Construction of Treasury Building cum Residential accomdation at Nalagarh Distt Solan HP

Amount

Excavation in foundations, trenches etc. in all kinds of earth work including spade work, pick work, jumper work blasting work including where blasting is prohibited and chiselling / wedging out of rock and their intermediate classification of soil including dewatering whereever required upto all leads and lifts and stacking the excavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15 cm. layer when required into plinths, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus.

Pick/juper work 50% each

Pick jumper work.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete including carriage of material in all leads and lifts.

Providing form work with steel plates 3.15mm(three point one five millimetre) thick welded with angle iron in frame 30x30x5mm ,so as to give a fair finish including centring ,shuttering ,strutting and propping etc. with wooden battens and ballies , height of propping and centring below supporting floor to ceiling up to all heights and removal of the same for insitu-reinforced concrete & plain concrete work in:

Foundation footing and basis of columns, etc. and mass concrete.

Columns, pillars, posts and struts :-

Square rectangular or polygonal in plan

Beams, cantilever, girders and lintels :-

Sides and soffits of beams, beam haunching cantilevers, brssumers and lintels not exceeding 1 metre in depth in all heights from floor

Flat surfaces such as soffits of suspended floors, roofs, landings and the like :-

Floor etc. upto 200mm in thickness

Edges of slabs and break in floors and walls :-

Under 20cm wide :-

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

Applying a coat of hot bitumen (mexphalt 80/100 or equivalent) using 1.70 kg. per square metre on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil.

Providing and laying damp proof course 38mm thick with cement concrete 1:2:4 (1 cement:2 sand:4 stone aggregate 12.5mm nominal size) and curing complete.

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 graded stone aggregate40 mm nominal size) and curing complete excluding cost of centring and shuttering but including carriage of materials in all leads and lifts :-

Foundations and plinth

Providing and laying cement concrete 1:8:16 (1 cement: 8 sand:16 graded stone aggregate 20mm. nominal size) and curing complete on slab and floor excluding the cost of form work. screed laid under flooring

Providing and laying cement concrete work 1:1½.:3 (1 cement : 1½. sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed and vibrated for compacting concrete and curing complete excluding cost of form work and reinforcement for reinforce cement concrete including carriage of materials in all leads and lifts.

Foundation footings, bases of columns and the like and mass

Providing and laying cement concrete work 1:1½.:3 (1 cement : 1½. sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed and vibrated for compacting concrete and curing complete excluding cost of form work and reinforcement for reinforce cement concrete including carriage of materials in all leads and lifts.

Columns, pillars, posts and struts :-

Providing and laying cement concrete work 1:1½.:3 (1 cement : 1½. sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed and vibrated for compacting concrete and curing complete excluding cost of form work and reinforcement for reinforce cement concrete including carriage of materials in all leads and lifts.

Vertical surfaces such as walls of any thickness but not less than 0.1 mtrattached pilasters,buttresses, plinth and string courses etc.

suspended floor roofs, landing and shelves, balconies, beams, girders

Providing and laying cement concrete 1:2:4 (1 cement:2 sand:4 graded stone aggregate 20mm nominal size) and curing complete size) andcuring complete excludin cost of form work in:

Moulding as in cornices, window cills not exceeding 15 cm.In girth :

a) upto floor two level :

Providing and laying cement concrete work 1:2:4 (1 Cement:2 Sand:4 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in :

Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses,plinth and string courses etc. from top of foundation upto floor two level :

Providing mild steel/Tor steel reinforcement including cost of binding wire for R.C.C. work including bending, binding and placing in position complete upto all floor level heights including carriage of material in all leads and lifts :-

Tor steel

Second class brick work using common burnt clay building bricks in superstructure above plinth level upto all floor levels in cement mortar 1:5 (1 cement : 5 sand) including carriage of material in all leads and lifts :-

Second class half brick work using common burnt clay building bricks in foundation & plinth in cement mortar 1:4 (1 cement : 4 sand) including carriage of material in all leads and lifts :-

Second class half brick work using common burnt clay building bricks in super structure in cement mortar 1:4 (1 cement : 4 sand) including carriage of material in all leads and lifts :-

Brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6 (2nd Class Brick)

Half Brick masonry in common burnt clay building brick in foundation and plinth in cement mortar 1:4 (1 cement:4 sand)

Boulder filling tightly hand packed under floor including watering, ramming, consolidating etc. complete including carriage of material in all leads and lifts

Providing and fixing windows and ventilators frames of channel section size 75x40 mm ( seventy fivein to forty milimeters) for end frame and for centre frame channel section frame 75x40 mm ( seventy five by forty milimeters) with mild steel flat 75x4 mm ( seventy five into for milimeters) in combination welded togather to make one frame including hinges jamb lock jamb,beed and if reuired angle threshold of mild steel angle of section 50X25 mm or base ties of 1.25 mm pressed mild steel welded or regidly fixed together by mechanical means,adjustable lugs with split end tails to each jamb including steel but things 2.5 mm thick with guards,lock strike plate and shock absorber as specified and applying a coat of approved steel primer after pretreetment of the surface as directed by Engineer-inCharge

Providing and fixing windows and ventilators frames of channel section size 75x40 mm ( seventy fivein to forty milimeters) for end frame and for centre frame channel section frame 75x40 mm ( seventy five by forty milimeters) with mild steel flat 75x4 mm ( seventy five into for milimeters) in combination welded togather to make one frame with making steel square section with mild steel section 20x4 mm( twenty by for milimeters) and 12x4 mm( tweleve into for milimeters), shutters of rolled section F-7(Seven)B section including glass panes of 4 mm (Four millmetres)thick in glazed panel and wire gauge of designation 85 ( eighty five)with 0.56 mm ( Zero point five six millmetres) dia in wire gauge panel and fixed glazing with angle iron and T section of 25x25x3 mm ( twenty five in to twenty five in to three millmetres) and flat of 12x4 mm (twelve in to four millmetres) in sash bar duly welded at corner and joints of all stenty five by teel sections, embedded in cement concrete block 10*10*10 (fifteen in to ten in to ten) centimetress size in 1:3:6 (one cement: three sansd : six graded hard stone aggregate twenty miimeters nominal size)or wooden plug screws or rawl plug screwsand fixing clips or with bolts and nutsas required and fitting including fixing glass with gasket clipsand special materialsash putty as per the direction of the Engineer-In- Charge,as per HP.PWD.specification 1990 volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges

Providing and fixing angle iron cupboard frames manufactured fromM.S.Angle iron section 25X25X5mm thickness including hingesjamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm welded or rigidly fixed bymechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in-Charge.

Providing and fixing flush door shutters interior grade, commercialtype, core of black-board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands and face veneers on both faces of shutters.

35 mm thick including black enamelled M.S. butt hinges.

P/F panelled wire gauge shutters using galvanized MS wire gauge of IS gauge designation 85 g with wire of dia 0.56 mm for doors, windows and clestory window i/c black enamalled iron butt hinges with necessary screws 40 mm thick ist class deodar wood.

Providing and fixing 19 mm thick commercial board water proof boards in shelves, box for cup boards including fixing with nickel plated piano hinges with screws etc. complete including carriage of material in all leads and lifts

Providing and fixing 19 mm thick commercial board water proof shutter for cup boards including fixing with nickel plated piano hinges with screws etc. complete including carriage of material in all leads and lifts

Providing and fixing aluminium sliding bolts (Barrel type) anodized transparent or dyed to required shade and colour with bolts and nuts etc. complete including carriage of materials in all leads and lifts:-

Providing and fixing aluminium tower bolts (Berrel type) anodized transparent or dyed to required shade and colour with screws etc. complete including carriage of materials in all leads and lifts:-

Providing and fixing aluminium handles anodized transparent or dyed to required colour or shade with necessary screws etc. complete including carriage of materials in all leads and lifts :-

Providing and fixing oxidized M.S. double acting spring hinges with necessary screws.

Providing & fixing 100 mm bright finished brass door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of materials in all leads and lifts :-

Providing & fixing bright finished brass 100 mm mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (Indian Make of approved quality) including carriage of materials in all leads and lifts :-

Providing & fixing 50 mm bright finished brass cup board or ward robe knob with necessary screws including carriage of materials in all leads and lifts :-

Providing and fixing bright finished brass ball catcher 10 mm dia

Providing and fixing 12 mm thick and 100 mm wide palmet with 25 mm dia wooden curtain rod and brackets including fixing with 23x3 mm MS flat 10 cm long and plug etc. in 1st class deodar wood.

6mm cement plaster to ceiling in cement mortar 1:3 (1 cement : 3 sand) including carriage of materials within all leads and lifts in all floor levels including carriage of materials within allleads and lifts :-

15mm thick plain cement mortar bands in cement mortar 1:4(1 Cement:4 Sand)upto 300 mm in width.

Raised band

15mm Cement plaster in two coats,backing coat 15mm and finishing coat 5mm thick on rough side of brick/stone masonry walls for interior plastering upto floor two level mm in girth and finished even and smooth.exceeding 80 rounded angles,chamfers and/or rounded angles not including arrises,internal IN Cement mortar 1:4

15mm cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 30cm in girth and finished even and sand opapered smooth including carriage of materials within allleads and lifts..

Cement mortar 1:5(1 cement :5 sand)

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 30cm in girth and finished even and smooth including carriage of materials within allleads and lifts.

Cement mortar 1:5(1 cement :5 sand)

Cement concrete flooring 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) laid in one year finished with a floating coat of neat cement including carriage of materials within all leads and lifts:- 40mm thick

Providing and laying 25 mm (Twenty five milimetre) thick pre polished Kota stone slab flooring with 20mm (twenty milimetre ) thick base of cement mortor 1:4 (one cement is to four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Marble work (table rubbed and polished) in steps,jambs,walls,pillars and other plain work in cement mortar 1:2 (1white cement:2 marble dust) with an admixture of pigment to match the marble shade :

White makrana marble

Kota stone slab flooring 20 mm (average) in riser of steps thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete

30 mm thick

Kota stone slab flooring 20 mm (average) thick base of ement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete

Providing and laying Duro stone vetrified tiles (300x300mmx10mm) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment ofrequired shade to match the shade of tiles complete

Providing and laying Duro stone vetrified tiles (300x300mmx8mm) in grey/coloured of required shade in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.

Providing and laying spartic ceremic tiles 5.5mm thick in flooring 300x300mm size treads of steps laid on a bed of 12mm thick cement mortor 1:3 ( 1cement:3sand ) flushed with pointing in white cement.

Kota stone slab flooring 20 mm (average) thick base of ement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete

25 mm thick

Providing and laying red sand stone slab flooring 40mm average thick on 20mm average thick base of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab i/c rubbing and granite polish finish complete

Providing and laying tectile tile of approved shade in flooring, treads of steps and landing with coving laid on a bed of 12mm (Twelve mlimetres) thick cement mortar 1:3 (One cement: Three sand) finished with flush pointing in white cement as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

White glazed tiles 6mm thick in skirting risers of steps and dado on 12mm thick cement mortar 1:3 (1cement : 3sand) and jointing with neat cement slurry including carriage of material in all leads and liftrs :

Making half round nosing to Kota stone/granite stone/ marble complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Marble work (table rubbed and polished for walls lining) Veneer work 2.50cm. thick in cement mortar 1:3 (1 cement:3 sand) including pointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with an admixture of pigment to match the marble shade :

Baroda Green Marble

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Applying priming coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering as required with :-

Readymixed primer

Painting two coats (excluding priming coat) with enamel paint of approved design or its equalent on undecorated wall surfaces to give an even shade including cleaning the surface of all dirt,dust and sand papered smooth to give final finish to the surface complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Distempering (two coats) with synthetic/acrylic washable emulsion of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropppings and other foreign matter and also including preparing the surface even and sand papered smooth as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including and paper smooth complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter including carriage of materials within all leads and lifts.

Enamel paint other then white :-

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand papering complete including carriage of materials within all leads and lifts :

With ready mixed priming paint brushing red lead, red oxide / zinc oxide chrome.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting including carriage of materials within all leads and lifts :

Ready mixed paint brushing wood primer pink :-

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering and stopping including carriage of materials within allleads and lifts.

With enamel paint other than white paint :-

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick / stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size)

Providing and fixing moulded hand rail of M.S. hollow pipe 50mm dia welded in straight lenght over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be mesaured & paid separetely.

Providing and fixing M.S. grills of required pattern in wooden / PVC frames of windows etc. with M.S. flats square or round bars with rounded headed bolts and nuts or by screws including carriage of material in all leads and lifts Plain grill.

Steel work welded in built up sections, trusses and framed work, including cutting hoisting fixing in position and applying a priming coat of red lead paint including carriage of materials within all leads and lifts :-In gratings, framed, guards, bars ladders and railing, brackets and similar works :-

Providing and fixing in position collapsible steel shutters with vertical channels 20mmx10mmx2mm(twenty into ten into two millimeter) and braced with flat iron diagonals 20mmx5mm(twenty into five millimeter)size with top and bottom rails of T-iron 40mm x 40mm x 6mm (forty into forty into six millimeter) with 38mm (thirty eight millimeter)dia steel pulley complete with bolts and nuts locking arrangements, stoppers, handles, including aplying a priming coat of red lead paint as per HP.PWD. specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One),including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including all incidental charges and as per direction of engineer in charge.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete.

150 mm dia pipe

Providing and fixing m.s.holder bat clamps of approved design to C.I. or S.C.I pipes embeded in and including cement concrete blocks 10 x10x10 cm of 1:2:4:mix (1 cement 2sand 4 stone graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good thewall etc.

150 mm dianetre for C.I.pipe

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete

PVC Plain bend 150mm dia

PVC shoe 150mm dia

P/L water proof treatment with Dr.Fixit FAST FLEX or equalent with two component polymer modified cementitious coating consisting of cementitous powder and polymer FLEX by maintaining acoverage of 6-7 sft/kg to achieve 1 mm thickness Clean and saturate surface and then applying acoat of Dr. Fixit-FASTliquid in two coats. For first coat:-The second coat shall be applied in opposite direction after four six hours of application of 1st coat. Then sprinkle sand on top of surface of applied Dr.Fixit FAST FLEX while still tacky over the second coat Then cement mortar of cement:sand (1:4) admixed with 200 ml of pidiproof LW @ 200 ml /50 kg bag of cement over the floor with the suitable gradient towards the drain pipe, while the second coat of Dr. fixit is still tacky.

Providing and fixing 100 mm dia MS pipe embeded in cement concrete block 30x30x30 cm( thirty in to thirty in to thirty centimetres) 1:2:4 ( one cement : twosand :4 aggregate twenty millmetres nominal size) complere a sper drawing including preparation of ground including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing SURAXA Model -SRD-"C" -Class ( with Grill) as per IS: 11188;1991 strong room door of 2225 H x 1270 (7.3 Ft x 4.16 ft W outer dimensions and 2000 H x 915 W ( 6.5x2.5 ft) clear opening with overall thickness including grill 265 mm, L-Type construction with 10 mm MS sheet, front door 10 mm sheet Armored with 65 mm double duty barrier fire proof and burglary resistance, drill defeat shield around the locking mechanism 10- lever daul control high precision locks two units weight with PU door finish weighing 950 kgcomplete as per specifications including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing ACP tiles in ceiling of size 600x600 mm of approved shade and pattern including moulded on powder coated G.I. frame work fixed/hanging with wall or ceiling etc. with specified clamp and G.I. wire rawl plug etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing dome shaped grating of MS flat 25x5/6 mm square or round shape with 6 mm dia bars in dome complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

P/F PE-AL-PE composite pressure pipe UV stablized with carbon black cofirming to IS -15450-2004 water supply including clamp at one meter spacing, cuuting fixing and making good the wall etc.but excluding the cost of fittings pipesexposed on walls.

1620 (20 mm OD pipe)

2025 (25 mm OD pipe)

P/F composite end seal compression fitting as per IS-15450-2004 for cold supply e.i. tees, elbows, reducers, connectors, couplers, and clamps, with jointing testing and fitting complete including cutting and making good the walls etc.

Equal Tees

Reducing Tees

1620 in all branches

2025 in all branches

Female branch tee

1620x1620x20 mm thread

2025x2025x25 mm thread

Female elbow

1620x20 mm thread

2025x25 mm thread

Male threader connector

1620x20 mm thread

2025x25 mm thread

Female threader connector

1620x20 mm thread

2025x25 mm thread

Couplers

Reducers

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of materials within all leads and lifts

Providing and placing PVC water storage tank makeof ISI:12701 marked with necessary fittings including overflow pipe and scour pipes etc. and ball valve with cover and locking arrangement including providing pads of required sizes for inlet and outlet etc.

1000 liters

2000 liters

Providing and fixing PVC soil, waste and ventilating pipes and jointing complete

75 mm (one hundred millimeter) nominal bore

110 mm (one hundred fifty mm) nominal bore

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive complete

75 mm (one hundred millimeter) nominal bore

110 mm (one hundred fifty mm) nominal bore

Providing and fixing PVC collars ISI marked including fixing with approved adhesive complete

75 mm (one hundred millimeter) nominal bore (A.R.)

110 mm (one hundred fifty mm) nominal bore

Providing and fixing PVC single equal branch ISI marked including fixing with approved adhesive complete

75 mm (one hundred millimeter) nominal bore (A.R.)

110 mm (one hundred fifty mm) nominal bore

Providing and fixing cast iron cowl 75 mm dia.

Providing & Fixing MS stay and clamps for PVC pipes:-

110 mm (one hundred fifty mm) nominal bore

75 mm (one hundred fifty mm) nominal bore

Providing & fixing 100mm (hundred mm) dia PVC floor trap of self cleaning design i/c cutting and making good the walls and floors:-

Providing and laying brick (one size) 50 mm crushed aggregate.

Providing and fixing PVC vent pipe for cowl I.S.I marked including cutting holes in walls and making good the same, as per HP.PWD.specification,including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges

Providing & fixing vitreous china closet squatting pan (Indian type WC pan size 580mm (five hundred eighty mm) (earth work bed concrete and trap to be measured and paid for separately)

Orrissa Patteren

Providing and fixing vitreous china wash down water closet (European type WC pan) with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement : one sand) (seat and cover to be measured and paid for separately)

Anglo Indian (Universal closet)

Providing and fixing 100 mm size P or S trap for water closet squatting pan including jointing the trap with soil pipe with approved quality adhesive including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. .

Providing & fixing 12.5 (twelve point five) liters low level flushing cistern with pair of CI or MS brackets complete with fittings such as lead valve less siphon 15mm (fifteen mm) nominal bore brass ball valve with polythene float CP brass handle union and coupling for connection with inlet outlet and overflow pipes 40mm (forty mm) dia CP flush bend with cistern and closet (over flow pipe to be measured and paed separately)

Providing and fixing plastic seat (solid/ hollow type) and cover for wash down water closet with CP brass hinges and rubber buffers:-

White plastic seat & cover

Providing & fixing vitreous china wash basin Flat back (white shade) with double hole for pillars with CI or MS brackets painted white including cutting holes and making good the same but excluding fixings:-

Providing and fixing vitreous China pedastal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 810x450 mmx200 mm stainless steel kitchen sink of approved standard ISI made with drain board and C.P. waste with C.I. Or M.S. bracket painted white including cutting holes and making good the same but excluding fittings complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. .

Providing and fixing 460x385x200 mms tainless steel kitchen sink of approved standard ISI made C.P. waste with C.I. Or M.S. bracket painted white including cutting holes and making good the same but excluding fittings complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. .

P/F viterious china 42x39x63 cm flat back bowl pattern Urinal including connection with waste pipe by means of white lesd mixed with chopped hemp ( waste pipe to be paid separately)

Providing & fixing 32mm (thirty two mm) dia rubber plug for sink or wash basin.

Providing & fixing dia MI union for wash basin or sink.

32mm dia

P/F CP Bottle trap for wash basin and sinks.

32 mm dia

Providing & fixing 32 mm dia CP brass waste for wash basin of sink.

Providing & fixing 600 x 450mm (six hundred into four hundred fifty mm) beveled edge mirror of superior class mounted on 6mm thick AC sheet of plywood sheet fixed with wooden plugs with CP brass screws and washers complete.as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 600mm x 20mm C.P. brass towel rail complete with C.P. brass brackets fixed to wooden pluges with C.P. brass screws as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing vitreous china soap tray recessed soap tray 150x150 mm size as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing CP brass toilet paper holders as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing chromium plated heavy duty brass soap dish with CP brass brackets fixed to wooden cleats with CP brass screws.

Providing & fixing CP brass bib tap with capstan head:-

20 mm dia

Providing & fixing CP brass pillar tap with capstan head:-

20 mm dia

P/F CP brass angle valve15 mm without nut and pipe

Providing & fixing stop cock:-

20 mm dia

P/F PVC connection pipe with brass union 45 cm long:-

20 mm nominal bore

P/F 20 mm bore CP brass full way valve

Constructing brick masonry chamber for under ground C.I. inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 ( 1 cement: 5 sand) C.I. cover with frame (light duty) 355 mm x610mm internal dia mansions total weight of cover with frame to be not less than 38 kg ( weight of a cover 23 kg. and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix ( 1 cement: 2 sand: 4 graded stone aggregate 20mm nominal size) foundation concrete 1:5:10 (1 cement : 5 sand: 10 graded stone aggregate 40mm nominal size) inside plaster 15mm thick with cement mortar 1:3 ( 1cement: 3 sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete

inside dimensions 455mm x 610 mm X 450mm deep single pipe line.

Providing & fixing CI inlet connection for flush pipe with WC pan

Providing and fixing CP brass grab bar 40 mm( Forty millmetres) diametre steel pipenat 78 (seventy eight) centimeter height with MS (mild steel) plate as per detail as the position of seat and wash basin complete as per Aerchitect drawing including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing PTMT jet spray of approved quality and colour with 1,0 mtr length as per Aerchitect drawing including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 15 (fifteen) millmetress nominal bore mixer for kitchen sink with top/bottom swinging spout as per HP.PWD specification , including carriage of all labour equipment and material to various location through all modes of transportation in all leads, lifts and all incidental charges.

Providing and fixing 5.0 capacity white P.V.C low level dual flushing cistern of Pryag or equalent with a pair of G.I or mild steel brackets complete with required necessary fittings such as lead valve, less siphon 15mm(Fifteen millimeters) nominal size brass valve polythylen float, C.P brass handle union and coupling for connection with inlet, outlet and over flow pipe, 40mm(forty millimeters) diameter C.P flush bend including cutting holes in wall and making good the same and connecting the flush bend with cistern and closet complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

P/F PTMT waste coupling of approved quality and colour 32 mm bore including carriage of all labour equipment and material to various location through all modes of transportation in all leads, lifts and all incidental charges.

Providing and fixing PTMT Grating 100 mm nominal size of approved quality and colour as per Aerchitect drawing including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all inc

Providing and fixing PTMT urinal cock 15 mm nominal size of approved quality and colour as per Aerchitect drawing including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all inc

Earthwork in excavation for structure as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 mtr, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil up to 3 mtr depth

Providing concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification Clause 802,803, 1202& 103 P.C.C. Grade M 10 (1-3-6)

Providing and laying filter media with granular crushed aggregate as per specification to thickness of not less then 600 mm with smaller size towards the soil and bigger size towards the walls and providing over the entire surface behind abutment, wing wall, retaining walls to the full height, completed to firm condition complete as per drawing and technical specification clause 1204.3.8.

Providing weep holes in brick masonry /stone masonry plain/ reinforced concrete abutment, wing wall, Retaining wall with 100 mm dais PVC. pipe expending through the full width of the structures with slopes of 1 (V):20 (H) towards drawing face complete as per drawing and technical specification clause 614,709,1204, 3.7.

Himanshu Kumar

dharamvir singh govt. contractor

ranjit singh

SURJEET SINGH CONTRACTOR

JAI PRAKASH RANOTE