Renovation of office of CEO HARIS Room DITS in Mini Sectt. at Gurugram (Only Civil Works)

Amount

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 1000x1000 mm Note:- Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material (N.S)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete Size of Tile 1000x1000 mm Note:- Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material (N.S)

Providing and fixing wooden solid partitions with 2"x2" wooden from of Commercial hard wood such as hillock, champ, chikrassy and chaplash etc. (Non Coniferous timber other than teak conforming to I.S specification No. 1003 kiln seasoned) wrought, planed and fixed in position 12mm thick 3 ply decorative ply wood with teak faced on one side plywood, plain lining butt- jointed, including wooden plugs (Teak, Placed at 45cm to 60cm centres, complete with necessary nails including Melamine Polishing complete in all respect as desired by Engineer-in-Charge (NS). Note the agency to whom the work is allotted will have to produce original bill/ voucher for all quantity in token of proof of purchase of material.

11.43 cm thick brick wall laid in cement(HSR 11.48a)

12 mm thick cement plaster 1:6(HSR 15.7)

15 mm thick cement plaster 1:6 on the rough side of single of half brick wall(HSR 15.12)

Providing & fixing ceramic tiles/ anty skid tile of size 400mm X 400mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles Note:- Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO(HSR 14.91) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material

Providing & fixing Ist quality ceramic glazed wall tilesconfirming to IS 15622 (thickness to be specified by manufacturer)of approved make in all colors,shade except burgundy,bottlegreen,black of any size as approved by engineer-In Charge in skirting ,risers of steps and dados over12mm thick bed of cement mortor 1:3 coarse and jointed with grey cement slurry,including pointing in white cement mixed with pigment to match the shade complete. Size of ceramic Glazed tiles 300mm X 450mm(HSR 14.92 b) Note:- Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material

Providing and fixing mineral fiber false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern, The Tiles should have Humidity Resistance (RH) of 99%, Light Reflectance 785%. Thermal Conductivity K = 0.052 - 0.057 w/m K, Fire Perforamce as per (BS 476 pt - 6 & 7) in true horizontoal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33mm thick (galvanized @ 120gsm) comprising of main T runner of 15x32mm of length 3000mm, cross T of size 15x32mm of length 1200mm and secondary intermediate cross T of size 15x32mm of length 600mm to form grid module of size 600x600mm suspended from ceiling using galvanized mild stell item (galvanized @ gsm) 50mm long 8mm outer diameter M-6 dash fasteners, 6mm diameter fully threaded hanger rod up to 1000mm length and L-shape level adjuster of size 85x25x2mm, spaced at 1200mm centre to centre along main T . The system should rest on periphery wall/ partitions with the help of GI parimeter wall angle of size 24x24x3000 mm made of 0.40mm thick sheet, tobe fixed to the wall with help of plastic rawl plug at 450mm centre to centre & 40 mm long dry wall S.S screws, THe exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drwings and as per directions of the Engineer-in Charge. with or without groves. (HSR: 13.92)

Providing and fixing 8mm thick toughend glass complete in all respect. The work shall be carried out as per specifications, drawings and as per directions of the Engineer-in-Charge(N.S) Modi, Saintgobian etc. Note:- The agency to whom the work is allotted will have to produce original bill/ voucher for all quantity in token of proof of purchase of material.

Providing and fixing plywood, plain lining butt-jointed, including wooden plugs (Teak, Placed at 45cm to 60cm centres, complete with necessary ails) 18mm thick Note:- The agency to whom the work is allotted will have to produce original bill/ voucher for all quantity in token of proof of purchase of material. . (N.S)

Factory manufacture solid flush door and Shutters, with block board core as per I.S. No. 1659-1969 bonded with water poof type phenol formal dehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in positon includeing iron hinges, screws, chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- as per HSR 17.93 a iii. (Note) :- Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges. (Duro, Green) 35 mm. Thick (HSR 17.93a iii- note I under 17.18))

Providing and fixing roller blinds of approved make. complete in all respect(N.S) Note:- The agency to whom the work is allotted will have to produce original bill/ voucher for all quantity in token of proof of purchase of material. The make/ quality and design shall be got approved before start the work.

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 100X58X1.90 mm(DSR 9.70.2)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 15 mm dia nominal bore(DSR 18.10.1) Make:- UNIK, TATA, ZOLOTO.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 20 mm dia nominal bore(DSR 18.10.2) Make:- UNIK, TATA, ZOLOTO.

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUITE, SYPHONIC TYPE, Consisting of- VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS.Single trap symphonic W.C. Suite white (HSR 30.5a-i)

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow Black or white plaster seat and lid. White plastic seat (Solid)(HSR 30.13i)

PROVIDING AND FIXING IN POSITION INDIAN MAKE (ORDINARY) LAVATORY SUITES Consisting of Lavatory in VITREOUS CHINAWARE size as given Below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary; R.S or C.I brackets for building into wall including paintings 32 mm C.P BRASS WASTER WITH C.P brass chain and rubber plug; 15 mm C.P BRASS SCREW DOWN PILLAR TAP WITH Jamnuts or couplings best design ( as approved by the Engineer- In-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS FLOORS AND PAINTING OF FITTINGS ETC. white Size 550 mm x 400 mm with one no. tap(HSR 30.41iv)

Providing and fixing in position 15 mm i/d C.P brass bib Cocks of best quality (as required by Engineer-in-charge) Bib cock (HSR 30.75 c)

Providing & fixing PVC Rain water pipe 6 Kg Pressure of ISI Mark in cement mortor during masonery work. (a) 100MM dia PVC pipe 6Kg. Pressure (Note:- Reputed make PVC pipe such as Supreme, Finolex, Prince will be used as approved Engineer in Charge (HSR 13.89a) Note:- The agency to whom the work is allotted will have to produce original bill/ voucher for all quantity in token of proof of purchase of material

Providing & fixing PVC Bend ISI Mark (a) 100MM dia PVC Bend (Note:- Reputed make PVC pipe such as Supreme, Finolex, Prince will be used as approved Engineer in Charge (HSR 13.90a) Note:- The agency to whom the work is allotted will have to produce original bill/ voucher for all quantity in token of proof of purchase of material

CONSTRUCTING BRICK MASONRY INSPECTION CHAMBER SIZES AS GIVEN BELOW UPTO 0.60 METRE AVERAGE DEPTH in cement Mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation Cement mortar 1:2:4 BENCHING 12 mm THICK CEMENT PLASTER 1:2 with a floating coat of 1 mm thick of neat ceement R.C.C 1:2:4 slab 100mm thick CC topping 3.50mm thick with 455x455mmm/ 455610mm indise light duty C.I Inspection chamber cover & frame weight as per ISI specifications painted with 3 coats of black bitumanstic superior paint complete as per standard design (Size 450c450mm inside ( with 455 mm x 455 mm cover and frame light duty single seal weighing 40 kg with C.C. topping )(HSR 29.84a)

Dismantling white or coloured glazed tiles (HSR 8.38)

Dismantling brick or flagged stone slab flooring including Concrete base.(HSR 8.27)

Kotah stone flooring minimum 25mm thick in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing.(HSR 14.62)

Providing and fixing rustic texture paint of required with two or more coats applied @ 3.28 ltr/10sqm) over and including priming coat of exterior primer applied @ 2.20kg/10sqm over two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete (J.K / Birla Make) including scrapping of old white wash/ colour wash complete in all respect as desired by Engineer-in-Charge (N.S). Note the agency to whom the workis allotted will have to produce original / bill voucher for all quantity in token of proof of purchase of material.

Painting two coats with plastic emulsion paint on walls on new work to give an even shade. (HSR 16.30) (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge)

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality 1.0 mm thick(DSR 9.127.2)

Providing and fixing Aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS;733 and IS;1285 fixed with raw plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. aluminum sections shall be smooth, rust free straight mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling C.P brass/stainless steel screws. All complete. Fixed portion (Anodized Aluminum transparent or dyed to required shade according shade according to IS;1868, minimum anodic coating of grade AC 15)(HSR 17.95) Note-1 In Case of any difference in the unit & Nomenclature of any of the HSR/DSR items of Civil & PH work depicated in this DNIT and that given in HSR/DSR, the unit and nomenclature given in HSR/DSR shal lbe applicable . 2. Only reputed make material will be used (Make/ Brand exhibited in HSR/DSR and exhibited in approved standard document) as approved by the Engineer-in-Charge, while exeuting various items/ work at site.

Bharat Singh