Construction of Academic Building I,Cotton University ,Panbazar,Guwahati 781001

Amount

EARTH WORK IN EXCAVATION

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified.

(A) Up to a depth of 2.00m below the existing ground level.

(a) In ordinary soil

Shuttering and shoring the earth at different levels in foundations where necessary with required prop, struts, planks, timbers, nails etc. including dewatering if necessary, complete as directed and specified (measurement to be taken in the face area timbered)

(a) Upto a depth of 1.5 metre

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.

(c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified.

(a) Within Guwahati city only

Extra lead per km truck carriage for sand gravel beyond the initial lead of 8 km.

CEMENT CONCRETE WORKS:

PLAIN CEMENT CONCRETE WORKS

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).

(a) In prop 1cement: 3 sand :6 coarse aggregate by volume

(b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete.

c) 100mm thick

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

REINFORCED CEMENT CONCRETE WORKS

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately)

(I) Using Mixer Machine

(A) In substructure up to plinth level

Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level.

N) Without using admixture, plasticiser

a) M15 grade concrete or Prop. 1:2:4

c) M25 grade concrete

(B) In super structure from plinth level up to 1st floor level.

i) Walls (thickness not less than 100mm) including attached pillasters, buttresses, plinth and string course etc.

N) Without using admixture, plasticiser

b) M20 grade concrete or Prop. 1:1.5:3

ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing.

N) Without using admixture, plasticiser

b) M20 grade concrete or Prop. 1:1.5:3

iii) Vertical and horizontal fins (thickness not more than 100mm) individually or forming box louvre and projected band.

N) Without using admixture, plasticiser

b) M20 grade concrete or Prop. 1:1.5:3

Extra over item Nos. 2.2.1 (I) (B), above for each subsequent floor or part thereof above the 1st floor level.

SHUTTERING & FORM WORK

TIMBER SHUTTERING ( FORM WORK)

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:

Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc.

(b) Using 25mm thick plank

Sides of tie beams, grade beams etc. at or below ground level.

(b) Using 25mm thick plank

Columns, Pillars, Posts & Strut

(a) Square, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face

(ii) Using 25mm thick plank

(b) Circular or curved in plan (Using 38mm thick plank)

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties.

(a) For depth not exceeding 1.0M.

(ii) Using 25mm thick plank

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like.

(a) Floors etc. upto 200mm in thickness.

(ii) Using 25mm thick plank

Sloping or Battering sufaces such as sloped slabs etc. including folded plates.

(a) Where inclination to horizontal plane does not exceed 30o requiring shuttering only on the underside.

(ii) Using 25mm thick plank

Vertical surface such as walls (any thickness), parapet walls, partitions, walls of septic tank, inspection pit and the like including attached pilasters, butresses, plinth and string courses and the like.

(ii) Using 25mm thick plank

Vertical ties, fins, sun breaker, louvers, bands, dropwalls etc.

(ii) Using 25mm thick plank

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing. (Using 38mm thick plank)

Providing form work of ordinary timber planking and removal of the same in edges of slabs and breaks in floors and walls etc. of in-situ reinforced concrete works upto first floor level.

(a) Thickness not exceeding 200mm.

Extra for each subsequent floor or part thereof above the First Floor level as mentioned in item no. 3.1.1 & 3.1.3(b).

Extra for each subsequent floor or part thereof above the First Floor level as mentioned in item no. 3.1.3(a).

Providing scaffolding using L&T-Doka access scaffold system upto a height of 40m. supported by frames of timber H-beams, bracings including suitable couplers, pins, tower spindles and 2nd class timber plank platforms complete as specified and directed by the department. (measurement to be taken on elevation area of the building/ structure).

MASONRY WORKS:

BRICK WORKS ( CONVENTIONAL / FLY ASH )

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.

(a).Brick on flat soling.

(c).Stone soling of thickness 150mm.

Filling sunken floor with broken jhama brick bats and sand including compacting and supplying of materials complete as specified and directed for all levels.

Extra cost for lifting of brickbats and sand for filling of sunk floor for each subsequent floors above the ground floor as directed and specified.

Autoclaved Aerated Concrete Block

Superlight Weight Autoclaved Aerated concrete Block work using Grade-I AAC block of compressive strength 40 kg/cm2 having dry density 550 to 650 kg/cum conforming to IS -2185 Pt-3 or Pt-4 in cement morter of prop 1:4 including racking out joints and curing complete as specified & directed.

(I) In Sub-structure upto plinth level including dewatering if necessary

(b) In proportion 1:4.

(II) In superstructure above plinth level up to 1st floor level.

(b) In proportion 1:4.(1 cement:4 sand)

Extra for AAC block walling for each subsequent floor or part thereof above the Ist floor level.

AAC Block work over item no. 4.4.1 (I) (II)

Superlight Weight Autoclaved Aerated concrete Block work using Grade-I AAC block of size 625x240 mm of different thickness of compressive strength 40 kg / sqm having dry density 550 to 650 kg/ cum conforming to IS- 2185 Pt-3 or pt-4 in cement morter of prop 1:4 including racking out joints and curing complete as specified & directed . ( protruding rod is to be provided at every 3 course interval and will be measured and paid seperately )

(II) In superstructure above plinth level up to 1st floor level.

(c) 125mm thick wall

Extra for AAC block walling for each subsequent floor or part thereof above the Ist floor level.

125 mm thick wall over item no 4.4.2 (II) ( c)

TILES WORKS

CERAMIC TILES

B) ON WALLS

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls).

a) Normal range Somany/ Orient/Nitco/Asian Make

i) Of size 200mmx200mm and above

VITRIFIED TILES

A) ON FLOOR

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department)

a) Normal range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make

i) Of size 400mmx400mm and above

KOTA STONE SLAB / SAND STONE FLOORING

Kota-stone slab flooring of 18 mm thick over 20mm thick base of cement plaster 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

(1) 550mm x 550mm

Extra for Granite finish in marble slab / tiles at all levels.

GRANITE FLOORING

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department).

(i) Normal Quality

Extra for Granite finish in marble slab / tiles at all levels.

ANTISKID TILES

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed.

(A) CERAMIC

i)Normal range (Sizes 300 mm x 300mm and above)

(a)Orient made: Galaxy Brown, Galaxy creama, Galaxy Pink, Galaxy Green, Pulsar Beige, Pulsar Blue, Pulsar Dove, Pulsar Pink, Burj Brown, Burj Green, Burj Slate

CEMENT PLASTERING

10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed.

a) In cement mortar 1:3

b) In cement mortar 1:4

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed.

A) On rough side

a) In cement mortar 1:3

b) In cement mortar 1:4

Extra over item no 6.2.1 to 6.2.3 for providing and mixing water proofing materials in cement mortar in prop as recommended by the manufacturer including curing complete as directed.

i) 10 mm thick plaster

b) In cement mortar 1:4

ii) 15 mm thick plaster

b) In cement mortar 1:4

Extra over item no 6.2.1 to 6.2.3 for plastering on celling and soffits of stairs up to 1st floor level (instead of plastering on walls) including curing complete as directed

Extra over item no 6.2.1to 6.2.3 for interior plastering above 1st floor level for every addl floor or part thereof including curing complete as directed.

a) On Single coat plaster

Extra over item no 6.2.1 to 6.2.3 for exterior plastering over wall up to a height of 1st floor level above ground level including curing complete as directed.

a) On Single coat plaster

Extra over item no 6.2.1 to 6.2.3 for exterior plastering over wall for every addl floor or part thereof beyond 1st floor level including curing complete as directed.

a) On Single coat plaster

b) On two coat plaster

HERITAGE FINISHING

Supplying and laying of permanent wall finish for interior and exterior walls with surface coating of Heritage Surface Texture of Bakelite Hylam Limited for all types of buildings at all levels as specified and directed by the department.

(n) Roller Coat ( application by special roller)

ROOF TREATMENT

Grading roof for water proofing treatment with

(a) Cement concrete 1:2:4 (cement: 2 coarse sand: 4 graded stone agg. 20 mm nominal size)

BLOCK BOARD SHUTTERS

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws.

a) Decorative type face panel and block board core.

(ii) 35 mm thick .

M.S GRILL WORK

Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws.

I . Plain grill

(c) Fixed to Brickwork/P.C.C/R.C.C.

P.V.C. DOORS & DOOR FRAMES

Providing, fitting and fixing 40mm x 48mm wood reinforced PVC chowkhats fixed to the columns / stiffeners / walls with necessary holdfast / sleeves etc. as specified and directed at all levels.

Providing, fitting and fixing 24mm/ 29mm thick polymer reinforced moulded PVC door shutters fixed to the chowkath with necessary hinges, screws, bolts etc. as specified and directed at all levels (Door fixtures and fittings to be measured and paid seperately)

a) 24mm thick

SLIDING WINDOW UPVC

Supplying and installing uPVC- Sliding Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall thickness 2.4mm with corners fusion welded, fully reinforced with Galvanized steel 1.5/2mm including interlock profile, glazing bead, grooving bead, brush seal, aluminum sliding track, stainless steel rollers, sealing wedge block, Espag, int handle, pop up handle, keeper, drain cap, fisher screws, packing pieces with all necessary stainlessness screws etc. complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Application of silicon sealant from inside / outside of Dowcorning / GE or equivalent With 5mm clear glass

(a) 2 Track Sliding Window with Flyscreen using uPVC section of sizes 88mm x 50 mm x 2.4mm thick wall for frame with inbuilt flyscreen track, 37mm x 61mm x 2.4mm thick wall for glass sash, 25mm x 49mm x 2.4mm thick wall for flyscreen sash having 1.5mm thick reinforcement, Interlock: 43mm x 23mm (Glass Panel) (WINSTA KOMMERLING/ FINESTA/ ENCRAFT)

(i) 2-Panel with 5mm clear float glass

CASEMENT WINDOW UPVC

Supplying and installing uPVC- Casement Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC sections of wall thickness 2.4mm, multichambered with corners fusion welded, fully reinforced with Galvanized steel 1.5/2mm including glazing bead, folding gasket, glazing gasket, friction stay, Espag handle, Espag, keeper, drain cap, run up block, fisher screws, packing pieces with all stainless steel screws complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets,bridging wedges and glass packers and with suitable water draining system. Fittings ROTO / GQ or Equivalent. Application of Silicon sealant from Inside / Outside of Dowcorning / GE or equivalent.

a) Single leaf Side hung Window using uPVC section of size 58mm x 57mm x 2.4mm thick wall for frame, 58mm x 68mm x 2.4mm thick wall for glass sash. With 5mm clear float glass (WINSTA KOMMERLING/ FINESTA/ ENCRAFT)

CASEMENT DOOR UPVC

Supplying and installing uPVC- Casement Door made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC sections of wall thickness 2.4mm, multichambered with corners fusion welded, fully reinforced with Galvanized steel 1.5/2mm including glazing bead, folding gasket, glazing gasket, locking arrangement, Espag handle, Espag, keeper, drain cap, run up block, fisher screws, packing pieces with all stainless steel screws complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Fittings ROTO / GQ or Equivalent. Application of Silicon sealant from Inside / Outside of Dowcorning / GE or equivalent.

(b) Double leaf Side hung Door with a Dummy Mullion - French Door using uPVC section of size 58mm x 69mm x 2.4mm thick wall for frame, 58mm x 109mm x 2.4mm thick wall for glass sash, 58mm x 61mm x 2.4mm thick wall for dummy mulion, Aluminium threshold at bottom. (WINSTA KOMMERLING/ FINESTA/ ENCRAFT)

i) Using 5mm clear glass

DISTEMPERING

f) Distempering with dry distemper of approved brand and manufacture(two coats)and of required shade on new wall surface to give an even shade, over and including priming coat of white primer after throughly brushing the surface free from mortar dropings and other foreign matter and including preparing surface even and sand papered smooth.

i). Extra over item no (f), (g) and (h) above for distempering every subsequent coat of distempering with dry distemper of approved brand and manufacture.

j). Extra over item no. (f) above for distempering with dry distemper on ceiling and or sloping roof.

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

(i) Thickness = 1.5 mm thick

PAINTING ON WOOD AND WOOD WOOD BASED SURFACES

Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting.

(a). With ready mixed paint , Wood primer (pink)

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping.

(i).Surfaces over 100mm in width or girth.

a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

PAINTING ON STEEL AND OTHER METAL SURFACE

Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper.

a). With ready mixed "red-lead/ red oxide" primer.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.

(i).Surfaces over 100mm in width or girth.

a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

(ii).Surfaces up to 100mm in width or girth.

a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

SPECIAL WATHER PROOF COLOURING

Finishing old/new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Dulux (ICI) paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats)

EXTERIOR WALL CLADDING

Supplying and installation of Exterior Wall cladding with modified clay materials of non carbon foot print having minimum thickness of 2.5mm , non breakable and flexible fixing with necessary adhesives, framing if needed, nails and screws including scaffolding for fixing the same in position. Finished and complete as per the specification and directed by the Engineer - In charge.

STONE CLADDING 221

BRICK CLADDING 308317

ALUMINIUM FITTINGS

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished )

a) Sliding door bolts

i) 300mm x 16mm

b) Tower bolts

i) 300mm x 12mm

c) Door handles

iii) 150mm

t) Door stopper with rubber stopper

REINFORCEMENT

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level)

a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL

(i) TMT Corrosion resistant steel (CRS) reiforcement bar

c) ISI approved Mild steel reinforcement bar(M.S.Bar)

Extra over item 18.1.1(a,b,c) for each subsequent floor or part thereof above first floor level.

BEAMS AND JOISTS

Structural steel work in single sections including cutting, hoisting, fixing in position and applying a priming coat of red lead paint (up to 4.6m height) from plinth level including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed.

b) In flat up to 25mm thickness

c) In M.S. angles, channels, Tees etc.

COLLAPSIBLE / ROLLING SHUTTERS

Providing and fixing in position collapsible M.S. shutters with vertical channels 20mmx10mmx2mm braced with flat iron diagonals 20mmx5mm size with top and bottom rails of T-iron 40mmx40mmx6mm with 38mm dia steel pulleys complete with bolts and nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

ANGLES/ FLATS/ BOLTS AND NUTS

Supplying fitting and fixing M.S.angles, M.S. flat, M.S. bolts and nuts including painting with red lead paint one coat complete as directed.

a) M. S. Angles…….

b) M. S. Flats…….

c) M. S. bolts & nuts…….

DOOR FRAMES

Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin- charge : Profile B Fixing with adjustable lugs with split end tail to each jamb

STEEL RAILING

Providing and fixing Stainless Steel ( Grade 304 ) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing,polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i.e. fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in charge. ( For payment, only weight of Stainless Steel member is to be considered. No extra payment for fixing accessories such as nuts, bolts, fasteners etc will be considered)

PLINTH PROTECTION AND DRAIN

Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified.

i). 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth of 100mm.

MACHINE DRIVEN PILES

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.4.1)

C) UNIFORM PILE

(II) Concret garade M25

v) Pile dia 500 mm

Empty boring for specified diameter piles from ground level to cut-off level.

f) Pile Dia 500 mm

REINFORCEMENT

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc)

(A) TMT bar made of Primary producer (From Primary producer)

WATER PROOFING OF CHAJJAS, ROOF SLABS, TERRACES, SUNKEN SLABS, SEPTIC TANK,OH TANK, RAFT SLAB IN BASEMENT, WALLS ETC.

LOAD TEST ON PILES

ROUTINE TESTS

Routine test for test loading to 1.5 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Initial test for test loading to 2.5 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Integrity testing of pile using low strain/ sonic integrity test/sonic echo test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust and chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test & submission of results, all complete as per direction of engineer in charge.

SURFACE PREPARATION

Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

WATER PROOFING OF CHAJJAS, ROOF SLABS, TERRACES, SUNKEN SLABS, SEPTIC TANK,OH TANK, RAFT SLAB IN BASEMENT, WALLS ETC.

(A) Supplying, mixing, laying and applying the following waterproofing systems over Raft slabs, Roof slabs, Terraces etc. including curing complete as specified and directed by the Department at all levels.: (i) 1mm thick single coat of Master Crete M-81 of Choksey Chemicals /Dr. Sealkit Sealcrete (Asian Chemicals)/ mixed with cement in the ratio 1:2 as a prime coat. (ii) 3mm thick Polymer modified mortar - Cement sand mortar (in prop 1:3) mixed with Master Crete M-81/Dr. Sealkit Sealcrete (Asian Chemicals) @ 15% by weight of cement. (iii) 1mm thick coat of Master Crete M-81 /Dr. Sealkit Sealcrete (Asian Chemicals) mixed with cement in the ratio 1:2 as final coat.

TREATMENT OF CONSTRUCTION JOINTS

Providing treatment of constructional joints in R.C.C. walls and slabs by supplying, mixing and applying a 2-component epoxy resin based bonding agent for old to new concrete like Master Bond - EP/ Concresive 1414 of BASF/Dr. Sealkit Bond OTN (Asian Chemicals) (with an open time of 6 hours at 30 deg Celsius) as per detailed drawings or as specified and directed by the Department complete at all levels.

(i) Slab/ Wall thickness upto 200mm

Demolishing R.C.C./ P.C.C. pile head of different diameters carefully without disturbing the remaining portion of the pile including opening out of the pile head to be demolished by excavating the earth upto required depth and clearing the debris as directed.

Jungle clearence including uprooting of vegitation, grass, brush-wood, sapling and trees not exceeding 300mm girth and disposal of the same outside the periphery and lift upto 1500mm

Providing and fixing galvd. / M.S. tube (light grade) outlet (spout) in cement mortar 1:3 including cutting and making good the wall

(a).25mm bore - 300mm long.

Providing precast R.C.C slab over drain ,septic tank etc. in prop. 1:2:4 reinforced with 10mm M.S. bar @ 150mm centre both ways tying with 20 gauge black annealed wire with necessary shuttering , curing etc. complete including fixing in position as directed.

b) 75mm thick slab

PRE CONSTRUCTION ANTI - TERMITE TREATMENT

Pre construction anti - termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surface area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.

a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Pre construction anti - termite treatment in the back fill in immediate contact with the foundation structure after completion, column, wall etc. to a depth of 450mm and width 300mm (when required refill in 200mm thick layers) applying the emulsion @ 5 (five) litres per square meter towards the concrete and masonry walls so as to ensure earth in contact with the structure well treated - with chemical (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.

a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.

a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Pre construction anti - termite treatment by applying in the junction of walls, column with the floor before laying floor and after operation of item no. 26.1.3 above making a channel 30mmx30mm all over the walls and making rod holes @ 150mm apart up to ground level below and applying emulsion @ 11 litres per square meter of vertical plinth wall surface inside the building so as to soak the soil with the emulsion up to the ground level and refill the holes and channel with the original materials obtained in making channels (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete

a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Pre construction anti - termite treatment by applying the soil along the external perimeter of the building (after construction completed) to a distance close to the plinth wall as specified and as directed by the deptt. up to a depth of 300mm making rod holes along the line @ 150mm apart to a depth of 300mm and applying emulsion @ 4.5 litres per running meter ensure moistening of the soil with emulsion (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.

a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

PVC PIPES,BENDS,JUNCTIONS,TEES ETC.

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified.

a) In exposed surfaces or in trenches.

(iv) 75mm dia.

CUBICAL TOILET (GENTS)

Supply, Installation and commissiong of toilet cubical of standard size as per architectural drawing and specification as follows:

MODLE TYPE -ZMS LYLON SERIES

Thickness of Compact Laminate :12 mm

Color of HPL Boards : Single Color

Size of Cubicle : 1000mm (W) x 1550mm (D) x 2003mm (H)

Door Size :1750mm (H) x 610mm (W)

Overall Height of Cubical :2003 mm (Inclding botton Gap of 150mm)

Accessories : Standard - Merino Make / green or equevent make Aluminum, Nylon Polyamide 6 accessories)

a) Aluminum "U" Channel

b) Aluminum "F" Channel

c) Aluminum Door Stopper Channel

d) Aluminum Top Rail

e) Nylon Coat hook

f) Nylon Privacy Thumb turn c/w Occupancy Indicator

g) Nylon Door Knob

h) Nylon hinges-Gravity to close

i) Nylon Adjustable Foot

j) Rubber Door Stopper Lining

k) S.S.Screws 304 G & P.V.C Wall Plugs

Inculsive of all necessary fittings and fixures to complete and finish as per instruction of Engineer in charge.(The estimate is prepared for a complete floor with 14 units of W.C & Bath)

Supply, Installation and commissiong of toilet(Urinal) cubical of standard size as per architectural drawing and specification as follows:

MODLE TYPE -UMP NYLON SERIES

Thickness of Compact Laminate :12 mm

Color of HPL Boards : Single Color

Size of UMP :500 mm (W) x 1200 mm (H)

Overall Height of Cubical :1850 mm (Inclding botton Gap of 650mm)

Accessories : Standard - Merino Make / green or equevent make Aluminum, Nylon Polyamide 6 accessories) - BLACK

a) Right Angle Brackets

b) S.S.Screws 304 G & P.V.C Wall Plugs

Inculsive of all necessary fittings and fixures to complete and finish as per instruction of Engineer in charge

CUBICAL TOILET (LADIES)

Supply, Installation and commissiong of toilet cubical of standard size as per architectural drawing and specification as follows:

MODLE TYPE -ZMS LYLON SERIES

Thickness of Compact Laminate :12 mm

Color of HPL Boards : Single Color

Size of Cubicle : 1000mm (W) x 1550mm (D) x 2003mm (H)

Door Size :1750mm (H) x 610mm (W)

Overall Height of Cubical :2003 mm (Inclding botton Gap of 150mm)

Accessories : Standard - Merino Make / green or equevent make Aluminum, Nylon Polyamide 6 accessories)

a) Aluminum "U" Channel

b) Aluminum "F" Channel

c) Aluminum Door Stopper Channel

d) Aluminum Top Rail

e) Nylon Coat hook

f) Nylon Privacy Thumb turn c/w Occupancy Indicator

g) Nylon Door Knob

h) Nylon hinges-Gravity to close

i) Nylon Adjustable Foot

j) Rubber Door Stopper Lining

k) S.S.Screws 304 G & P.V.C Wall Plugs

Inculsive of all necessary fittings and fixures to complete and finish as per instruction of Engineer in charge.(The estimate is prepared for a complete floor with 14 units of W.C & Bath)

EUROPEAN TYPE WATER CLOSET

Providing fitting and fixing Vitreous china Dual Flush / Floor Mounted Coupled / Extended water closet (European type W.C pan 400mm high) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately)

A) Parryware make

(xv) Indus (inclusive of seat cover and fittings) (white) (Cat. No. C0215/14/66) (S/P Trap)

AUTOMATIC FLUSHING CISTERN

Supplying, fiting and fixing automatic flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately)

ii) Hindware make

a) White

Auto Cister 10 litre (Cat. No.C61002)

URINAL

Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required.

(A) Parryware Make

(a) White

(i) New Magnum (Cat. No.C0575)

WASH BASIN

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately)

PEDESTAL BASIN (with pedestal)

(A) Parryware Make

(a)White

(iv) Cascade NXT 550 x 440 with long Pedestal (Cat. No.C0404/C0380)

Counter Top Basin

(A) Parryware Make

(iii) Cascade NXT 550 x 445 (Cat. No.C0430) (coloured)

MIRROR

Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified.

Providing fitting and fixing Decorative Mirror complete as directed and specified.

(A) Parryware Make

(a) Size 800mm x 600mm

(b) Size 600mm x 450mm

SHELF

Providing fitting and fixing Glass Shelf complete as directed and specified.

Glass shelf with C.P. guard rail

(ii) Sona make (Cat. No.TR-0701)

SOAP TRAY,SOAP DISH,LIQUID SOAP DISPENSER AND LIQUID SOAP CONTAINER

Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified.

(a) Parryware Make

(ii) Wall Soap tray (Cat. No.C9951)

Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified.

(iv) SONA make (Cat. No.AL-1011)

TOWEL RAIL,TOWEL RACK & TOWEL RING

Providing, fitting and fixing CP towel rail complete as directed and specified.

(b) Sona make

(i) Towel rail Diplomat 300mm long (Cat.No.TR-0605)

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified.

(b) Sona make

(i) Towel ring round (Cat.No.TR-06051)

(ii) Towel ring round Aristo (Cat.No.TR-0652

TOILET PAPER HOLDER

Providing, fitting and fixing Chrome Plated TOILET PAPER holder complete as directed and specified.

(a) Jaquar make

(i) Continental toilet paper holder (Cat.No. ACN-1151N)

WASTE COUPLING

Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified

(b) Sona

(i) Rupa 32mm (HT/ FT) (Cat.No.WS-0801)

BOTTLE TRAP

Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified.

(b) Sona make

(i) Bottle trap indian 32mm (Cat. No.BT-0751)

Providing, fitting and fixing Chrome Plated bottle trap pipe complete as directed and specified.

(a) Sona make

(i) Pipe for bottle trap 300mm long (Cat. No.BT-0761)

PVC PIPES,BENDS,JUNCTIONS,TEES ETC.

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified.

a) In exposed surfaces or in trenches.

(ii) 110mm dia.

(iv) 75mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

(iv) 75mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified.

a) In exposed surfaces or in trenches.

(ii) 110mm dia.

(iv) 75mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

(iv) 75mm dia.

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.

a) In exposed surfaces or in trenches.

(ii) 110mm dia.

(iv) 75mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

(iv) 75mm dia.

Supplying fiting and fixing 45degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.

a) In exposed surfaces or in trenches.

(ii) 110mm dia.

(iv) 75mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.

a) In exposed surfaces or in trenches.

(ii) 110mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

(iv) 75mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.

a) In exposed surfaces or in trenches.

(ii) 110mm dia.

(iv) 75mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

(iv) 75mm dia.

Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.

a) In exposed surfaces or in trenches.

(ii) 110mm dia.

(iv) 75mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

(iv) 75mm dia.

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.

a) In exposed surfaces or in trenches.

(ii) 110mm dia.

(iv) 75mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

(iv) 75mm dia.

Supplying fiting and fixing PVC double ‘Y’ plain of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.

a) In exposed surfaces or in trenches.

(iv) 75mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

(iv) 75mm dia.

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.

a) In exposed surfaces or in trenches.

(ii) 110mm dia.

(iv) 75mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

(iv) 75mm dia.

Supplying fiting and fixing PVC coupler of (Supreme / Prince)or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.

a) In exposed surfaces or in trenches.

(ii) 110mm dia.

(iv) 75mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.

(ii) 110mm dia.

(iv) 75mm dia.

Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.

a) In exposed surfaces or in trenches.

(iii) 110 mm x 90 mm

(iv) 110 mm x 75mm

(viii) 75 mm x 63mm

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified.

(ii) 110mm dia.

(iv) 75mm dia.

COWEL

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified.

(iii) 90mm dia. PVC cowel of ISI make

GRATING

Providing fiting & fixing C.I. Grating to the floors complete as directed and specified.

(a) 110mm dia

SOAK PIT AND INSPECTION CHAMBER

Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats/Charcoal covered with earth over a layer of A.C. plain sheet above brick bat filling complete as directed. (sizes of soak pit may vary depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table.

Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

INTERNAL WATER SUPPLY WORKS

PIPING

Providing and fixing 3 layer (Outer green / GREY coloured UV Stabilised, middle black coloured UV Stabilised and inermost layer white coloured with antimicrobial property) Fusion welded PP-R ( Poly propylene-random copolymer) Pipes, SDR 7.4 having thermal stability for hot and cold water supply conforming IS 15801-2008 including all plain PP-R fittings and brass threaded PP-R fitting and clamping, cutting and making good to the damages.

(A) Exposed or in trenches

SFMC/ FUSION brand or other brand of equivalent quality.

a) PN-16 Pipe,16mm OD,SDR-7.4

b) PN-16 Pipe,20 mm OD,SDR-7.4

c) PN-16 Pipe,25 mm OD,SDR-7.4

d) PN-16 Pipe,32 mm OD,SDR-7.4

e) PN-16 Pipe,40 mm OD,SDR-7.4

f) PN-16 Pipe,50 mm OD,SDR-7.4

(B) Concealed pipe with cutting chases & making good the walls

SFMC/ FUSION brand or other brand of equivalent quality.

a) PN-16 Pipe,16mm OD,SDR-7.4

b) PN-16 Pipe,20 mm OD,SDR-7.4

c) PN-16 Pipe,25 mm OD,SDR-7.4

d) PN-16 Pipe,32 mm OD,SDR-7.4

e) PN-16 Pipe,40 mm OD,SDR-7.4

f) PN-16 Pipe,50 mm OD,SDR-7.4

BIB COCK

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately)

Jaquare make

(i)Standard

STOP COCK

Supplying fitting and fixing stop-cock of approved brand of size as mentioned below and directed and specified (G.I. & C.P. pipes will be measured and paid separately

I) Brass stop cock (heavy) of Sant make

(i)15mm dia

(ii)20mm dia

(iii) 25mm dia

(iv)32mm dia

(v) 40mm dia

(v) 50mm dia

PUSH BIB COCK

Supplying fitting and fixing push bib cock 15mm dia complete as directed and specified as follows. (pipes will be measured and paid separately).

a) C.P.C.H.

(a) Light type

PILLAR COCK

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed.

Jaguar make

(a) Continental

VALVE

Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed.

a) 50mm dia

b) 40 mm dia.

c) 25 mm dia.

d) 2O mm dia.

e) 15 mm dia.

Supplying and fitting ball valve as specified and directed..

a) 25 mm dia. (gun metal)

b) 20mm dia. (gun metal/Copper)

Supplying fitting and fixing gun metal check valve including necessary threads to pipes.

a) 50 mm dia (Heavy type)

b) 40 mm dia (Heavy type)

Supplying fitting and fixing G.I. Foot valve with strainer including cutting necessary threads to pipes.

a) 50 mm dia (Heavy type)

b) 40 mm dia (Heavy type)

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes

2000 Lt capacity

(a) Sintex make

1500 litre capacity

(a) Sintex make

1000 litre capacity

(a) Sintex make

FIRE ALARM SYSTEM & FIRE FIGHTING SYSTEM

FACP - 6 Loops And Networkable

Supply of Microprocessor based Intelligent Addressable 6 Loop MAIN FIRE ALARM PANEL having Microprocessor CPU and display of LED Screen with Touch Sensitive Keyboard. PANEL should be ONE single panel having 6 Loops with Networking Provision. Each Loop should be able to take minimum 232 Detectors & Devices . The panel shall be soft addressable type and Networkable . The panel shall be able to give pin point location of all fire/fault conditions. Further, the panel must be able to automatically switch off respective control switches when ever any alarm is triggered. The panel shall 1 have in built rectifier, Loop cards,provision for externel & internal printer(if required), L C D unit to indicate Fire/Fault Signal with address and analog output, built in printer to log all fire or fault events complete in all respects, integral SMF lead acid batteries with sealed cells of 24 V capable providing 48 Hrs Battery Back up during Main Power supply failure condition. (Manufacturer should be strictly following VdS/FM Approvals) (Make:ESSER/NOTIFIER/GENT)

Detectors

SITC of addressable Intelligent Microprocessor based Ceiling Mounted Twin Angle Optical Smoke cum Thermal Multicriteria Detector dent memory & resident decision algorithm. Optical Detection by both Forward & Backward Light Scattering principle having in-built isolator with operating temperature range 0 - 65 deg C . It should have Standard Detector Base with NO 330 DIP/ROTARY or Mechanical address switch but soft Programmable OR Multicriteria Detector to be implemented in CLASS A Style 7 Wiring of NFPA having Isolator before and after each Detector. Manufacturer should be strictly following VdS/FM Approvals) (Make : ESSER/NOTIFIER/GENT)

Supply of addressable Intelligent Microprocessor based Ceiling Mounted Multicriteria Detector with CO sensore having resident memory & resident decision algorithm. . Detector with in-built isolator with operating temperature range -10 - 50 deg C . It should have Standard Detector Base with NO 36 DIP/ROTARY or Mechanical address switch but soft Programmable OR Detector to be implemented in CLASS A Style 7 Wiring of NFPA having Isolator before and after each Detector or inbuilt fault isolator. (Manufacturer should be strictly following VdS/FM Approvals) Make :ESSER/NOTIFIER/GENT)

SITC of addressable Intelligent Microprocessor based Ceiling Mounted Twin Angle Optical Smoke cum Thermal Multicriteria Detector dent memory & resident decision algorithm. Optical Detection by both Forward & Backward Light Scattering principle having in-built isolator with operating temperature range 0 - 65 deg C . It should have Standard Detector Base with NO 330 DIP/ROTARY or Mechanical address switch but soft Programmable OR Multicriteria Detector to be implemented in CLASS A Style 7 Wiring of NFPA having Isolator before and after each Detector. Manufacturer should be strictly following VdS/FM Approvals) (Make : ESSER/NOTIFIER/GENT)

Address Manual Call Point

Supply of Microprocessor based Intelligent Soft Addressable Single Action Pull down type Manual Pull Station having Inbuilt Isolator MCP should be soft Addressable . In case the MCP is not having inbuilt Isolator then Implementation of Isolator Module before and after every MCP as per Class A Style 7 type Wiring of NFPA standard. (Manufacturer should be strictly following VdS/FM Approvals) (Make: ESSER/NOTIFIER/GENT)

Hooter

Supply of addressable Intelligent Microprocessor based Ceiling Twin Optical Smoke cum Thermal Multicriteria Detector having 2 emitter and Single Receiver to liminate any false fire Signature along with Sounder Flasher and Speech to be used in the Corridor Areas with memory & resident decision algorithm. Optical Detection by both Forward & Backward Light Scattering principle having in- built isolator with operating temperature range 0 - 65 deg C . It should have Standard Detector Base with NO DIP/ROTARY or Mechanical address switch but soft Programmable OR Multicriteria Detector to be implemented in CLASS A Style 7 Wiring of NFPA having Isolator before and after each Detector. It will get fix with Junction Box. (Manufacturer should be strictly following VdS/FM Approvals) (Make : ESSER/NOTIFIER/GENT)

Transponder -INPUT/OUTPUT MODULE

Supply of Intelligent Addressable Intelligent Transponde 1 input and 1 Output for activation of Damper/Ahu etc and also taking Input from Sprinkler/Pressure Switch etc. In case the Manufacturer supplies individual Control and Monitor Modules , then it should be clubbed with 4 nos Monitor Modules and 2 nos Control Modules in a single Housing. (Manufacturer should be strictly following VdS/FM Approvals) (Make: ESSER/NOTIFIER/GENT)

Responseindicator

Supply of Responseindicator

Cable Conduit

Supply of 2x1.5 sq.mm CU conductor PVC Insulated screened and unarmoured & FRLS cable with 25 mm PVC conduit & acessories. (Manufacturer should be strictly following ISI Standards)

Providing & fixing MS Black steel pipe Heavy class conforming to IS: 1239/3589 including all fittings viz. elbows, tees, flanges, e.t.c. reduces, clamps, MS support dash fasteners etc. including painting the pipe with one coat of approved red oxide primer and two coats of approved red enamel paint and welded joints complete with cutting and making good the walls, floors or any other surface

200mmdia(6.35mmthick)

150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

42 mm dia

32 mm dia

25 mm dia

Providing & fixing swinging type CI Non return Valve with flap and SS hinges complete including matching flanges, nuts & bolts conforming to IS 5312

200 mm dia

150 mm dia

Providing & fixing CI butterfly valve ( wafer type) with counter flange & nut bolts

200 mm dia

150 mm dia

Providing & fixing Suction Strainer with foot valve

200 mm dia

80 mm dia

Providing & fixing GM oblique type hydrant valve with 63 mm outlet GM instantaneous female coupling with rubber cap and chain conforming to IS ; 5290 including matching flange, gasket, nuts and bolts complete.

Single headed

Providing and Fixing 63 mm dia rubberized reinforced rubber line hose pipe in 15 m length conforming to IS : 636 Type A ISI marked with Gunmetal male and female instantaneous coupling conforming to IS 903 wounded with 18 SWG copper wire complete

Providing and Fixing gunmetal branch pipe with 20 mm nozzle conforming to Is 903 complete.

Providing & fixing swinging type hose reel drum fabricated from 14 SWG CRCA sheets painted with red color stove paint 2 coats over 1 coat of primer with 30 m long 20 mm dia rubber hose pipe with 10kg / sqcm working pressure with GM self closing shut – off nozzle of 5 mm outlet fixed on wall with dash fasteners.

Providing and Fixing FRP hose box with lockable arrangements to accommodate 2 RRL hose of 15 m length and one branch pipe painted white inside and red outside with one key.

Providing and Fixing 150 mm dia dial type pressure gauge complete with pipe stem and cock

Providing and fixing Fire pump with CI body, bronze impeller, C 40 shaft coupled by means of flexible coupling with electric motor/engine Antivibration pads,, coupling guard , baseplate etc.

Electric Motor Driven Fire pump.

Capacity of pump =2400 LPM Head = 35 Meters

Electric Motor Driven Jockey Pump

Capacity of pump =180 LPM Head = 70 Meters

Providing & fixing dust and vermin proof cubicle type motor control centre fabricated from 14 SWG MS sheet with powder coated finish and comprising of required incomer/ outgoing MCCB, metres & other accessories, for above pump set under serial No. 11

Providing and Fixing heavy duty PVC insulated, PVC armoured aluminium conductor cables 1100 V grade including necessary support clamps and connection lugs complete in all respect.

Power cable 3 core X 35 mm2

Power cable 3c X 10 mm2

Control cable copper armoured, 2cX2.5mm2

Providing and fixing GI earthing strip 25mm x 6 mm thk. From allmotors and MCC panel to be connected in all approved manner to general earthing system.

Providing and Fixing Gunmetal collecting head with 63 mm dia instantaneous type inlet 150 dia flanged, outlet with built in check valve for fire brigade connection to fire riser ( IS 904 )

Three Way

Providing and fixing INDFOSS make pressure switches for cut– out and cut in pressure with cock

Providing & fixing Installation Control Valve alongwith treams, actuator, water motor gaung,instruments & other accessories as required

150 mm dia

Providing & fixing quartzoid bulb sprinkler 68 C along with necessary attachment.

Pandent Type

Providing and fixing carbondioxide fire extinguisher consisting of welded MS cylindrical body, squeeze, lever discharge valve, fitted with internal discharge tube, high pressure discharge hose, discharge nozzle, suspension bracket, finished externally with red enamel paint and fixed to wall with brackets with rawl plug / dash fasteners complete with internal charge .

Capacity 4.5 kg. ISI marked

Providing and fixing mechanical foam type ( ISI marked ) fire extinguisher consisting of welded MS cylindrical body, squeeze, lever discharge valve, high pressure discharge hose, discharge nozzle, suspension bracket ISI marked finished externally with red enamel paint and fixed to wall with brackets with internal charger .

9 liters Capacity

Providing & fixing water Co2 ( ISI marked ) extinguisher including all accessories with wall bracket with rawl plug.

Capacity 9 liters.

Providing & fixing dry powder extinguisher consisting of welded MS cylindrical body, with discharge valve, nozzle and CO2 cartige and hanging arrangement complete

Capacity 5 kg. ISI marked

Supply, application, testing of PYPKOTE Anti-corrosive (4mm thick) and primer

Providing and fixing of Air Release Valve 25 mm dia along with 25 mm dia GM globe valve

Orifice Plate (S.S)

2 way fire brigade suction outlet

Fire bucket with stand

Internal Electrical Works

Wiring in surface/ recessed PVC conduit FR (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) cable

CIRCUIT WIRING

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system

With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system.

With 4 x 10 sq. mm. + earth continuity with 2x6 sq. mm. cable in 40 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 4 x 16 sq. mm. + earth continuity with 2x10 sq. mm. cable in 40 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for 5 pin 6 amp plug with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) including 5 pin 6 amp socket outlet (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.)make) and 6 amp flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.)make) earthing the 3rd pin of the socket as required on the switch board in surface/ recessed P.V.C. conduit wiring system. When fitted on same board of light and fan.

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete.

Medium point up to 6.00 metre. Length

Long point up to 10.00 metre. Length.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.)

Long point up to 10.00 metre. Length.

Wiring for light/fan/call bell point with 3x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) ceiling rose etc. complete

Short point up to 3.00 metre. length.

Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

MODULAR SWITCH

Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE in surface/ recessed system complete as per direction of department.

1-2 module type Metal

3 module type Metal

4-5 module type Metal

6-8 module type Metal

10 module type Metal

12-16 module type Metal

Supplying including fitting fixing of following front plate of suitable colour MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE as per direction of department.

1 Module

2 Module

3 Module

4 Module

6 Module

8 Module

10 Module

16 Module

Supplying including fitting and fixing of TV co-axial outlet MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying with fitting and fixing of RJ-11 Telephone jack MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying with fitting and fixing of CAT 6 RJ-45 Computer jack in one module MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying with fitting fixing of blank plate single in modular switch system MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE complete as per direction of department.

Supplying with fitting and fixing of 100 watt electronic modular fan speed controller 4 - Step 2 - module type MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying with fitting fixing of 6 amp one way modular clip in bell push with LED MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying including installation of socket outlet 6/16 Amps 3/5 pin combine shuttered complete , MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying including installation of socket outlet 6 Amps 3 pin combine shuttered complete , MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying with fitting fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying with fitting fixing of 6 amp one way modular clip in switch, MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

SUPPLY AND FIXING OF RIGID PVC CONDUIT (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) IN SURFACE AND RECESS WIRING SYSTEM

Supply and fixing 19 mm dia 2.00mm average wall thickness heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in recessed system including cutting the wall and making good the same as required:

Wiring with P.V.C. insulated unsheathed 1.1 K.V. grade single core copper conductor FR cable in existing surface/ recessed conduit wiring system

Wiring for Co - axial Jelly Flooded (Unarmoured) (FINOLEX /RR KABEL /NICCO / ANCHOR make) cable in existing surface conduit wiring system including connection etc as required.

Co - axial Jelly Flooded (Unarmoured) RG 6 (Copper)

EPABX

Supplying ,installation, testing & commissioning of Distribution Box 20 pairs with Krones ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of 2 pair Unarmoured Telephone Cable through existing conduit in surface/ recess system.

FITTINGS AND ACCESSORIES (ALL PRODUCTS SHOULD BE ENERGY EFFICIENT AND ENVIRONMENT FRIENDLY)

Supplying and fixing of Call bell ( Buzzer ) including 5/ 6 amp capacity button piano type bell push switch including connection as approved by the Deptt.)as required.

Supplying and fixing of Fan box (AKG or equivalent as approved by the Deptt.)with inbuild rod as required.

SWITCH GEAR & PROTECTION

INDUSTRIAL SOCKETS, DB WITHOUT MCB & MCCB , MCB, RCCB, RCBO, SFU, CHANGE OVER ETC. (C&S, Havells, INDOASIAN, HPL OR EQUIVALENT as approved by the Deptt.)MAKE)

Supplying fitting and fixing industrial Plug & Socket in surface mounting SPN sheet steel powder painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of DP MCB complete with making necessary connection etc. as specified and directed by the Deptt.

20A Capacity. (C&S, Havells, INDOASIAN, HPL or equivalent as approved by the Deptt.)make)

Supplying with fitting and fixing sheet steel, phosphatised, powder painted Single door surface mounting MCB enclosure incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt.

Schneider neo break, C&S, Havells, INDOASIAN, HPL or equivalent as approved by the Deptt.)make)

4 way single door

MCB DB (ABB, SCHNEIDER MG, LEGRAND, HAGER MAKE) & (SCHNEIDER NEO BREAK, C&S, Havells, INDOASIAN, HPL OR EQUIVALENT MAKE AS PPROVED BY THE DEPTT.)

MCB IN-comer SPN DB

ABB, Schneider MG, legrand, Hager make)

8 way SPN Double Door

12 way SPN Double Door

MCB IN-comer TPN (Horizontal DB)

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 double door surface mounting TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt.

ABB, Schneider MG, legrand, Hager make)

4 way TPN (4+12) Double Door

MCB IN-comer TPN ( VERTICAL DB)

Supplying with fitting and fixing MCCB income and MCB outgoing sheet steel, phosphatised, powder painted double door IP-43 surface mounting vertical TPN MCB DB incorporated with bas-bar up to 250A, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt.

ABB, Schneider MG, legrand, Hager make)

4 way TPN (4+12) double door

8way TPN (4+18) double door

MCB, MCCB, RCCB, RCBO (ABB, SCHNEIDER MG, LEGRAND, AND HAGER MAKE) & (SCHNEIDER NEO BREAK, C&S, Havells, INDO ASIAN, HPL OR EQUIVALENT MAKE AS PPROVED BY THE DEPTT.) MCB (Conform to IS / IEC 60898-1:200/ MCCB (Conform to IS/IEC 60947- RCCB (Conform to IS/IEC 12640 / 61008)

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.

C Series (Schneider MG, legrand, Hager make)

Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.

C Series (ABB, Schneider MG, legrand, Hager make)

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.

100/300mA sensitivity DP RCCB (ABB, Schneider MG, legrand, Hager make)

Supplying with fitting and fixing TP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.

C Series (ABB, Schneider MG, legrand, Hager make)

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.

C Series (ABB, Schneider MG, legrand, Hager make)

Supplying with fitting and fixing panel mounting open execution 25 KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure of the following capacity complete with making necessary connection as approved by the Deptt. as specified and directed by the deptt.

25 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Siemens make)

Supplying with fitting and fixing panel mounting open execution 35/36KA 415V 50Hz 3P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.

35/36 KA 415V 50 Hz 3P MCCB (ABB(S6) , Schneider, legrand, Siemens, L&T D-shine make)

Supplying with fitting and fixing panel mounting open execution 50 KA 415V 50Hz 3P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved by the Deptt.),as specified and directed by the deptt.

50 KA 415V 50 Hz 3P MCCB (ABB(S6) , Schneider, legrand, Siemens, Indo Asian make)

EARTHING

Supply, installation & testing of G.I. earth station with perforated 40 mm dia and 4.50 Metre long heady duty G.I. pipe with necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement 300 mmx300 mmx6 mm hinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt (5 K and Charcoal (64 K in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the Deptt.

Supply, installation & testing of Copper Plate earth station with 600 mmx600 mmx3 mm copper earth plate with necessary 40 mm dia. G.I. medium duty watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm C.I. hinged cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt (5 K and Charcoal (96 K in G.I./Copper plate Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the deptt .

Supplying & laying of 6 SWG G.I. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 25X5mm size G.I. strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 25X5mm size Copper strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of Brass nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supply, fitting & fixing of Lighting Finial Arrestor made of 25 mm dia 300 mm long solid G.I. tube having 85 mm dia. single prong at top and 3 mm base plate at bottom complete with fitting & fixing with G.I. nuts & bolts on roof, RCC slab, top of column etc. as specified and directed by the deptt.

Supply, fitting & fixing 20 mmx5 mm G.I. strips drawn on vertically or horizontally on building wall/parapet wall in surface system complete with supply of G.I. Nuts & Bolts, Screws etc including riveting, soldering and making connection as approved by the Deptt.)with earth electrode G.I. strips and Lightning Arrestor etc. as specified and directed by the deptt.

CEILING FAN, EXHAUST FAN AND AIR CURTAIN

Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator].

Premium model 1200 mm Sweep (ORIENT PSPO make) / Premium model 1050 / 1200 mm Sweep SS-390 Deco Havells make) [ F ]

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department.

Domestic

Ventil Air DB 300 mm sweep (Havells make) [EF]

Heavy Duty 450 mm sweep 900 RPM Single phase (ORIENT make) [EFH ]

INVERTER/ UPS AND RACK FOR LAN WORKS/ LAN WORKS/ AVR

Supply, installation testing and commissioning of following LAN networks equipments.

Solid Copper Cable Cat 6, 4 pair, UTP - 305m SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supplying including installation of UPS

3 KVA On-Line UPS System (Orion or equivalent make as approved by the Deptt.) with PWM-IGBT technology230V AC Input (160V – 280V A 1 Ph input- 1 Ph outputWith Isolation Transformer 2.4KW output with 0.8 output PF, 120 min backup using SMF battery

LUMANARIES

Supplying with fitting fixing of CFL/Fluorescent luminaries complete with all accessories such as ballast, starter etc. directly on wall / ceiling including connection as approved by the Deptt.)with 1.5 sq mm P.V.C. insulated S.C. copper conductor as required and as directed by the department.

APFC (ABB/ SCHNEIDER/ CROMPTON GREAVES/ C&S/ SIEMENS/ L& T OR EQUIVALENT MAKE AS APPROVED BY THE Deptt.)

Supplying including installation testing and commissioning of 200kVAr, 440V APFC Panel Non-Compartmentalized Type, Free Standing, Floor Mounted

rated output 200k var

rated voltage 440 V

rated frequency 50 Hz

Number of phases 3 phases

Switching Option Auto Manual

ENCLOUSURE DETAILS

Materials CRCA

Thickness of sheet steel Frame & Doors: 2.0mm, Partitions: 1.6mm, Gland plate: 3.0mm

Dimensions W x H x D (mm) 800 x 1800 x 600 (Approx) + (250 mm for plinth & fan hook

Ingress Protection IP 42

Intallation Type Indoor

Cable Entry Button

Color ral 7035-Light grey

BUSBAR DETAILS

Material aluminium

Cross section(mm) 40 x 10 x 1 Run

Bus-Bar support DMC moulded

Capacitors

Heavy Dutiy @ 440 V

No of steps 6

Incomer MCCB,400A,36 Ka-CVS type

Switching capacitor duty contractors

Step protection MCB/MCCB

APFC RELAY

INCOMMER MCCB, 400 A, 36 KA CVS type

Digital volt-Amp,Freq metre 1

Phase indicating lamps (L1,L2,L3) 3

Current Transformer - 400/5A

APFC Relay 1

Control Curcuit Protection-MCB 2

Step Indicatin Lamps 12

On /off Push Buttons 12

Step Protection -MCCB,CVS type,25 KA- 100A 1

RISING MAIN

Supply of following capacity TPN with 100% neutral ,1000V, 50 Hz , IP-55 Compact Air-Insulated Bus Bar Trunking compliance with IEC 60439 with Busbar made from Aluminium alloy with Copper + Tin coating over whole length of Busbar insulated and supported by Insulating materials in regular interval with ''omega shaped'' ribbed sealed section housing of size mentioned below made from Hot-galvanized steel of 0.8mm thick with having Plug-in -outlets in every 500mm, IK-10 category of mechanical strength including junction monobloc, joint cover, end cover, supports with GI earth bar and design is compliance with IEC 60439 I & II. (Legrand/ C&S or equivalent as approved by the Deptt.)

250 amps Rising Mains ( SC rating for 1 sec- 8KA,

630 amps Rising Mains ( SC rating for 1 sec- 36K

Supply of following capacity End Feed Unit made of 1.6mm thick sheet steel enclosure duly painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/ C&S or equivalent as approved by the Deptt.)

250A End Feed Unit (W/0 MCCB)

630A End Feed Unit ( W/0 MCCB)

Supply of following capacity TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains with provision of fixing MCCB/HRC fuse . (Legrand/ C&S or equivalent as approved by the Deptt.)

63A Tap-off Box with inbuilt Disconnection (Legrand/ C&S or equivalent as approved by the Deptt.) on Cover ( W/0 MCCB/HRC fuse)

125A Tap-off Box with inbuilt Disconnection (Legrand/ C&S or equivalent as approved by the Deptt.) on Cover ( W/0 MCCB/HRC fuse)

U. G. CABLE AND CABLE WORKS

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) .

3 & 1/2 Core A2XFY

150.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

300.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

CABLE GLAND, TERMINAL, TRAY, FLOOR RACEWAY

Supplying, installation of GI PERFORATED cable tray on wall or from ceiling including necessary channel, nuts and bolts, washer etc. as required as directed and specified by the department. (LEGRAND/ AKG /STRUTFAST make).

Size of Tray

Size of Tray 304

Size of Band 304

Size of tree 304

Non- schedule Items ( Internal Electrical Works)

MAIN LT PANEL-[ INSTITUTE BUILDING ]

Incommer:

1250 A,4 P,MCCB,50KA-1 no

400 A, 4P, MCCB, 36 KA-2 Nos

400 A, 4P, On-load change over switch 1 no

Digital Ammetre metre 2 Nos

Digital Voltmetre 2 Nos

CT 400 /5-2 Sets

CT 1250 /5-1 Set

Switch Fuse Unit - 6 Nos

LED indicating Lamp - 2 Sets

Bus-Bars:1600 A TPN Electrolytic Copper Bus Bar of unform cross Section ( 100 mm x 10 mm) -1 sets

Bus-Bars: 800 A TPN electrolytic Copper Bus Bar of uniform cross-section (50mmx10mm) – 1 set

Outgoing :

630 A ,4P, MCCB, 36 KA - 1 No.

400 A ,4P, MCCB, 36 KA - 2 Nos.

250 A ,4P, MCCB, 25 KA - 4 Nos.

40 A 4P MCCB 25 KA – 2 Nos.

63 A 4P MCCB 25 KA – 4 Nos.

100 A 4P MCCB 25 KA – 2 Nos.

160 A 4P MCCB 25 KA – 2 Nos.

40A 4P MCB -3 Nos.

32A DP MCB - 3 Nos

Analysis

Supplying, installation, testing and Commission of the following indoor LED Decorative Surface Square typed optics down lighter luminaries complete with all accessories such as ballast, starter etc. directly on wall/ceilling including connection mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department

Square type Superior finish extruded white powder coated pressure die cast aluminium body with High transmitivity, non Yellowing PMMA diffuser with driver and accessories pre-wired upto terminal block assembly. LED Luminaires of make WIPRO Cat No. IrisLED Slim SQ SM LD81-171-XXX-60-SM LED 18W or equivalent inlcuding lamps etc. complete [CLT]

Analysis

Supplying, installation, testing and commissioning of the following LED luminaries complete with all accessories such as ballast, starter etc. in the ceiling including Y type suspension arrangement as specified by the manufacturer, and fixing the same on ceiling by perfect arrangement for load bearing as well as, to be match with the colour and design of the ceiling, of required length [max. 1.5 m] including making necessary connection cable, as approved by the Deptt.)with 1.5 sq mm.PVC.insulated.S.C.copper conductor as required and as directed by the department. department.

Slimmest Suspended Superior finish extruded white powder coated pressure die cast aluminium body with High transmitivity, non Yellowing PMMA diffuser with driver and accessories pre-wired upto terminal block assembly. LED Luminaires of make WIPRO Cat No. AuraPlusLED CRCO13R038HP57G1 31W or equivalent inlcuding lamps etc. complete [DTL]

Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade

Supply, Fitting Fixing of Shock Treatment Chart

Extarnel Electrical Works

Earthing

Supply, installation & testing of G.I. earth station with perforated 40 mm dia and 4.50 Metre long heady duty G.I. pipe with necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement 300 mmx300 mmx6 mm hinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt (5 K and Charcoal (64 K in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the Deptt.

Supply, installation & testing of Copper Plate earth station with 600 mmx600 mmx3 mm copper earth plate with necessary 40 mm dia. G.I. medium duty watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm C.I. hinged cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt (5 K and Charcoal (96 K in G.I./Copper plate Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the deptt .

Supplying & laying of 6 SWG G.I. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 25X5mm size G.I. strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 25X5mm size Copper strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of Brass nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

STREET LIGHT LUMINAIRES AND PANEL BOARD

Supplying with fitting & fixing of the following road lighting luminaries complete in the existing pole with high power LED and extendable up to with unique peanut lens to ensure uniform distribution including making necessary connection as approved by the Deptt.)with 2× 2.50 sq.mm F.R. multistrand and P.V.C. insulated single core copper cable as specified and directed by the department.

Supplying and installation and commissioning of vermin and dust proof totally enclosed double door cubical type compartmental floor mounting panel board of size 1.20 m ×1.00 m ×0.50 m made of 16 SWG1.66mm) thick CR sheet and 35 mm × 35 mm × 6 mm size angle and 35 mm ×6 mm flat iron having 4 nos legs at the bottom and G.I. Sheet reefing on the top complete painting with 2 coats of red oxide metal primer and 2 coats of enameled paint. The panel board is to be erected in 1:3:6 RCC pole foundation including excavation of trench and brick soling etc. complete neatly internal wiring done as specified and directed by the department comprising of the following electrical items.

1. 40 Amp 4 pole 415 Volt 50 Hz MCCB as incomer - 1 no

2. 32 Amp 2 pole open execution with HBC fuse SDFU unit as outgoing - 3 nos.

3. 25 mm × 5 mm size 4 strip copper Bus-Bar- 1 set

4. 40 Amp 4 pole ON-OFF poser contactor - 1 No.

5. Surface mounting timer switch - 1 No.

6. 63 Amp bakelite HBC fuse kit-kat - 3 Nos

LUMINARIES

Supplying fitting and fixing of LED post top lantern BGP150 LED1000/WW PSU 220-240V 7043 42 w protection IP 65 /IK 10 / Class 1 Philips make on existing GI pipe pole with foundation.

U. G. CABLE AND CABLE WORKS

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) .

3 Core A2XWY A2XFY

4.00 Sq.mm 3 Core armoured U.G. cable

6.00 Sq.mm 3 Core armoured U.G. cable

3 & 1/2 Core A2XFY

25.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

185..00 Sq. mm.3 & 1/2 Core armoured U.G. cable

300.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988, LT armoured U.G. cable laid in pucca flooring, road crossing, drain crossing as per site requirement and partially in air to connection as approved by the Depts. the control switch, through medium duty G.I. pipe (Tata/ Nezone make or equivalent as approved by the Deptt) bend and socket including excavation and refilling the trench and making good damage done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make)

Core - 3 A2XWY A2XFY

4.00 Sq.mm 3 Core U.G. cable in 25mm dia medium duty G.I. pipe

6.00 Sq.mm 3 Core U.G. cable in 32mm dia medium duty G.I. pipe

Core - 3 & 1/2 A2XWY A2XFY

25.00 Sq.mm 3&1/2 Core U.G. cable in 40mm dia medium duty G.I. pipe

185.00 Sq.mm 4 Core U.G. cable in 80 mm dia medium duty hot dip galvanised pipe (AKG or equivalent as approved by the Deptt.)

300.00 Sq.mm 4 Core U.G. cable in 100mm dia medium duty hot dip galvanised pipe (AKG or equivalent as approved by the Deptt.)

Supplying including installation of cast iron cable marker as specified and directed by the deptt.

CABLE KITS

Supply including fitting and fixing of 1.1 KV PVC/XLPE cable INDOOR/OUTDOOR end termination Kits (Raychem RPG make) HEAT SHRINK TYPE including all accessories for the following sizes including testing and commissioning as specified and directed by the Deptt.

185-300 Sq.mm., 3/ 3.5/ 4 Core cable.

OVER HEAD LINE

Supplying and fitting fixing of H.T. danger plate complete as required and as directed by the department.

OCTAGONAL POLE

Supplying including installation of the Octagonal poles shall be designed to withstand the maximum wind speed of 169 km/hr. The top loading i.e. area and weight of fixtures are to be considered to calculate maximum deflection of the poles and the same shall meet the requirement of BS:5649 Part VI 1982. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding of the pole shaft. The welding of the pole shaft shall be done by Submerged Welding process. All octagonal pole shafts shall be provided with the rigid flange plate of suitable thickness with provision for fixing 4 foundation bolts. The base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside. The welding shall be done as per process approved by Third Party Inspection agency. (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make)

Pole Type BOP or equivalent-1030 Height 10 m The materials of the pole as follows : Conforming to grade S355JO Conforming to grade S355JO, Base Plate :- Fe 410 Conforming to IS 226/ IS 2062, Foundation Bolts :- 6.8 Gr. As per IS 1367, Pole Sections:- The Octagonal Poles shall be in single piece with single longitudinal welding join. Galvanization :- The poles shall be hot dip galvanized as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 65 micron. The galvanizing shall be done in single dipping. Door opening :- The Octagonal poles shall have door of approximate 500 mm length at the elevation of 500 mm from the base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connection as approved by the Depts.. The door shall be flush with the exterior surface and shall have suitable locking arrangement. The pole shall be adequately strengthened at the location of the door compensate for the loss in section. There shall also be suitable arrangement for the purpose of earthing, Smart pack Junction box with 6 MCB & Terminals for mounting inside base compartment of Pole. Top Dia. :- (A/ 70, Bottom Dia.:- (A/ 175, Sheet Thickness :- 3mm, Base Plate Dimensions :- (L x B x 275 x 275 x 16, Foundation Bolt Size:- (no. x dia.) 4 x 24 Dia, Pitch Circle Dia. (PC :- 270, Bolt Length:- 750, Projected Bolt Length :-125, Anchor plate thickness :- 4 mm, Pole Foundation :-The octagonal poles shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. Foundation :- The foundation shall be done with ( Earth work :- 2.04 cubic Meters.RCC :- 1:1.5 : 3 proportion 0.65 cubic metres. Steel:- 22.43 Kg. Shuttering :- 4.32 square metres. = 22.43 Kg.

Supplying including fitting and fixing of Hot Dip galvanised arm bracket for installation of luminaries. Header with top cap 300 mm long pipe of thickness 3 with arrangement to fix on pole top with 3 Nos. of bolts. i Armed of required length size 48.3mm out side dia x 3.25mm thick (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) Stiffener plate from arm of the following types :

Single arm bracket 1500mm long for 3m to 10 metre. Poles.

Motor Pump Set

Supplying including installation, connection as approved by the Deptt., testing and commissioning of CENTRIFUGAL MONOBLOCK PUMP SET complete as directed and specified by the deptt.

3 HP single Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) 2900 rpm with DOL Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) .

Supplying including installation, connection as approved by the Deptt., testing and commissioning of SUBMERSIBLE PUMP SET 3 (Three Phase) with steel cable rope and submersible cable complete as directed and specified by the deptt.

Three phase Submersible motor pump set (Texmo / Crompton Greaves/ Aquatic/ CRI/ V-Guar suitable for 100 mm bore well and above. 3 HP STAGE 7 to 40 with MCB controlled Submersible motor pump set control panel.

NON-SCHEDULE ITEMS ( EXTERNAL ELECTRICAL WORKS )

Fabrication, supply and erection of 4.5 Mtr. Long 75mm dia MS pole with MS base plate of 300x300x10mm thickness at the bottom of the pole with fixing arrangement for post top lantern and to accomodate a junction box. The foundation is of cement concrete of 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate) size 0.8 x 0.8 x .35 m with collar of size 0.4m dia x 0.5m height to accomodate the looping type cable end box including excavation and refilling etc. as required. The pole shall be painted with one coat of red oxide primer and two coats of aluminium paint.

Supplying with fitting and fixing sheet steel cable junction box of size 40cm x 20cm x 15 cm made of 16 SWG thick MS Sheet with provision for hinge door and panel locking arrangement complete painted with 2 coats of metal primer and 2 coats of enamelled gloss paint of approved brand and manufacture to give an even shape including cleaning surface to remove of all dirt, dust and other foreign matter, the box is to be fitted on the bottom section of pole with minimum 165 mm dia 25 mm x 5mm size flat iron pole clamp complete with making necessary connection as directed consisting of the following electrical items.

12mm x 2mm x 15cm long 2 strip copper Bus Bar - 1 set

6-32 Amp "L" series DP MCB - 1 No.

6 amp "L" series SP MCB as outgoing - 2 Nos.

Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade

Supply, Fitting Fixing of Shock Treatment Chart

SOLAR ELECTRICAL SYSTEM

SOLAR POWER

Supplying including installation, testing and commissioning of Solar power plant as per following specification and as directed by the Department.

5.12 KWp STANDALONE SOLAR POWER PLANT Load: 4000 Watts for 4 Hrs/Day Back up Or, Load: 2000 Watts for 8 Hrs/Day Back up

1. Crystalline Solar PV Module - TBP1280M/ TBP1280 with RDSO Part-I Approval (as per IRS S: 84/92 or latest Amdt.) & IEC: 61215 Certification. 64 nos

2. 4 Module mounting structure with theft proof frame 16 nos

3. Array Junction Box (AJ 2 nos

4. Main Junction Box (MJ 1 no

5. Power Conditioning Unit (PCU) – 96V DC- 5KVA- 230V AC, 50Hz 1 no

6. Battery Bank- Tubular Plate LMLA Battery Bank of 96V, 400Ah @ C10 1 set

7. 2C X 2.5 Sq.mm. P.V.C Cu.cable 300 metres

8. 2C X 6.0 Sq.mm. P.V.C Cu.cable 100 metres

9. 2C X 10 Sq.mm. P.V.C Cu.cable 30 metres

10. 1C X 25 Sq.mm. P.V.C Cu.cable 30 metres

11. 1C X50 Sq.mm. P.V.C Cu.cable 15 metres

12. Earthing kit 6 nos

14. Installation kit 1 set

Note: All cable lengths are estimated. Extra cables, if any, shall be charged extra at actual. All cable

Lengths are calculated from the Solar Array to input of the Power Conditioning Unit (PCU). Loads &

Load cables are not included in the Bill of Materials.

SUGGESTED UNIT PRICE

Unit Cost Without Installation & Commissioning)

Installation & Commissioning Charges

NON-SCHEDULE ITEMS SOLAR

Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade

Supply, Fitting Fixing of Shock Treatment Chart

For Lift

Supplying installation, testing and commissioning of 13 passenger (884 Kg.) passenger lift of car size 1600 X 1350 mm, MRL Gear less, stainless steel hair line finished, machine room less centre openning power door with autometic recue divice and lift announcment systems. The lift having contract speed of 1 MPS serving different floors in the lift shaft as per detailed specification enclosed and as under:

1. No. of Elevators 1 No.

3.Capacity Passanger -13 Persons-884 KG

4.Speed 1 m per sec(Approx)

5. Control Variable Frequency with speed encoder.

6. Operation Simplex Full Collective Control.

7. Controller Microprocessor based modular control system ( Location door column at top floor

8. Communication Loop type serial communication

9. Travel GF to 6th Floor , about 24.0 Metres.

10. Stop & Opening 6Stops 6 Levels 6 Openings (All opening on the same side

11. 10. Power Supply 400 V ± 10% variation ,three-phase 50 Hz ± 5% variation

12. Machine Gearless with permanent magnet motor located in the shaft at top.

13. Rope Flat poly urethane - coated belts

14. Cab finish Stain less steel hair line finished

15. Cab ventilation Pressure fan

16. Cab Size 1600 mm Wide x 1350 mm Deep approx.

17. Shaft size required 2250mmx 1950mm

18. Entrance type Centre opening.

19. Fire rating One hour fire rated.

20. Entrance opening 900mmx 2000mm

21.Over head 4000mm

22. Pit depth 1800mm

23. Entrance protection system High Performance contact free infra red curtain - 2 dimensional

24. Door operation Power operated automatic sliding doors.

25. Door operator DC door operator system.

26. Human interface device (H

Hall button with micro stroke push buttons combined digital LED display position indicator.

Full height car operating panel with micro stroke call push buttons (located on side panel)

Door open and door close button on the car operating panel.

Dot matrix position indicator display integrated with the car operating panel.

Battery Operated Emergency Alarm and Light.

Fireman's switch at main lobby

Automatic rescue device.

Supplying installation, testing and commissioning of 8 passenger (544 Kg.) passenger lift of car size 1100X 1300 mm, MRL Gear less, stainless steel hair line finished, machine room less centre openning power door with autometic recue divice and lift announcment systems. The lift having contract speed of 1 MPS serving different floors in the lift shaft as per detailed specification enclosed and as under:

1. No. of Elevators 1 No.

3.Capacity Passanger -8 passenger (544 Kg.)

4.Speed 1 m per sec(Approx)

5. Control Variable Frequency with speed encoder.

6. Operation Simplex Full Collective Control.

7. Controller Microprocessor based modular control system ( Location door column at top floor

8. Communication Loop type serial communication

9. Travel GF to 6 th Floor , about 15.0 Metres.

10. Stop & Opening 6Stops 6 Levels 6 Openings (All opening on the same side

11. 10. Power Supply 400 V ± 10% variation ,three-phase 50 Hz ± 5% variation

12. Machine Gearless with permanent magnet motor located in the shaft at top.

13. Rope Flat poly urethane - coated belts

14. Cab finish Stain less steel hair line finished

15. Cab ventilation Pressure fan

16. Cab Size 1100 mm Wide x 1300 mm Deep approx.

17. Shaft size required 1900 mmx 1800 mm

18. Entrance type Centre opening.

19. Fire rating One hour fire rated.

20. Entrance opening 900mmx 2000mm

21.Over head 4000mm

22. Pit depth 1800mm

23. Entrance protection system High Performance contact free infra red curtain - 2 dimensional

24. Door operation Power operated automatic sliding doors.

25. Door operator DC door operator system.

26. Human interface device (H

Hall button with micro stroke push buttons combined digital LED display position indicator.

Full height car operating panel with micro stroke call push buttons (located on side panel)

Door open and door close button on the car operating panel.

Dot matrix position indicator display integrated with the car operating panel.

Battery Operated Emergency Alarm and Light.

Fireman's switch at main lobby

Automatic rescue device.

RAINWATER HERVESTING SYSTEM

For R.C.C Roof

Providing,Fixing, testing &Commissioning of Rain water Hervesting system for 1000 sq.feet roof area with 110 mm uPVC pipe of Class-3 conforming to IS:4985-200 (with uptodate amendment) with extra UV ray protection by Titanium Dioxide(TiO2) directing the Rainwater to Rainy filter/Pop-up raintap filter (Excluding Civil Works)

Storage of Rainwater

Water storage tank ISI Marked, conforming to IS:12701/1996 (with uptodate amendment). (Excluding Civil Works)

FOR LANDSCAPING

HEDGE PLANTING / EXTERNAL HEDGE

Supplying and planting of suitable plant materials for preparation protective / external hedge (50 cm wide) including the preparation of the ground by mixing organic manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed .

(A) ADOPTING SINGLE ROW PLANTING METHOD

(iii) With Chinese Bamboo

(B) ADOPTING CROSS WISE DOUBLE ROW PLANTING METHOD

(iii) With Chinese Bamboo

TREE PLANTING

Supplying and planting of ornamental trees (1'-0" height sapling) including pit making ( 60 cm x 60 cm x 60 cm ), filling the pit with appropriate soil media, manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed .

SHADE TREE

(A) Neem / Mahaneem / Beef wood / Bakul / Acacia / Siris / Devils tree / Kadam / Palash / Pink Cassia / peepal / Silver oak / Simalu / Ajar

T N T Projects Ltd

Shree Gautam Construction Co Ltd

M/S D.S. Trading

GANESH TAMULI ENGINEERING PRIVATE LIMITED

M/s Sanwarmal Khetawat