bajaj.

Supplying and fixing of Bulk head fitting aluminium alloy body heat resistant prismatic glass cover with specially designed gasket, with 100W incandescent bulb with fixing charges, including connection and testing as required. As directed by the Engineer in charge. Make: Philips/Bajaj

Supply and fixing of 15mm dia G.I. pipe. 1Mtr length (ceiling fan down rod)

Finishing walls with Acrylic Smooth exterior paint of required shade - Old work (Two or more coats applied @ 1.43 lts/10 sqm) over existing cement paint surface.

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee with door - 75 x75x75mm

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee with door - 110x110x110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - bend 87.5 degree - 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs ,screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm

Providing and fixing sheet covering over expansion joints with iron screws as per design to match the colour / shade of wall treatment - Non - asbestos fibre cement board 6mm thick as per IS:14862 - 150mm

Providing and fixing 15cm wide ,45cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3 mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete - 0.80 mm thick with zinc coating not less than 275 gm / sq.m

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - bend 87.5 degree - 75mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 75mm shoe

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs , screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 75mm

C MOGANASOUNDIRAME