Addition/Alteration work at A Block PWD CEs office Jaipur Room No 213 (Supply of Remaining Furniture)

supply of office table of size 1800x900x750 mm with side unit 900x450x750 mm (structured made out of chemically treated pine board) The top of table made out of 19mm thick chemically treated pine commercial ISI board with 0.8 mm thick .sunmica top having both side one drawer 15" wide and 6"height on telescopic channels and one cupboard each side below drawers by 15" widead 18" widead. All necked edges should be covered with teak wood beading as per approved design with all fittings (It shluld have foor rest in fully length) The table top should be 38mm thick in edge extra 7.5 cm board on all edges with half roudn teak wood beading complete in all respect (Locked Key) including fine sprit polish as per direction of the Engineer in charge. (As per sample laying in furniture store)

Executive Chair (High Back Revolving) Supply of High back office revolving chair, chair with high back support chair, chair base made out with M.S. pipe chrome plated finish and chair moving at bottom with five nos. of twin castor wheel duly made with nylon plastic with injection molding process Chair back made out with net fabric and seat made out with medium density foam covered with fabric /net tapestry, chair having two nos. height adjustable arm made with PU base and fix at seat with the help of screw. Chair having seat adjustment gas lift function.

Supply of sofa set in 3 pieces with spring armed covered with approved tapestry cloth of @Rs. 550/- per mtr. The frame should be made out of cheer wood, Long piece should have 3 seater 5'3" long( excluding arms) and 4" thick P.U. foam of 32 density in seat and 18 nos. spring of size 5"x11 gauge and 50mm thick P.U. foam of 32 density in back. 2 nos side chair should be of same design/ shape/type of long piece having 9 nos. springs of size 6" x 10 gauge and 4" thick P.U. foam in seat of 6 nos springs of size 5" 11 gauge and 50mm thick P.U. foam in back. Total springs should be 75 nos. in all. Arms should have 25mm thick P.U. foam and the legs of sofa set should made out of 2.5" x2.5" wooden members. The arms rests should be covered with the foam and tapestry cloth as per approved sample/ drawing and design by the engineer in charge. (One 3 seater + 2 single seater is considered as one sofa set)

Supply of Canter Table overall size 18"x18"x22". The wooden frame with oriental style moulding on the frame. The legs will be carved out of teak wood members of out of size 21/2"x21/2" with horizontal members made out of size 3"x1" complete in all respect as per design and sample approved by Engineer-in-charge and client department.

Supplying and placing of Computer table Size 4'X2' and height 2'6''make 17 mm th. Plb wooden base Top and one side drawer,storage and key board, CPU,PUS Stand facility atteched. including cost of material and labour completed with all repect as per direction of Engineer incharge.

Supplying & Placing three seater airport sofa. The seat and back shall be made up of high quality cold rolled MS perforated sheet of 1.2mm thick, pressed and welded to form the shape. The seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. The armrest shall be made up of mild steel powder coated tube with 1.2mm thick. The base structure shall be supported by MS powder coated with 40-60µ (DFT). There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 440±10 mm(D) X 405±10 mm(H) from ground. Overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1675±10 mm.Including cost of material and labour completed with all repect as per direction of Engineer incharge.

Supplying and placing of wooden centre table(teak wood) 3'X2' With 10mm th. Glass top and Pu Dico/Melamine polish.Wooden structure are 2''X2'' square legs,1''X3'' Top and bottm cross wooden bars. including cost of material and labour completed with all repect as per direction of Engineer incharge.

Supply of peacock veneer moulded chair with continuous armrest having cushioned seat and back duly upholstery with approved quality tapestry cloth. The chair should be provided with duly inlay work done on it and fine finished melamine polish complete In all respect as per design and sample approved by engineer-in-charge.

Please Enable Macros to View BoQ information