SPL REPAIR TO BLDG NO HA 172 NH 43 NH 44 AND LA 09 AT BAGRAKOTE MIL STN UNDER GE SEVOKER ROAD

Amount

Taking down chowkats with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each complete all as specified.

Taking down chowkats with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.00 Sqm each. complete all as specified

Dismantling of wrought iron or mild steel work of any description not other wise provided for complete all as specified.

Dismantling plain or corrugated steel sheeting any gauge or thickness as in roof covering complete all as specified.

Dismantling timber scantling 40 Sqcm and over in section any position as in framed works complete all as specified.

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified.

Dismantling wall & ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified.

Demolition of cement concrete (unreinforced ) in ground floors and pavings n.exc 15cm thickness (below or above GL) complete all as specified.

M&L for Brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6. complete all as specified.

M&L for Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4. complete all as specified.

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in block for hold fast, filling in frames, benching & copings or similar work and finished the surface with existing and including form work. complete all as specified.

S&F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlines to steel trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165. complete all as specified.

S&F pressed steel frames (Size-165X60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified .

S&F pressed steel frames (Size-105X60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified .

S&F factory made 2nd class hard wood rail and style 35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS:1003 (part I), kiln seasoned and chemically pressure treated.complete all as specified.

M&L for 35mm thick Glazed and skeleton shutter open rebated and prepare to receive glass, gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing gauge etc size of members of shutters as specified in SSR Pt-I Section 8 and clause 8.24(a) of second class hard wood all as specified.

S&F mild steel tower bolts stove enamelled black with bright bolt 200 mm long. complete all as specified.

S&F 300 mm long mild steel sliding door bolts plate type stove enamelled black with bright bolts not less than 12mm dia with including a minimum of 6 bolts, nuts four on bolts plate & two on staple plate . complete all as specified.

S&F mild steel pressed handle oval type stove enamelled black 150 mm long. complete all as specified.

S&F 2nd class hard wood small fittings such as bracket of any type latch hinges blocked shapped door & window stopper and cleat including all necessary labour articles not exceeding 200 cu cm each. complete all as specified.

S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS sqare tube, complete all as specified.

S&F factory made, solid panel PVC door shutter, 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frames shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified.

S&F 150mm size aluminium, anodised barrel tower bolt of extruded section. complete all as specified.

S&F 100 mm size of stainless steel butt hinges, medium weight, cold rolled complete all as specified.

S&F 100mm size extruded aluminium alloy handles, fabricated type complete all as specified.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete with glazing bars, dovetailed or welded complete all as specified.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete without glazing bars, dovetailed or welded complete all as specified.

S&F steel ventilators with top hung shutters including hinges, steel peg stay, complete all as specified.

S&F 3mm thick glass sheet ordinary quality & glazing with oil putty in square not exc 0.50 Sqm in each pane complete all as specified.

S&F galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified.

M&L rendering 15mm thick in CM 1: 6 on fair faces of brick/concrete surfaces finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 including mixing WPC as per manufacturers instruction, finished even and smooth without using extra cement complete all as specified. (WPC shall be measured seperately).

Supply only integral water proofing compound.

S&F Rolled Mild Steel in Roof trusses (framed), trussed, purlins, crane, gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, etc( Fe 410-W Gde-E-250) (Including preparation of surface and one shop coat of zinc chromate primer paint) at contractors workshop before fabrication complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self drilling and self tapping screws, neoprene and limpet washers complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self drilling and self tapping screws, neoprene and limpet washers complete all as specified and directed.

S&F mild steel screw bolt, 5 to 10mm dia machine made with hexagonal head at one end and screwed the other or scrwed both ends screwed end to be fitted with washer and one hexagonal or square nut exceeding 5cm and not exceeding 10cm long complete all as specified.

S&F 605X605mm anodised aluminium snap grid frame work for false ceiling and fixed to steel or wooden member all as specified and as directed.

S&F hangers 6mm dia. G.I. (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long complete all as specified.

M&L 4mm thick non asbestos fibre cement building boards fixed or laid/inserted to aluminium frame work in ceiling complete all as specified and as directed.

Preparing of new non AC board surfaces and applying three coats of white wash on ceiling complete all as specified and as directed.

M&L 25mm thcik PCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in levelling coarse complete all as specified and as directed.

M&L for rendering in CM (1:4), 10mm thick on fair faces of brick work or concrete surfaces for fixing of wall tiles/skirting complete all as specified.

M&L for screed bed or bedding layer of cement mortar 1:6, 15mm thick for laying floor finishes complete all as specified.

M&L for non-skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

All as per item No. 47 above but in vertical surfaces such as skirting, dados and riser to steps etc. complete all as specified.

M&L for glazed ceramic tiles in vertical surfaces 300 x 200 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L for non-skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L for granite 20mm thick (of any type) work (table rubbed and polished) in cooking platform and like in cement mortar (1:4) includning pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

M&L 75mm thick cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection & paving finished even & smooth without using extra cement complete all as specified.

M&L for preparation of new untreated wood and wood base material of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for preparation of new steel surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified.

M&L for preparing new steel and iron surfaces of any description n.exc 10 cm in width or girth and apply two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

M&L RCC 1:2:4 , type B1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span and lintel band, roof band and other similar items including form work all as specified.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed, not less than 0.9mm dia or securing with clips complete all as specified.

All as per item No. 57 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders all as specified and as directed.

S&F mild steel work (miscellaneous) as in wind ties for roof, flat iron fillets (for securing wire mesh etc) including drilling holes for securing bolts and fixed with bolts and nuts etc and similar work conforming to Fe-290.Gde-E-165, complete all as specified and as directed.

M&L for complete removal of existing treatment on wall surfaces and applying two coats of Cement Based Paint over a coat of alkaline resistant primer, complete all as specified and as directed

Preparation of new plaster surfaces and applying two coats of distemper oil emulsion over a coat of chalk whiting on wall. complete all as specified.

Preparation of old treated surfaces and applying one coat of distemper oil emulsion on wall. complete all as specified.

M&L for preparation of newly plastered wall surfaces and applying two coats of Cement Based Paint over a coat of alkaline resistant primer, complete all as specified and as directed

S&F in repairs vitreous china squatting pan orissa pattern size 580x440mm white with integral foot rest and accessories. complete all as specified.

S&F PVC valveless, syphonic action type flushing cistern low level, 10 litre capacity with it’s complete accessories, fixed complete including connection to water pipe and PVC 32 mm dia flush pipe etc. complete all as specified.

S&F PVC connection 15mm dia with PTMT nuts of length 450mm complete all as directed.

S&F bib tap standard of PTMT, any colour, screwed for iron pipe of size 15 mm and fixed all as specified and directed. (minimum weight 90gm).

Taking up or down steel water tubing 15mm dia and connections, including cleaning for refixing or removal to store. complete all as specified.

Taking up or down steel water tubing 20mm dia and connections, including cleaning for refixing or removal to store complete all as specified.

Taking up or down steel water tubing 25 mm dia and connections, including cleaning for refixing or removal to store complete all as specified.

S&F 15mm dia steel water tubing, galvanised, medium grade with all fittings and fixed to wall and ceiling or laid in floor in old/new position complete all as specified and as directed.

All as per item No 71 above, but 20mm bore.

All as per item No 71 above, but 25mm bore.

S&F gun metal gate / globe valves 15mm bore with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and as directed.

All as per item No 74 above, but 20mm bore.

S&F PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and directed.

M&L Concrete bed to drain pipes of 110mm bore including packing under and hauching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C-2 complete all as specified and directed.

S&F PVC (SWR) bends 110 mm bore any radius complete all as specified.

S&F Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges. complete all as specified.

S&F in repairs Fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and flynuts, screwed for iron pipe and fixed.complete all as specified.

S&F low density 32mm dia, polythene waste pipe (LDPE) of pressure rating 0.6 Kgf/Cm2.

S&F in repairs white vitreous china wash basin flat back, size 550 x 400mm including cast iron brackets, CP waste coupling 32 mm size ,cutting for and pinning in ends of brackets complete all as specified.

S&F grating round 100 mm size of PTMT. (Minimum weight 50gms) all as specified.

S&F Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long. complete all as specified.

S&F in repairs rotational moulded polyethylene water storage tank (multilayer quality) cylindrical vertical with closed top of capacity 1000 liters hoisted and fixed in position with connecting ports (inlet, outlet and over flows ) complete all as specified and as directed.

S&F ball valves 25mm bore high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. complete all as specified.

S&F stop valves, cast copper alloy, fancy type, chromium plated with long shunk and cup (concealed type), 15mm bore complete all as specified.

M&L 100mm thick, cement concrete 1:4:8 type C-2 (using 40mm graded stone aggregate) as in path / hardstanding / sub base of flooring. complete all as specified.

M&L Sand filling under floors or in foundation including watering and consolidation. complete all as specified. (Consolidated thickness shall be measured)

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade complete all as specified and as directed.

M&L for mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed, not less than 0.9mm dia or securing with clips complete all as specified.

Making good under cills or over arches, lintels and bressummers including all pinning as necessary in CM 1:4 complete all as specified and as directed.

Supply and fixing 50mm long butt hinges mild steel medium weight cold rolled etc. complete all as specified and as directed.

S&F 150mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

Cutting openings through walls built in cement mortar for door, window and other opening or enlarging existing openings. Etc or cutting out defective masonry for underpinning including providing, fixing and removing, shoring cleaning and stacking stone and removing surplus to store and rubbish off the premises.

M&L for brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and as direceted.

M&L for screed bed or bedding layer of cement mortar 1:6, 20mm thick for laying floor finishes. complete all as specified and as direceted.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. (screed bed shall be measured seperately)

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (screed bed shall be measured seperately) complete all as specified and as direceted.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering bent to curve and fixed with self drilling and self tapping screws, neoprene and limpet washers complete all as specified and directed.

Preparation of new plaster surfaces and applying three coats of white wash on wall complete all as specified and as direceted.

Preparation of old treated surfaces and applying one coat of white wash on wall complete all as specified and as direceted.

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15 deep and getting out in soft / loose soil complete all as specified and as direceted.

Dismantling & taking down aluminium service wire of any size including necessary disconnection from the pole / main switches etc. complete all as directed.

Dismantling house service bracket any type from the wall including making good the disturbed surface complete

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5m in depth for foundation or for laying of cables and getting out in soft / loose soil complete all as specified and as directed.

Supply and laying sand with approved fine grade around cable in cushioning for protection of under ground cable complete all as specified and as directed.(Punned thickness shall be measured)

Supply and laying in trenches or passing through pipe 1100 volts grade armoured heavy duty XLPE insulated electric cable with aluminium conductor of cross sectional area 6 sqmm 2 core complete all as specified and as directed

M&L for laying of sub class 'B' common burnt clay brick for protection of cable complete all as specified and as directed.

Returning, filling of soil in trenches including spreading, levelling, watering and well ramming in layers n.exc. 25 cm complete all as specified and as directed.

Removal of excavated soil n.exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point all as specified and as directed.

S&F GI Pipe 25mm bore light grade fixed for cable protection along with wall all as specified and as directed

Taking down carefully copper/Aluminum point wiring light fan, socket or power complete (fittings such as switches ceiling roses pendants, regulators, sockets, sketch light fittings, tube light fittings etc. to be measured separately if found serviceable) and removing unserviceable materials from site of work and segregating serviceable materials for safe custody and making good to disturbed surfaces of walls, floors, etc. including disconnecting of ceiling fan/exhaust fan complete all as directed

Taking down serviceable main switches, DB etc. any type and refixing the same after repair work of Bldg and making good disturbed surfaces to match with the existing finishes complete all as specified and as directed.

M&L Point wiring for light/fan/call bell etc. controlled by one switch with 1.50 Sqmm (nominal area) FRLS PVC insulated 1100 volts grade multi stranded copper conductor single core unsheathed cable drawn through and unsheathed single core solid copper conductor cable of size 1.50 Sqmm as earth continuity conductor connected to common earth dolly, including rigid PVC concealed conduit (Medium Grade) of suitable size, with all fittings and accessories including provision of mild steel terminal boxes of suitable size made with 1.2 mm thick mild steel sheet duly galvanised and suitable for fixing switches / sockets / regulators etc. fixed in recess of wall with brass chromium plated screws and cup washer complete for one light / fan point controlled by one switch all as specified and directed.

All as per item No. 116 here-in-before but for 5/6 Amp socket point on independent board -ditto-

All as per item No.116 here-in-before but with2.5 Sqmm cable for 15/16 Amp socket point on independent board and 2.50 sqmm solid copper cable for earth continuity conductor.

S&F Switch piano flush type, single pole, one way, 5/6Amp complete all as specified and as directed.

S&F Switch Socket combination, 2-in-1, 3 pin, 5/6 Amps flush type complete all as specified and as directed.

S&F Switch Socket combination, 5-in-1, 5/16 Amps flush type complete all as specified and as directed.

S&F Ceiling rose, surface bakelite, 3 terminals complete all as specified and as directed.

S&F electronic step regulator (speed regulation in 5 steps) suitable for ceiling fan 1200 / 1400 mm sweep 120 watts complete all as specified and as directed.

M&L for concealed sub-main wiring with two run of 6.0 Sqmm single core multi-stranded PVC insulated unsheathed copper conductor cable of 1100 volts grade FRLSH, alongwith one run of 6.0 sqmm single core multi-stranded copper conductor 1100 volts grade FRLSH PVC insulated unsheathed copper condutor cable as earth continuity conductor, drawn through and including rigid PVC conduit (ISI marked medium grade, of size not less than 19mm dia) with and icluding necessary cutting/chasing in wall/floor/ceiling etc and making good the distrubed surface and matching with the existing surface complete all as specified and as directed by the Engineer-in-Charge. Note : (i) Rates of PVC conduits and its accessories and cutting of chases in the wall / floor ceilig etc and making good the same after putting conduit, are deemed to be included in the unit rate. (ii) 2 run of single core cable (for Phase & Neutral), one run earth wire and PVC conduit shall be measured as one length.

S&F SPN MCB of capacity 32 Amps, 240 volts, complete all as specified and as directed.

Supply and fixing Green line smart luminaire of 40 watt LED street light luminaires with highly efficient lighting in & including mounting bracket made out of GI pipe light grade 32-40mm bore not less than 01 mtr long duly fixed with wall with fixing arrangement such as clamps, nuts, bolts complete all as specified and directed by the Engr in charge make- Philips cat part No BRP 409 LED 040 CW HO MR FG S1 PSU GR or equivalent from list of make as approved by GE.

S&F MCB, SP,240 volts, breaking capacity 10 KA, rating 6 to 32 amps, complete all as specified and as directed.

Taking down old serviceable/unserviceable ceiling fan, connecting wire etc and keeping at site for reuse at site after carrying out repiar works to building/rewiring complete all as specified and directed by the Engr-in-charge

Refixing old serviceable ceiling fan, connecting wire etc to building/rewiring complete all as specified and directed by the Engr-in-charge

Supply and fixing energy efficient, 5 star rated ceiling fan 1200 mm sweep, with all acceesories and connecting up with the ceiling rose with new flexible wire of suitable size complete all as specified and as directed. Make: Usha Energia Star ISI or equivalent make of Havells / Bajaj / Cropmpton / Khaitan

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of the earth plate not less than 1.5 m below ground level, connected to GI earth wire 4mm dia by means of bolts, nuts,check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part-I, connected to earth test point all as specified or indicated including excavation and connected earth work in soft / loose soil, P.C.C 1:3:6 type C-1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 15mm bore GI light grade earth lead protection pipe, 50mm thick R.C.C. 1:2;4 type B-1 cover slab of earth pit reinforced with 8mm dia TMT bars @ 10cm C/C both ways and with handle made out of 10mm dia bars, funnel, strainer,charcoal and testing on completion including dismantling unserviceable earthing complete all as specified and as directed.

S&F LED T8 tubular lamp 8 watt of cat part LTT8-8 of make crompton with decorative box type fitting of cat part No DMLN1LT8-8 of Make Crompton or equvalent make from list of make as approved by GE.

S&F Sheet Metal enclosure( IP-43) for SPN DBs,08Ways, Single Door, suitable for mounting DP MCB as incomer & SP MCBs as outgoings, built- in bus bars complete suitable for 240 Volts, AC, 50 Hz supply, and fixed in recess in brick masonary wall all as specified and as directed

S&F master LED tube 1200mm, 18w, retrofit type with one mounting rail heavy quality complete with side holders. Make : Philips, cat part No. TMC 501 P1XT-LED22W P324 (for mounting rail) and for LED tube rod cat part No. MAS LED tube 1200mm 18W865 T8 I or equavalent make from list of make as approved by GE.

S&F sheet metal enclosure( IP-43) for SPN DBs,04Ways, Single Door, suitable for mounting DP MCB as incomer & SP MCBs as outgoings, built- in bus bars complete suitable for 240 Volts, AC, 50 Hz supply, and fixed in recess in brick masonary wall all as specified and as directed

SHRI NARESH GUPTA

M/S Bikash Saha