SPECIAL REPAIR IN MARRIED ORS ACCN MD QTRS NO. P- 89/1 TO P-89/4 AT ADM AREA CPE ITARSI

Amount

Demolition of Cement concrete (unrein forced) in ground floor and pavings not exc 15 cm tickness (below or above ground level) including surface finishes of any type ie tiles, kota stone all as specified and directed

Excavating over areas exceeding 10 Sqm on plain n. exc 1.5m deep and getting out in any type of soil all as specified / directed by Engineer-in-Charge.

M&L 75 mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in Sub base and plinth protection finish the cement concrete surfaces fair and complete all as spciified and directed

M&L for 25mm thick PCC 1:2:4 type BO (using 12.5mm graded stone aggregate) as in sub floor or under layer complete all as specified.

M & L for anti termite treatment for treating the soil under floor at the rate of 5 litres of emulsion per square metre of surface area all as specified and directed.

M & L for anti termite treatment treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area all as specified and directed.

M&L for Moorum and sand filling under floors or pavings laid in layers n exc 15 cm thick spread, levelled and rammed including watering (Sand and moorun will be mixed in ratio 1:1 in filled under floor) complete all as specified and directed

Removing excavated material n exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L plain cement concrete 1:3:6 type C1 using 20 mm graded stone aggregate as in copings ,hold fast,back filling of pressed steel frame and other similar work water troughs and the like including weathering, slightly rounded or chamfered angles and throating etc including form work all as spcefied and directed

Forming jambs etc, to opening including cutting, toothing and properly bonding into old work with cement mortar 1:4,also facing,jointing and pointing to match existing work complete all as specified and directed

Cutting chases pining in brick, walls built in cement mortar or cement lime mortar making good to facings where required and pointing in cement mortor 1:3 to ends or edges of shelves lintels etc and cutting chases for concealed water tubing cutting exc 10 cm but not exc 20 cm girth all as spcefied and directed

Taking down cement or cement lime plaster on brick walls etc including raking out joints, hacking for key scrubing down with water etc all as specified and directed .

M&L for 15 mm thick cement plaster as in cement mortar 1:6 on brick or Concrete surface other than fair finish including dubbing coat if required & finishing with surface even and fair complete all as specified and directed(No extra payement will be paid for dubing coat)

M&L for cutting "V" section to cracks in existig roof or terracing/brick wall including cleaning, and grouting with cement sand slurry 1:3 complete all as specified

M&L for 15 mm thick cement plaster externally in two coats (10mm in CM 1:6 and 5mm in CM 1:4) 5mm thick coat shall be with cement mortor mixed with WPC as per manufacturer instructions with cement ) and finished fair and even complete.(Note :- WPC shall be measured & paid separately) including dubbing coat if required on ground directed by Engr in charge .(No extra payement will be paid for dubing coat)

M&L for 10 mm thick cement plaster in CM 1:3 on celing of concrete surfaces and finished the surface even and smooth complete.

Supply only water proofing compound of approved make

M&L for applying 3 coat of white wash including preparation of new plaster surface on ceiling complete all as specified and directed

M&L for two coat oil bound distemper over a coat of primer on new plastered surface including prepration of surface all as spcefied and directe

M&L for two coat Cement base paint over a coat of primer on new plastered surface including prepration of surface all as spcefied and directed

M&L for two coat oil bound distemper on old surface including complete removal , washing, rubbing down and stopping of existing treatment over a coat of jk Birla wall care putty and making the surface even and smooth and filling the uneven and small holes and making the edges of plaster properly by plaster of paris all as specified and direfcted

M&L for one coat Cement base paint on old plastered surface including complete removal of existing tratment washing down and rubbing and prepration of surface all as spcefied and directed

M&L prepration of old decorated plastered or un plastered surface including cornices etc and applying one coat of white wash on ceiling.

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc 1.5 Sgm each and making good of disturbed surface match the existing surface all as spcefied and directed

All as per item No. 24 here in above but exc 1.5 Sqm but not exc 4 Sqm each

S&F 125x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates,hinges,hold fast(40x3mm) etc. complete size /profile of frame as per IS

S&F 105x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates,hinges,hold fast(40x3mm) etc. complete size /profile of frame as per IS

S&F 30mm thick flush shutters, soild core construction,with block board core and plywood face panels and one face is covered with decorative face veneer with lipping / frame to match complete all as specified and as directed.

S&F 35 mm thick 2nd Class hard wood glazed and skeleton shutters , open rebeted and prepared to receive glass, gauze etc (without sash bars ), edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc , sizes of members of shutters as specified in SSR part-I section 8, clause 8.24 (a) complete all as specified and directed

S&F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as per specification and drawing .

S&F 30mm thick factory made solid PVC moulded door shutter consisting of frame made out of MS tubes for top & bottom rails, MS frames shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on plain side & as gap insert for top and bottom rail. Pannelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement as per specification and drawings.

S&F Framed work as in doors or gates of angle or any type of grill other section with gusset plate rails, braces,etc complete drilled for fixing of steel sheeting or other covering .doors etc prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittngs conforming to Fe-290 (Gde E-165) all as specified and directed.

S&F box type steel windows and ventilator (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on extrernal side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 nos on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes complete all as specified and directed. Note:- The quoted rate a shall also include (i). One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrte surface (ii) 4 nos MS steel lugs made of 20X5 mm Iron flat 200 mm long (iii) PCC block for embedding lugs

S&F 100mm size MS butt hinges medium wt cold rolled.

S&F 150mm long aluminium handles cast type, anodised, complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of etruded section and fixed as specified.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedstaple plate and fixed complete all as specified and directed.

S&F of 300mm long mild steel ordinary rat tail rod pattern springs including roller & roller plate complete all as specified & directed

S&F 2nd class HW small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like including all necessary labours articles n.exc 200 Cucm each.

S&F100mm long hasp and staple,mild steel,wire type, stove enamelled black,including bolt to hinges plate and fixed with screws.

S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified.

S&F of wire netting as chicken wire mesh of galvanised steel wire 0.71mm dia and size of mesh 25mm for cracks fixed with nails etc complete all as specified and directed.

M&L Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples

M&L for prepration of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed of any description over 10cm width or girth.

All as per item No. 44 here in above but on steel surfaces over a coat of red oxide zinc chrome primer.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as spd/directed by Engr-in-Charge.

M&L for non skid coloured ceramic edge cut tiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but n.exceeding 0.18sqm as in floors set & jointed in neat cement slurry & pointed in white or coloured cement to match the tiles over screed bed 15mm thick in cement mortar (1:6) for laying floor finished complete all as spd and directed by Engineer-in-Charge

M&L for non skid coloured ceramic edge cut tiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but n.exceeding 0.18sqm as in floors set & jointed in neat cement slurry & pointed in white or coloured cement to match the tiles over screed bed 15mm thick in cement mortar (1:6) for laying floor finished complete all as spd and directed by Engineer-in-Charge

M&L 20-25 mm thick cuddapa prepolished stone over and including 10 mm thick cement mortar (1:6) bedding laid & jointed with slurry cement mixed with pigment to match the shade of the slab including rubbing and polishing,rounding to edge of stone slab one edge,such as steps,cooking plateorm and similar situtions complete all as specified.(Note-Hole in stone slab for accomodate the gas pipe where required complete.

Dismantling PVC water tanks and removing for capacity exceeding 250 litres & not exceeding 500 litres etc complete.

S&F PVC tank of 500 ltr capacity including S&F 20mm dia pvc float valve assembly complete all as specified and directed.

S&F in repair Gun metal, globe or gate valves for 15 mm dia bore pipe with iron wheel head, screwed both ends for iron pipe and fixed in repair etc complete.

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe all as specified & directed.

S&F 15 mm nipple suitable for HDPE water tanks including necessary driling holes etc fixed complete.

S&F sinks without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plug washers and waste pipe including fixing contilever bracket and connecting union to pipe over all size 495 mmx 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and flynuts, screwed for iron pipes and fixed for 15mm dia

Taking down GI tubing 15mm bore of any description including cleaning for refixing or removal to store.

All as per item No. 57 here in above but 20mm bore.

M&L GI tubing 15mm dia medium grade galvanized, with all fittings fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

All as per item No. 59 here in above but 20 mm bore.

Refixing old GI pipe 15 mm bore & connections in new or old position to walls and ceiling or laid in floor all as specified & directed.

Refixing old GI pipe 20 mm bore & connections in new or old position to walls and ceiling or laid in floor all as specified & directed.

S&F in repair 15mm bore bib tap chromium plated fency type. cast copper alloy with crutch or butterfly handle ,screwed down ,screwed for iron pipe or for brass ferrule complete.

S&F in repair 15mm bore angle valve /stop valve chromium plated fency type.cast copper alloy screwed down high pressure,crutch or butterfly handle, ,screwed both end for pipe or for unions complete.chromium plated with suitable type all as specified and directed.

Supply and fixed in repair stop valves, 15mm dia, cast copper alloy,CP fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions and fixed in pipe all as specified and directed.

S&Fin repair PVC low level 10 litre capacity valveless syphonic action type white flushing cistern with inlet ball valve float and handle including brackets and necessary fittings etc fixed in repairs complete.

S&F in repair viteress china squtting pan "ORISSA PATTERN" size 580x440mm white with integral foot rest and flush pipe complete including provision of concrete bedding 1:2:4 type BO using 12.5mm graded stone aggregate complete all as specified and directed.

S&F in repair WHB white size 550x400mm vitreous china(flat back or angle back type) any size,including cutting for and pinning end of bracket or eracting stand but exclusive of fixing of supply and waste pipe complete.

S&F towel rail 600mm long of PTMT fixed with and including chromium plated brass screw and wooden/plastic cleats.(minimum weight 190grms)

S&F PVC connection 15mm bore size with PTMT nuts of length 450mm long complete all as specified and directed.

S&F 40mm dia PVC pipe low density (LDPE) of pressure 6kg/CM2 fixed to wall or laid in floor as waste pipe complete all as specified and directed.

M& L 15mm size PTMTshower rose with or without joint including fixing to steel pipe or union complete all as specified.shower arm 195mm long complete all as specified and directed.

S&F 75 mm out let PVC floor trap with chromium plated grating including Jointing to waste pipe and fixed in cement concrete B1 (1:2:4 ) using 20 mm graded stone aggregate all as spcefied and directed

Demolition and breaking up or down PVC /AC/CI /Cement rain pipe fixed in any position all as specified and directed

S&F 110mm dia PVC(SWR) pipes single soketed in any length with rubber ring jointed fixed to wall complete all as specified

S&F 75mm dia PVC(SWR) pipes single soketed in any length with rubber ring jointed fixed to wall complete all as specified

S&F PVC (SWR) bends 110 mm dia provided with access door all as specified and directed

S&F PVC (SWR) bends 110 mm dia all as specified and directed

S&F PVC (SWR) bends 75 mm dia all as specified and directed

S&F PVC (SWR) bends 75 mm dia provided with access door all as specified and directed

S&F PVC (SWR) cowl 110 mm dia all as specified and directed

Demolition of reinforced cement concrete in floors ,beams ,chajjas,landing slab in any position or height and similar suspended works.

M&L RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) nominal mix as in slab, chajja, ,landing slab in any position or height and similar suspended works. etc complete all as specified and directed.

Form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work n.exc 200mm thick horizontal or sloping complete all as specified and directed.

M&L 10mm dia and over TMT bar, cut to length, bent to shape required, including cranking, bending , hooking ends and binding with and including mild steel wire(annealed not less than 0.9mm dia) including welding,rivetting etc complete all as specified and directed.

M&L cleaning surface of sunken portion wall/bottom and applying cement slurry @1.2 Kg per Sqm and applying 15 mm thick cement plastred in CM 1:3 finished even and fair using extra cement and applying two coat of acrylic polymer modified cementious slurry as per manufactureas instruction to make the surface leak proof complete all as specified and directed

S & F Curtain rails 20mm dia fix in repair , mild steel, chromium plated with fixing brackets, stops, rollers and finnels etc. and with all necessary fittings complete all as specified and directed.

Demolition brick work or stone / boulder masonry built in cement mortar as in wall etc complete all as directed.

M&L for brick work with sub class 'B' brick in CM (1:4)straight or curved on plan exc 6m mean radius etc complete all as specified and directed by Engr in Charge

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including necessary forms mould mitred /stopped ends etc complete all as specified and directed.

M&L PCC 1:3:6 type C2 using 20mm stone aggregate as in Surface channel or drains including necessary form works , stops ,moulds etc incl demolition of concrete.

S&F for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in chajja roof covering/cladding to wall, fixed with self tapping screws as specified with 'J' or 'L' hook / suitable screw complete all as specified and directed

Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe 290 Gde (E-165)

M&L for heavy duty exterior grade tile texured finish of 300X300X10 mm thick mic/vitrified tile laid over and including 10 mm thick rendering in CM 1:4 as in steps complete all as specified and directed

S&F 18/19mm thick prelaminated particle board interior grade, prelaminated on both side with decorative choice lamination fixed with screws to timber frame work including teak wood beading complete all as specified and directed.

S & F Continuous (piano) hinges mild steel bright finish or electro galvanised width of open flaps 30mm

M&L pressed steel frames for cup board chokhat of size 60x40mm with one or more rebates incl necessary fixing lug, hold fasts etc and one coat of redoxide primer complete.

S&F 40mm thick precast cement concrete louvres and jallies,Type C0 1:3:6 (using 12.5mm stone graded aggregate)(measured solid),(Set in Cement Mortar 1:4) ( including all mouldings , framing etc complete all as specified and directed.

Cutting holes in brick wall, built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortor 1:3 or cement concrete 1:2:4 type B-1 as required area exc half brick but n.exc one brick (depth of embedded portion of hold fasts or lugs measured from the face of the jambs in to wall) all as specified and directed.

M&L for Cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed with grey cement and no pigment set jointed and pointed in neat cement slurry in floors, include 20 mm screed bed CM(1:6) and cut and polished complete all as specified and directed

E/M PORTION Taking down carefully aluminium / copper point wiring with surface/ concealed PVC conduit or wooden batten ( light, fan, socket, bell or power ) including sunk in cast iron / pressed steel terminal boxes except fitting such as switches, ceiling roses, lamp holders, sockets, regulators, call bell, light fitting any sketch etc and making good disturbed surfaces of walls, floors etc complete.

Taking down carefully aluminium sub main wiring with wooden batten / PVC surface conduit complete of any size.

Taking down main switches and distribution board of any size complete.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed rigid non mettalic PVC conduit medium grade (make of conduit-Presto Plast/Pressfit) not less than 19/20 mm ( ISI marked ) with all fitting and fixing accessories including sunk in pressed steel chromium plated terminal boxes,conceled in wall of make & maching the existing surface ) with 2.8 mm thick hylum brand laminated white bakelite sheet cover for mounting switches, sockets, fan regulators etc and 1.5 sq mm multi stranded copper conductor cable as continuous earth wire drawn with wiring and connected to common earth dolly complete (Make of cable-Finolex/Havells/Policab) all as specified and directed for one light point/fan pont controlled by one switch

All as per item No. 105 here in above but one socket outlet 5 Amps controlled by one switch on the same board.

All as per item No. 105 here in above but one socket outlet 5 Amps controlled by one switch on independent board.

All as per item No. 105 here in above but one bell / buzzer controlled by one bell push.

All as per item No. 105 here in above but one light point controlled by two way switch.

All as per item No. 105 here in above but with 2.5 sq mm multi stranded copper conductor cable for one 15 Amps socket outlet controlled by one switch on independent board and 1.5 sq mm PVC insulated multisranded copper conductor cable as continuous earth wire complete.

Material and labour in repairs for sub main wiring with two single core 4 sqmm multi stranded copper conductor, FRLS PVC insulated, unsheathed cable including rigid non metallic PVC conduit medium grade, ISI marked, 20 mm dia for sub main wiring including 4 sqmm FRLS PVC insulated and unsheathed stranded copper conductor as earth wire in conceled in wall of make & maching the existing surface make & maching the existing surface and making good to the disturbed surfaces to match the existing surfaces complete all as specified and directed. Note:- Two runs of 4 sqmm copper conductor cable, one run of 4 sqmm copper conductor and one run of PVC conduit will be measured as one unit.

S & F ceiling rose surface bakelight two to three terminal.

Ding Dong bell AC , 240 volts single pole complete.

S&F Modular switch 1 way 6A, 240 volts 1module complete.

S&F Modular switch 1 way 16A,240 volts 1module complete.

S&F Modular Bell push 6A 1 module complete.

S&F Socket, 6A - 2/3 pin combined 2 module complete.

S&F Socket 6A/16A - 2/3 pin combined 2 module

S&F Fan step regulator, 120W,240 volts 2 module

S&F White cover plate with frame, 1 module

S&F White cover plate with frame but 2 module

S&F White cover plate with frame but 3 module

S&F White cover plate with frame but 4 module

S&F White cover plate with framebut 6 module

S&F White cover plate with frame but 8 module

S&F White cover blanking plate1 module

S&F Metal flush box 1/2 module

S&F Metal flush box 3 module

S&F Metal flush box 4 module

S&F Metal flush box 6 module

S&F Metal flush box 8 module

S&F in repair Decorative Endura Linear Neo LED lighting fixture 20watt ,6000K, (1144mm) with extruded Al. heat sink, environmental friendly, energy efficient ready to use pack.housing with reflector cover channel, with electronic driver, holder, inclding LED tube 20 watt connector block, etc. complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.Make- Havells cat Part No. LHEWEBP7IN1W020 or equivalent make in Wipro/Crompton/Philips/Bajaj

S&F Decorative Endura Linear Neo LED lighting fixture 10watt, 6000K, (581mm) with extruded Al. heat sink, environmental friendly, energy efficient ready to use pack.housing with reflector cover channel, with electronic driver, holder, inclding LED tube 10 watt connector block, etc. complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.Make- Havells cat Part No. LHEWEBP7IN1W010 or equivalent make in Wipro/Crompton/Philips/Bajaj

S& F Decorative wall light fixture made up of Polycarbonate, suitable for LED/CFL complete including one No. LED bulb 9watt fixing the fitting on teak wood board size 4"x6" including all necessary fixing accessories (Make-Havells Catt Pt No-LHDL03160099 or equivalent make in Wipro/Crompton/ Philips/Bajaj

Material and labour in repairs LED light fitting, 1x9 w bulk head luminaries, with lamp holders, LED -9watt etc.complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50 HZ

S&F sheet metal enclosure MCB DB 4 way tripple pole and neutral 415 volts complete.

Supply and fix for sheet metal enclosures for SPN DB's 240 volts, factory made double door flush type, IP-42 protection and all as per IS-8623, made from sheet metal 8 way 200 amps rated bus bar to be fixed with wall all accessories complete all as specified and as directed.

S&F MCB single pole 240 volts 6 to 32 Amps complete.

S & F Switch piano flush type 5 Amps single pole two way complete

S&F MCB double pole 240 volts 16 to 40 Amps complete.

S&F MCB TPN 40 Amp 440 volts Note for item No 136 to 141 : For MCB,s & MCB DB,s, MCB shall be of 10 kA breaking capacity having ,C, characteristics as per IS-8828 with air circulating channels, bicontact terminals, dual position DIN rail clamps with IP-20 degree protection, insulating sliding shutter, MCB for DB,s shall be of same make of DB,s , wiring cable shall be connected to MCB,s with suitable lugs ( copper lugs for copper cable and aluminium lugs for aluminium cable )

Earthing complete with glavanised steel earth plate elactrode 600x600x6.0 mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below ground leves)with top edge of the plate not less 1.5 mtr deep below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nut , bolt, check nut and washer of galvanised iron or of steel, earth lead protected by 15 mm dia GI pipe light grade watering pipe 20 mm dia GI light grade GI wire meshed funnel alternate layer of charcoal and salt PCC chamber , reassed for and including RCC cover including all necessary excavation and earth work, earth wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate no 5 of MES SSR Pt-I 1991 print and as directed.

S&F wall/surface mounting CFL Luminaires (Mirror light) decorative energy efficient luminaire with anti-glare diffuser & decorative end caps suitable for 11W CFL (SU).(Make - Havells cat pt No-LHFOECF1OZ1W011 acrylic diffuser or philips/Crompton Greaves/Wipro/Bajaj including CFL 1x11 Watt complete fittings

Taking down MCB DB /Energy meter after disconnecting supply and kept in safe custody, taking down & remove the old wooden meterbox from site , plastering the existing dusturbed wall surface including colour wash and refixing the Meter/ MCBDB againg with connection complete all as directed

Taking down of old U/G cable 3.5 core 10 sqm to 25 sqm size complete

Excavation in trenches in any type of soil n. exc 1.5 mwide and n. exc 1.5 m in depth and getting out for foundation of pole, laying under ground cables etc and getting out complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm in soil complete all as specified and directed.

Removing excavated soil to a distance n. exc 50m and deposited at a level n.exc 1.5m above the starting point complete all as specified and directed.

Material and labour for river washed and screened dry sand for filling in trenches below and around the cable for cushioning including punning down as specified in relevant clause of SSR Part I. Note: Punned thickness shall only be measured and paid.

Material and labour for well burnt brick sub class 'B' old size bricks laying in trenches perpendicular to axis of the cable all as specified and directed.

Material and labour for GI tubing light grade, 50mm dia with all necessary fittings, laid in trenches, under floor/road crossing, fixed on poles for cable protection fixed with the clamps made out of FI 25 x 3mm duly painted with two coats of aluminium paint over a coat of approved primer etc. complete all as specified and directed.

Supply, lay, connecting and testing cable of size 25 sqmm, 4core, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty), 1100 volts grade with earthed system, stranded aluminium conductor including making input and output connections with using suitable size of thimbles and glands all as specified and directed.

Dashmesh Enterprises

pyarelal galar

TANUJ CONST. CO.