NIT NO: 360/TC/2026-27

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material tobe used or auctioned up to a lead of 1000 meters including removal and disposal of top organic soil not exceeding 150 mm in thickness if required and as per relevant lauses of section- 200. A In area of light jungle

Granular Sub-base as per Table:- 400-1 Construction of granular sub-base by providing graded Material, ,carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface watering, rolling and compacting with vibratory power roller at OMC to achieve the desired density, complete as per clause 401 A Plant mix method (with Mechanically crushed stone only) a For Lower Sub-base with i Grading-V Material

Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per clause 406.)

Prime coat (Providing and applying primer coat with oil based bitumen emulsion (SS-1, grade confirming to IS:8887) on prepared surface of granular Base including clearing of road surface and spraying primer using mechanical means as per clause 502.

Tack coat Tack coat Providing and applying tack coat with bitumen emulsion (RS-1, grade confirming to IS:8887) using emulsion pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom and as per clause 503.

Bituminous Macadam (Providing and laying bituminous macadam as per clause 504 with mixed prepared in minimum 40-60 TPH capacity hot mix plant using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction) A premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction)

Close Graded Premix Surfacing/Mixed Seal Surfacing (Mechanical means using minimum 40-60 TPH capacity of HMP. Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness using bitumen to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a Smooth wheeled roller 8-10 tonne capacity, and finishing to required level and grade, complete as per clause 508) II With mechanical paver finisher A With bitumen

Providing and laying of a reinforced cement concrete pipe duct, 300 mm dia., across the road ( new construction ) , extending from drain to drain in cuts and toe of slopes to toe of slopes in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipes as per IRC: 98-2011, bedded on a 0.3 m thick layer of granular material free of rock pieces , outer to outer distance of pipes at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts ,joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC:98-2011 and approved drawings. Single row for one utility service

Providing and laying Reinforced Cement Concrete pipe NP 3 /prestressed concrete pipe. (Laying Reinforced cement concretepipe NP3 / prestressed concrete pipe for culverts including fixingcollar with cement mortar 1:2 but excluding bedding below ipes,excavation, protection works, ackfilling, concrete and masonry works in head walls and parapets . ) B 600 mm dia

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.) A Ordinary soil i Upto 3 m depth

Sand Filling in Foundation Trenches as per Drawing & Technical Specification

Plain/Reinforced cement concrete in open foundation complete as per drawing andtechnical specifications i PCC Grade M15

Plain/Reinforced cement concrete in open foundation complete as per drawing andtechnical specifications ii PCC Grade M20

Providing and laying Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications section 1500, 1700 and 2200 A Height upto 5m a Using concrete Mixer I P.C.C. Grade M-20

Providing and laying Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications section 1500, 1700 and 2200 (Newly laid concrete shall be covered by gunny bags). A Height upto 5m (a) Using concrete Mixer R.C.C. Grade M-20

Furnishing and Placing Reinforced/Prestressed cement concrete in super structure as per drawing and Technical Specification sections 1500, 1600 and 1700 B RCC Grade M30 I For Solid Slab Super Structure a Using Concrete Mixer I Height upto 5 m

Supplying, fitting and placing HYSD bar reinforcement in super-structure complete as per drawing and technical specifications and 2200

Providing and fixing in position tar paper bearing for slab as per approved drawing and specification

B Filler joint Providing & fixing 20 mm thick compressible fiber board ( 12 m long x 25 cm deep ) in expansion joint complete as per drawing & Technical Specification.

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification 710.1.4 of I.R.C. 78 and 2200

Providing weep holes in Brick masonry/ Plain/ Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specifications section 2706 and 2200

Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specifications 710.1.4 of I.R.C. 78 and 2200

Retro- reflectrorized Traffic signs (Providing and fixing of retro-reflectrorized cautionary, mandatory and informatory sign as per IRC :67-2012 made of retro-reflective type sheeting vide clause 801.3,fixed over aluminum sheeting of required thickness supported on a mild steel back frame of ISA 40 x 40 x 5 mm and mild steel angle iron post 75 mm x 75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45cm x 60cm, 60cm below ground level as per approved drawing and painting all components of the signs and supports as per clause 7.2 of IRC:67-2012) C Made of Class -A High Intensity Super Engineering Grade Sheeting of Type II (for ODR &Village Road) a) With Aluminum Sheeting of 2 mm thickness i 600 mm equilateral triangle

Retro- reflectrorized Traffic signs (Providing and fixing of retro-reflectrorized cautionary, mandatory and informatory sign as per IRC :67-2012 made of retro-reflective type sheeting vide clause 801.3,fixed over aluminum sheeting of required thickness supported on a mild steel back frame of ISA 40 x 40 x 5 mm and mild steel angle iron post 75 mm x 75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45cm x 60cm, 60cm below ground level as per approved drawing and painting all components of the signs and supports as per clause 7.2 of IRC:67-2012) C Made of Class -A High Intensity Super Engineering Grade Sheeting of Type II (for ODR &Village Road) a) With Aluminum Sheeting of 2 mm thickness ii 600 mm circular

Type A : Village boards (600 mm long, 300 mm wide at bottom & 100 mm wide at top, and height 600 mm above 500 mm thick block of size 700 x 400 x 500 mm with both faces inclined )

Direction and Place Identification signs with size more than 0.9 sqm size board. (Providing and erecting direction and place identification retro- reflectorized sign as per IRC :67-2012 made of retro-reflective type sheeting and vide clause 801.3, fixed over aluminum sheeting, 2 mm thick with area exceeding 0.9 sqm and fixed on a mild steel frame of size 40 x 40 x 5 mm supported on 2 Nos. mild steel angle iron posts of size 75 mm x 75 mm x 6 mm,firmly fixed to the ground with M 15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing) C Made of class - A High intensity Micro prismatic grade Sheeting of Type 1 (for ODR &Village Road)

Kilo Meter Stone (Reinforced cement concrete M15grade kilometer stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc) Ordinary Kilometer stone (Precast)

Kilo Meter Stone (Reinforced cement concrete M15grade kilometer stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc) Hectometer stone (Precast)

Providing & Fixing Hazard Marker Type-2 Partial Retro Reflective Size 0.30 x 0.90M made of 16 gauge (1.6 mm) thick mild steel sheet Confirming to IS:2062 Painted with one cast of Zinc Chromate Stoving Primer and two coats of Black Stove Enamel (Oven Baked) paint with 10 cm bands of yellow Retro- Reflective Sheeting of Engineering Grade pasted a per IRC:79 including one MS angle Iron post of size 50x50x5 mm of 1.65 meter long duly painted with synthetic enameled paint block including bolts and fixing the same in M- 15 concrete black of size 30x30x30cm, including transportation etc. Complete.

Providing and Fixing Linear Delineator System as per MOST clause 806 of specification for Roads and Bridges, of size 33‟'x 4” made with corrugate Aluminum (Confirming to IS:736 - Material Designation, 24345; or 1900) and reflective sheeting of Micro prismatic Lens sheeting as stipulated in MOST circular (RW/NH- 33023/31/88-DO.iii) confirming to ASTM D4956-01 Type IX and fixing the same with bracket made of galvanized steel fixed with 6 Nos. high precision Screws confirming to IS:1364.

Providing & Fixing tree studs in Square/ Round shape of 4” side/diameter made of 2 mm aluminum substrate (Confirming to IS:736 -Material Designation, 24345 or 1900) end reflective surface of High Intensity grade as specified in section 801.3 of MORT&H duly treated with HLVA and fixing the same with four Nos. high strength nails confirming to 1S:1367 on trees at site each.

Providing and fixing guard stones 200 x 200 x 900 mm made of precast RCC M-20 grade fixed at 300 mm into the ground in P.C.C. 1:3:6 blocks of size 400 x 400 x 400 mm and given two coats of paint with white and black bands including excavation.

Construction of RCC open drain Construction of RCC open drain 0.60m x 0.60m inside dimension lined with 120 mm thick RCC M-20 walls, 120 mm thick CC M-20 foundation, over 100 mm thick (Av) leveling course in PCC M-15 including excavation , dressing of sides and bottom, provision of HYSD reinforcement consisting 8 mm dia horizontal bars @ 150 mm c/c and L-shaped 8 mm dia vertical bars @ 150 mm c/c (L= 800 mm) including cutting , bending and binding wire, placing in position , providing shuttering and concreting by using concrete mixer, compaction by vibration etc complete as per drawings and technical specifications.

RCC drain/chamber cover Construction of RCC drain/chamber cover, placing in position,providing shuttering and concreting by using concrete mixer, compaction by vibration etc complete as per drawings and technical specifications excluding reinforcement. with RCC M-20

Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in drain/cover/chamber complete as per Drawing and Technical Specifications.

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.) Ordinary soil Up to 3 m depth

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications. PCC Grade M-15

Providing and laying Filter material underneath pitching in slopes complete as per drawing and Technical specification including trimming of slopes to proper profile and preparation of bed and as per clause 2504.

Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications as per section 2504. Cement Concrete blocks of size 0.3x0.3 x0.3 m cast in cement concrete of Grade M15

UOM Name

Percentage

Per mile

Siemens Per meter

Activity unit

Batch