PROVN OF INDEPENDENT PIPELINE FROM CENTRAL PUMP HOUSE THROUGH N BLOCK TO NEW NAVY NAGAR AND ADDN ALTN AND IMPROVEMENT OF WATER SUPPLY AND DISTRIBUTION SYSTEM FOR AZ 2 AM AN BLDGS AT NEW NAVY NAGAR AND ADDN ALTN OF EXHAUST CEILING FAN IN CERTAIN BL

Amount

Excavation in trenches not exceeding 1.5 mtr wide not exceeding 1.5 mtr in depth and getting out soft/ loose soil all as specified.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cms in any type of soil all as specified. Note : For item No 1.00 and 2.00 above rate deemed to be included for earth work and form work required as per site requirement & as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) and removed of debris out side MD land all as specified.

M&L cement concrete 1:2:4, type B-2 (using 40 mm graded stone aggregate) as in support of CI pipes, foundation and hardstanding finishing even and fair without using extra cement all as specified.

Removing excavated material in soils exc 150 m but n.exc 500 m and depositing where directed all as specified.

S&F sluice valves flanged end, cast iron body, flanged and drilled and non rising type stainless steel spindle with nut, long body, class P N 1.6, confirming to IS 14846 of 2000 for following sizes including all flange joint with rubber or fiber board, bolts, nuts and washers complete including pumping out accumulated water all as specified and directed of following size :-

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Construction of brick masonery valve chamber of size 1.2 x 1.2 x 1.2 m (internal dimension) (above GL 0.30 mtr) suitable for fixing of sluice valves, 15cm thick foundation using PCC 1:4:8 type D-2 over 15cm thick hardcore of broken stone, 23cm thick brick walls built in cement and sand mortar 1:4, 15mm thick internal and external plaster including top of floor in cement and sand mortar 1:3, 15mm thick, finished even and smooth, without using extra cement, 5 mm thick plate cover on 50mm x 50mm x 6mm MS angle frame embeded in PCC 1:2:4 type B-1coping, having rectangular, hinged, opening of size 150 x 100mm with locking arrangements ,hold fasts, etc, applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces and earth work in any type of soil including disposal of debris outside MD land complete all as specified.

Supply, installation, Testing & Commissioning of Indoor type Programmable Logic controller based valve Automation , protection and communication Panel suitable for control and motorised of 2 Nos motorised valves . The panel should be suitable size faricated from 2.00 mm thick CRCA sheet and powder coated with angle iron supports not less than 40x40x5mm thick. The panel should comprise the following items :- (a) Auto change over in case of pump failure. (b) Single phase preventor. (c) Mannual mode operation.

Supply , installation, Testing & commissioning of Motor Actuator Butterfly valve consisting of quarter turn single phase Actuator and wafer type butterfly valve of size 300mm dia with appropriate bracket/mounting arrangement including two Nos limit switches for open and closed condition and splash proof enclosure, specifications & features :- (a) Input voltage : 230V, AC. (b) Designed line pressure: 10 Kg/.Sqcm. (c) Operating angle : 90 degrees. (d) Disc material : CI with nylon coating. (e) Limit Switches : 02 Nos for open and closed status. (f) In built serial/USB communication port. (g) In built data logger with memory. (h) In built SD Card. (j) Space heater. (k) In built blue tooth transreceiver with capability of paring with an android based smart phone to download logged data. (l) Mounting : Direction on valve. Make : EMTORK/HASEL HOFENER/HONEWELL/SIEMENS

Supply and fixing PVC insulated armoured copper cable 6 core 0.5 sqmm all as specified and directed

M&L Spigot and socket 150mm dia ductile Iron water tubing having cement mortar lining on inner surface and one coat of bituminous paint over exposed surface ISI marked, IS No.8329:2000, Class K-9 laid on wall/roof/floor/trenches with proper alignment as per site requirement and carryout testing against leakage before filling the trenches etc complete all as specified and directed at site. Note : Excavation and earth work shall be measured and paid separately.

M&L Spigot and socket 300mm dia ductile Iron water tubing having cement mortar lining on inner surface and one coat of bituminous paint over exposed surface ISI marked, IS No.8329:2000, Class K-9 laid on wall/roof/floor/trenches with proper allignment as per site requirement and carryout testing against leakage before filling the trenches etc complete all as specified and directed at site. Note : Excavation and earth work shall be measured and paid separately.

Supply , fixing , jointing , ductile iron fittings (DI Special) of size 150/300mm dia confirming to IS 9523 such as Bends, Cap flanges, Collars, Tees, Tail pieces, Elbows, Tappers and Reducers etc as per site requirement . Note . The DI specials shall be of minimum Class K-12 and from same manufacturers of DI Pipe.

Supply, fixing , ISI marked PUSH -ON JOINTS(Rubber Ring) of EPDM material confirming to IS 672:1999 and 1646 :1992, Suitable for DI Pipe of 150mm nominal diameter including testing against leakage all as specified and directed at sit.

Supply, fixing , ISI marked PUSH -ON JOINTS(Rubber Ring) of EPDM material confirming to IS 672:1999 and 1646 :1992, Suitable for DI Pipe of 300mm nominal diameter including testing against leakage all as specified and directed at site.

Supply and lay in trenches, galvanized iron pipe of Medium grade, including fittings 80mm dia. Note : Excavation and earth work shall be measured and paid separately.

Supply & Fixing PVC Triple layer and UV protected water storage tank of capacity 5000Ltrs, Hoisting and fixing in position at specfied location connecting with inlet/outlet pipe up to 40mm bore GI pipe connection completely all as specified and directed

Supply & Fixing PVC Triple layer and UV protected water storage tank of capacity 5000Ltrs, Hoisting and fixing in position at any location as directed by Engineer-in-charge 40mm bore GI pipe connection completely all as specified and directed

Supply and fix in repairs Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed of following size

15mm bore

20mm bore

Taking up or down steel tubing and connections, complete of following sizes:

15 mm bore

25 mm bore

50 mm bore

Supply and fix 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked,blue colour IS-15801, PP-R pipes SDR -II (PN-16) and PP-R plain fittings including all fittings ,reducers and fixed complete to walls and ceilings or laid in floors in short piece/length complete all as specified and directed by Engineer-in-charge for the following size of

15 mm bore

20 mm bore

25 mm bore

Supply and lay pipe galvanized iron pipe of Medium grade including fittings 40mm internal dia (DN).

Supply and lay pipe galvanized iron pipe of Medium grade including fittings 50mm internal dia (DN).

Supply and fix in repair 15mm gate valve with iron wheel head class I, made out of brass insert with union, ISI marked complete all as directed.

Supply and Fix in repair gate valve of size 40mm, cast copper alloy screwed down,high pressure with crutch or butterfly handle screwed both ends for iron pipe or union as directed by Engineer in charge.

Supply and fix in repair Swivel shower of PTMT of any colour for fixing with 15mm pipe(Minimum weightt 40gms).

Supply & Fix in repair Shower arm 15mm size ,195mm long with bend of 45 degree with flange of PTMT any colour (Minimum weightt 40gms).

Supply & fixing in repair PVC (LLDPE) Rectangular loft tank of net capacity 275 ltrs with gross capacity of tank at least 5% in excess of minimum net capacity including 03 Nos adopter with washer for inlet/outlet over flow as per manufactureres instructions and over all dimensions as 995-1200mm length,620-820mm width,285-485mm height ,300mm internal dia of hand hole,minimum wall thickness 2.75mm ,weight of tank 11 kgs withoutlid complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair replacement of PVC profile suitable for 275 ltr loft tank including fixing of aluminium channel around the profile completing all as specfied and directed.

Supply and fix in repair/ replacement Float valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed (Flat type) for iron pipe and fixed 15 mm bore.

Supply and fix in repair/replacement Float valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed (Flat type) for iron pipe and fixed 40 mm bore.

supply and fix galvanized steel structure for three 5000L PVC tank at a suitable height using H shapped column and three level supporting beam with equal angles of necessary size and supporting platform for tanks made up of MS plate of 6mm thickness , supporting equal angles and H column should be supported on reinforced concrete structure with nuts and bolts and all joints are to welded properly complete all specfied and directed by Engineer-in -charge.

M&L for Reinforced cement concrete (nominal mix) of type B 1:2:4(12.5mm) grade stone aggregate) for suporting H shaped colomns including formwork.

Supply and fix in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed 15 mm bore.

Supply and laying in trenches ductile Iron pipe , push on socket and spigot type conforms to IS 8329 ,internal lining of ordinary portland cement and external Zn & Zn-Al coating as per national standards and finishing layer of black bitumen ,and providing leak proof joint with suitable good quality synthetic rubber gasket conforming to IS-5382 including specials, Class “K-9” ,DN 150 mm (6”) bore. Note : Excavation and earth work shall be measured and paid separately.

Supply and laying in trenches ductile Iron pipe , push on socket and spigot type conforms to IS 8329 ,internal lining of ordinary portland cement and external Zn & Zn-Al coating as per national standards and finishing layer of black bitumen ,and providing leak proof joint with suitable good quality synthetic rubber gasket conforming to IS-5382 including specials, Class “K-9” ,DN 100 mm (4”) bore. Note : Excavation and earth work shall be measured and paid separately.

Supply and Fix gate valve of size 50mm, cast copper alloy screwed down,high pressure with crutch or butterfly handle screwed both ends for iron pipe or union as directed by Engineer in charge.

Supply , installation, Testing & commissioning of Motor Actuator Butterfly valve consisting of quarter turn single phase Actuator and wafer type butterfly valve of size 100mm dia with appropriate bracket/mounting arrangement including two Nos limit switches for open and closed condition and splash proof enclosure, specifications & features :- (a) Input voltage : 230V, AC. (b) Designed line pressure: 10 Kg/.Sqcm. (c) Disc material : CI with nylon coating.

Supply and fix PVC insulated armoured copper cable 6 core 1.5 Sqmm all as specfied and directed

Material and Labour for Point wiring complete with proper colour coding using, 1100 volts grade, 1.5 Sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor conforming to IS-694, part-II, ISI marked and including PVC casing and caping, ISI mark with all accessories on wall/ceiling/floor/roof etc, including sutable size of PVC board modular with plate and frame cover for fixing of modular or non modular fittings including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 volts multistranded copper conductor green colour as continuous earth wire connected to common earth dolly all as specified and directed for one fan point controlled by one switch. NOTE : Circuit conductor from MCB DB to Switch boards should not be less than 2.5sqmm.

S & F modular switch, 1 module, single pole, one way 6 Amps, 240 Volts.

S&F ceiling rose surface bakelite 65x20 mm with 3 terminals, isolated body.

S & F modular metal flush box, screwless with silver border of 3 module for mounting of modular switches including blank plate for blank module.

S&F modular white cover plate with frame, 3 module.

S & F modular stepped type (5 step) electronic fan regulator, 2 module, 230 volts ISI marked and connecting up complete.

S&F ceiling fan 1200 mm sweep, 230 V, 50 Hz, 5 star rating and energy saving, hanging on ceiling and connect with copper conductor multi stranded 3 core wire of size 14/0.0076.

S&F new louvers fixed type made out of 1.6mm GI sheet with horizontal ventilation, bending into shape of size 45cmx45cm (outer) with 20x3mm flat iron base of size 45cmx45cm complete all as specified and directed by Engr-in-Charge

S&F exhaust fan, 4 blade, heavy duty, double ball bearing, 230V, 50Hz,300mm sweep having power input 70W speed 1440RPM, including connection as required at site with flexible copper cable all as specified and directed.

Unity Enterprises