ADDITION ALTERATION TO TYPE C QTR C-1, C-2 and C-3 BLOCK AND TYPE B QTR B-6, B-7, B-8, B-9 and B-10 BLOCK IN RESIDENTIAL AREA RCI HYDERABAD

Amount

Demolition of plain cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as directed.

Demolition of floor hearth or wall tiling including cement mortar bedding but not backing and removing rubbish off the premises complete all as directed.

Non skid joint free ceramic coloured tiles 7 to 8 mm thick of size 600mm x 600mm set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed of 15 mm thick in CM 1:4 complete all as specified and directed.

Non skid joint free ceramic tiles 7 to 8 mm thick (Square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed of 15 mm thick in CM 1:4 complete all as specified and directed.

Non skid joint free ceramic coloured tiles as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with adjacent tiles over and including 10mm thick backing coat in CM (1:3) complete all as specified and directed.

Glazed ceramic coloured tiles in verticle surface (size not less than 300 x 450mm) x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match with adjacent tiles over and including 10mm thick backing coat in CM (1:3) complete all as specified and directed.

18mm to 20mm thick granite stone (of any type) work (table rubbed and polished) in cooking platforms and in window cills and like over and including 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite, complete all as specified and directed.

Machine cut kota stone slab flooring 20-25mm thick laid over and including cement mortar screed bed 20 mm thick in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

20-25mm thick Kota stone single piece of length 0.90m to 1.00m in treads and riser of steps, skirting, dado and pillar laid over and including 15mm cement mortar screed bed in CM (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Moulding half round to edges of stone slabs one edge, 20mm thick in steps, cooking platform and other similar situations, complete all as specified and directed.

Demolition of brick/stone masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius, builtin CM (1:6) complete all as specified and directed.

Brick work wih sub class `B' bricks, straight or curved on plan to any radius in half brick thick wall, built in CM (1:4) complete all as specified and directed.

Taking down cement plaster or brick or stone walls / concrete surfaces including taking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Rendering 10 mm thick in CM (1:6) on fair faces of brick walls and surface finished even and fair without using extra cement complete all as specified and directed.

Rendering 5 mm thick in CM (1:3) on fair faces of concrete surfaces on ceilings, finished even and smooth without using extra cement complete all as specified and directed.

Rendering 15 mm thick in two layers with 5mm thick in cement mortar (1:4) as setting coat over 10mm thick cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement using water proofing compound (in top layer), as per manufactures instructions, complete all as specified and directed. Note: Water proofing compound shall be measured and paid seperately as supply only.

Supply only integral water proofing compound, complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in kerbs, copings, bed plates, bases of tank padding concrete etc. complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floor aprons, slabs and shelves etc laid and bedded in cement mortar complete all as specified and directed.

Taking down chowkats or frames (without taking off shutters from the frames) n.exc 1.50 Sqm each, complete all as specified and directed.

Taking down chowkats or frames (without taking off shutters from the frames) exc 1.50 Sqm and n. exc 4.00 Sqm each, complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm and n.exc 2 sqm each, complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm and n.exc 2 sqm each and refixing in the same opening complete all as specified and directed.

Pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening complete all as specified and directed.

35mm thick 2nd class hard wood Guazed and skeleton shutters, open rebated and prepared to receive glass, guaze etc., (without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc; sizes of members of shutters as specified in SSR PArt-I, Section 8, Clause 8.24(a), supplied and fitted to chowkats and directed.

Stainless steel wire cloth 1.4mm nominal dia of wire and 12mm of size of mesh fitted with tinned tacks or stainless steel with staples complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed.

19mm thick block boards with mica laminated exterior grade, commercial type, fixed with screws to timber frame-work as in shelves, complete all as specified and directed.

19mm thick prelaminated particle board exterior grade, prelaminated with one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

35mm thick flush shutters solid core construction with particle board core and plywood face panels commercial type on both sides complete all as specified and directed.

2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

Treating small articles such as hold fast area n. exc 0.1 each with black tar or coal tar black paint complete all as specified and directed.

Plain cement concrete 1:3:6 type C-0 using 12.5mm graded stone aggregate, filling in the back portion of pressed steel door frames complete all as specified and directed.

Aluminium butt hinges 100mm long, fixed with mild steel hinge pin, anodised type C-21 complete all as specified and directed.

Aluminium butt hinges 75mm long, fixed with mild steel hinge pin, anodised type C-21 complete all as specified and directed.

Aluminium alloy anodised sliding bolt 300 mm long with hasp, staple (bolt type) and fixing of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed.

Aluminium anodised barrel tower bolts 200 mm long, extruded section and fixed complete all as specified and directed.

Aluminium anodised barrel tower bolts 100 mm long, extruded section and fixed complete all as specified and directed.

Aluminium alloy anodised handle of size 250 mm, fabricated type complete all as specified and directed.

Extruded aluminium alloy anodised handle of size 150 mm fabricated type complete all as specified and directed.

Magic eye brass body fixed in position, complete all as specified and directed.

Cutting holes into or through brick / stone masonry built in cement mortar depth exc half brick but not exc one brick complete all as specified and directed.

MS flat iron 25 x 3mm thick of 250mm length hold fasts for fixing chowkats complete all as specified and directed.

Hasp and staple 125mm size, safety type, aluminum anodised including bolt to hinge plate, fixed in repairs with screws complete all as specified and directed.

Aluminium alloy floor door stopper 150mm length of aluminium body and tongue anodised with hard drawn steel spring, fixed in floor complete all as specified and directed.

Ball catches with 8mm dia steel ball, brass body and stiking plate including letting in and fixed, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for as in steel windows and ventilators all as specified and directed.

Powder coated aluminium frame for windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Powder coated aluminium window shutters side hung type without sash bar aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, fittings such as peg stays, hinges, handles, etc and to receive 5mm thick sheet glass complete all as specified and directed. Note: Sheet glass 5mm thick will be measured and paid separately.

Powder coated aluminium ventilator shutters fixed type of any colour without sash bar aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. to receive 5mm thick sheet glass complete all as specified and directed. Note: Sheet glass 5mm thick will be measured and paid separately.

Powder coated aluminum grill type DG 916, TD No. TD/462/2018 Sheet No. 1/1 of approved quality and design complete all as specified and as directed by GE.

Sheet glass tinted 5mm thick, ordinary quality fixed in window frames all as specified and as directed.

Figured glass 3.00 mm thick, pin headed type fixed in ventilators all as specified and as directed.

Supply and fixed in repairs curtain rails of stainless steel 20mm dia with fixing brackets, stops, rollers etc, complete all as specified and directed.

Taking down steel tubing 15 mm and connections including removal from site complete all as specified and directed.

Ditto-all as per Sl item No. 58 above but 20 mm dia pipe.

Ditto-all as per Sl item No. 58 above but 25 to 32 dia pipe.

Galvanised iron tubing 15 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors complete all as specified and directed.

Ditto-all as per Sl item No. 61 above, but bore of pipe 20 mm.

Ditto-all as per Sl item No. 61 above, but bore of pipe 25 mm.

Cutting chases in brick walls for concealed water tubing and making good in CM (1:3) cutting n.exc 10 cm girth complete all as specified and directed.

Dismantling of asbestos cement / PVC SWR pipes of any size or description with cement joints fixed to wall including all fittings complete all as specified and directed.

PVC (SWR) pipes 110 mm single socketed in any length, with rubber ring joints fixed to walls complete all as specified and directed.

PVC (SWR) bends / shoes 110 mm dia complete all as specified and directed.

Stack clamps for 110mm dia pipes of any description of 50x5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

Dismantling of cast iron soil pipes jointed in cement mortar up to and including 100 mm dia complete all as specified and directed.

PVC soil, waste and vent pipes, sand cast pipe 75 mm dia, in any length with or without ears with lead joints fixed in walls complete all as specified and directed.

Ditto-all as per Sl item No. 70 above, but 100 mm dia pipe.

Supply and fixed in repairs PVC bend (any radius) 75 mm dia, diminishing pieces or tapers with access door complete all as specified and directed.

Ditto-all as per Sl item No. 72 above, but 100 mm dia.

Supply and fixed in repairs PVC branch pieces, 75 mm dia single or double, ordinary or inverted (equal or unequal) or with paralell branches fitted with access doors complete all as specified and directed.

Ditto-all as per Sl item No. 74 above, but 100 mm dia.

PVC vent cowl 75 mm dia, fixed in repairs, complete all as specified and directed.

PVC vent cowl 100 mm dia, fixed in repairs, complete all as specified and directed.

Rotational moulded polythelene triple layer water storage tanks (cylinderical, vertical with closed top) hoisted and fixed in position 500 ltr capacity including dismantling of old tank of any description (PVC / RCC / Hume pipe) and removing to MES store.

Supply and fixed in repairs sink with drainage board made of stainless steel 1mm thick kitchen or laboratary with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilver brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Stainless steel plate rack of size 900 x 900mm, 1mm thick including fixing to wall / concrete surfaces as per manufacturers instructions complete fixed in repairs all as specified.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for, such as sunken floor filling etc, complete all as specified and directed and removing off site.

Providing water proofing treatment to bottom and sides of sunken floor area not exc 3.50 Sqm with Acrylic based polymer modified cementious composite compound as specified and approved in two layers, In 1st layer @ 0.4888kg cement mixed with 0.253kg composite compound per sqm and allow to dry for 4 Hours, then apply 2nd layer @ 0.242 kg cement mixed with 0.126 Kg composite compound and laying 200 micron polythelene film with approved adhesive and testing including fitting of 32mm GI spout pipe complete all as specified and directed.

PVC floor trap 75mm dia outlet with grating including jointing to waste pipe fixed in cement concrete type B-1, 1:2:4 diameter of out let pipe 100mm fixed in repair.

PVC Nahani trap 75mm dia outlet with grating including jointing to waste pipe fixed in cement concrete type B-1, 1:2:4 diameter of out let pipe 100mm fixed in repair.

Chromium plated brass Bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and directed.

15mm dia Brass chromium plated mixer for mixing hot & cold water screwed down for iron pipe in Bathrooms fixed all as specified and directed.

Chromium plated brass stop valves 15 mm dia, fancy type with long shank and cup (concealed type).

Chromium plated brass Angle valves 15 mm dia high pressure screwed for iron pipe and fixed, all as specified and as directed.

20mm dia Gun metal globe or gate valves with iron wheel head screwed both ends, for iron pipe complete.

PVC ball valves 20 mm dia high pressure with polythene float and flynut screwed for iron pipe or brass ferrule complete.

Towel Ring of CP Brass fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 90gms) complete.

Vitreous china white squatting pan orrissa pattern size 630x450mm with integral foot rest including provision of lime concrete bedding complete fixed in repairs.

PVC Flushing cistern 10 Ltr capacity of duel flush type approved make and colour with complete all as directed fixing in repairs.

Supply and fixed in repairs Wash hand basin white vitreous china 550 x 400mm including brackets and cutting for pinning in ends of brackets or erecting stand all as specified and directed.

Supply and fixed in repairs PVC connection 15 mm dia 600 mm long with PTMT nuts at both ends all as directed.

Supply and fixed in repairs PVC waste pipe 32mm dia of length 750mm long for wash hand basin / sink, complete all as specified and directed.

Supply and fixed in repairs PTMT soap rack / Niche fixed with and including chromium plated brass screws and wooden / plastic cleats complete all as specified and directed.

Supply and fixed in repairs stainless steel peg set of 3 hooks of any type all as specified and directed.

Supply and fixed in repairs CP Brass towel rail 600 mm long fixed with and including chromium plated brass screws and wooden / plastic cleats complete all as specified and directed.

Chromium plated brass shower rose 125 mm size including shower arm of size 250 mm long with flange fixed in repairs.

Taking down existing roof treatment of any description including cement plaster on concrete surface of roof slab including cleaning by picking sweeping and washing down with water to remove dust complete all as specified and directed.

10mm thick cement plaster in CM 1:4 mixed with water proofing compound (after applying cement slurry @ 3 Kg/Sqm over the existing roof slab) and surface finished even and smooth complete all as specified and directed. Note: (a) The rate quoted shall be deemed to inclusive of cost of cement slurry. (b) WPC will be measured and paid seperately.

M&L, APP based polymeric membrane weighing minimum 3.5Kg/Sqm and minimum 3mm thick, reinforced with polyester non woven fabric (weight not less than 160 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied at a rate of 0.3litre/Sqm by forced application, complete all as specified and directed. Note: The treatment shall be got executed through specialist agency or under their supervision and guidance.

20mm thick hydraulically pressed cement concrete tiles of size 300 x 300mm laid over including 15mm thick cement mortar screed 1:6 mixed with water proofing compound and jointed with CM (1:3) mixed with 5% crude oil by weight of cement over APP Membrane complete all as specified and directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizantal faces of grooves with cement mortar in CM 1:3 and making good in CM 1:3 after inserting membrance in to the groove complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for.

Reinforced cement concrete type B-1 1:2:4 (using 20mm graded stone aggregate) as in slabs supported on walls, deck slabs and in shelves and the like complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends etc binding with MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Ditto-all as per Sl item No. 109 above, but Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC / PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer over a coat of putty finish all as specified and directed.

Preparation of newly plastered surfaces of ceiling and applying two coats of distemper oil emulsion over a coat of alkali resistant primer all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of exterior weather proof paint (Apex Ultima of M/s Asian Paints / weather coat smooth of M/s Berger paint / weahter max exterior acrylic of M/s ICI Dulux) over a coat of primer over one coat of putty finish and as per manufacturer's instructions, complete all as specified and directed.

Complete removal of existing treatment from surfaces of walls and applying two coats of exterior weather proof paint (Apex Ultima of M/s Asian Paints / weather coat smooth of M/s Berger paint / weahter max exterior acrylic of M/s ICI Dulux) over a coat of primer and as per manufacturer's instructions, complete all as specified and directed.

Preparation of old treated surfaces by washing, rubbing down and stopping of distempered and painted surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer over a coat of putty finish all as directed.

Ditto-all as per Sl item No. 116 above, but on ceilings.

Preparing surface of new wood & steel of any description not otherwise described and treated with tar or coal tar black paint complete all as specified and directed.

Preparation of new wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of old steel surfaces of any description, not otherwise described and applying one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed.

Preparation of new iron / steel surfaces of any description, not otherwise described and applying two coats of first qualtiy synthetic enamel paint over a coat of primer, complete all as specified and directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron of the vertical surface of the sub-structure to a depth of 300mm complete all as specified and directed by Engr-in-charge.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as speicified and as directed.

75mm thick plain cement concrete type B-1, 1:2:4 (20mm graded aggregate) laid as in Plinth Protection complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep ang getting out in hard / dence soil, complete all as specified and directed.

Hardcore of guage n.exc 63mm deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) 100mm thick as in floors finished even and smooth without using extra cement, complete all as specified and directed.

Plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) 75mm thick as in floors, complete all as specified and directed.

Cement concrete chequerd tiles 300mm x 300mm x 25mm thick set jointed and pointed in neat cement slurry with grey cement and pigment in floors including laying over and including 15mm thick cement screed bed in CM (1:4) complete.

Framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete.

Cutting salt-glazed stone ware drain pipe of 150mm dia in position, including jointing socket end of new pipe to same with packed spun yarn and cement mortar 1:1 complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for anf forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-I smooth finished and reforming benching as required, complete all as specified and directed.

Ditto-all as per Sl item No. 132 above, but removing existing branch drain, making good to walling and rendering cutting out branch channel and making good benchings etc complete.

Setting in CM 1:3 and haunching with cement concrete 1:2:4 type B-1 around cast iron manhole covers and frames medium duty of any type and size, complete all as specified and directed.

Demolition / breaking up drain pipes (Salt glazed stone ware) 150mm bore, jointed in cement mortar of any description, complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n,exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, man holes, pier holes, etc n.exc 10 sqm on plan and getting out in hard / dense soil, all as speified and directed.

Salt glazed stone ware drain pipes grade A, 150mm bore laid in trenches and jointed in cement mortar (1:1) including testing after the pipes are laid complete all as specified and as directed.

Plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in concrete bed to drain pipes 150mm bore including packing under and haunching against the sides of pipes after thay are laid and tested complete all as specified and directed.

Extra for forming fair finished drain or channel of 30cm inner girth in cement concrete, using cement including forms moulds mitred/ Stopped ends etc complete all as speicified and as directed.

Removing excavated materials not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Taking down aluminium point wring (light, fan, socket or power) complete, including fixture and fitting such as switches, ceiling roses, pendants regulaotr, socket, light fitting etc, and removing and making good disturbed surface of walls, floors, etcto matches with the existing, including separating serviceble fittings / fixtures, socket / switches fittings complete all as directed.

Point wiring complete with 1.5 Sq.mmm PVC insulation unsheathed multi-starnded FRLS copper conductor 1100 Volts grade draw through in and including 20 mm dia PVC conduit and conduit accessories, concealed in walls including making necessary chases in walls and making good to match with existing surface and terminated to and including provision of modular metal flush boxes (metal switch board of any type and size) with modular metal frame plate and white cover for housing switch, sockets, regulators etc, including 1.5 sqmm PVC insulated unsheathed multi-stranded FRLS copper conductor cable as earth continuity conductor and connecting to common earth dolly, complete all as specified and directed for one 5 amps one way modular switch for one light point, complete all as specified and directed. NOTE: The cost of metal flush boxes, modular white cover plate deemed to include under respective items of this Schedule.

All as per SI item No. 143 here-in-before, but for one fan point controlled by one 5 Amps one-way modular switch.

All as per SI item No. 143 here-in-before, but for one Exhaust fan point controlled by one 5 Amps one-way modular switch.

All as per SI item No. 143 here-in-before, but for one Bell point controlled by one 5 Amps one-way modular switch.

All as per SI item No. 143 here-in-before, but for One light point controlled by two 2-way switches.

All as per SI Item No. 143 here-in-before, but for one 3 pin socket out let 6 amps modular socket controlled by one way switch on same board.

All as per SI Item No. 143 here-in-before, but for one 3 pin socket out let 6 amps modular socket controlled by one way switch on independent board.

All as per SI Item No. 143 here-in-before, but for 15 amps socket outlet with 2.5 Sq.mm copper cable including 2.5 Sq.mm PVC insulated copper conductor cable as earth continuity conductor and connecting to earth dolly, complete all as specified and as directed.

LED light fitting 9 W, 230v, complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as specified and directed. Cat No. Havells Cat No-LUMILINEBS9WLED865SPCWH of Havells or Equivalent in Wipro / Philips.

LED retrofit lamps B-22 9 watt holder base with polycarbonate body and aluminium heat sink. Make: HAVELLS or equivalent model of Bajaj / Crompton.

Sub main wiring complete with 2 runs of 2.5 sq.mm PVC insulated and unsheathead 1100V grade FRLS multistranded copper conductor and drawn through in and including PVC conduit of medium grade and conduit accessaries of suitable size concealed in walls with, necessary civil works for making good disturbed surface, and / or laid on surfaces over ceilings / columns etc and connecting terminal ends to meters and DB's including 1 run of 2.5 Sq.mm insulated multistranded FRLS copper cable as earth continuity conductor and connecting to common earth dolly, complete including removing old sub main wiring all as specified and directed. Note: (i) Two runs of 2.5 Sq.mm copper conductor, one run of 2.5 sq.mm copper earth continuity conductor and one run of suitable size of PVC rigid conduit and required conduit accessaries shall be measured as one unit length. (ii) Extra length of cable / wire required for connection to MCBs shall not be measured and the measured and the rate quoted per unit shall deemed to be inclusive of the same acordingly. (FOR AC WIRING & BUILDING SECURITY LIGHT WIRING)

Modular switch one way 6 Amp, one module 240V, single pole complete all as specified and directed.

Modular switch 2 way 6 Amp, one module 240V, single pole complete all as specified and directed.

Modular switch one way 16 Amp, one module 240V, single pole complete all as specified and directed.

Bell push modular type, 5 Amps button all as specified and directed.

Modular Socket, 6A - 2/3 pin combination 2 module, complete all as specified and directed.

Modular Socket, 6A/16A - 2/3 pin (5 pin) combination 2 module, complete all as specified and directed.

Ceiling rose two to three terminal surface backelite type AC 50 HZ 230 Volt, complete all as specified and directed.

Bracket light fitting made up of poly carbonate suitable for fixing LED bulb of 9 Watts of base B-22 all as specified and directed. Cat Part No: LHDL03160099 of Havells or equivalent in Wipro / Philips.

LED tube light fitting 20 W, 230v regal batten type, single side connection included with 20 watt LED tube rod single side connection complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as specified and directed. Cat No. Havells Cat No- PHOTONULTRAE2.01213T8SSTL20WLED865SPC for Tube rod, Batten Cat No. REGALBATTENT8UPT01X22WSSBSWH Make: Havells or equivalent in Wipro / Philips.

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized earth lead wire 4mm dia by means of galvanized iron or steel bolts, nuts, check nuts and washers, and connected to equipments as directed, including funnel with GI medium grade watering pipe 20mm bore, wire mesh, charcoal or coke and common salt in alternate layers of 15cm compacted thickness all around the earth electrode, with concrete pit in PCC 1:3:6 type C-1, 50mm thick precast RCC 1:2:4 type B-1 cover slab reinforced with 8mm dia deformed bar 15 cm C/C and suitable handle of 10mm dia round bar, GI light grade pipe 15mm dia for earth lead protection including necessary excavation earth work in soft / loose soil and disposal of spoil to a distance n.exc. 50m and necessary testing complete all as shown on electrical plate No. 3 of MES SSR Part-I and as directed. Note: After completion of testing of earthing the following details should be painted in earth pit cover (a) Earth pit No. (b) Date of measurement. (c) Due date.

Taking down KWH and keep in safe custody and refixing the same as including necessary electric connection from main to KWH meter and KWH meter to out going distribution board complete all as specified and directed.

Painting of ceiling fans complete in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc complete all as specifeid and direcetd.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades and keep in safe custody and refixing the same at site complete all as specified and directed by Engineer-in-Charge.

Metallic exhaust fan 230 mm sweep light duty, AC single phase, 230 / 240 volts including louvers and shutter with complete accessories complete all as specified and directed by Engineer-in-Charge.

Modular type electronic fan regulator 120 watts, 230 volts, 50 Hz two modules complete all as specified and directed.

Bell electric 230 Volts ding dong type complete all as specified and directed by Engineer-in-Charge.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one MCB SP 20 Amp ‘C’ curve capacity complete all as specified and directed.

Energy saving IP 66 protection LED street light fitting 45 watt 230V single phase AC supply luminaries made up of pressure die cast aluminium housing with high power LED as lightning source and lens embedded PC cover having top opening separate compartment for driver including connecting up with twin core flexible copper conductor cable and complete accessories complete all as specified and directed. Make: Havells Cat No. ENDURA PEARL NEOSL45WLED 757PASTTOPC OR equivalent in Wipro / Philips.

Replacement of unserviceable GI pipe bracket for street light fitting made from 40 mm dia light grade 1500 mm long bend to shape welding etc and fixing on LT pole with 50x6 mm flat iron MS clamp and necessary nuts, bolts, and washers complete, all as specified and as directed by Engineer-in-Charge.

Sheet metal enclosure single door for MCB DB's phosphatised powder painted with bus bar 200 Amps rated single pole and neutral link of 8 way 240 Volts AC complete all as specified and directed by Engineer-in-Charge.

Replacement of unserviceable MCCB TPN 200 Amps capacity 25 KA, 240 Volts, 50 Hz complete all as specified and directed by Engineer-in-Charge.

MCB SPN 40 to 63Amps, 10 KA, 240 Volts complete all as specified and directed.

MCB single pole (SP) 06 to 32Amps, 240 Volts, 240 volts, 'B' curve, 10 KA complete all as specified and directed.

Sub main wiring complete with 2 runs of 6.0 sq.mm PVC insulated and unsheathead 1100V grade FRLS multistranded copper conductor and drawn through in and including PVC conduit of medium grade and conduit accessories of suitable size concealed in walls with, necessary civil works for making good distrubed surface, and / or laid on surfaces over ceilings / columns etc and connecting terminal ends to meters and DB's including 1 run of 6.0 Sq.mm insulated multistanded FRLS copper cable as earth continuity conductor and connecting to common earth dolly, complete including removing old sub main wiring complete all as specified and directed. Note: (i) Two runs of 6.0 Sq.mm copper conductor, one run of 6.0 sq.mm copper earth continuity conductors and one run of suitable size of PVC rigid conduit and required conduit accessories shall be measured as one unit length. (ii) Extra length of cable / wire required for connection to MCBs shall not be measured and the measured and the rate quoted per unit shall deemed to be inclusive of the same.

Maruthi international

M/S GDR CONSTRUCTIONS

SHAH ENTERPRISES

Shetty Construction Co

c devender reddy and co