TIRUPPUR CORP_Maintenance and Special Repair works to CHO Quarters at New Ramakrishnapuram in ward No.32.

Amount

Earthwork excavation for foundation in all soils and sub soils except in hard rock requiring blasting and depositing on bank with initial lead of 10m and initial lift of 2m inclusive of shoring, shuttering, bailing out water wherever necessary, refilling the foundation with excavated earth other than sandy soil in layers of not more than 150mm thick layers well rammed and depositing the surplus earth within the compound in place shown by the departmental officers and clearing and levelling the site etc,. complete.

Plain Cement concrete 1:4:8 [one cement, four M-sand and eight course aggregates] using 40mm size Hard Broken/Machine crushed Granite Stone Jelly including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted etc., complete complying with standard specification.

Random rubble masonry in CM 1:5 [one cement and five M-sand] for foundation and basement using best new rough and bond stones including simultaneous pointing above ground level with the same mortar etc., complete complying with standard specification.

Brick work In CM 1:5 mix using best Second Class Table Moulded Chamber Burnt Bricks 9"x4½"x3" having 350 kg/cm² compressive strength and 15% or less water absorbent in the period of 24hours immersement and confirming to ISI specifications including finishing, curing etc., complete complying with standard specification.

Plastering with cement mortar 1:5 mix (one cement five P-sand), 12mm thick in all floors using clean screened M-Sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting from other damages till setting of mortar etc., complete complying with standard specification.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc., conforming to IS specification including primer coating and enamel painting as per design given by the departmental officers etc., complete as per standard specification.

Fabricating supplying and fixing of Galvalume Colour Sheet of size 0.47mm with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47mm thick 24 gauge having width 1050mm. The sheet should be G.I base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws and plastic washer. The washer and screws to be fixed by using minute power machine drilled without damaging the sheets paint coating to be regular modified polyester coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like Malabar Mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required size and making ornamental designs as per the site condition and as directed by the departmental officers.

Weathering Course with Brick jelly lime concrete made in Broken Brick Jelly 20mm gauge in pure slaked lime (no M-Sand to be added) laid over roof slab, the proportion of brick jelly to lime being 32 to 12.5 and well beated with wooden beaters for giving required slope and thickness etc., complete complying with standard specification.

Finishing the top of the roof slab with one course of Machine pressed tiles of size 20cm x 20cm x 2cm of approved quality laid in cement mortar 1:3 [one cement and three M-Sand] 12mm thick mixed with waterproofing compound 2% by the weight of cement used and the top pointed with same mortar etc., complete complying with standard specification.

Supplying and filling Well gravel in layers of not more than 15cm thick well rammed, watered and compacted etc., complete complying with standard specification.

Providing and laying, spreading and compacting graded stone aggregate to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Providing and laying of 63mm thick Rubber Moulded Hydraulic Pressed Paver Block in uniform shape of approved make to be laid in flurring bond pattern with 150mm thick quarry rubbish cushion below the uniform shape of approved non-skitting surface in the top and the rates including levelling the base, preparation of pavers as sub base, quarry rubbish cushion 150mm thick, laying out of pavement, cut the pieces to fix the edge, vibring the pavers, sweeping, transporting, loading and unloading etc., complete complying with standard specification.

UPVC Window Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Window of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works)

Flooring with 50mm thick Cuddapah Slab over a base of CM 1:3 (one cement three M-sand), 20mm thick and pointed with cement mortar 1:3 using black oxide etc., complete complying with standard specification.

Dadooing the walls with Colour Designed glazed tiles of size 300mm x 200mm x 6mm of approved make and quality in cement mortar 1:2 mix [one cement and two M-sand] over 10mm base layer plastering and pointing with white cement neatly etc., complete as per standard specification.

Painting two coats with ready mixed Plastic Emulsion paint (weather proof) of approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt and including necessary plaster of paris, putty wherever required etc., complete as per standard specifications.

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Providing Wooden Cubboard arrangements including all labour charges, Transporting and fixing charges etc., complete

Supply and fixing in position of 12 Volt 180 AH Lead Acid, Sealed Maintenance Free (SMF) Batteries with connecting leads, lugs terminal post etc., as per standard methods and including conveyance all incidental charges, necessary scaffolding and re-doing the dismantlted portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the Departmental officers. Make : Excellent / Safety First / Equivalent.

Supply and fixing of HUPS SW LGS1 100/12V including Transporting , fixing of Labour Charges etc., complete.

Add GST @ 18%

Raaj and co