SPL REPAIR TO ROOF TREATMENT AT PC 05 HOSHIYAR SINGH HALL CONNECTED ROOFS AT SW DIV AND PROVN OF CERTAIN MINOR AND REVENUE WORKS UNDER GE MIS MHOW

Amount

Surface dressing n exc. 30 cm deep and avaraging 15cm deep and getting out in soft/loose complete all as specified and as directed.

Excavation over areas in any type of soil n exc. 1.50m deep and getting out complete all as specified and as directed.

Excavating in trenches n exc. 1.5 m wide and n exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc. 10 sq m on plan and n exc. 1.50 m in depth and getting out in soft/loose soil complete all as specified and directed.

Removing excavated material (soil) to a distance not. exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Returning, filling in, excavated soil including, spreading, leveling, watering and well ramming in layers not exc. 25cm complete all as specified and as directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering as required complete all as specified and directed.

M&L broken stone or boulder hardcore gauge n. exc 63mm, deposited spread and levelled in layers n exc 15mm thick, watered and rammed to true surface complete all as specified and directed.

M&L for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete and sub base of floor complete all as specified and directed.

M&L for Cement concrete (1:3:6) type C2 (using 40mm graded stone aggregate) in filling sub base, base complete all as specified and as directed.

M&L for reinforced cement concrete (M-25) Design mix as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and the like complete all as specified and directed.

M&L for reinforced cement concrete (M-25) Design mix as in Slabs supported on walls, ,chajjas, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for reinforced cement concrete (M-25) Design mix as in roof beam, plinth beam,roof beam, lintel beams and Columns complete all as specified and directed.

M&L for reinforced cement concrete (M-25) Design mix as in chajjas complete all as specified and directed.

M&L for reinforced cement concrete (M-25) Design mix as in Columns, footing, pillars, piers, posts and struts complete all as specified and directed.

S&F Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, footing, roof beam, plinth beam, slab,chajjas and similar work hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 15.00 above but 5 mm dia and over up to and including 10 mm dia as in stirrups complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc. complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc. complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc .complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc. 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for Brickwork with modular fly ash bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar (1:4) complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:6 on brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for glazed ceramic coloured tiles 450mm x 300 mm size 6 to 7mm thick in dados or skirting over & including rendering 10mm thick in cement mortar (1:4), jointed in neat grey cement slurry and pointed in white or colour cement to match the tiles complete all as specified and directed.

M & L for Non skid ceramic tiles coloured, 7 to 8 mm thick (Square / rectangular ) area of each tile exceeding 0.11 Sqm but n. exc 0.18 Sqm, over & including 20mm thick screed bed in CM (1:6) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles complete all as specified and directed.

S&F second class hard wood 35 mm thick Plain , framed panelled factory made shutters (any number of panels), with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as specified and directed.

S&F second class hard wood 35 mm thick Glazed and skeleton factory made shutters, open rebated and prepared to receive glass , gauze, etc, (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) fitted to chowkats complete all as specified and directed. Note :- Glass pane and wire mesh shall be measured and paid separately in respective supply only item.

S&F stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F 100mm long butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F 150 mm long Aluminium anodizes barrel tower bolts of extruded section complete all as specified and directed.

S&F Mild steel pressed handles 150 mm, oval type, stove enamelled black complete all as specified and directed.

S&F 250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and directed.

S&F 300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate complete fixed to steel frame / wooden frame including necessary welding, cutting, opening of wall for fixing bracket and making good complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 20mm graded stone aggregate) as in plinth protection Finishing surfaces of concrete topping even and fair (without using extra cement) including making joint at every 3.00m interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of Ist quality exterior weatherproof water base emulsion paint over a coat of primer of same make on wall as specified and directed pillasters, cornices etc including scrapping down , brooming down or steel wire brushing, and washing with water complete all as specified and directed. Note :- (a) Each stage i.e preparation of surfaces, application of primer, application of first coat and application of second coat will be got passed from Engr-in-Charge/GE. (b) Written Warranty for four years or as per manufacturer's instructions, whichever is more is required to be furnished by contractor for this item.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistance primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash on ceiling surface complete all as specified and directed.

S&F steel window with side hung shutters including box type hinges with steel handle and steel peg stay complete with glazing bars/guard bars dovetailed or welded complete all as specified and directed.

All as per Item No. 39.00 above but without glazing bars complete all as specified and directed.

S&F steel ventiletor with top hung shutters including hinges,steel peg, peg stay complete with glazing bars complete all as specified and directed.

S&F mild steel framed work such as grills , gratings, etc., with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars ; barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for providing and applying minimum 1mm thick wall care putty over prepared surface to achive the surface even and smooth for painting complete all as specified and directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment laid over and including 50 mm thick stone dust cushioning laid dry to the profile complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over of redoxide zinc chrome coat complete all as specified and directed.

S&F wash hand basins, vitreous china,of size 550x400mm (flat back, or angle back type) including cutting for and pinning in ends of brackets or erecting stand including waste pipe and CP coupling etc complete all as specified and directed.

S&F padestal pattern vitreous china wash down water closet pan white including trap, PVC seat cover white and flush pipe and connection to drain (or out going pipe) and flushing pipe antisyphone pipe etc complete including trap and complete all as specified and directed.

S&F PVC valveless, syphonic action type flushing cistern,low/high level white with inlet ball valve float and handle including brackets complete fixrd in repair capacity of flush 10 ltrs complete all as specified and directed.

S&F 75 mm bore PVC floor traps plain with grating and 300 mm long out let including jointing and etc complete all as specified and directed.

S&F PVC bends 75mm bore, any radius complete all as specified and directed.

S&F PVC (SWR) pipes of dia 110 mm single socketed in any length with rubber ring joints laid in trenches or in floors of dia 110 mm complete all as specified and directed.

S&F PVC (SWR) pipes of dia 75 mm single socketed in any length with rubber ring joints fixed to walls of dia 75 mm complete all as specified and directed.

S&F Bib taps (push type) cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm bore, complete all as specified and directed.

S&F fancy type chromium plated two way bib cock of 15mm bore ,screwed for iron pipe or brass ferrule etc complete all as specified and directed.

S&F pillar taps (swan neck), fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F brass stop/angle cock cast copper alloy high pressure, angle valve type, chromium plated suitable for 15mm bore steel pipe complete all as specified and directed.

S&F SS tubular towel rail, 60 cm long, 20mm bore, complete all as specified and directed.

S&F SS Toilet paper holder complete all as specified and directed.

S&F health faucet with S.S. flexible pipe of 1.00 to 1.50 metre length including holder complete all as specified and directed.

S&F PVC connections of 450mm long suitable for 15mm dia iron pipe including PTMT nuts complete all as specified and directed.

S&F 15mm bore tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified and directed.

All as per serial item No. 61.00 above but 20mm bore complete all as specified and directed.

S&F Gun-metal, globe or gate valves 15mm, with iron wheel head ,screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F rotational moulded polythylene 500 Ltr capacity water storage tank (double layer)(cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F factory made PVC door frames of sizes 50 x 47 mm made out of 5 mm prelam PVC sheet reinforced with MS Square tube in opening of suitable size complete all as specified and directed.

S&F Factory made (Prelam on both sides) solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall covered with heat moulded prelam PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and prelam PVC sheets for top rail, lock rail and bottom rail in either side and as gap insert for top rail and bottom rail pannelling of prelam PVC sheet to be filled in the MS welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together wiht solvent and fixing in the frame at site as per specification and drawing complete all as specified and directed.

M&L for preparation of surfaces for applying bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete all as specified and directed.

M&L for applying a tack coat of Industrial bitumen grade of 85/25 at the rate of 1.20 Kg per Sqm including cleaning surfaces (one coat for bonding material below membrane) complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified and directed.

M&L for applying two coats of bitumen based aluminium painting @ 0.15 Kg / sqm each coat on water proofing treatment with preparation of surface as on non assesible area complete all as specified and directed.

Supply and laying NP-2 pipes 150mm bore, laid and jointed complete with collar per length of pipe complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment laid over and including 50 mm thick stone dust cushioning laid dry to the profile complete all as specified and directed.

M&L for taking down/dismantling of existing roof treatment of any description such as old APP membrane roof treatment etc terracing including screed bed/plastering etc. Hessian base felt/tar felt etc. (any type and thickness) complete all as specified & directed.

M&L for Brushing with neat cement slurry @ 3 Kg per Sqm area complete all as specified and directed.

M&L for cement concrete 25mm thick type B-1, 1:2:4 (12.5mm graded stone aggregate) as in roof top without using extra cement etc complete all as specified and directed.

M&L for screed bed 15mm thick in cement mortar 1:4 mixed with integral water proofing compound while concrete surface is green and finish the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately

Taking down cement plaster from brick or concrete surface including racking out joints hacking for key and scrubbing down with water complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:4 mixed with integral water proofing compound while concrete surface is green and finish the surface even and smooth without using extra cement all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for rendering 5mm thick in cement mortar 1:3 mixed with integral water proofing compound while concrete surface is green and finish the surface even and smooth without using extra cement complete all as specified and directed Note:- WPC shall be measured and paid separately.

M&L for Cutting out cracks to V- section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and directed

M&L for applying a tack coat of Industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces (1st coat for bonding material below membrane and 2nd coat on top of membrane complete all as specified and directed Note: Each coat will be measured and paid.

Supply only liquid water proofing compound complete all as specified and directed

S&F in repair 15mm GI tubing medium grade with all fittings & fixed complete to walls /ceiling or laid in floors all complete all as specified and directed.

All as per item No 85.00 bove but 25mm bore GI tubing.

S&F in repair rotational moulded polythylene water storage tanks(double layer), 500 Ltrs capacity, (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 25mm bore complete all as specified and directed.

S&F in repair of rotational moulded polythylene water storage tanks(double layer), 1000 Ltrs capacity, (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 25mm bore complete all as specified and directed.

M&L for preparation of old/new surface and applying two coats of 100% Premium arcylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance , dirt resistance exterior paint of required shade (Company Depot Tinted ) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. Note- Painting work to be carried out through air less spray machine (Mechanical means)

M&L for preparation of old/new surface and applying two coats of distempering with Ist quality acryalic distemper (ready mixed) having VOC content less than 50 gms/ltrs, of approved manufacturure,of required shade and colour complete as per manufacturur specification complete all as specified and directed.

M&L for preparation of old treated surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation and removing of old treated steel surfaces of any description exceeding 10cm in width or girth and applying two coat of synthectic enamel paint complete all as specified and directed.

M&L for preparation of old treated wood or wood based surface of any description exceeding 10cm in width or girth and applying one coat of synthectic enamel paint complete all as specified and directed.

Demolition of brick work / stone boulders masonry built in cement mortar incl all Quoins , archeas, pillars etc but exc cluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

Demolition of cement concrete n exc. 15 cm depth of any description and in any position not otherwise specifically provided (below or above ground level) including removal of concrete debris from site up to 500 metre all as specified and directed.

Formwork to faces of walls, retaining walls, abutments parapets and staircase railing and similer work including attached pillasters, buttresses etcvertical or to batter all as specified and directed

M&L for reinforced cement concrete (M-25) Design mix in walls, reatining walls basement walls, ballest walls and the like any thicknes; above top of footing; including attached pilasters and buttresses complete all as specified and directed.

M&L for precast RCC 1:2:4 type B1 as in cover slab for manhole etc with plane faces complete all as specified and directed.

M&L for brick work with modular size burnt fly ash bricks, straight or curved on plan exc. 6 m mean radius built in cement mortar (1:6) complete all as specified

Dismantling of floor or herth tiles including cement mortar bedding but not backing all as specified and directed

M&L for light shade vitrified ceramic tiles 10mm thick ( Square/Rectanguler ) polished,area of each tiles not exceeding 0.36 Sqm in Floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and over and including cement screed bed 15mm thick in cement mortar 1:6 all as specified and directed.

M&L for light shade vitrified ceramic tiles 10mm thick ( Square/Rectanguler ) polished,area of each tiles not exceeding 0.36 Sqm in skirting/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and over a 10mm back coat plastering cement mortar 1:4 complete all as specified and directed.

Taking down shutter with frmae of any descriptionn exc. 1.50 sqm each complete all as specified and directed.

S&F powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed and one shutter wire mesh) shall be two part as upper patr shall be three movable shutter and lower part consist three shutter (one openable in centre and both side fixed type shutter with frosted glass) with following specification and making good the adjacent side of jambs of windows by plastering in cement mortar 1:3 even and smooth complete etc . shifting of existing cooler stand where required complete all as specified and as directed by Engr-in-charge:- (i) Windows frame of cross section 101mm x 44mm x 1.5mm thick. (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm x1.1mm thick. (iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick. (iv) 4 mm thick glass superior quality. (v) IDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 Nos. (vii) Sliding rollers per shutter - 02 Nos. (viii) Stainless steel wire cloth 0.30mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 Nos. (Ix) fixing screw for frame with wall per windows- 08 Nos.

Taking down frame with shutter of any description exc. 1.50 sqm but n exc. 4.00Sqm each complete all as specified and directed.

S&F anodised aluminum door air tight frame made of size 100mmX45mm,of sheet thickness 1.5mm with one or more rebate including jointing cleat etc for fixing anodised aluminum door shutter fully panelled ( two nos of panel of each shutter) with 5.5mm thick tinted glass shutter,rail made 80mmX45mm of sheet thickness 1.5mm ( top,bottom,midle and side rail) single/double leaf side hung type including necessary jointing cleat,anodised aluminum fillet,aluminium glazing clip with rubber gAasket with aluminum fitting such as aluminium butt hinges 100mm long 3Nos on each shutter,aluminum anodised handle150mm,2 Nos D type for each shutter and locking 6 lever Make : Harrison one on each door, All door fitting except cleat shall be ISI marked.

S&F plain solid stright chowkhats and frames,wrought framed rebated on the solid,rounded or chemfered,put togather with glue pinned at joints complete all as specified and directed.

S&F 19mm thick priliminated particle board both sides with decorative choice including necessary second class hard wood 6mm edging for cup boardcomplete all as specified and directed.

S&F continuos (Piano) hinges mild steel, bright finish or electrogalvanized 30mm width flap ( When open) type complete all as specified and directed.

Dismantling of wall or ceiling boards ( Fibre,pulp insulatiion etc) or insulation boards/slabs/blankets any thickness including cover fillets all as specified and diretced.

M&L for providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns pinhole 8mm thick semi perforated square edge tile having NRC (Noise Reduction coefficient) of 0.50 (minimum) Light reflectance of 85% (minimum). Non combustible as per BS: 476 (PART-4), fire performance as per BS : 476(PART 6 & 7 ), humidity reistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, in true horizontal level suspeded on interlocking metal powder coated T-Grid of hot dipped galvanized iron section on Silhouetter profile, rotary stitched double webbed white with 1 mm reveal profile (White/black), comprising of main-T runner of size 15 x 32mm of length 3000m, cross - T of size 15 x 32 mm of lenght 1200mm and secondary intermediate cross-T of size 15 x 32 mm of lenght 600mm to form grid module of size 600 x 600 mm, from ceiling using galvanized mild steel item, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod and L-shape level adjuster of size 85x25x2 mm. Galvanized iron perimeter wall angle of size 19 x 19mm of length 3000 mm to be fixed on periphery wall /partition with the help of plastic rawl plugs at 450mm centre to centre and 40mm long dry wall S.S. screws. The work shall carried out as per specifications, drawing and as per directions of the Engineer-in-Charge .

S&F in repair decorative design (groves) solid PVC wall lining consisting of 5mm thick wood grain (primium quality) PVC sheet inclusive of solvent cement and fixing at site on PVC frame including 5mm thick PVC shee fillet of width 35mm for wll panelling inclusive of fixing on to wall t Make PVC frame and 5mm thick printed colour PVC sheet in corner,strips & channel feathered at the edges complete all as per specification and drawing complete all as specified and directed.

Excavating in trenches n exc. 1.50 m wide and n exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc. 10 sq m on plan and n exc. 1.50 m in depth and getting out in hard/dense soil complete all as specified and directed.

M&L for PCC (1:2:4) type B-2 ( using 40mm graded aggregate) as in embadding of fencing post complete all as specified and directed.

S&F framed brackets of angle or tees with web and flenges cut to shape,drilled and counter sunk for screw, including bending and welding angld as necessary gusset plates riviting etc N exc 10Kg each brackets,confirming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F pre-painted galvalume aluminuim zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strenght of 550Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

M&L for 100mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub abse of floor complete all as specified and directed.

S&F for 5 mm thick PVC false ceiling panells of size 600mmX600mm Plain embossed PVC sheet of density 600Kg /cbm manufactured by ISO certified company is stuck on both side with adhasive . The panel is inserted in a frame made of anodised Aluminium "T" section of size 1"X1" (25mmX25mm) in square type grid of size 2'X2' (600mmX600mm) The aluminium framework is supported from the ceiling with the help of 'J' hook and G I wire /6mm M.S rods of required sizes to maintain proper level. The aluminium framework is supported on side wall with help of aluminium "L" section of size 1"X1" (25mmX25mm) angles complete all as per direction of Engr-in-Charge,manufactur's specification & Drawing .

M&L for Granite 18-20 mm thick (of any type) work (table rubbed and polished) for wall lining (Veneering to wall) and laid on cill of parapit wall over 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite colour Red or brown complete all as specified and direceted.

M&L for cudappah stone slab 20-25mm thick in floor, riser of steps,skirting,dado screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed on cement mortar 1:4 complete all as specified and direceted.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in levelling course finished even and fair for laying floor finishes etc complete all as specified and direceted.

M&L for preparation of old/new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistance primer over and including 1 mm cement putty complete all as specified and directed.

M&L for preparation of old treated wood or wood based surface of any description exceeding 10cm width or girth and applying two coat of synthectic enamel paint complete all as specified and directed.

S&F rotational moulded polythylene water storage tanks(double layer), 1000 Ltrs capacity, (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 20mm bore complete all as specified and directed.

S&F 18 mm thick factory made PVC sheet one side pre-laminated sheet kitchen cabinet shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for marking edge lapping bending for 0.5 mm thick PVC sheet lapping at all four edges using bonding tape etc complete all as per specified and directed by Engr-in-Charge manufacturers specification .

S&F harrison rail/curtain rod, stainless steel with fixing bracket, stops and complete fitment complete all as specifed and as directed.

S&F PVC pipe of 40 mm dia, in any length and in any position such as walls, ceiling or laid in floor or trenches etc. complete all as specified and directed.

S&F PVC bend for 40mm dia PVC pipe complete all as specified and directed.

S&F 150 mm size stainless steel handles cast type, anodised ISI marked complete all as specifed and as directed.

S&F stainless steel self closing hinge of 75mm size for PVC door shutter complete all as specifed and as directed.

S&F mild steel drawer cabinet channel for moving the drawer etc complete all as specifed and as directed.

S&F 40mm flaps width (when open) continuous (Piano) hinges mild steel bright finish or electrogalvanised complete all as specifed and as directed.

S&F Powder coated aluminium work for door , windows , ventilator and partitions (fixed position) with extrded built up tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

M&L for point wiring using approved colour coding as as per IS with FR LSH PVC insulated PVC unsheathed electric cable 1100V grade ISI 694 marked down through single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping will be used) with GI modular sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches and blank plates & 1.5 sqmm green FR LSH PVC insulated unsheathed copper conductor as earth wire connected to earth dolly for the following . Make of PVC conduit / Casing Caping:- Plaza /Finolex /Polycab /Kalinga /Jindal/ Asian & Make of wire :- Havells /Finolex / HPL or other make as specifed in Particular Specification as approved by GE Make of Modular sunken Box, Modular plate and frame etc - Make as specifed in Particular Specification as approved by GE

(a) One light point/ceiling fan/wall fan/exhaust fan point controlled by one switch

(b) One 5amps socket out let point controlled by one switch on same board with other switches.

(c) One 5amps socket out let point on independent board controlled by one switch.

All as per item 135.00 above but using 2.5 sq. mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket combination point including necessary running of 2.5 sq. mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.

All as per item 135.00 above but using 4.0 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for geyser point/AC point connecting to metal plug and socket DB including necessary running of 4.0 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S&F Modular Switch flush type 6 Amps single pole, one way complete all as directed.

S&F Modular Socket outlet, multi purpose, 2/3 Pin combined 6 Amps flush type complete all as directed.

S&F Modular Socket outlet, multi purpose, 2/3 pin combined 16 Amps universal socket complete all as directed.

S&F Modular Switch 16 Amps single pole, one way complete all as directed.

S&F ceiling rose surface bakelite three terminal complete all as directed.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece, CP angle cock etc complete all as specified and directed by Engr-in- Cherge Make of water heater/Geyser - Bajaj / Havells / Jaguar / Crompton as approved by GE Make of fittings: Jaquar / Cera / Kohler / Marc / Prayag/ Gem as approved by GE.

M&L for plumbing work complete for geyser fittings ie GI tubing 15 mm dia length -5m, elbow, union, sockets including CP bib cock, etc concealed in wall by cutting chases of wall and making good disturbed surfaces complete all as specified and directed by Eng- in- charge Make of GI pipe: Tata/Jindal/ Surya Prakash /Swastik Make of fittings: Jaquar / Cera / Kohler / Marc / Prayag/ Gem as approved by GE.

S&F integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes including taking down the existing complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 / Bajaj cat Pt No. BCLSB 18WH or equivalent in Philips/Wipro as approved by GE.

S&F integrated LED tube light fitting 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square box including taking down the existing complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7IN1W009 Bajaj Cat Pt No. BCLSB 10 WH or equivalent in Philips/Wipro as approved by GE.

S&F LED street light fittings 1x30 Watt, 5700K complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible copper cable complete all as specified and directed. Make:- Crompton Cat No. LSTO-25-CDL / Bajaj Cat No. ENXTP30LWHSYPCSD or equivalent in Havells/ Philips/Wipro as approved by GE.

S&F double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engr-in-Charge.

S&F MCB TPN 40 to 100 amps 10 KA, c-series including connection with suitable size aluminium/copper lugs complete all as specified and directed by Engr-in-Charge.

S&F MCB SPN 6 to 32 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

S&F MCB SPN 40amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

S&F BLDC ceiling fans With Remote complete with blades, including down rods (as per site requirement),and accessories, 230 V, 1400mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five starrated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 250 mm including cutting of wall and duly connection with copper wire from ceiling rose etc complete all as specified and directed.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, etc . Removing materials to store for keeping in safe custody or for taking credit ( credit a for above items should be made as per condition seperately ) and making good distrubed surfaces of walls, floors etc.

Taking down old/ distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including MCCBs/ MCBs, Isolators, etc and refixing the same at same or different location as per site requirement and making good to disturbed surface all as specified and directed at site.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M complete all as specified and directed.

S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F Modular type Telephone socket outlet complete all as specified and directed.

S&F Modular type RJ 45 with shutter complete all as specified and directed.

S&F modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and directed.

S&F in repair LED ceiling light fittings 34/36 watt recess mounting type 2'x2' luminaire, 6000k (White Light /Warm white light as per site requirement ) complete with driver duly connection wire etc including taking down the existing complete all as specified and directed. Make Jaguar Cat No. LULT10S036XC / Crompton Cat No. LCTLRN-36-FO-CDL /Bajaj Cat Pt No. BZRSQL 36W GZ1 WH or equivalent in Havells /Wipro / Philips as approved by GE

S&F in repair integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes including taking down the existing complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 / Bajaj cat Pt No. BCLSB 18WH or equivalent in Philips/Wipro as approved by GE.

M&L for sub main wiring with two runs of single core FR LSH PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia in Conduit or concealed in wall by cutting chases of wall and making good the disturbed surface to matched with the existing surfaces complete, including PVC insulated unsheathed FR LSH 6.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge. Make of PVC conduit:- Plaza/ Finolex/ Polycab/ Kalinga/Jindal/Asian Make of wire - Finolex / RR Kabel Ltd / L&T/Havells or other make as specifed in Particular Specification. Note:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit and cutting chasing will be measured as one unit length.

S&F double door TPN DBs four way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engr-in-Charge.

S&F single pole and neutral Sheet Metal enclosure with a two pin and earth plug and socket complete with one single pole MCB 20/32 Amps incl cutting of wall and fixing of AC box in concealed system and making good of disturbed surfaces complete all specified and as directed.

Labour only for refixing the celing fan/ Wall fan/ Exhaust fan obtained from item No 2 above with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc. complete all as specified and as directed.

M&L for Earthing complete (in replacement) with galvanized steel earth plate electrode 60cm x 60cmx 6.3 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with the top edge of the earth plate not less than 1.50m below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No. 3 of MES SSR parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type C-1 with 40 mm thick RCC 1:2:4 type B-1 cover reinforced with 8mm dia TMT MS bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion complete all as specified and directed. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.50 m from earth plate is deemed to be included in rate quoted.

S&F LED luminaire 600 mm x 600 mm square LED panel 35/36 watts, 220 volts, lumen efficacy of 120 lumens/watt, AC Surface/recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling, including connecting up with driver three core flexible copper conductor cases of suitable size complete all as directed by Engineer- in-charge.

S&F LED light fitting 2 feet 10 watts, 6500K batten aluminium extruded with end caps complete all as specified and as directed. Make:- Cat No LHEXACP7IN1W010 of Havells make in Philips/Wipro/Bajaj/Crompton as approved by GE.

S&F Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make:- Cat No : BIBWP 10W LED of Bajaj make in Philips/Wipro/Havells/Crompton as approved by GE.

S&F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe 40 mm dia medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make:- Cat No ENXT P 36L WH CR PC SD of Bajaj or equivalent make in Philips/Wipro/Havells/Crompton as approved by GE.

S&F Highly efficient LED Bulbs, 06 watts semi circular in shape of transparrent polycarbonate body , one red and one green (ONE SET) in colour for indication. On modular / PVC sheet/ board complete all as specified and directed.

M&L for sub main wiring with 02 runs of 6 sqmm main wire along with 01 run of 06 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC concealed conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the same complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit and cutting chasing will be measured as one unit length. Make of cable - Havells / Finolex / RR Kabel Ltd. / L&T Make of PVC Conduit (FRLS) - Presto Plast / Finolex / Jindal / Asian / AKG

M&L for Sub main wiring with approved colour coding as per IS with four run single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq. mm nominal area and drawing into including suitable size of PVC FRLSH non metallic rigid heavy duty conduit of white/ ivory colour and its accessories ISI marked heavy duty of suitable size including concealed in wall etc two runs of PVC insulated with 6 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire including cutting chasing complete all as specified and as directed. Note:- Four runs of 6 Sqmm cable, two runs of 6 Sqmm cable, one run of PVC conduit and cutting chasing will be measured as one unit

S&F PVC non-metallic rigid Cable /Lan wire Ducts/Wiring Channels/Cable Tray PVC FRLS Type Standard Slot 45MM X 45MM (Height X Width ) A Type Lock LAN wire Duct ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 45MM X 45MM (Height X Width ) for LAN, telephone and including any damage /cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

S&F PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 25 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

S&F flush mounting factory made Vertical TPN DB, IP-43 Protection -IK 08, with metal double door with 250 Amps rated copper busbar with 2 neutral bar, earth bar and cables ties for cable management fully insulated bus bar with set of wires and door earthing with provision of sapce for TP/FP 160 to 200 amps G Frame MCCB as incomer and SP/TP MCBs as out going 12 way complete all as specified and directed

S&F sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnetic locking system, IP 43, IK 09 protection including necessary provision for inserting the DBs in wall by cutting the brick/stone masonry etc and making good of disturbed surface to match with existing colour of wall complete all as specified and directed

S&F MCCB 4 pole, 415 volts, in the existing panel / location and connection with using aluminum lugs complete all as specified and directed for 160 Amps Adjustable type with breaking capacity 36 KA complete all as specified and directed

S&F MCB TP 25 to 63 amps 10 KA, c-series including connection with suitable size aluminium/copper lugs complete all as specified and directed

M&L for Sub main wiring with two runs of single core FR LSH PVC insulated unsheathed cable 1100 volts grade, 2.5 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including FR LSH PVC insulated unsheathed 2.5Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge. Make of PVC conduit:-Plaza/ Finolex/ Polycab/ Kalinga/ Jindal/ Asian & Make of wire - Havells/Finolex/RR cable Ltd/L&T or other make as specified in Particular specification. Note:- Two runs of main copper cunductor, one run of earth wire and one run of PVC conduit and cutting chasing will be measured as one unit

Supply, laying and testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size 4 core x 16 Sqmm complete all as specified and directed.

Supply, laying and jointing GI pipe 'light grade' 40 mm bore in trenches/under floors or roads/ along poles/ on wall incl clamps for protection of cables including fittings complete all as specified and directed.

M&L for clean and dry sand (un-washed) in trenches including spreading and levelling for cushioning of UG cable complete all specified and directed. Note: Punned thickness shall be measured.

M&L for bricks slightly over burnt (kiln burnt) , modular bricks , best quality, locally available , laid flat, dry, laid in trenches along the length of cable transvarsally with width equal to length of brick for cable protection all as specified and as directed.

M/S Sunshine Construction (BID ID -3142493)

APconstruction (BID ID -3142604)