SPECIAL REPAIR TO CERTAIN BUILDINGS IN TECHNICAL AREA AT AIR FORCE STATION AMRITSAR

Amount

B/R Works

Material and labour for cleaning and preparing the roof surface and applying 10 mm thick cement screed in CM1:4 mixed with water proofing compound after applying neat cement slurry @ 3kg /Sqm of surface area & Providing and laying 3 mm thick APP modified prefabricated water proofing membrance, having weight not less than 3.6 kg / Sqm, black finished, reinforced with non-woven polyster matt , including provision of a coat of bitumen primer @ 0.40 ltr/Sqm of density 0.87 to 0.89 kg/ltr at 25 degree C temperature and viscosity 70-160 CPS, over the primer coat the membrane layer shall be laid duly sealed at over laps (100mm side lap and 150 mm end lap ) with flame (by torch application) using butane torch, top surface of the polimeric membrance shall be given 02 coats of aluminium paint over a coat of primer after preparartion surface, complete as per manufacture's instructions, complete all as specified and directed (Note:-The work shall be got executed through the authorised applicator approved by GE

Material and labour for providing and injecting chemical emulsion for post construction Anti-termite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.50 Litres per Sqm of the vertical surface of the sub structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Surfaces excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/disingrated rock complete all as specified and directed.

Material and labour for providing 100 mm thick cement concrete 1:4:8 type D-2 (using 40 mm grade stone aggregate) as in sub floor, sub base of floor complete all as specified and directed.

Material and labour for 50mm thick Plain cement concrete (1:3:6), Type C-1, using 20 mm graded stone aggregate as in plinth protection, finished the surface even and fair, with joints to full depth at corners and @ 3 metres c/c filled with mastic mortar, complete all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises including removal of debries out of defence land complete all as specified and directed.

Material and labour for first quality vitrified ceramic coloured tiles 10 mm thick, (square/rectangular), area of each tile not exceeding 0.36 Sqm, as in floors etc, set and jointed in neat cement slurry @ 3Kg/Sqm and pointed in white cement mixed with pigment or coloured cement to match the shade of tiles, over and including 15 mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 complete all as specified and directed.

Material and labour for first quality vitrified ceramic dark coloured tiles 10 mm thick, (square/rectangular), area of each tile exceeding 0.42 Sqm but not exceeding 1.00 Sqm, as in floors etc, set and jointed in neat cement slurry @ 3Kg/Sqm and pointed in white cement mixed with pigment or coloured cement to match the shade of tiles, over and including 15 mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 complete all as specified and directed.

Material and labour for first quality vitrified ceramic dark coloured tiles 10 mm thick, (square/rectangular), area of each tile exceeding 0.42 Sqm but not exceeding 1.00 Sqm, as on vertical surfaces, set and jointed in neat cement slurry @ 3Kg/Sqm and pointed in white cement mixed with pigment or coloured cement to match the shade of tiles, over and including 15 mm thick bedding layer in CM 1:3 complete all as specified and directed.

Material and labour for first quality vitrified ceramic coloured tiles 10 mm thick, (square/rectangular), area of each tile not exceeding 0.36 Sqm, as on vertical surfaces, set and jointed in neat cement slurry @ 3Kg/Sqm and pointed in white cement mixed with pigment or coloured cement to match the shade of tiles, over and including 15 mm thick bedding layer in CM 1:3 complete all as specified and directed.

Material and labour for First quality, glazed jointed ceramic coloured tiles, 6-7mm thick, of size 300mm x 250mm/450mmx350mm on vertical surface such as in skirting, dados, risers to steps, etc., set and jointed in neat cement slurry @ 3Kg/Sqm, and including pointing in white cement mixed with pigment or coloured cement to match the shade of tiles, over and including 10 mm thick rendering in CM (1:4),complete all as specified and directed.

Material and labour for first quality Non Skid joint free ceramic coloured tiles 7 to 8mm thick, (square/rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc, set and jointed in neat cement slurry @ 3Kg/Sqm and pointed in white cement mixed with pigment or coloured cement to match the shade of tiles, over and including 15mm thick screed bed/bedding layer in CM (1:6), complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/ slabs blankets, any thickness, including cover fillets complete all as specified.

Taking out old serviceable glass partition wall with wooden or metal frame of any description, from old wooden or metal frames, or stone, concrete or brick surrounds, any thickness or size; hacking out old putty or removing beads etc, including making good breakages in taking out and handling, removing to store or stacking for reuse complete all as specified.

Supply and fixing 5 mm thick PVC sheet fillets of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specifications and drawing on page No 162 of SSR part –II complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 5 mm thick solid PVC wall lining consisting of one side wood grain prelaminated colour PVC sheet inclusive of solvant cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

Material and labour for anodised aluminium snap grid frame work for false ceiling complete all as specified.

Material and labour for hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

Material and labour for 12mm thick Perforated particle board/tiles for insulation and accoustic purposes, 60x60 cm in size, fixed in ceiling, flat or sloping , fixed with nails to timber frame work or with staples on snap grid complete all as specified.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern roof covering complete all as specified.

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour as approved having tensile strength of 550 MPA as in roof covering/cladding to wall, fixed with self tapping screws complete as specified complete all as specified.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for and removing rubbish out sie MoD land, complete all as specified and directed.

Material and labour for RCC M-25 (using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

Material and labour for Formwork to rough finished surface of concrete sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, ver hangs, etc. also splays between floors and beams, etc.complete all as specified.

Material and labour for Formwork to Formwork to chullah hoods, chajjas,throughs and similar items including edges complete all as specified and directed.

Material and Labour for TMT steel bars, 10 mm dia and over , cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed.

Demolition of brick masonry work built in cement mortar including all quoins, arches, pillars, staging etc. and removal of rubbish outside MOD land, complete all as specified and directed.

Material and labour for brickwork with using subclass 'B' old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

Material and labour for brickwork in half brick thick wall using subclass 'B' old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:4), complete all as specified and directed.

Taking down cement plaster on brick concrete surfaces etc including raking out joints hacking for key,scrubbing down with water etc from walls and ceiling surfaces of any description & removing debries out side of MD land complete all as specified and directed.

Material and labour for rendering 10mm thick cement plaster in cement mortar (1:3) on concrete surfaces as in ceiling, finished even and smooth without extra cement complete all as specified.

Material and labour for rendering 15mm thick in cement mortar (1:4), using water proofing compound as per manufacturer's instructions, on brick/concrete surfaces of walls, finished even and fair , complete all as specified and directed. Note :- Supply only water proofing compound will be measured and paid for separately.

Material and labour for rendering 20 mm thick (in two layers of 15 mm and 5mm thickness) cement plaster on concrete surfaces in cement mortar (1:4) as in patches on columns, chajjas, canpoy and soffits, using GI chicken wire mesh below the layer of plaster including necessary scafolding arrangement as required at site complete all as specified and directed.

Material and labour for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of new plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

Material and labour for complete removal of existing treatment from ceiling surfaces and applying two coats of white wash including preparation of surface complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of 1st quality oil bound distemper (oil emulsion) over and including a coat of alkali resistant primer, including two coats of acrylic putty to achieve smooth surface complete all as specified and directed.

Material and labour for preparation of surfaces of walls by wire brushes and using sand paper and stopping of surfaces & leveling /edging the disturbed places /edges using necessary filling compound and applying 3mm thick Birla/JK wall care putty to obtain smooth regular/even finish and applying two coats of oil bound distemper complete all as specified and directed

Material and labour for applying two coats of Acrylic weather coat emulsion paint on wall/ceiling/ facing/ramp surface etc in disruptive/camouflaging pattern having percentage of Six colour as 29.04% of RGB value (143, 152, 113), 22.48% of RGB value (112, 139, 86), 14.98% if RGB value (123, 137, 126), 13.80% of RGB value (84, 97, 75),14.15% of RGB value (123, 137, 94) and 5.55% of RGB value (206, 193, 141) as per smaple approved by AGE(I) for bldg of height 7.5 metre, over and including a coat of alkali resistant primer complete all as specified & directed . Note:- Pattern of camouflaging shall be as approved by AGE(I)/Users

Material and labour for applying two coats of Acrylic weather coat emulsion paint on wall/ceiling/ facing/ramp surface etc in disruptive/camouflaging pattern having percentage of Six colour as 29.04% of RGB value (143, 152, 113), 22.48% of RGB value (112, 139, 86), 14.98% if RGB value (123, 137, 126), 13.80% of RGB value (84, 97, 75),14.15% of RGB value (123, 137, 94) and 5.55% of RGB value (206, 193, 141) as per smaple approved by AGE(I) for bldg of height 7.5 metre, including preparation of old surface, complete all as specified & directed . Note:- Pattern of camouflaging shall be as approved by AGE(I)/Users

Supply only integral water proofing compound, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified & directed.

Material and labour for 20mm thick Granite (of any type) work, machine cut, (table rubbed and polished), on cooking platforms, window cills, steps and like, set in neat grey cement slurry @3Kg/Sqm, laid over and including 20 mm thick bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including cutting , grinding & polishing, complete all as specified and directed.

Material and labour for 20mm thick Granite (of any type) work, machine cut, (table rubbed and polished) as in skirting/ dado, set in neat grey cement slurry @3Kg/Sqm, laid over and including 20 mm thick bedding layer in cement mortar (1:3), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including cutting , grinding & polishing, complete all as specified and directed.

Material and labour for 20 mm thick baroda green marble (of any type) work (table rubbed and polished) in steps, jambs, urinal partitions, pillars, window cills,cooking platforms and like laid in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shades complete all as specified .

Roughening of existing floor surface and preparing with wire brushes, sweeping, cleaning and washing down with water to remove all loose dust/dirt etc complete all as specified and dircted.

Material and labour for machine cut kota stone slab flooring with slabs of size not less than 550 mmx550 mm and 20-25 mm thick over and including cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including cutting and mirror polishing and 20 mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 complete all as specified and directed

Material & Labour for machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid and jointed with neat cement slurry, over and including 10mm thick rendering of Cement Mortar (1:4) including pointing in white cement with pigment to match the shade of stone slabs, including taking down cement plaster on walls and racking out joints,hacking for key, scrubing down with water etc, complete all as specified and directed.

Material and labour for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickess M-35 grade with grey cement and pigment complete all as specified and directed.

Material and Labour for Precast Chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick with bullnosed edge, with grey cement and pigment, epoxy coated, set using neat cement slurry @ 3kg/sqm and jointed in neat cement slurry, and pointed in coloured cement or white cement mixed with pigment to match the surface, laid over and including 20mm thick screed bed or bedding layer in CM (1:6), complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame), not exceeding 1.5 Sqm each and removal, including making good the disturbed surface in CM(1:4) and finishing as per existing specifications and removal of debris outside MOD land, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame), exceeding 1.5 sqm but not exceeding 4 sqm each and removal, including making good the disturbed surface in CM(1:4) and finishing as per existing specifications and removal of debris outside MOD land, complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC Sheet & edges will be pointed to match with prelaminated sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing.

Supply and fixing factory made pre-laminated PVC door shutter (conforming to IS-4020) 30mm thick consisting of frame made out of M.S. tubes of 19 gauge thickness & size of stiles, top rail, bottom rails & lock rail all as per shown on drawings in SSR 2010 Pt II, M.S. frame shall have a coat of steel primer of approved make & manufacturer, MS frame covered with 5mm thick heat moulded pre-laminated PVC ‘C’ channel of size 30mm thick, 70mm width out of which 50mm shall be flat & 20mm shall be tapered in 45degree on the either side forming stiles and 5mm thick, 95mm wide pre-laminated PVC sheet out of which 75mm shall be flat and 20mm shall be tapered at 45 degree on the inner side to form top rail & bottom rail and 155mm pre-laminated sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom & lock rail shall be provided on either side of panel. 10mm (5mmx2mm) thick, 20mm wide cross PVC sheet shall be provided as gap inserted to top rail and bottom rail; Paneling of 5mm thick prelam PVC sheet to be fitted with M.S. frame welded/sealed to the stiles & rails with 5mm+2mm thickx15mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive etc. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of "C" channel using PVC solvent adhesive, complete all as specified and directed.

Supply and fixing factory made pressed steel frames for doors with two rebates, of size 105 mm x 60mm, made out of 1.25mm thick sheet, including PCC 1:3:6 type C-0 filling, one shop coat primer and necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

Supply and fixing factory made pressed steel frames for doors with two rebates, of size 125 mm x 60mm, made out of 1.25mm thick sheet, including PCC 1:3:6 type C-0 filling, one shop coat primer and necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

Supply and fixing flush shutters 30mm thick, solid core construction with block board core and 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane pasted on the front face & 2mm Plain colour PVC Sheet on back face, fitted to chowkhats, complete all as specified and directed.

Supply and fixing second class hard wood 35 mm thick plain, glazed and skelton factory made shutters, open rebated and prepared to receive glass, gauge etc (without shash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutter as specified in SSR Part I, Section 8, Clause 8.24(a), kiln seasoned and chemically pressure treated , supplied and fitted to chowkats complete all as specified and and directed. Note:- Glass or Wire cloth in panels will be measured and paid separately.

Supply and fixing Flush cup board shutters 25 mm thick, solid core construction with block board core and 2 mm thick 3D wood grain Moulded PVC Sheet Polyurethane pasted on the front face & 2 mm Plain colour PVC Sheet on back face, complete all as specified and directed.

Supply and fixing stainless steel butt hinges of size 100mm fixed to steel or wooden member complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

Supply and fixing aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

Supply and fixing aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 250 mm and fixed complete all as specified and directed.

Supply and fixing 140mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and directed.

Supply and fixing powder coated any colour as approved Anodised aluminium frame for doors, windows, ventilators (minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified

Supply and fixing powder coated any colour Anodised aluminium door shutters, (minimum thickness of powder coating 5 micron) with aluminium section as directed, including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

Supply and fixing Mortice lock, vertical type, size 100 mm made of brass with two lever complete all as specified

Supply and fixing Aluminium die cast body door closer hydraulically regulated designation No. 3, universal type suitable for door shutter 851 to 1000 mm in width and 61 to 80 Kg in weight complete all as specified and directed.

Supply and fixing double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

Supply and fixing Factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded, including provision of grill as per drawing and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEAF/STD-184-2012 Sheets 1/3, 2/3 & 3/3.

Supply and fixing mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed to steel frames with tinned tacks, or galvanised steel wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed.

Supply and fixing sheet glass 3 mm thick ordinary quality and glazing with oil putty in sqaures n.exc 0.5 sqm in each pane including taking out of old broken glass ( any thickness,size,quality or description ) from wooden or steel frames fixed with putty or with beads, punching or drilling out old glazing pins/ spring clips and providing and fixing new ones complete all as specified and directed

Supply and fixing sheet glass 4 mm thick ordinary quality and glazing with oil putty in sqaures n.exc 0.5 sqm in each pane including taking out of old broken glass ( any thickness,size,quality or description ) from wooden or steel frames fixed with putty or with beads, punching or drilling out old glazing pins/ spring clips and providing and fixing new ones complete all as specified and directed

Supply and fixing new sheet glass 4mm thick ordinary quality and glazing with oil putty in sqaures n.exc 0.5 sqm in each pane, fixed with putty or with beads, punching or drilling out glazing pins/ spring clips complete all as specified and directed

Material and labour, applying two coats of synthetic enamel paint on new steel surfaces over 10cm width or girth, including preparation of steel surface, complete all as specified and directed.

Material and labour applying two coats of synthetic enamel paint over and including a coat of pink primer, on new wooden surfaces over 10cm width or girth, including preparation of wooden surface, complete all as specified and directed.

Supply and fixing in repairs Stainless steel sink with drainage board made of 1.00 mm thick sheet for kitchen with plugs washers & wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm with bowl size 410mmx330mmx160mm, with and including PVC waste pipe and CP waste coupling 32 mm, complete all as specified directed.

Supply and fixing Vitreous china wash hand basin, white, flat back, size 450mm x 300mm, including brackets and cutting for and pinning in ends of brackets, complete including CP brass waste coupling, PVC waste pipe, brackets & including taking down old and removal of old from site, complete all as specified.

Supply and fixing white colour Vitreous china counter oval wash hand basin, size 550mm x 450mm, including CP brass waste coupling, PVC waste pipe & inluding taking down old and removal of old from site, complete all as specified and directed by Engr-in-charge.

Supply and fixing vitreous china wash down water closet squatt pan, Indian type (Orissa pattern), of size 580mmx440mm, white with integral foot rests (excluding flushing cistern) pipe but including CI ‘P’/’S’ trap), set in & jointed with appripriate adhesive/mortar including embedding in concrete including 32mm bore PVC flush pipe & jointing with adhesive, and taking down old and removal of debris outside MOD land, complete all as specified and directed.

Supply and fixing Vitreous china one piece cascade water closet of size 580mm X 440mm, white with integral foots rests (including flushing cistern) pipe, including CI 'P/S trap, set in & jointed with appropriate adhesive/mortar, including embedding in corcrete and taking down old WC and removal of debris outside MoD land, complete all as specified and directed.

Supply and fixing 10 litre capacity virgin polypropylene (PVC) low level flushing cistern, ISI marked, white or coloured, valve less symphonic action type, with inlet, ball valve, float and handle, complete including PVC bend/ flush pipe, brackets and making all connections, fixed as in repairs and removal of old from site to store for reuse or credit, complete all as specified and directed.

Supply and fixing in repairs 32mm dia waste coupling of PTMT (half or full threaded) having minimum weight 45gnms complete all as specified and directed.

Supply and fixing pillar taps cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

Supply and fixing PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

Taking up or down existing steel water tubing and connections, 15mm bore for re-fixing or removing from site to store for reuse or credit, including taking down standard fittings, complete all as specified and directed.

Taking up or down existing steel water tubing and connections, 20mm bore for re-fixing or removing from site to store for reuse or credit, including taking down standard fittings, complete all as specified and directed.

Supply and fixing galvanized steel water tubes, 15mm bore, medium grade, with all standard fittings such as bends, elbows, tees etc, concealed/on surface, fixed to walls and ceiling or laid in floors, complete all as specified and directed. Note : Cost for cutting chases including making good as required shall be deemed to be included in qouted rate of this item.

Supply and fixing galvanized steel water tubes, 20mm bore, medium grade, with all standard fittings such as bends, elbows, tees etc, concealed/on surface, fixed to walls and ceiling or laid in floors, complete all as specified and directed. Note : Cost for cutting chases including making good as required shall be deemed to be included in qouted rate of this item.

Supply and fixing in repair 15mm dia bib tap, fancy type, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as per specified and directed by E-in-charge

Supply and fixing in repair 15mm dia Angle stop valve of PTMT having minimum weight 90 grams, any colour, high pressure, screwed for iron pipe and fixed,complete all as per specified and directed.

Supply and fixing 600 mm long PTMT towel rail having minimum weight190 grams fixed with and including CP brass screwes and wooden/plastic cleats including required fittings complete all as per specified

Supply and fixing plate rack made of stainless steel sheet 1mm thick having over all size 600mm x750mm x 250 mm complete all as per specified and directed by E-in-charge

Supply and fixing in repair 15 mm stop valves, cast copper alloy, screwed down, high pressure, fancy type chromium plated, screwed, both ends for iron pipe or for unions and fixed all as per specified and directed by E-in-charge.

Supply and fixing in repair 20 mm stop valves, cast copper alloy, screwed down, high pressure, fancy type chromium plated, screwed, both ends for iron pipe or for unions and fixed all as per specified and directed by E-in-charge.

Supply and fixing brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified & directed.

Taking down PVC(SWR) pipe 110 mm dia bore in any position complete all as directed.

Taking down PVC(SWR) pipe 75 mm dia bore in any position complete all as directed.

Material and Labour for 110mm bore PVC (SWR) pipe (Type 'B'), single socketed, in any length with rubber ring joints, laid in trenches, complete all as specified.

Supply and fixing PVC (SWR) bend any radius for 110 mm bore pipe incl jointing material complete all as specified and directed.

Supply and fixing PVC (SWR) branch piece, single (single Y) equal or unequal for 110mm dia bore incl jointing material complete all as specified and directed.

Supply and fixing PVC (SWR) branch piece, double (double Y) equal or unequal for 110mm dia bore incl jointing material complete all as specified and directed.

Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal for 110mm dia bore as specified and directed.

Supply and fixing PVC 75mm dia (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed..

Supply and fixing PVC (SWR) bend any radius for 75 mm bore pipe incl jointing material complete all as specified and directed.

Supply and fixing PVC (SWR) branch piece, single (single Y) equal or unequal for 75mm dia bore incl jointing material complete all as specified and directed.

Supply and fixing PVC (SWR) branch piece, double (double Y) equal or unequal for 75mm dia bore incl jointing material complete all as specified and directed.

Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal for 75mm dia bore as specified and directed.

Supply and fixing in repair 75 mm dia PVC (SWR ) floor trap/ nahani trap,with grating plain with grating including jointing with solvent cement complete all as specified and directed

Supply and fixing in repair 75 mm dia PVC (SWR ) multi floor trap/ nahani trap with grating, plain with grating including jointing with solvent cement complete all as specified and directed

Material and labour for PVC gully traps square of size 125mm x 110mm including for setting and jointing to drain with CM 1:1 etc complete all as specified & directed.

Dismantling water tanks of capacity exc. 250 Litres but not exceeding 500 Litres and removing to store yard complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing/hoisting, rotational moulded polyethylene (HDPE) water storage tanks (cylindrical vertical with closed top), 500 litres capacity ‘double layered’, hoisted and fixed in position including inlet, outlet and drain pipe with plug, complete all as specified and directed.

Supply and fixing aluminium anodised curtain rod of 20mm dia complete complete all as specified and directed.

Supply and fixing brackets for curtain rod of 20mm dia fixed to wall complete complete all as specified and directed.

Material and labour for providing precast cement concrete in kerb stone for footh path and paving etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match complete all as specified and directed.

Supply and fixing rolled mild steel in joist, channel, angle or tee sections, fixed independently without connecting plates etc conforming to Fe 410-W (Gde E-250) complete all as specified and directed.

Supply and fixing 1 mm thick mild steel plain black sheet in wall cladding, steel gate and similar work, cut to size, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted and welded seams as required including bending or turning up, mitred angles etc. as required complete all as specified and directed.

Material and labour for 25 mm thick sand filling under floor or in foundations incl watering and consolidation complete all as specified.

Material and labour for providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh complete all as specified and directed.

Supply and fixing aluminium composite panel (ACP) false ceiling in colour of approved shade, made out of 4mm thick (weight not less than 5.48 Kg/Sqm) ACP material consisting of FR grade mineral core sandwiched between two aluminium sheets (each 0.50 mm thick). The ACP panel sheet shall be coated with Kynar 500 based PVDF/Lumiflon based flour polymer resin coating of approved colour and shade on face 1 and polymer (service) coating on face 2 as specified including stainless steel screws, nuts, bolts, washers, cleats, weather silicon sealant etc,capable to withstand stresses without sagging, connecting with GI frame work (size of grid 605mmx605mm) for seamless ceiling, comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre, intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc. 1.5 m length) of 0.55 mm thickness having knurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre with hanging 6mm dia GI (upto 1200mm length), adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40mmx3mm size 60mm long, complete all as specified and directed. Note:- Cost for ACP false ceiling connecting with frame and hanging with rod shall be deemed to be included in quoted rate.

Material and labour for washed stone grit plaster on exterior walls in two layers, under layer 12mm thick cement plaster in cement mortar 1:4 (1 cement: 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster in cement mortar 1:1/2:2 (1 cement : 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings complete all as specified.

Supply and fixing factory made UPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two Nos glazed & one No wire mesh panels) upto 1.50m height made of (big series) frame 116mm x 45mm & sash bar 46mm x 62 mm both having wall thickness of 2.3+ 0.2mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of UPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 + 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), appropriate dimension of UPVC extruded glazing beads and UPVC extruded interlocks, EPDM gasket, wool pile, Zinc alloy (white powder coated) touch locks with hook, Zine alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100mm x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engr-in-Charge. (Glass or wiremesh shall be measured and paid separately) Note: For UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing stainless steel members of grade 304 of section and profile as directed as per requirement at site, including all necessary cutting, welding, polishing etc. Complete all as specified and directed.

Supply and fixing vertical window blinds 100mm louver width, quality of approved make fabric made of 100% polyester woven fabric thickness 0.40 mm with acrylic coating resistance to cracking & fraying and treated for dust replellency, UV Proof, virtually maintenance free having plastic bottom chain, thickness of chain 0.5mm and diameter 3mm, plastic with metal bottom weight-116.20mm x 48.30mm and suitable coating on exterior, including all fixtures and fittings complete in all respect as per design/colour/shade including requisite installation brackets etc as required for installation at site with anchoring arrangements compete all as specified and directed by Engr-in-Charge.

E/M Works

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including GI earth wire on batten or in PVC conduit or in MS Conduit including fixtures and fittings such as switches, ceiling roses, pendants, fan regulators, sockets etc, removing materials to store for keeping in safe custody for reuse or for credit (credit for above items shall be made as per conditions separately) and making good disturbed surface of walls, floors, etc., complete all as specified and directed.

Material and labour for point wiring with single core multi stranded copper conductor 1.5 Sqmm (nominal area) PVC insulated unsheathed FRLS colour code cable of 1100volts grade drawn through and including non metalic rigid PVC conduit medium duty of suitable size with all standard fittings such as Tee junction, bends etc, concealed in wall/fixed on ceiling including M.S. sunken boxes of suitable size made of 1.6mm thick MS sheet duly painted with anticorrosive paint, for housing switches, fan regulators etc. including 1.5Sqmm (nominal area) multi stranded copper conductor PVC insulated unsheathed FRLS colour code cable of 1100volts grade for earth continuity, as for one light/exhaust fan/bell point or fan point (through regulator), controlled by one switch, complete all as specified and directed. Note(s) : (i) Rate quoted shall be deemed to include cutting chases for concealing conduit and making good in cement mortar (1:4) or PCC (1:2:4) as required. (ii). Switches and fan regulator etc., shall be measured and paid separately.

All as per item No. 131 hereinbefore but wiring for one 3 pin 6 Ampere socket outlet point on the same board, controlled by other switch complete all as specified and directed.

All as per item No. 131 hereinbefore but wiring for one 3 pin socket outlet 6 amps independent board.

Material and labour, point wiring complete with two single core multi stranded Copper conductor of size 2.5 Sqmm (nominal area) FRLS PVC insulated unsheathed 1100 volt grade colour code cable, drawn in and including non metalic rigid PVC conduit medium grade of suitable size including standard fittings such as Tee junction, bends etc, conduit concealed in wall & fixed on ceiling including M.S. sunken boxes of suitable size made out of 1.6 mm thick sheet duly painted with anticorrosive paint for housing switches, sockets etc, including one 1.5Sqmm size (nominal area) multi stranded copper conductor FRLS PVC insulated unsheathed colour code cable for earth continuity, for one multi purpose socket outlet 6 pin, 15Amps & 5Amps on independent board, complete all as specified and directed. Note(s) : (i) Rate quoted shall be deemed to include cutting chases for concealing conduit and making good in cement mortar (1:4) or PCC (1:2:4) as required. (ii) Switches etc. shall be measured and paid separately. Circuit wiring from distribution board to switch board shall be deemed included in the quoted rate of point wiring.

Supply and fixing in replacement of old UNSV tube light fittings with new LED tube light fitting with aluminium housing 1x22 watts with PVC insulated flexible copper cable from ceiling rose to tube light fitting complete all as per specified and directed.

Supply and fixing in replacement of old UNSV bulk head fittings with new light fitting 1 x 10/12 watt bulk head luminaires including connecting up with twin core twisted flexible copper conductor cable of suitable size for 230 Volts, 50HZ complete all as specified and as directed.

Supply and fixing in replacement of old UNSV SMD LED panel with new SMD LED panel recess/surface suspended mounting 36-42 watt 2' x 2' LED ceiling light with extruded aluminium housing and milky diffuser including connecting up with twin core twisted flexible copper conductor cable of suitable size for 230 Volts, 50HZ complete all as specified and directed.

Supply and fixing in replacement of old UNSV SMD LED panel with new SMD LED panel recess/surface suspended mounting 21-24 watt round shape LED ceiling light with white powder coated aluminium housing and milky diffuser including connecting up with twin core twisted flexible copper conductor cable of suitable size for 230 Volts, 50HZ complete all as specified and directed.

Supply and fixing in replacement of old UNSV SMD LED panel with new SMD LED panel recess/surface suspended mounting 6/7 watt round shape LED ceiling light with extruded aluminium housing and milky diffuser including connecting up with twin core twisted flexible copper conductor cable of suitable size for 230 Volts, 50HZ complete all as specified and directed.

Supply and fixing in replacement LED Tube Light, surface mounting, 10 watt, 2 feet long, suitable for mirror light with milky diffuser, including connecting up with twin core twisted flexible copper conductor cable of suitable size for 230 Volts, 50HZ complete all as specified and directed.

Supply and fixing in replacement and testing ceiling fan 1200mm sweep, metallic body, metallic blades, copper wound heavy duty with minimum BEE 3 star rating, 230 volts, single phase, high speed, heavy duty, operating on single phase AC supply, including provision of PVC insulated flexible copper wire 1.5 Sqmm three core from ceiling rose to fan for giving connection, complete all as specified and directed. Make - Havells,Crompton Greaves, Bajaj, Standard India or equivalent make as per Appx 'B' . Note:- Old retrieved ceiling fan shall be property of Govt and shall be deposited in MES store.

Supply and fixing in replacement wall mounted fan 450 mm sweep heavy duty 3 star rating, metalic body & blade suitable for 230V single phase AC supply including PVC insulated flexible three core 1.5 sqmm copper cable from ceiling rose to fan complete all as specified and as directed. Make - Havells,Crompton Greaves, Bajaj, Standard India or equivalent make as per Appx 'B' Note:- Old retrieved fan shall be property of Govt and shall be deposited in MES store.

Supply and fixing in replacement single phase propeller type ventilating ( Exhaust fan) AC 230 volts 300 mm sweep, Double Ball Bearing, Heavy duty motor, durable body complete with louvers and shutters with all fixing arrangement fixed to wall with suitable size opening including copper wire flexible three core 1.5 sqmm PVC insulated from ceiling rose to exhaust fan complete all as specified and as directed. Make:- Havells, Crompton Greaves, Bajaj, Osram, Standard Indiaor equivalent make as per Appx 'B' Note:- Old retrieved Exhaust fan shall be property of Govt and shall be deposited in MES store.

Supply and fixing in replacement of old UNSV lamp holder with new lamp holder PVC / polycorbonate type insulated body with back plate suitable for batten fitting / angle fitting complete all as specified and directed.

Supply and fixing in replacement LED Building light /security light luminaries fitting 1X40 watt LED including fixing bracket made out of GI pipe light grade 35 mm dia 1.20 m long bent to shape with suitable size mild steel clamps of size 50mm X 6mm with nut, bolt & washers as required at site for fixing of street light on LT poles / wall including making connection with PVC insulated 3 single core of 1.5 sqmm size multistranded copper conductor cable complete all as specified and directed.

Supply and fixing in replacement ceiling rose, surface bakelite, 65 X 50 mm, 3 terminals complete all as specified and directed.

Supply and fixing in replacement Modular switch paino flush type one way 6 Amp, 230 volts complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement Modular switch paino flush type one way 16 Amp, 230 volts complete all as specified and directed by Engr-in-Charge

Supply and fixing in replacement Modular socket 6 Amp 2/3 pin combined 2 module complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement Modular socket 6 /16 Amp 2/3 pin combined 2 module complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of stepped type modular fan regulator 2 module flush type on the existing phenolic laminated sheet etc. as reqd heavy duty 230 volts complete all as specified and directed.

Supply and fixing in replacement white cover plate with frame for 2 module, complete all as specified and directed.

Supply and fixing in replacement white cover plate with frame for 3 module, complete all as specified and directed.

Supply and fixing in replacement white cover plate with frame for 4 module, complete all as specified and directed.

Supply and fixing in replacement white cover plate with frame for 6 module, complete all as specified and directed.

Supply and fixing in replacement MCBs Distribution board sheet metal enclosures, SPN 240 Volts, 08 ways with 200 amps rated bus bar, double door for MCBs, with IP 43 protection, including blanking plate as required, including making good the disturbed surfaces to match with the existing, complete all as specified and directed.

Supply and fixing in replacement MCB DP, 240 Volts, AC, 'B' curve, 10 KA, 40 Amps, complete all as specified and as directed.

Supply and fixing in replacement MCB single pole, 240 Volts, AC, B curve, 10 KA, 6 to 32 Amps, complete all as specified and as directed.

Material and labour for Sub Main Wiring (in replacement) with two single core 6 Sqmm (nominal area) multi stranded copper conductor FRLS PVC insulated and unsheathed colour code cables, drawn in and including non-metalic rigid PVC conduit, heavy duty of 25 mm dia, including standard fittings such as Tees, junction, bands etc., conduit concealed in wall & fixed on ceiling with suitable clamps with and including one run of continuous multi stranded copper conductor 6 Sqmm (nominal area) FRLS PVC insulated and unsheathed colour code cable for earth continuity, 1100 volts grade , complete all as specified and directed. Note(s): (i) Two runs of 6 Sqmm main cable + one run of 6 Sqmm cable for earth continuity and PVC conduit shall be measured as one unit/one Running Metre. (ii) Rate quoted shall be deemed to include cutting chases for concealing conduit and making good in cement mortar (1:4) or PCC (1:2:4) as required.

Material and labour for Sub Main Wiring (in replacement) with two single core 4 Sqmm (nominal area) multi stranded copper conductor FRLS PVC insulated and unsheathed colour code cables, drawn in and including non-metalic rigid PVC conduit, heavy duty of 25 mm dia, including standard fittings such as Tees, junction, bands etc., conduit concealed in wall & fixed on ceiling with suitable clamps with and including one run of continuous multi stranded copper conductor 4 Sqmm (nominal area) FRLS PVC insulated and unsheathed colour code cable for earth continuity, 1100 volts grade , complete all as specified and directed. Note(s): (i) Two runs of 4 Sqmm main cable + one run of 4 Sqmm cable for earth continuity and PVC conduit shall be measured as one unit/one Running Metre. (ii) Rate quoted shall be deemed to include cutting chases for concealing conduit and making good in cement mortar (1:4) or PCC (1:2:4) as required.

Supply and fixing in replacement vertical type sheet steel enclosure distribution boards, double door, factory made, 3 phase 415 volts ,4 ways, with 200 amps rating copper bus bar of suitable size and PVC insulated copper jumpers from the MCCB to the out going circuits (one incoming MCCB and 12 outgoing MCBs circuits) comprising of 3 phase 4 wire of suitable rating including provision of MCCB 160 amps, 25 KA, TP, 415 volts, 50 Hz = 01 No and MCBs 6-32 Amps =12 Nos, complete all as specified and directed.

Supply and fixing in replacement sheet metal enclosure, SPN, with a two pin socket and earth plug, with one MCB single pole, 240 Volts, 20 Amps, complete all as specified and directed.

Supply , laying jointing and commissioning in replacement LT under gound cables XLPE insulated screened PVC bedded galvanized steel strip armoured electric powder cable (heavy duty) with alumininum conductor cross sectional area 150 Sqmm 3.5 core LT, 1100 volts grade , laid in trenches , along poles or passing with through pipe or laid under floor or through/ on walls etc, including taking out old UNSV cable with protection bricks and removal including connection of cable point as required complete all as specified and directed. Note:- Excavation and earth work , sand cushioning, brick protection and GI pipes for protection shall be measured and paid for separtely.

Supply , laying, jointing and commissioning, LT under gound cables XLPE insulated screened PVC bedded galvanized steel strip armoured electric powder cable (heavy duty) with alumininum conductor cross sectional area 70 Sqmm 3.5 core LT, 1100 volts grade , laid in trenches , along poles or passing with through pipe or laid under floor or through/ on walls etc, including connection of cable joint to connect the cable as required/directed and taking out old UNSV cable with protection bricks and removal, complete all as specified and directed Note:- Excavation and earth work , sand cushioning, brick protection and GI pipes for protection shall be measured and paid for separtely.

Supply , laying jointing and commissioning in replacement LT under gound cables XLPE insulated screened PVC bedded galvanized steel strip armoured electric powder cable (heavy duty) with alumininum conductor cross sectional area 35 Sqmm 3.5 core LT, 1100 volts grade , laid in trenches , along poles or passing with through pipe or laid under floor or through/ on walls etc, including connection of cable joints as reqd in site for laying the cable and taking out old UNSV cable with protection bricks and removal, complete all as specified and directed Note:- Excavation and earth work , sand cushioning, brick protection and GI pipes for protection shall be measured and paid for separtely.

Supply , laying, jointing and commissioning, LT under gound cables XLPE insulated screened PVC bedded galvanized steel strip armoured electric powder cable (heavy duty) with alumininum conductor cross sectional area 16 Sqmm 2 core LT, 1100 volts grade , laid in trenches , along poles or passing with through pipe or laid under floor or through/ on walls etc, including taking out old cable with protection bricks and removal, complete all as specified and directed Note:- Excavation and earth work , sand cushioning, brick protection and GI pipes for protection shall be measured and paid for separtely.

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep for laying of cables and foundation of poles etc. and getting out complete all as spceified and directed.

Returning, filling in trenches (soil) including spreading leveling and well ramming in layers not exc 25 cm thick complete all as specified and directed.

Removal of surplus excavated soil to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

Material and labour for sand cushioning with a layer of dry river sand 80mm thick before laying of cable and 150 mm thick (punned down to 100 mm thick) after laying of cables, in trenches/ducts complete all as specified and directed Note: Punned down thickness (overall 18cm), shall be considered for measurement and payment.

Material and labour for locally available , sub class 'B' bricks (old size) laid flat and dry in trenches over the cable for protection prependicular to the direction of cable adjacent to each other complete all as specified and directed.

Material and labour in replacement GI pipe light grade 80 mm bore for cable protection fixed to pole or under road/ pavement, complete including MS clamps, nuts, bolts etc as required complete all as specified and directed.

Material and labour in replacement GI pipe light grade 40 mm bore for cable protection fixed to pole or under road/ pavement, complete including MS clamps, nuts, bolts etc as required complete all as specified and directed.

Material and labour for taking down outdoor / indoor complete unit of split type and window type AC of any capacity from existing position and refixing the same after necessary repair/servicing at same location including civil work, copper pipe, PVC pipe and other material required at site, complete with making good disturbed surfaces so as to match with existing surface and necessary arrangement for fixing of AC, complete all as specified and directed by Engineer-in-Charge .

Supply and filling at site, Refrigeration gas R-134/R-22/F-22 (Mefron/Refron) in returnable cylinder complete all as specified and directed by Engineer-in-Charge .

Material and labour for providing earthing of advance chemical earthing system of Copper pipe Chemrode 3 mtrs long 50mm dia filled with highly conducting metallic compounds with the permanent sealings at both the ends. Top of the earth electrode shall be compressed to form an extended lead with 2 holes for connecting the strip/wire to the load. To ensure the moisture content and electrical conductivity, each earthing pit shall be provided with minimum 02 bags of 20 kgs chemical compound. An arrangement for connection of copper strip (25x3mm) to rod to be made with given Terminal point with SS Nut Bolts, provision of polymer chamber with cover, including necessary excavation in any type of soil, returning, filling in, removal of surplus soil complete all as specified and as directed Make : JK CHEM RODE / LPI /Alltec/Akaltech

Note(s) :- The qouted rates shall deem to include the following:- (i) Pit cover chamber of polymer chamber with cover, including necessary excavation in any type of soil. (ii) Copper strip with necessary brazing and GI protection pipe upto a length of 7.5m, Length beyond 7.5m required at site shall be measured and paid separately (iii) Earth resistance shall be less than 1Ohm. In case the test results are not found below 1Ohm, complete earthing will be redone without any extra cost to Govt. (iv) For effective visibility identification and traceability of earth pit (EP) with corresponding earth of eqpt and bldg, markers in metal (Mild Steel) shall be provided. Earth test of earth pit shall be provided with a colour code. The direction regarding the size, shape and colour of the Mild steel identification board etc., shall be given by the Engineer-in-Charge. (v) The work is to be carried out in replacement of existing earthing. The quoted rate shall be deemed to include for taking out, dismantling & disposal of metalic materials/components of old earthing and credit for retrieved metallic materials shall be deducted as per 'Schedule of Credit'. (vi) All joints of strip are to be brazed on both sides (over lapping) except test point.

Earthing complete with galvanized steel earth plate electrods of size 60cmx60cmx6mm thick burried directly in ground vertically(earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanized iron or steel earth wire 4 mm dia by means of bolts nuts check nuts and GI washers of Galvanised iron protected by steel pipe 15mm (light grade) all as shown in elecrrical plate No.5 of SSR Part-I and connecting to earthing test point (earth test point to be provided at 5 mtr distance from earth pit) and testing on completion including necessary excavation and earth work. The rate also include charcoal dust and salt in alternate layers, 25 mm dia light grade GI pipe,funnel,wire mesh,Cement Concrete 1:3:6 type C-1 for pit and RCC pit cover. The cost of the watering pipe,bends,elbows etc shall be included in the quoted rate. Note : RCC pit cover shall be precast of RCC 1:2:4 type B-1 80mm thick reinforced with XPM weighing not less than 4 Kg/Sqm including dismantling of old UNSV pit cover/earthing complete all as specified and directed.

Note: The Total amount shall subject to adjustment of credit of Rs. 111461.00 for old Materials as per Schedule of Credit.

PAUL CONSTRUCTION CO.

M/s AKG Engineers & Contractors

Sachdeva Builders