SPECIAL REPAIR TO PLATFORM OF MAG NO 22 AT AMN SUB DEPOT AND PROVN OF GATE INFORNT OF CSD CANTEEN FOR MOVEMENT OF 15 MTS VEHS INSIDE/OUTSIDE PARADE GROUND WITH ROAD OF COD UNDER AGE B/R-II OF GE (EAST) JABALPUR

Amount

Surface excavation n.exc 30cm deep & averaging 15cm deep and getting out in soft / loose soil complete all as specified and directed.

Rough excavation n.exc 1.5m deep & getting out in hard /dense soil complete all as specified and directed.

Excavation over areas, n.exc 1.5m deep & getting out in soft / loose soil complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide & n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10sqm on plan & getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering & well ramming in layers n.exc 25 cm in any type of soil complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers n.exc 30 cm thick, watering, ramming/rolling and finishing to required size, shape, etc n.exc 1.5 m high from base complete all as specified and directed.

Removing excavated soil exc 50m but n.exc 100m & depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L for Maroom/red bajri filling in floors or pavings, laid in layers n.exc 15 cm thick spread, levelled & rammed including watering complete all as specified and directed.

Hard core, broken to gauge n.exc 63 mm complete all as specified and directed.

M&L PCC in foundations, filling and mass concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-2 using 40mm graded crushed stone aggregare in surface channels and drains complete all as specified and directed.

M&L for PCC in lintels upto 1.5 m clear span, cills, steps, seismic & other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating as directed type B-1 (1:2:4) using 20 mm graded crushed stone aggregate complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate set in CM (1:4) in landings, cover slabs (for manholes etc) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed.

M&L for RCC M-25 design mix using 20 mm graded crushed stone aggregate in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-25 design mix using 20 mm graded crushed stone aggregate in walls, retaining walls, basement walls and the like, any thickness, above top of footings, including attached pilasters and buttresses complete all as specified and directed.

M&L for RCC M-25 design mix using 20 mm graded crushed stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for RCC M-25 design mix using 20 mm graded crushed stone aggregate in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for 40mm Graded coarse aggregate as in filter media in layer near weep hole in retaining wall complete all as specified and directed.

M&L for Brick work with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for Boulder pitching grouted with cement and sand mortar 1:6, laid dry, hand packed tightly complete all as specified and directed.

Form work to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work, verticle or to batter rough finished surfaces of concrete flat complete all as specified and directed.

Form work to faces of walls, retaining walls, abutments, parapets & staircase railing and similar work including attached pillasters, buttresses, etc, vertical or to better Rough finished surfaces of concrete flat complete all as specified and directed.

Form work to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors & beams, etc rough finished surfaces of concrete flat complete all as specified and directed.

Form work to sides of pillars, posts, struts, piers,columns, and stanchions rough finished surfaces of concrete Square, rectangular or polygonal complete all as specified and directed.

S&F Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled & countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete & screwing etc wind ties for roof including securing bolts, posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting, etc & similar work conforming to Fe 290-0 Gde E-165 complete all as specified and directed.

S&F framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks & similar work conforming to Fe 290-0 Gde E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and directed.

M&L for Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and directed.

S&F Rolled mild steel Stairs (framed) including stringers, treades, landing, balusters, hand rails etc, including cleats, brackets, etc complete GDE Fe 410-0 or Fe 310-O complete all as specified and directed.

S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging, also fastening & fixing complete GDE Fe410-W (Gde E-250) Quality A complete all as specified and directed.

S&F Plain, galvanised, mild steel sheeting 1mm thick , in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

M&L for 100mm thick PCC1:3:6 type C-2 using 40mm graded crushed stone aggregate complete all as specified and directed.

M&L of 20mm thick wear proof topping as specified (incorporating an approved metallic floor hardner), finishing even and smooth without using extra cement (except matallic hardner) over 30mm thick granolithic concrete 1:1:2 floor topping laid over cement concrete sub floor etc and finished to an even and fair surface complete all as specified and directed.

S&F polythene film, black 50 micron laid in floors complete all as specified and directed.

Supply only metallic hardner of approved make complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 complete all as specified and directed.

Applying two coats of cement base paint, white or tinted over a coat of primer on new wall surface including preparation of surface complete all as specified and directed.

Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old surface complete all as specified and directed.

Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of red oxide, zinc chrome complete all as specified and directed.

Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, n.exc 10cm width or girth when unconnected with other painting or when painted in different tint, including preparation of new surface & applying one coat of red oxide, zinc chrome complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore as in weep hole complete all as specified and directed.

M&L for reinforced concrete pipes 600 mm dia, class NP-3, laid & jointed complete with collars complete all as specified and directed.

Rolling & consolidating formation surfaces in cutting by Power roller exc 8 tone & n.exc 12 tone complete all as specified and directed.

M&L for cement concrete work in pavement/hard-standing of flexural strength 40 kg/per Sqcm in field using 400 kg of cement per cubic metre, thickness of concrete 250 mm or less complete all as specified and directed.

M&L for forming 12mm thick Expansion joints filled with pre-formed bituminous filler & top 30mm primed & sealed with sealing compound, Grade `A' Thickness of concrete slab 200 mm complete all as specified and directed.

M&L for forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' complete all as specified and directed.

Demolition of Brick work or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles complete all as specified and directed.

Demolition of PCC of any description & in any position not otherwise specifically provided for (unreinforced) complete all as specified and directed.

Demolition of RCC of any description & in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed.

Removing building materials etc (other than spoil payable under items 03028 to 03031 in Section 3-Earthwork) to a distance of 100m or under, beyond the end included in the rates, including loading, unloading and stacking at the destination complete all as specified and directed.

Schedule of credit amount of Rs. 58,680.00 to be deducted during AOC

m/s R K SETHI