SPL REPAIRS TO BLDG NO P-21 (FAFA) OR MD ACCN AT JADUNATH ENCLAVE UNDER GE (NORTH) UDHAMPUR

Amount

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. ) , all as specified and directed.

Description all as per item No 01 above but area exceeding 1.50 square metre and not exceeding 4 square metre each.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawing complete all as specified and as directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and as directed.

Pressed steel frames for doors, made out of 1.25 mm thick MS sheet, with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 125 mm x 60 mm, including one shop coat of red oxide zinc chrome primer, including filling voids with PCC 1:3:6 type C-0 complete all as specified and as directed.

Description all as per item No 05 above but frame size 105 x 60mm.

Mild Steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, conforming to Fe 410-W (Gde-E- 250) quality-A, complete all as specified and as directed.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar, barred iron doors; ladder, framed balusters; railing; frame work for water tanks, cooler stand etc and similar work conforming to FE 290-0 or Gde-E-165, complete all as specified and as directed.

Plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) for filling in the pressed steel door frame/hold fast complete all as specified and as directed.

30mm thick flush shutters, solid core construction, with block board core and plywood face pannels and both face is covered with decorative face veneer with liping/frame to match, complete all as specified and directed.

Description all as per item No 10 above but glazed and skeleton shutter with sash bar for glass/wire gauge, complete all as specified and directed.

18/19mm thick Prelaminated particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive complete all as specified and as directed.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staples complete, all as specified and directed.

150mm Double action spring hinges, mild steel with steel wire spring, stove enamelled, black, complete, all as specified and as directed.

75mm butt hinges ,medium weight ,cold rolled mild steel all as complete all as specified and directed.

300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete, all as specified. (ISI Mark)

250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete, all as specified. (ISI Mark)

200 mm aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. (ISI Mark)

150 mm aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. (ISI Mark)

100 mm aluminium handles, cast type anodised complete all as specified and directed. (ISI Mark)

150 mm aluminium handles, cast type anodised complete all as specified and directed. (ISI Mark)

Hasp and staple, 100 mm size safety type aluminium anodised with mild steel hinges pin, including bolt to hinge plate and fixed with screws, all as specified .

125 mm aluminium handles, cast type anodised complete all as specified and directed. (ISI Mark)

125 mm aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. (ISI Mark)

Continuous (piano) hinges width of flaps 30 mm when opened, mild steel, bright finish or electrogalvanised complete all as specified and as directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, 150mm overall length of cover plate complete all as specified and directed. (ISI Mark)

Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing, glazing pins/aluminium beading, etc. including powder coating of thickness minimum 50 micron, complete all as specified and as directed.

Powder coating of any colour (Thickness or powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified as per CEUZ TD drawing.

Aluminium deco grill of 5 to 6mm dia size of mesh not exc 7.5cm in either direction including Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge.

4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified.

4 mm thick figured glass (frosted) ,pin head type and glazing with oil putty not exc 0.50 Sqm in each pane fixing to window/ventilator complete all as specified and as directed.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantling portion in CM 1:3 and making good in cement concrete 1:2:4 type B1 as required exc half brick but n exc one brick, complete all as specified and as directed.

Preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide/zink chrome primer complete, complete all as specified and as directed.

Preparation of new wooden or wood based surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and as directed.

25 mm thick, Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in sub base for laying floor finishes including finishing the surfaces even and rough without using extra cement, complete all as specified and as directed.

Non skid, coloured, ceramic jointfree/rectified tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and as directed.

Non skid, coloured, white printed ceramic jointfree/rectified tiles 10mm thick (square/rectangular) (600x600) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Glazed coloured ceramic jointfree/rectified tiles of size 450x300mm 7mm thick in vertical surfaces like dado/skirting, etc., set and jointed in neat cement slurry and pointed in coloured cement to match, over and including 10 mm thick rendering on fair faces of brick/concrete surfaces works in cement mortar 1:3 finished rough for receiving tiles, complete all as specified and as directed.

20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting and mirror finish polishing over and including 20 mm thick screed bedding/ backing layer in CM 1:4, complete all as specified and as directed.

Machine cut kota stone single piece slab flooring 20-25 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including Screed bed or bedding layer of mortar 20mm thick in cement mortar 1:4, complete all as specified.

Machine cut kota stone single piece slab flooring 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over cement screed base and jointed with white cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, over and including 10 mm thick rendering in cement mortar 1:3 as in backing coat for laying wall tiles, complete all as specified and as directed.

PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

Stop valve, fancy type chromium plated cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore 15mm, fixed in repairs, complete all as specified and as directed.

Brass Chromium plated over head shower rose of dia 125mm with swivel joint fixed to pipe or union of 15mm bore, fixed in repairs, complete all as specified and as directed.

Stop valves, fancy type, chromium plated, cast copper alloy, with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore 15mm fixed in repairs, complete all as specified and as directed.

Tubular towel rails brass chromium plated, 20 mm dia, D type, 60 cm long between flanges, with chromium plated brass screw in wooden/plastic cleat, fixed in repairs, complete alll as specified and as directed,

Soap dish, stainless steel, approximate size 160x 160x90mm fixed to plugs with chromium plated brass screws, complete all as specified and as directed.

Bib taps , fancy type cast copper alloy, chromium plated, with crutch or butterfly handle screwed down for iron pipe or for brass ferrule for bore of pipe 15 mm, fixed in repairs, complete all as specified and as directed.

Brass CP mixer for mixing hot & cold water screwed down for iron pipe for wash hand basin with wall flange, complete all as specified and as directed.

Sink mixture with regular swinging spout wall mounted with connecting legs & wall flanges, complete all as specified and as directed.

Plate rack made of stainless steel, 750 x 900X250mm and thickness of SS strip of 1mm including fixing as per manufacturers instruction complete all as specified.

Sinks made of stainless steel with draining board, made out of 1.00mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar including fixing cantilever brackets connecting union to pipe and 32mm dia GI pipe duly painted upto Nihani Trap or Floor trap complete as directed at site, overall size 915mmx460mm bowl size 410mm x 330mm x160mm, in repairs complete all as specified.

Mirror cabinet PTMT of 450mm x 600mm with magnetic looking arrangements fixed with and including chromium plated brass screws and PVC rawl plugs, complete all as specified and directed.

25 mm dia SS curtain rods in repair with bracket and knobs at both ends as per site requirement including taking down old existing PVC conduit pipes with accessories, complete all as specified and directed. Note: The cost of brackets and knobs is deemed to be including in the quoted rate. Nothing extra shall be paid on this account.

Taking up or down steel tubing of 15 mm bore with connections for cleaning for refixing or removing to store yard/from site, complete all as specified and as directed.

Taking up or down steel tubing of 20 mm bore with connections for cleaning for refixing or removing to store yard/from site, complete all as specified and as directed.

Taking up or down steel tubing of 25 to 32 mm bore with connections for cleaning for refixing or removing to store yard/from site, complete all as specified and as directed.

15 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and as directed.

20 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and as directed.

25 mm bore steel water tubing medium grade galvanised with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and as directed.

Refixing old 15mm steel tubing and connections in new or old position (Walls, ceiling, floors etc.), complete all as specified and as directed.

Refixing old 20mm steel tubing and connections in new or old position (Walls, ceiling, floors etc.), complete all as specified and as directed.

Refixing old 25mm steel tubing and connections in new or old position (Walls, ceiling, floors etc.), complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes/soil pipes (any size, type or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., for (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and as directed.

Cast iron floor trap 75mm size, plain with SS grating including jointing with solvent cement fixing in repairs, complete all as specified and as directed.

Dismantling cast iron pipe & reinforced concrete drain pipes, jointed in cement mortar of any dia taking out from trenches or fixed to wall upto 100mm complete all as specified.

Dismantling cast iron pipe & reinforced concrete drain pipes, jointed in cement mortar of any dia taking out from trenches or fixed to wall upto 75mm complete all as specified.

Cast iron soil, waste and vent pipes (Spun pipes) in any length with or without ears, with cement joints fixed to wall or in floors of 75mm bore, complete all as specified and as directed.

Cast iron soil, waste and vent pipes (Spun pipes) in any length with or without ears, with cement joints fixed to wall or in floors of 100mm bore, complete all as specified and as directed.

Cast iron bends with oval access door (any radius), diminishing pieces or tapers (larger bore measured) for 100mm bore pipe, all as specified and as directed.

Cast iron bends with oval access door (any radius), diminishing pieces or tapers (larger bore measured) for 75mm bore pipe, all as specified and as directed.

Cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 100 bore, fitted with oval access door as in repairs complete all as specified and as directed.

Cast iron branch pieces, double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 100 bore, fitted with oval access door as in repairs complete all as specified and as directed.

Cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 75 bore, fitted with oval access door as in repairs complete all as specified and as directed.

Cast iron branch pieces, double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 75 bore, fitted with oval access door as in repairs complete all as specified and as directed.

Cast iron vent cowl for 100 mm bore pipe, complete all as specified and as directed.

Cast iron vent cowl for 75 mm bore pipe, complete all as specified and as directed.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20mm fixing in repairs, complete all as specified and as directed.

Vitreous China wash down water closet pan and seat cover (pedestal pattern), coloured (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, including connection to drain pipe (or out going pipe) and to flushing pipe, antisyphonage pipe, etc. including cast iron 'P' or 'S' trap for 100mm bore of pipe, fixed in repairs complete all as specified and as directed.

10 ltr capacity PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, fixed in repairs, complete all as specified and as directed.

Viterous china wash basin, white flat back size 550 x 400mm incl waste couping CP 32mm dia chain and plug and porcelan stopper and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP grating with holes with pedestal of china ware fixed in repairs complete, all as specified and as directed.

Taking down old PCC tiles from roof and removing bedding and existing treatment of any description and any type, at any position, complete all as specified and as directed.

15 mm thick rendering on roof surfaces in cement mortar 1:4 and finished even and smooth without using extra cement and mixing water proofing compund in the proportion as mentioned in manufacturer's instructions complete all as specified and as directed. Note : Water proofing compund to be measured and paid for separately as supply only.

Chequered cement concrete tiles 30cm x 30cm x 20-25mm thick, with mixture of white & grey cement in equal proportion & no pigment set, jointed and pointed in neat cement slurry in floors, laid over 15mm thick screed bed in cement mortar 1:4 complete, all as specified and as directed.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 10mm thick plastering in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric five layred APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.5 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm & including two coats of bituminous Aluminium paint, complete all as specified and as directed.

Supply only Integral water proofing compound, complete all as specified and as directed.

Providing, Plain cement concrete 1:2:4, type B-0 (using 20 mm graded stone aggregates) in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, removing all type of vegetation (like peeple tree etc) scrubbing down with water complete, all as specified and as directed.

10mm thick rendering on other than fair faces of brick or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement, complete all as specified and as directed.

15 mm thick rendering in two layer (10mm + 5mm) on fair faces of brick /concrete on wall including facia chhajja etc.surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing integral water proofing compund in the proportion as mentioned in manufacturer's instructions complete all as specified and as directed. Note : Water proofing compund to be measured and paid for separately as supply only.

5mm thick rendering on brick or concrete surfaces as in ceiling in cement mortar 1:4, and finish the surface fair and even without using extra cement, complete all as specified and as directed.

Reinforced cement concrete 1:2:4 type B1, (using 20 mm graded crushed stone aggregate) as in chajjas, complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius in half brick thick built in cement mortar 1:4, complete all as specified and as directed.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and as directed.

Providing 75 mm thick cement concrete 1:3:6 type C-2 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints through out the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed.

Demolition of Cement Concrete of any description and in any position not otherwise specifically provided for including and disposal of unserviceable material, debris and rubbish to a distance n exc 100m complete all as specified and as directed.

Reinforced cement concrete M-25 design mix, (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and including binding with MS wire (annealed not less than 0.9mm dia), complete all as specified and as directed.

TMT mild steel bars, 6 to 8mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and includingMS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc to obtain rough flat finished surface of concrete complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed.

Rotational moulded polyethylene water storage tank, two layers, inner and outer white, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories {i.e GI nipples and Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of bore 20mm (Minimum weight 210 gram) etc}, incl dismantling existing water tank, complete all as specified and as directed.

Preparing new plastered surfaces and applying 1 to 2mm wall care putty in wall surface and smoothening the surface with sand papers/ Mechanised sanding etc and applying two coat oil bound distemper of approved tint over a coat of alkali resistant primer, complete all as specified and as directed.

Preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed.

Preparing newly plastered or unplastered surfaces of wall and applying two coats of cement base paint, complete all as specified and as directed.

Eye door viewer (Magic eye) fixed in position for shutters, fixed in repairs, complete all as specified and as directed.

Rubber sheet 50mm wide and of thickness not less than 3mm fixed with stainless steel screws at bottom of the door shutters as in door cile, complete all as specified and as directed.

Stainless steel fancy type peg set colour coated of four and fixed in poistion with steel screws, complete all as specified and as directed.

Grinding and polishing existing kots stone flooring, complete all as specified and as directed.

Stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where everrequired) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and as directed.

Taking down carefully copper /aluminium, point wiring (light, fan, socket or power) complete including fittings and fixtures such as light fittings, switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of wall, ceiling, floors etc to match the existing, complete all as specified and as directed.

Point wiring for light/fan/exhaust fan/bell point using approved color coading as per IS code (Red,Black and Green for single phase circuit) with multi stranded copper condutor 1.5 Sqmm nominal cross section area,single core,PVC insulated and unsheathed FRLS cable 1100V grade,in and including medium grade,PVC concealed conduit ISI marked of dia not less than 20mm and conduilt accessories concealed in wall/roof/floor etc GI anealed metal box 1.2 mm thick switch board of suitable size be fixed flush wall , with 3 mm thick ebonite sheet cover and necessary screws, cap washers etc. PVC insulated PVC insulated multistranded copper condutor 1.5 sqmm nominal cross section area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed.

All as per item No. 116 above but for One bell/ buzzer point controlled by one push button on the same board with other switches or independent, complete all as specified and directed.

Description all as per item No 116 above but 05 Amp socket outlet 3 pin controlled by one switch on independent board.

Description all asper item No 116 above but one 3/5 pin 15 Amp socket outlet on independent board with PVC insulated, unsheathed FRLS cable 2.5 Sqmm copper multistrand conductor, along with PVC insulated and unsheathed FRLS 2.5 Sqmm multistrand copper conductor earth wire connected to common earth dolly complete all as specified and as directed.

Description all as per item No 116 above but 3 pin, 05 Amp socket outlet controlled by one switch on same board with other switch.

Description all as per item No 116 above but for one light point controlled by 2-two way switches.

Switch piano, flush type, single pole, one way, 5/6 Amp, complete all as specified and as directed.

Switch socket outlet, 2 in 1, 3 pin, 5 Amp flush type , complete all as specified and as directed.

Switch piano, flush type, single pole, one way, 15/16 Amp, complete all as specified and as directed.

Switch socket outlet, 2 in 1, 3 pin, 15/16 Amp flush type , complete all as specified and as directed.

Bell push 6 Amps 230 volts complete all as specified and as directed.

Switch Piano flush type single pole two way 6 Amps, complete all as specified and directed.

Ceilling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block, complete all as specified and as directed.

Fan regulator 120W, 230V 50 C/S, flush type electronic, step type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and as directed.

Bell (ding dong type), AC electronic type, 230 volts, single pole ,fixing in repairs, complete all as specified and as directed.

LEDT5 PC batten (100Lm/W) 1x 20W, 220V AC, PVC housing, PC cover ensures and glare free light IP 20 connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed.

LEDT5 PC batten (100Lm/W) 1x 10W, 220V AC, PVC housing, PC cover ensures and glare free light IP 20 connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed.

LEDT5 PC batten (100Lm/W) 1x 05W, 220V AC, PVC housing, PC cover ensures and glare free light IP 20 connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed.

LED light fitting 1x9W/1x10W bulkhead luminaires including LED light driver holder connecting up with 3 core flexible copper conductor cable of suitable size, complete all as specified and as directed.

LED street light fitting 35 watt 230V AC outdoor type with high pressure diest cast aliminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal managment in multiple optics complete with IP 65/66 protection, complete all as specified and as directed.

Taking down ceiling / exhaust fan, sealing cable end, dismantling blades and removing fan and blades to store, incl oiling, greasing, cleaning slot, overhauling & replacement of defective nut, bolt , washers etc. and applying two coat painting with synthetic enamel to fans complete, in situ by spraying including filling cavities with filler, one coat after cleaning all dust etc., making all connection using 1.5 sqmm copper conductor multi strand PVC insulated 2 core flexible cable from ceiling rose and rehanging/ refixing complete all as per the directions of Engg-in-Charge.

Supply and fix exhaust fan, steel body, copper windind, double bearing AC single Phase. 230V of size 300m sweep with, 4 blades, and iron frame and iron louvers complete all as specified and as directed.

PVC body air freshner fan, copper windind, AC single phase of size 150mm with louver including making necessary hole for fixing of fan etc, complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to and including 4mm dia galvanized iron wire lead by means of bolts, nuts, check nuts and washers of galvanized standard iron or steel all as specified or indicated in electrical plate No 3 of MES Part-I, including testing on completion including the material and labour and taking out old unserviceable earthing of the following :- (a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1. (c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified.

Srl item No 139 Contd … (e) 15 mm nominal bore light grade GI protection pipe 7.5 mtr long for protection of earthing lead from mechanical injury or tempering. (f) Requisite quantity of common salt and charcoal. (g) Testing of earthing. Note : On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4sqmm galvanised iron or steel wire complete all as specified and directed.

Supply and fixing sheet metal enclosures for DBs when 125 Amps MCCBs to be used double door DB VTPN 4 ways (optimum F1+ 12) with metal door 415 volts grade IP 42 protection grade fixed flush to wall complete including connections should be provide with necessary reduce lugs, complete all as specified and directed.

MCCB 4 pole , 415Volt, adjustable type, 125 Amps with breaking capacity 36 KA, complete all as specified and directed.

Sheet metal enclosures for distribution board when MCB to be used SPN 8 way with IP-43, IK-09 protection 240V with 100 Amps rated bus bar, double door type including taking down old making good the distubed surfaces to match with existing specifications, complete all as specified.

MCB SPN, 40 Amps, 240 Volts, rupturing capacity 10 KA "C" Series including providing aluminuium thimbles for outgoing cable, fixed in repairs, complete all as specified and as directed.

MCB SP, 6 to 32 Amps,240 Volts, rupturing capacity 10 KA "C" Series including providing aluminuium thimbles for outgoing cable, fixed in repairs, complete all as specified and as directed.

MCB SP, 63 Amps,240 Volts, rupturing capacity 10 KA "C" Series including providing aluminuium thimbles for outgoing cable, fixed in repairs, complete all as specified and as directed.

Sheet metal enclosure single pole & neutral with 2 pin and earth plug and socket 20Amps, 240V complete with and including one single pole MCB of 20 Amps and breaking capacity 10KA, complete all as specified and as directed.

Taking down old serviceable/unserviceable Electric meter including meter box from existing position carefully refixing including making good to disturbed surfaces , complete all as specified and as directed. (Note: Disturbed surfaces should making good by plastering/distembering/colour/washing/white washing to match with existing surfaces).

Sub main wiring with two runs of 6 Sqmm ( 2x6 sqmm ) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor conforming to IS-694 drawn through and including non-metalic PVC rigid conduit 25 mm dia ISI marked with all conduit accessories mounting on suface of walls /roofs / ceiling etc with one run of 6 Sqmm (1x6sqmm ) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire, fixed in repair, complete all as specified and directed by Engr-in-Charge. Note:- 2 runs of 6 Sqmm (2x6sqmm ) ,one run of 6 Sqmm (1x6 sqmm ) cable and one metre of conduit will be measured as one unit.

SupplyIing, laying / fixing and testing in replacement XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core in trenches/floor/pole/GI pipe complete including cutting/chasing to any surface and making good to the disturbed surface to match the existing, complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, and for laying of cable or pipes etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil, complete all as specified and as directed.

Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in any type of soil,complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and as directed.

Dry coarse sand as cushioning to under ground cable provided with layer of 8 cms deep before laying the cable and 15 cms deep after laying and stretching the cable, punned to 18 cm thick complete all as specified and as directed. NOTE Only punned thickness shall be measured for payment purpose.

Sub class ‘B’ old size well burnt bricks, laid flat in trenches as protection to cable complete all as specified and as directed.

GI tubing light grade 40mm dia along the wall/in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holding of GI pipe alongwith poles, complete all as specified and as directed.

S K BROTHERS (BID ID -3250349)

VIRINDER SINGH (BID ID -3249601)

M/S GURU DEV BUILDERS (BID ID -3256075)

paras ram pachiala (BID ID -3249136)

RAMAN KUMAR (BID ID -3256094)

takashdeep traders (BID ID -3249718)