8540 REPAIR TO MAINT WORKS IN ORs, JCOs MD ACCN AND OTM BLDGS IN AFMC AND SOUTH CAMPUS OF AFMC UNDER GE (CENTRAL) PUNE

Amount

Taking down chowkats or frames with shutter (without taking off shutter from the frames) n. exc 1.50 Sqm each with and including including making good the disturbed surfaces as original with CM (1:6) or PCC (1:2:4) type B0 complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc 1.50 Sqm but not exc 4 Sqm each with and including making good the disturbed surfaces as original with CM (1:6) or PCC (1:2:4) type B0 complete all as specified and as directed.

Taking down shutters of any description, exc 1sq.m and n.exc 2 sq.m each and removal from site etc complete all as specified and directed.

S&F pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed. Note :- Rates quoted deemed to include S&F of hinges, lugs, lock strike plate.

S&F pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed. Note :- Rates quoted deemed to include S&F of hinges, lugs, lock strike plate.

M&L for PCC 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in steel chowkhats, hold fasts and bed blocks etc including necessary form work complete all as specified and directed.

S&F 30mm thick flush shutters, solid core onstruction, with particle board core and plywood face panels, commercial type on both sides, one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed

Supply and fixing (factory Made) 2nd class hard wood 35 mm thick glazed and skelton shutters open rebated and prepared to receive gauge. (With sash bars ) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24 (a) supplied and fitted to chowkats complete all as specified.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing as per specifications and drawing complete all as specified and directed.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work in (any colour) for Sliding window Three track made of extruded profiles. Window profile with hollow section with multi chamber. Frame / shutter, sliding sash, sliding mesh Sash, sliding interlock (One vertical length in each shutter), Glazing bead will be mitred cut at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of window section /hardware by using modern technique with and including EPDM gasket, steel roller system, touch Lock of zinc alloyed of same colour of window powder coated and other required materials/ accessories will be provided for creation to window and frame will be fixed to the any type wall by using fasteners / screws of required dia and size complete all as specified and as per directions of Engineer-in-Charge. Note: The unit rate quoted by contractor excludes cost of glass and wire mesh and includes all other connected accessories. Before creation of window, the sample of all materials / accessories / hardware will be submitted to Engr-in-Charge for weighing of powder coated window section and approval of materials / accessories / hardware.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and as per directions of Engineer-in-Charge. Note: The unit rate quoted by contractor excludes cost of glass and wire mesh and includes all other connected accessories. Before creation of doors, windows, ventilators and partitions (Fixed portions), the sample of all materials / accessories / hardware will be submitted to Engr-in-Charge for weighing of powder coated window section and approval of materials / accessories / hardware.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, door chowkats of angle or other section and similar works complete of Gde Fe-290 Gde E-165 including welding etc.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples with and including complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing fixed to aluminium window / ventilator shutters etc complete all as specified and directed.

S&F figured / frosted glass 4.00 mm thick, pin head type and glazing with oil putty & necessary screwing / cliping in squares/rectangle exc 0.5 Sqm in each pane complete all as specified and as directed and directed.

M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted wooden or wood based surfaces of any description, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new or previously untreated steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F stainless steel butt hinges medium weight of size 100 mm fixed with stainless screws complete all as specified and directed.

S&F stainless steel 300 mm long aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts complete all as specified and directed.

S&F 200mm size stainless steel, barrel tower bolt of extruded section complete all as specified and directed.

S&F stainless steel handles 150 mm long fabricated type anodised complete all as specified and directed.

S&F 100mm long stainless steel floor door stopper double legged with rubber shoe, fixed to bottom rail of door complete all as specified and directed.

S&F mild steel 300mm, ordinary rat rail rod pattern springs, including roller and roller plate complete all as specified and directed.

S&F in repairs harrison rails (Curtain rod/drapery rod), 20mm dia, stainless steel with and including fency type stainless bracket / wall to wall 02 Nos of each opening and stainless steel side stopper fency type of required shape and size 2 Nos of each opening complete all as specified and directed.

M&L for precast concrete solid block masonry exc 10cm width with solid block of PCC (1:5:8) Gde C-5 and setting in CM 1:6 with and including Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed..

M&L for rendering 10 mm thick in CM 1:6 on fair face of brick /concrete / stone surfaces of any description and finishing the surfaces even and smooth with a thin layer of sogal finish in patches with and including taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 in two layers, 5mm thick in CM (1:4) over a coat of 10mm thick in CM (1:4) when surface of green and finishing with and including mixing of liquid WPC of approved make @ 200ml per bag of cement / manufacturer's instructions on brick/concrete wall surfaces of any description, and finishing the surfaces even and fair with and including taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer of same make over 2mm thick wall care putty complete all as specified and directed.

M&L for preparing old plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer of same make over 2mm thick wall care putty with and including complete removal of existing treatment of any layer of wall complete all as specified and directed.

M&L for preparing new plastered or unplastered surface of walls and applying two coats of cement based paint over a coat of cement base primer complete all as specified and directed.

M&L for preparing old plastered or unplastered surface of walls and applying one coat of cement based paint complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L for 75mm thick (1:4:8) Type-D2 (using 40mm graded crushed stone aggregate) as in levelling course / sub base of flooring complete all as specified and directed.

M&L for 25mm thick (1:2:4) Type-B-0 (using 12.5mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and directed.

M&L for non skid coloured designer ceramic tiles 10mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15mm thick screed bed in CM (1:4) compete all as specified and directed.

-ditto- all as per item No.38 above but on skirting over with and including 10mm thick backing coat in CM 1:3 complete all as specified and directed.

M&L for non skid ceramic tiles coloured pattern as required of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15mm thick screed bed in CM (1:4) compete all as specified and directed.

M&L for glazed ceramic coloured, designer & pattern (dark & light shade combination) tiles in 450 x 300 x 7-8 mm thick on vertical surfaces such as dado etc set and jointed in neat cement slurry and pointed in white or colour cement to match over with and including 10mm thick backing coat in CM 1:3 and d complete all as specified and directed.

M&L for 20mm thick granite (of any type) work table rubbed and pre polished) in cooking platforms, staircase incl riser & tread and similar work in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixtures of pigment to match with shade of granite complete and ensure best adhesion to surface complete

M&L for machine cut cudappah stone slab 20-25mm thick for vertical supports of kitchen platforms and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing of the exposed face complete all as directed and specified

Supply and fixed in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified.

S&F in repairs vitreous China, squatting pan, Orissa Pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) with PTMT trap of suitable size ( P or S type) including connection to trap and to flushing pipe, anti syphonic pipe etc complete including provision of cement concrete bedding & making good to floor complete all as specified and directed including taking out old one.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white with P or S trap with and including plastic water closet seat cover, jet spray , connection to trap, flushing pipe & anti -syphonage pipe etc including necessary materials for fittings & making good to floor complete all as specified and directed.

S&F in repairs 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets complete fixed in wall and floor to trap of WC as reqd complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of pre-painted cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore PTMT waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F in repairs 15 mm bib tap ( fancy type) , cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15 mm angle cock ( fancy type) , cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs Stop cock of size 15mm dia fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs brass chromium plated shower roses of size 125mm with or without swivel joints, any size, including shower arm 15mm size, 195mm long bend of 45degree with flange of CP fixing to steel pipe or union complete all as specified and directed.

S&F in repairs chromimum plated 15mm bore pillar taps with capstan head (but fancy type) screwed down high pressure with or without lettered Hot or cold with long screwed shank and fly nuts screwed for iron pipe and fixed all as specified.

S&F in repairs 15 mm dia PVC connections, 450 mm long with PTMT nuts of suitable size at two end complete all as specified and directed.

S&F in true horizonal level false ceiling using non asbestos (fibre cement) pre-painted decorative tiles of size 595x595x4mm thick manufactured by V- Board or equivalent including GI snap grid of size (600x600)mm, using hot dipped galvanised steel section, exposed surface with pre-coated capping, main tee of size 24 x 38mm having 0.27mm gauge at every 1200mm, centre to centre maximum and rotary stitched cross tee of size 24x 32mm, having 0.25mm gauge at 1200mm c/c & Wall angle of size 19x 19mm, having 0.35mm gauge fixed to the periphery of the wall. The above grid is suspended at every 1200 mm c/c in both directions using 2.0 mm thick pre-straightened GI wire with and including dismantling of boarding, any description fixed in any position with nails i.e. false ceiling and wall lining etc and similar position fixed with screws complete..

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-Charge.

M&L for Securing glass in metal frames glazed with putty including removing loose or decayed putty, painting/ oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work complete all as directed.

S&F sheet glass 3.00 mm thick ordinary quality and glazing with oil putty in square/ rectangle n.exc 0.5 Sqm in each pane with and including Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed.

S&F figured glass 4.00 mm thick, pin head type and glazing with oil putty in squares/rectangle exc 0.5 Sqm in each pane with and including Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed.

Parhar Enterprise (BID ID -3118115)

M/s.BAJRANG CONSTRUCTION (BID ID -3106361)

L.T Associate (BID ID -3113114)

SARATH ENTERPRISES (BID ID -3128797)

M/s Asrani and sons (BID ID -3119590)

REKHA ELECTRICALS (BID ID -3105383)