WIDENING AND RESURFACING OF ROAD FROM CERTAIN GATE TO CHOWK AT NAMS

Amount

Material and labour prepartion of existing black top surface by brushing for removing caked mud etc sweeping with brooms and finally fanning the cleaned surfae with Air compressor/mechanical brush to remove all loose dirt etc and applying evenly a tack coat with paving bitumen VG-10 grade @ 5 kg per ten sqm by mechanical sprayer, complete all as specified and directed.

M&L laying Bituminous premix asphaltic concrete semi dense carpet 30 mm thick (consolidated thickness) with 5.5% binder content Grade VG-30 rolled and compacted with 8 to 10 tonne power roller to required gradient and camber rolled uniform smooth surface, complete all as specified by using mechanical sensor pavers omplete all as specified and directed. (Note : Premixed carptet shall be done by using machnical mixer as specified in clause 20A 27 of MES SSR Part-I the spreading of premix carpet shall be done by mehanical sensor paver only)

Surface excavation not exc 30cm in depth but averaging in 15cm getting out in soft/loose soil omplete all as specified and directed.

Rolling and consolidating formation surface in cutting with 12 tonne vibrating power roller complete all as specified and directed.

Material and labour for 200mm (spread thickness) soling (or sub base) with broken boulders or quarried sand stone, 63mm to 90mm size, interstices filled, surface formed, rolled with vibromatic/ vibratory roller 8 to 12 tonne and consolidated to required gradient and camber complete all as specified and directed.

Material and labour for 150mm (compacted thickness) water bound macadam in two layers each of 75mm thick (each layer to be rolled and consolidated separately) with coarse aggregate of granite /trap/blast stone of grading 2 ranging from 63mm to 40mm, hollow made up to from true surface, spread, surface binding with and including screenig and moorum, watered, consolidated and rolled with a 8 to 12 tonne vibromatic/vibratory roller to gradient and camber required omplete all as specified and directed.

Prepartion of unsurface water bound macadam by brushing with wire brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surfae with gunny bags to remove all loose dirt etc and applying evenly a tack coat with paving bitumen @ 10 kg per ten sqm by mechanical sprayer omplete all as specified and directed.

Material and labour laying Bituminous premix asphaltic concrete semi dense carpet 40 mm thick (consolidated thickness) with 5.5% binder content Grade VG-30 rolled and compacted with 8 to 10 tonne power roller to required gradient and camber rolled uniform smooth surface, complete all as specified by using mechanical sensor pavers omplete all as specified and directed. (Note : Premixed carptet shall be done by using machnical mixer as specified in clause 20A 27 of MES SSR Part-I the spreading of premix carpet shall be done by mehanical sensor paver only)

Material and labour for making of road side berms Shingle filling in floors or pavings, laid in layers n exc. 15 cm thick, spread,levelled, and blinded with earth and rammed including watering omplete all as specified and directed.

Material and labour continuous brick edging with width equal to the depth of the brick,laid on end vertically complete all as specified and directed.

Preparation of road surface and applying thermoplastic reflective paint in marking of minimum 1.5 to 2mm thick single coat as in center line and edge line road marking of 150/100mm width using 'Hot Mark' thermoplastic modern propelled road marking machine as directed including all ingredients such as blinder glass beads titanium dioxide calcium carbonate inter fillers thermoplastic requirment for glass beads shall be the table No 800.4 of MORTH specification including spraying of glass beads etc all as per manufacture instruction complete all as specified and directed.

Supply and fixing for CAT EYE yellow colour two colour two ways reflective road studs ABS plastic body confirming to IS-67-1977 having road capacity of 40 tonnes of size 100x100x20mm with heavy reflector yellow colour both side complete all as specified and directed. Make : DARK EYE cat part NO 972 P or equivalent makes as specified in list of makes.

Supply and fixing for road solar stud size 125x125x25mm made from aluminium alloy and PC construction, solar powered by monocrystal solar panel alongwith high capacity rechargable battery (led - 10mm, 3 pieces each side and total 6 pieces are used for high brightness) water proof confirming to IS-67-1977 having load capacity of 40 tonnes complete all as specified and directed. Make :- Dark Eye Cat Part No DA-110 (DHRUV) or equivalent of makes specified in list of Makes.

Material and labour for brick work with sub class 'B' bricks in CM (1:6) straight or curved on plan exc 6 m mean radius, complete all as specified and directed.

Material and labour cement plaster 15mm thick in CM 1:4 on Brick/concrete surface etc finished even and fair without using extra cement complete all as specified and directed.

Material and labour reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in slab and finishing exposed surfaces fair & even omplete all as specified and directed.

Material and labour for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Material and labour for form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work, not exceeding 200 mm thick horizontal or sloping, for fair finished surfaces complete all as specified and directed.

Material and labour Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface (Broken atone & boulder) complete all as specified and directed.

Material and labour for 100mm thick PCC 1:4:8 type D2 using 40 mm graded aggregate as in sub floor Complete all as specified and directed.

Material and labour for Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment, confirming to IS 15658-2006of 60mm thickness complete all as specified and as directed.

JAGSON DEVELOPERS (BID ID -3300956)