SPECIAL REPAIRS TO BLDG NO. T-52 (Q STORE) AND T-71 (SUP PM STORE) OF 441 (I) SUP PI ASC AURANGABAD UNDER GE(S) AHMEDNAGAR

Amount

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings all as specified and as directed.

Taking down trusses etc. above 4 Mtr upto 8 Mtr for renewal of any defective members (timber renewed to be measured separately) and reassembling all as specified and as directed.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in all as specified and as directed. section, in any position all as specified and directed.

Demolition of brick/block work or stone boulder masonry built in cement mortar completed all as specified and as directed.

Dismantling of kota stone slab, interlocking blocks of any description in floor, laid, bedded & pointed in any mortar, all as specified and as directed.

Taking down cement or cement lime plaster on brick/stone walls etc. including racking out joints hacking for key scrubbing down with water etc etc complete all as specified and as directed.

Demolition cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness, (above or below ground level) all as specified and as directed.

Taking down of chowkats with shutter (without taking off shutter) not exc 1.50 Sqm each etc complete all as specified and as directed.

Taking down of chowkats with shutter (without taking off shutter) exc 1.50 Sqm but not exc 4 Sqm each etc complete all as specified and as directed.

S&F prepainted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified etc complete all as specified and as directed.

S&F prepainted galvatume aluminum zinc coating GI based plain steel sheets, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified etc complete all as specified and as directed.

S&F steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410 -W (Gde- E- 250) quality- A all as specified and as directed.

S&F steel work in rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates. Fe 410 -W (Gde- E- 250) quality- A all as specified and as directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161- 1979 grade St.-240 all as specified and as directed.

S&F rolled mild steel plates (plain or chequred) channels, square cut or notched, forming holes, with riveted, bolted or welded attachment confirming to Fe 410 - O or Fe 310 - O all as specified and as directed.

S&F mild steel wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and as directed.

S&F mild steel screw bolts of 15mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 10 cm long all as specified and as directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 cm mean radius in cement mortor 1:6 etc completed all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and fair without using extra cement etc complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement completed all as specified and as directed.

M&L for preparation of old plastered or unplastered decorated wall surfaces including cornices, pillars etc, and applying two coats of white wash complete all as specified and as directed.

M&L for preparation of old plastered or unplastered decorated wall surfaces and applying two coat of cement base paint complete all as specified and as directed.

M&L for preparing new plastered surface of walls and applying three coats of white wash completed all as specified and as directed.

M&L for preparation new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer etc completed all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

S&F framed work of Fe 410-W(Gde-E- 250) quality-A as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

S&F 1.25 mm thick mild steel plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required all as specified and as directed.

S&F for 35mm thick second class hardwood factory made plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F butt hinges, medium weight, cold rolled, mild steel, 100 mm size, ISI marked, complete all as specified and as directed.

S&F mild steel sliding door bolt 300 mm long, stove enamelled black with bright bolt not less than 16 mm dia with & including a minimum of 6 bolts & nuts four on bolt plate and two on staple plate complete all as specified and as directed.

S&F mild steel barrel tower bolts, 200 mm long stove enamelled black, with bright bolts complete all as specified and as directed.

S&F factory made steel windows with side hung shutter including projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F factory made steel windows with side hung shutter including projecting type hinges with steel handle, and steel peg stay complete without glazing bar with & including fixing flat iron for securing wire mesh complete all as specified and as directed.

S&F mild steel framed guard bars confirming to Fe-290-0 or Fe-330-0 welded to steel ventilators & windows etc complete all as specified and as directed.

S&F factory made steel ventilator with top hung shutter including hinges, steel peg stays etc complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F 3 mm thick sheet glass, ordinary quality & glazing with oil putty/ wooden beads in square not exc 0.50 Sqm each pane fixed to wooden, steel frames etc complete all as specified and as directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire & average width of aperature 1.18 mm, fixed with wooden beads / tinned tacks or galvanised wire staples to steel / wooden frame complete all as specified and as directed.

M&L for 75 mm thick PCC 1:4:8, type D2 (using 40 mm graded aggregate) as in sub-base complete all as specified and as directed.

M&L for precast cement concrete interlocking tiles (glossy finish/ rubber matt finish) of 60 mm thick, hydraulically pressed cemented tiles of grey colour with pigments, (glossy finish/ rubber mat finish) factory made, M-35 grade as in floor laid over & including 25 mm thick sand cushion including filling of interstices with fine sand complete all as specified and as directed. Note: Size, shape & pattern of tiles shall be as approved by GE.

S&F laminated gypsum tile board 8mm thick with textured white colour PVC film on the face side and metalized polyster (MPL) film on rear side in ceiling as per manufacturers instructions of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, including dismantling existing false ceiling work of any description all as specified and as as directed

Dismanlting floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviciable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed rendering in cement mortar 1:4 complete all as specified and as directed.

All as per serial item No 44 above but in dado / skirting or on vertical surfaces, laid over and including 10mm thick backing coat in cement mortar 1:4.

M&L for PCC (1:3:6) type C1 (using 20mm graded aggregate) as in coping cills, plinth courses, string courses, bed plates, kerbs etc complete all as specified and as directed.

M&L for 20-25mm thick machine cut kota stone slab flooring over 20mm thick cement screed base in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including round nosing at corners, rubbing and polishing complete all as specified and as directed

M&L for machine cut kota stone slab flooring 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including 20mm thick cement screed base in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including round nosing at corners, rubbing and polishing complete complete all as specified and as directed

Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or Power) complete including fittings such as switches, ceiling, regulator, sockets etc and removing materials to store for keeping in safe custody for credit and making good disturbed surfaces of walls, floors etc all as specified and as directed

M&L for point wiring (Light Point/fan Point) complete with 1.5 Sqmm single core ,multistranded ,copper conductor FRLS, PVC insulated and unsheathed cable 650/1100 volts grade, confirming to IS-694 1990, drawn through and including PVC cassing capping of size 25 mm /20 mm dia with all accessories as specified with modular cover plate with frame and modular metal flux boxes/rectangular PVC board for mounting fitting & fixtures like switches sockets and fan regulators etc including copper earth continuity wire for PVC insulated of size 1.5 Sqmm for one light Point controlled by one way switch complete all as specified and as directed.

All as per item No 50 but for 5 Amps socket in same board with 1.5 sq mm cable complete all as specified and as directed.

All as per item No 50 but for 5 Amps Socket in independent board with 1.5 Sqmm cable complete all as specified and as directed.

All as per item No 50 above but for power point 3 pin switch socket 15 Amp with PVC copper conductor cable multistrand unsheathed 2.5 Sqmm on independent board including one run 1.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and capping fixed on wall including PVC box 2 mm complete all as specified and as directed.

S&F modular switch, single pole one way 6/10 Amps 1 module complete all as specified and as directed.

S&F modular switch, single pole one way 16 Amps 1 module complete all as specified and as directed.

S&F modular socket, 6 amp-2/3 pin combined 2 module complete all as specified and as directed .

S&F modular socket, 6 A/16 amp -2/3 pin combined 2 module complete all as specified and as directed.

S&F ceiling rose, surface bakelite three terminal type complete all as specified and as directed.

S&F modular fan regulator step type, 120W-2 module complete all as specified and as directed.

S&F in replacement decorative ultra slim square/round profile LED lighting fixture with extruded polycarbonate, environmental friendly , energy efficient of capacity 20/22 Watt 6500 K with inbuilt driver complete fitting and all other accessories fitting arrangements complete all as specified and as directed.

S&F in replacement 35/40 Watt building mounted LED security light fitting complete made up of pressure die cast housing with toughned glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07 & 10KV external SPD, including GI bracket made out of GI pipe 40/50 mm bore, medium grade pipe 1.2 m long bend to shape required fixed to pole / wall with 02 Nos MS clamps made out of flat iron 40 x 5 mm including nuts, bolts and washer, painting with two coats aluminium paint over a coat of primer, suitable for LED fitting, complete all as specified and as directed.

S&F in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

S&F in replacement of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp 240 Volts complete all as specified and as directed.

S&F in replacement, MCB DB double door 4 way TPN with suitable rated busbar 415 V complete all as specified and as directed.

S&F in replacement, MCB DB double door 4 way SPN with suitable rated busbar 240 V complete all as specified and as directed.

S&F in replacement, 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and as directed.

S&F in replacement, MCB SPN 240 volts 4 to 63 Amps "C" curve complete all as specified and as directed.

S&F in replacement MCB single pole 240 volts 6 to 32 Amps "C" curve complete all as specified and as directed.

M&L for sub main wiring with 2 runs of 4.0 sqmm, single core, PVC insulated & unsheathed cable, conforming to IS-694, 1100 volts with copper conductor, multi stranded, drawn in and including suitable size PVC cassing capping (ISI marked) with all accessories such as Tees, Elbows, Junction box etc as requied alongwith one run of 4.0 sqmm single core PVC insulated & unsheathed copper conductor as continuous earth wire dolly and connecting to existing main switch board / distribution board of each building as ordered and testing on completion including taking down old submain wiring and any type of casing/caping/conduit, complete all as specified and as directed. Note : Two runs of 4.0 Sqmm cable, one run of 4.0 Sqmm cable and one run of PVC casing/caping shall be measured as one unit.

M&L for sub main wiring with 2 runs of 2.5 sqmm, single core, PVC insulated & unsheathed cable, conforming to IS-694, 1100 volts with copper conductor, multi stranded, drawn in and including suitable size PVC Cassing Capping (ISI marked) with all accessories such as Tees, Elbows, Junction box etc as requied alongwith one run of 2.5 sqmm single core PVC insulated & unsheathed copper conductor as continuous earth wire dolly and connecting to existing main switch board / distribution board of each building as ordered and testing on completion including taking down old submain wiring and any type of casing/caping/Conduit, complete all as specified and as directed. Note : Two runs of 2.5 Sqmm cable, one run of 2.5 Sqmm cable and one run of PVC casing/caping shall be measured as one unit.

Supply, laying, jointing in replacement and testing PVC XLPE insulated armored heavy duty electric cable with aluminum conductor, 1100 volt grade, cross sectional area 35 Sqmm 3.5 Core laid in trenches/ on wall complete all as specified and as directed.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for foundations/laying of cables etc and getting out in soft/loose soil all as specified and as directed.

Returning, filling in including spreading levelling watering and well ramming in layer not exceeding 25 cm thick in any type of soil complete all as directed.

Removal of surplus exavated material to a distance not exc 50mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point in any type of soil complete all as specified and as directed.

M&L for double walled corrugated DWC HDPE pipe of outer dia 50mm and internal dia 38mm including 90 degree bends with coupler and rubber ring laid in trenches of size 50 mm suitable for cable protection of size 2 core, 10 sqmm to 3.5 core 70 Sqmm all as specified and as directed

S&F in replacement, GI tubing light grade of 40 mm dia for cable protection on pole/wall/floor/ or in trenches and drain etc complete with necessary clamp, nut, bolts and washers and socket and making good the disturbed surface of wall, floor or roof etc all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode, 60cm x 60cm x 6.0 mm thick, burried directly in ground (earth pit not less than 2.25metre deep below normal ground level) with top edge of earth plate not less than 1.5 metre below normal ground level, connected to and including galvanised earth lead wire of 4 mm dia from earth pit to each qtr DB by means of nuts & bolts, check nuts and washers of galvanised including PCC pit of 1:2:4, type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, mild steel angle iron 25 x 25 x 3mm in frame, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate no 3 of MES sch 2009 (Part I), including taking up/down old earthing connected to main switch board all as specified and testing on completion.

HG PATHAN CONSTRUCTION COMPANY (BID ID -3086750)

M/s.M G Kulkarni (BID ID -3075830)

M/S Tirupati Goroba Shendge (BID ID -3085900)

ASHWAMEDH ENGINEERS (BID ID -3082401)

M/s S.R lahoti (BID ID -3085288)

D V Engineers and Contractors Pvt Ltd (BID ID -3084354)

M/s kishor M Lalwani (BID ID -3080091)

SONU ENTERPRISES (BID ID -3086374)

M/S. M.A. Sharief engineers and contractors (BID ID -3087759)

B.R.ANAND (BID ID -3085881)