REPAIRS TO ROLLING SHUTTERS COLLAPSIBLE GATES JOINERY GRILLS ALUMINIUM DOOR AND WINDOWS INCLUDING REPLACEMENT TO ROOF SEWAGE AND SANITATION ALONGWITH MISC B R WORKS AT HEMRL SUTARWADI PUNE UNDER GE RD PASHAN PUNE

Amount

Taking down hood covers of rolling shutters, loose brackets plates or guide, properly greasing helical spring, shafts, and guide channel for proper functioning of rolling shutters of the following size and refixing hood covers in position after repairs complete all as specified and directed of following size :- (a) Upto 10 Sqm area of shutter.

(b) Exceeding 10 Sqm but n.exc 15 Sqm area of shutter.

All as per Sl item No.1 here-in-before but with gear box assembly and area upto 36 Sqm complete all as specified and directed.

Taking down rolling shutter any type including top covers for carrying out repairs/ replacement of worn out parts and straightning partition, side patti, press button, rails, tightening end clips, cleaning and greasing the parts to make the rolling shutter in good condition and refixing in position for complete all as specified and directed of following size :- (a) Shutter area n.exc 10 Sqm. Note :- Spares/worn out parts required to be replaced shall be measured and paid seperately as 'Supply only'.

(b) Shutter area exc 10 Sqm but n.exc 15 Sqm. Note :- Spares/worn out parts required to be replaced shall be measured and paid seperately as 'Supply only'.

(c) Shutter area exc 15 Sqm. Note :- Spares/worn out parts required to be replaced shall be measured and paid seperately as 'Supply only'.

Material and Labour for repairing the steel collapsible gate including taking down the gate and replacing/ wornout parts such as mild steel flat, channel, bottom and top rails including revetting and cleaning, greasing and resecuring in good working condition complete all as specified and directed. Note :- Spares/worn out parts required to be replaced shall be measured and paid seperately as 'Supply only'.

Supply only the following item as per existing (to be replaced against Srl item 4 to 7 here-in-before) complete all as specified and directed:- (a) Heavy duty spring upto 35 cm long.

(b) Heavy duty spring exc 35 cm and n.exc 45 cm long.

(c) Gear box set.

(d) Gear wheel (steel/CI).

(e) Gear worm.

(f) Shaft wheel with bearing.

(g) Gear box handle.

(h) Press button rail unit.

(j) Side guide (12 guage).

(k) End clip.

(l) Safety lever lock MS.

(m) Partition patties 75 mm wide (mild steel strip).

(n) Heavy duty shaft pipe mild steel of 40 mm dia.

(o) Heavy duty shaft pipe mild steel of 50mm dia.

(p) Top Cover (18 gauge).

(q) Mild steel flat 18 x 5mm or any other section.

(r) MS Channel and similar MS work required for collapsible gate.

Taking down rolling shutter any type including top covers complete of following sizes complete all as specified and directed:- (a) Area n.exc 10 Sqm.

(b) Area exc 10 sqm but n.exc 15 sqm.

Supply and fix factory made steel rolling shutters of thickness of laths 1.00 mm, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated complete push pull or manual type complete all as specified and directed.

All as per item No.27 here-in-before but gear operated type with bevel gear box and crank handle complete all as specified and directed.

Taking down steel collapsible gate of any type complete all as specified and directed. (a) Area of gate exc 10 Sqm

(b) Area of gate exc 10 sqm but n.exc 15 sqm.

Supply and fix factory made collapsible steel gates top hung consisting of channel pickets, pivoted flat bars top and bottom runners brass handles etc as specified erected in position and securing runners with holdfasts and brackets complete all as specified and directed.

Material and Labour (in replacement) double action floor door spring hydraulically regulated made up of minimum 1.25 mm thick aluminium aloy sheet foundation body, main box with stainless steel cover, governing pivot made of brass, other part made of mild steel heavy duty for aluminium doors complete all as specified and directed.

Material and Labour for repairing aluminium door by taking out frame alongwith shutter, fixing missing screw to wall, adjusting floor spring, repairing hook joints of frame and re-erecting in good working condition by necessary lubrication complete all as specified and directed. Note Aluminium tee /angle required to be replaced will be measured and paid separately as 'supply only'.

Material and Labour for repairing aluminium sliding window by taking out frame with shutters for alignment correction, fixing missing screws to wall, replacing bearing & locking arrangements, rubber gasket, wherever required, oiling and re-erecting for proper sliding etc complete all as specified and directed. Note Aluminium tee /angle required to be replaced will be measured and paid separately as 'supply only' item.

Supply only standard anodized aluminium sections of required size (powder coated) for door /window /ventilator /partitions /snap grid ceiling etc complete all as specified and directed.

Supply and fix (in repairs) standard Aluminium powder coated concealed lock (ISI marked) of standard quality for sliding aluminium windows complete all as specified and directed.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets and frame complete all as specified and directed.

Supply and fixing standard Anodised aluminium snap grid frame work powder coated (minimum thickness of powder coating 50 micron) for false ceiling all as specified including hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40m x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified perforated particle board/tiles 12 mm thick for insulation and acoustic purposes, 60cm x 60 cm in size, fixed to frame work or with staples on snap grid as per manufacturers specifications and instructions complete all as specified and directed.

Taking down door /window shutters only, area exc 1.00 sqm and n.exc 2.00 Sqm each complete all as specified and directed.

Taking down Chowkat with Shutter (Without taking down shutters from the Frame) area exc 1.5 Sqm and n.exc 4 Sqm each complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutters from the frame) area n.exc 1.5 Sqm each complete all as specified and directed.

Material and Labour for Powder coated (minimum thickness of powder coating 50 micron) standard aluminium section for door/window / Ventilators/partition etc frames & shutters including joining cleat, mullion, grills etc.sliding/openable type complete of standard sections as per manufacturer specifications & instructions complete all as specified and directed. Make Jindal/Hindalco/ Indalco.

Supply and fix stainless steel wire mesh 0.45 nominal dia of wire and average width of aperture 1.40mm fixed with aluminium wire staples complete all as specified and directed.

Supply and fix 4 mm thick Figured glass, pin head type and glazing in squares in exc 0.5 sqm in each pane complete all as specified and directed.

Supply and fix factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube wood grain printed PVC sheet used instead of palain colour sheet and edges will be printed to match with printed sheet complete all as specified and directed.

Supply and fix Factory Made Solid PVC Moulded Door Shutters with wood free EPS 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Prelam/plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed

Supply and fix Factory made 35mm thick flush shutter solid core with block board core and plywood face panels commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fix 2nd class hard wood plain, solid, staight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fix Factory made Plain framed, panelled shutter 35 mm thick(two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed

Material and Labour for preparation of wood and wood based surfaces of any description over 10cm width/girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and Labour for preparation of old steel surfaces of any description over 10 cm width /girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Supply and fix 300mm Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and fix Aluminium anodised barrel tower bolt, 150 mm of extruded complete all as specified and directed.

Supply and fix 150mm long Aluminium anodised handle cast type complete all as specified and directed.

Supply and fix MS butt hinge 100 mm long, medium weight, cold rolled complete all as specified and directed

Supply and fix 250mm Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and fix 140mm size, floor door stopper of aluminium alloy body and tongue with hard drawn spring complete all as specified and directed.

Supply and fix in repair Aluminium anodised barrel tower bolt, 150 mm of extruded complete all as specified and directed.

Supply and fix in repair 150mm long Aluminium anodised handles cast type complete all as specified and directed.

Supply and fix in repair MS butt hinge 100 mm long, medium weight, cold rolled complete all as specified and directed.

Supply and fix in repair/replacement 140 mm size, floor door stopper of aluminium alloy body and tongue with hard drawn spring complete all as specified and directed.

Supply and fix in repair 250mm Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed

Supply and fix rough cast wired figured glass, 6.4 mm thick to steel frame and glazing with oil putty in square n.exc 0.5 Sqm in each pane, complete all as specified and directed.

Supply and fix 4.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

Supply and fix figured glass, 4.0mm thick pin head type and glazing with oil putty in square in each pane complete all as specified and directed.

Supply and fixing 4mm thick sheet glass including hacking out old broken glass (any thickness, size, quality or description from metal frame including punching or drilling out old glazing pines /spring clips and providing and fixing new glass complete all as specified and directed.

Supply and fixing 4mm thick sheet glass including hacking out old broken glass (any thickness, size, quality or description from wooden frame including punching or drilling out old glazing pines /spring clips and providing and fixing new glass complete all as specified and directed

Dismantling of asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as specified and directed.

Material and Labourfor 6 mm thick asbestos cement, corruguted or semi corrugated sheets in roofs, wall etc, fixed with L type or J type or cranked hook bolts completed all as specified and as directed.

All as per item No. 71 here-in-before but except sheet(using old serviceable sheet) -ditto-.

Material and Labourin repair for Asbestos cement two piece adjustable plain wing ridge 6mm thick fixed with L type or J type or cranked hooks bolts complete all as specified and as directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering

Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws or by 'J' hooks complete all as specified and directed.

Supply and fix Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

Supply and fix for Fibre glass reinforced translucent corrugated sheeting (ISI marked) with two corrugation side lap fixed with L or J type or cranked hookd and washer in roof, wall etc complete all as specified and directed

Supply and fixing framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doo0rs etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; confirming to Fe.290 (Grade E-165) also fastening and fixing complete all as specified and directed

Supply and fix in repairs Aluminium Door closer hydraulically regulated estruded section, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and directed

Taking down cement plaster on brick / concrete / stone surface including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.

Material and labour rendering 5 mm thick in cement mortar 1:3 on concrete surfaces as in ceiling finished even & smooth without using extra cement complete all as specified and directed.

Material and Labourfor 15mm thick rendering on brick work/block masonry in cement mortar(1:4) in two layers 10 mm thick in first layers and 5 mm thick in second layers with water proofing compound finished fair and even without using extra cement complete all as specified and directed. (NOTE :- Water proofing compound shall be paid and measured separately) as supply only.

Material and Labour for 10mm thick rendering on brick work/block masonry in cement mortar(1:6) finished even and smooth without using extra cement complete all as specified and directed.

Material and Labour for preparation of new plastered surfaces of walls including 3mm wall care putty and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Material and Labour for preparation of new plastered surfaces of walls and applying three coats of white wash on ceiling complete all as specified and directed

Material and Labour for two coats of weather coat(Exterior) all guard emulsion, any colour/tined to old wall surfaces over a coat of primer including complete removal of existing teatment complete all as specified and directed.

Supply only liquid water proofing compound ISI marked complete all as specified and directed.

Material and Labour for one coat of synthetic enamel paint to old wooden surface over 10 cm width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for one coat of synthetic enamel paint to old steel surface over 10 cm width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for one coat of aluminium paint to old steel surface over 10 cm width or girth including preparation of surfaces complete all as specified and directed.

Material and labour for PCC 1:2:4, type B0 (using 12.5mm graded crushed stone aggregate) as in benching, copings, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary formwork, complete all as specified and directed. Note :-Water proofing compound shall be measured and paid separetely as 'supply only'.

Dismantling of existing old padding concrete of any thickness of existing water proofing treatment over the RCC slab other than beams, chajjas, staircase etc by chipping of with porper tools viz chiesel and with applying reasonable force so as to avoid any damages to existing RCC roof slab complete all as specified and directed.

Material and Labour for PCC 1:2:4 (Type B0 using 12.5 mm graded crushed stone aggregate) levelling course average thick 40 mm, to match the undulations of roof and to provide slope accordingly to drain out the rainwater including necessay form work complete all as specified and directed. Note : Liquid water proofing compound will measured and paid separately as 'supply only'.

Material and Labour for rendering 10 mm thick on green fair faces of concrete surface in cement mortar 1:4 for receive the roof finishes with water proofing compound complete all as specified and directed. (WPC Shall be measured and paid separately as 'supply only').

Material and Labour for APP based polymeric memberane minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyester non wove fabric(wt not less than 160 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 litre/Sqm by forced complete all as specified and directed. Water roof treatment consist of as under :- (i) Applying one coat of bituminous primer conforming to IS-3384 @ 0.3 litre per sqm (ii)Laying APP based memberance as specified thick ness and weight (iii)Applying one coat of bitumen grade 85/[email protected] Kg/Sqm (iv)Applying two coats of aliminium paint @ 100ml/Sqm in each coat. Note : (i) The work should be executed through authorised applicator only. Approval of which shall be taken from GE before commencement of work. (ii) The contractor has to furnish guarantee for 10 years for APP membrane.

Taking down old PVC/CI/RCC pipes of any bore and length complete all as specified and directed

Supply and fix PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm bore complete all as specified and directed.

Supply and fix PVC (SWR) bend any radius, shoe, socket etc 160mm bore including clamp complete all as specified and directed.

Material and Labour for dismantling and taking out existing strip type lightening arrestor and refixing the same in position with fixtures and fittings and making good disturbed portion on roof surfaces complete all as specified and directed.

Supply and fix in repair venetion blind with 100mm wide strips with all connected accessories of approved make and quality all as directed including taking down existing unserviceable blinds complete all as specified and directed. Make : Vista/ Saint Gobian or equivalent ISI marked make as approved by GE.

Material and labour for cleaning of existing of sewage lines 200mm dia from manholes to manholes by mechanical means for cleaning eye to eye complete all as specified and directed.

Material and labour for cleaning of existing of sewage lines 150mm dia from manholes to manholes by mechanical means for cleaning eye to eye complete all as specified and directed.

Material and labour for cleaning of existing of sewage lines 100mm dia from manholes to manholes by mechanical means for cleaning eye to eye complete all as specified and directed.

Cleaning of existing manholes of any size and n. exc 1.00 metre depth from GL including removing sludge, silt, solid particles etc and washing the MH with fresh waterand disposing off the same to a distance not exc 50 m and berried the same all as specified and as directed.

Cleaning of existing manholes of any size and exc 1 metre and not exc 2metre depth from GL including removing sludge, silt, solid particles etc and washing the MH with fresh waterand disposing off the same to a distance not exc 50 m and berried the same all as specified and as directed.

Cleaning of gully traps/nahani traps etc of any size, any type all as specified and directed by Engineer-in- charge.

Demolition & breaking up drain pipes (salt glazedwere/AC/RCC ) set in cement mortar,dia of pipe 100 mm dia all as directed at site.

Demolition & breaking up drain pipes (salt glazedwere/AC/RCC ) set in cement mortar,dia of pipe 150 mm dia all as directed at site.

Demolition & breaking up drain pipes (salt glazedwere/AC/RCC ) set in cement mortar,dia of pipe 200 mm dia all as directed at site.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in hard/ dense soil complete all as specified and directed.

Removing excavated material to distance n exc 50m and depositing where directed at a level n exc 1.50m complete all as specified and directed.

Material and Labour PCC (1 : 3: 6 ) type C2(using 40 mm graded crushed stone aggregate) as in bed to drain pipe including packing under & haunching against the sides of pipes of 150 mm dia after they are laid tested including necessary form work complete all as specified and directed. Note: Thickness of bed below pipe shall be 10cm and width shall be outer dia of pipe plus 30cm.

Material and Labour PCC (1 : 3: 6 ) type C2(using 40 mm graded crushed stone aggregate) as in bed to drain pipe including packing under & haunching against the sides of pipes of 200 mm dia after they are laid tested cement mortar complete all as specified and directed. Note: Thickness of bed below pipe shall be 10cm and width shall be outer dia of pipe plus 30cm.

Material and Labour PCC (1 : 3: 6 ) type C2(using 40 mm graded crushed stone aggregate) as in bed to drain pipe including packing under & haunching against the sides of pipes of 100 mm dia after they are laid tested cement mortar complete all as specified and directed. Note: Thickness of bed below pipe shall be 10cm and width shall be outer dia of pipe plus 30cm.

Material and Labour for reinforced concrete pipes, class NP2 (ISI marked) , laid and jointed with collars of dia 150 mm complete all as specified and directed.

Material and Labour for reinforced concrete pipes, class NP2 (ISI marked), laid and jointed with collars of dia 200 mm complete all as specified and directed.

Material and Labourfor reinforced concrete pipes, class NP2 (ISI marked), laid and jointed with collars of dia 100 mm complete all as specified and directed.

Demolition of reinforced cement concrete of any descreption and in anyposition above or below ground level complete.

Demolition of brick work or stone/boulder masonry built in cement morter or cement lime mortar including all quoins,pillars,arches etc, and clearing off the premises.

Material and Labour for PCC 1 : 4 : 8 type D 2, (using 40 mm graded crushed stone aggregate) for foundation filling and bed concrete complete all as specified and directed.

Material and Labour for brick work with subclass 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar (1:4) complete all as specified and directed.

Material and Labour for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

Material and Labour for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 but except stone using old serviceable stones complete all as specified and directed.

Material and Labour pre-cast cement concrete block masonrytype C1 1:3:6 (using 20mm graded crushed stone aggregate) with solid blocks exc. 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner grith in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc.complete all as specified and directed.

Material and Labour for precast cement concrete type B1 1:2:4 (using 20 mm graded crushed stone aggregate) as in landings,cover slabs for man holes etc and similar articles with plain faces set in cement morter(1:4) complete all as specified and directed.

Material and Labour for mild steel deformed TMT bars 6 to 8 mm dia and over cut to length bent to shape required including cranking bending spirally etc and binding with M.S. wire (annealed) not less than 0.9 mm dia or securing clips complete all as specified and directed.

Material and Labour for rendering 10mm thick cement plaster in cement mortar 1:4 on other than fair faces of brick/concrete surfaces finished even and smooth with using WPC @3% by weight of cement complete all as specified and directed. Note :- Integral water proofing compound shall be measured and paid separately as "Supply only".

Material and Labour for PCC 1:3:6 type C2, (using 40 mm graded crushed stone aggregates) as in surface channel and drains complete all as specified and directed.

Cleaning of existing septic tank by removing water,sludge, stones,solid particles etc complete from the septic tank and removing the same from the campus and burried debris/sludge obtained complete all as specified and directed for capacity of tank 50 to 100 users complete all as specified and directed.

Cleaning of existing septic tank by removing water,sludge, stones,solid particles etc complete from the septic tank and removing the same from the campus and burried debris/sludge obtained complete all as specified and directed for capacity of tank 10 to 50users complete all as specified and directed.

Supply and fix PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor 110mm complete all as specified and directed.

Supply and fix PVC (SWR) pipes double socketed in any length with rubber ring joints laid in trenches or in floor 110mm complete all as specified and directed.

Supply and fix PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor 75mm complete all as specified and directed.

Supply and fix PVC (SWR) pipes double socketed in any length with rubber ring joints laid in trenches or in floor 75mm complete all as specified and directed.

Supply and fixing PVC bends, 110mm dia complete all as specified and directed.

Supply and fixing PVC bends, 75 mm dia complete all as specified and directed.

Supply and fix Rotational moulded polyethylene water storage tanks 500 litres capacity (ISI Embossed) (cylindrical vertical with closed top) triple layered hoisted and fixed in position all as specified and directed including dismantling and removing to store complete all as specified and directed.

Supply and fix Rotational moulded polyethylene water storage tanks 1000 litres capacity (ISI Embossed)(cylindrical vertical with closed top) triple layered hoisted and fixed in position all as specified and directed including dismantling and removing to store complete all as specified and directed.

Supply and fixing 20mm Ball brass valve, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed in repairs complete all as specified and directed.

Supply and fixing 20mm Gun-metal, globe or gate valve, with iron wheel head, screwed both end for iron pipe and fixed in repairs complete all as specified and directed.

Supply and fixing 15mm CP fancy type Bib tap, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs complete all as specified and directed.

Supply and fixing 15mm CP fancy type stop valve, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs complete all as specified and directed.

Supply and fix in repairs PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supply and fix in repairs Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain and plug and porcelain stopper but fixing on existing brackets, including cutting for and pinning in ends of brackets or erecting stand, including supply and fixing of flexible waste outlet pipe complete all as specified and directed.

Supply only 32mm bore waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms, suitable for vitreous china wash basin complete all as specified and directed.

Supply and fix 10Litres capacity flushing cistern PVC valveless, syphonic action type, flushing cestern, low level, white, with inlet, ball valve, float and handle including brackets, fixed in repairs complete all as specified and directed.

Supply and fix Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts (excluding flushing cistern and flush pipe) add fixed in repairs including pan seat cover complete all as specified and directed.

Supply and fix in repairs Vitreous China squatting pan, `Orissa' pattern, size 580mm x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including provision of cement concrete bedding complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Supply and fix Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. of Fe -290(grade E-250) (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortor bedding (but not backing) complete all as specified and directed.

Material and Labour for glazed, coloured (including desiner tiles as approved by GE) ceramic tiles in verticle surface of size 300mm x 450mm x 7 to 8mm thick set and joined in neat cement slurry and pointed in cement slurry and pointed in white or coloured cement to match including rendering 10 mm thick in cement mortar 1:4 complete all as specified and directed.

Material and Labour for skid coloured ceramic tlies 7 to 8 mm thick (Square/rectangular ) area of each tile exceeding 0.06 sqm but n.exceeding 0.11 sqm in floors etc. set and jointed in net cement slurry and pointed in white coloured cement to match coloured tiles, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors aprons etc, laid, bedded and pointed in any mortor complete all as specified and directed.

Material and Labourfor 18-20mm green marble as in flooring,staircase for treads including and over backing coat 15mm thick cement mortor 1:6 including pointing with wite cement using marble dust (1:2) with admixture of pigment to match with the shade of granite including semicircular nosing and all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

Material and Labour for cutting chases, pinning in brick masonary making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed.

Taking up or down steel tubing and connections 15mm dia bore, including cleaning for re-fixing or removal to store complete all as specified and directed. Note : Cutting chases and making good where required shall be measured and paid for separately.

Supply and fix 15mm dia bore GI tubing medium grade, galvanised with all fittings and fixed complete to walls and ceilings or laid in floor etc complete all as specified and directed.

Refixing old serviceable steel tubing obtain from taking down and connections 15 mm dia bore in new or old position (Walls, ceiling, floors, etc.)

Taking up or down steel tubing and connections 20mm dia bore, including cleaning for re-fixing or removal to store complete all as specified and directed.

Supply and fix 20mm dia bore GI tubing medium grade, galvanised with all fittings and fixed complete to walls and ceilings or laid in floor etc complete all as specified and directed.

Refixing old steel serviceable tubing obtained from taking down and connections 20 mm dia bore in new or old position (Walls, ceiling, floors, etc.)

Material and labour for cleaning of leaves, vegetation growth, debris and accumulated mud by washing brushing or by any means without hampering existing water proofing membrane (if provided) from permanent froof non accessible including cleaning of rain water pipes of building n. exc 1000sqm in any description and removing of debris/spoil from site and depositing the same to low laying area exc50m and n exc 250 m whereas directed by Engineer-in-Charge and specified.

Material and labour in repairs for applying one coat of hot blown bitumen 85/25 grade @ 1.2 kg/Sqm over the old membrane and applying two coats of aluminium paint @ 0.10 litres/Sqm in each coat complete all as specified and directed by Engineer-in- charge.

Sunil Constructions

S.K.HARAL

Rays Breakers

M/S.J.V.Datar

M/s S.R lahoti

Vipul Enterprises

Baljeet Singh Choudhari