REPAIR TO ROAD, POTHOLES , ROAD SIDE BERMS AND ROAD FURNITURE AT AEC COLLEGE AND CENTER PACHMARHI UNDER AGE(I) PACHMARHI

Amount

M&L for repair to potholes any depth, not exc 1.0Sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25mm in depth, making good by applying evenly a priming/ tack coat of bituminous primer with paving bitumen VG-30 @ 5 Kg/ 10Sqm, putting in premixed bituminous macadam, well rammed and sealed with binder i.e. paving bitumen VG-30 @ 9.80Kg/ 10Sqm, blinded with 0.09 Cum of stone chippings of 6.3mm size and again well rammed (including supply of premixed macadam, binder and chippings) depth of pot holes exc 30mm complete all as specified and directed.

Preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and directed.

M&L for appling evenly a priming / tack coat at bituminous primer with paving bitumen VG-30 @ 5kg/10 sqm by using mechenical sprayer on black top surface of road complete all as specified.

M&L for bituminous premixed asphaltic semi dense concrete 30 mm consolidated thickenss with minimum 5.5% binder content using paving bitumen VG-30 by weight of total mix, rolled and compected to requried camber and gradient using 8 to 12 tonne tandem vibrator roller complete all as specified and directed. Notes:- (i) Bituminous premixed asphaltic semi dense concrete shall be prepared in hot mix plant only. (ii). Bituminous premixed asphaltic semi dense concrete shall be laid with sensor paver only. (iii) Binder content shall be tested at site as directed.

M&L for providing and laying 25 mm thick Mastic Asphalt Wearing Course conforming to IS-5317:2000 and IS-1195:1978 with 14% binder content by weight of total mix,prepared by using Mastic Cooker with Paving Grade Bitumen and using filler material as Lime Stone Powder, laid at required slope in panels of 1m width and providing anti-skid surface with Bitumen Pre-Coated Fine-Grained Hard Stone Chipping of 20 mm nominal size as directed at the rate of 0.005 Cum per 10SQM at an approximate spacing of 100 mm C/C in both directions pressed into surface when the temperature of surface is not less than 100°C, protruding 2 mm to 5 mm over mastic surface as per Clause 515 of MORTH, consolidated with 8 to 10 tonne power road roller to required level gradient, camber and super-elevation complete all as specified and directed.

M&L for premixed bituminous macadam for consolidated thickness upto 75 mm or less with using 19 mm graded (Grading 2) stone aggregate with minimum 4.0% binder content using paving bitumen VG-30 by weight of total mix, rolled and compacted to required camber and gradient using 8 to 12 tonne tandem vibratory roller complete all as specified and directed. Notes:- (i) Premixed bituminous macadam shall be prepared in hot mix plant only. (ii) Premixed bituminous macadam shall be laid with sensor paver only. (iii) Binder content shall be tested at site as directed by Engr-in-Charge.

M&L for appling evenly a priming / tack coat at bituminous primer with paving bitumen VG-30 @ 10 kg /10 Sqm by using mechenical sprayer on black top surface of road complete all as specified.

Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exc 400Sqm and depth n exc 50mm , by using mechanical scarifier including racking over and grading the broken-up surfaces to the proper camber or removing to a distance not exc 50M from the starting point and stacking complete all as directed.

M&L for preparation of existing bituminous road surfaces by removing dust, dirt, grease and other foreign matters etc and after prepration of road surfaces, applying road marking having minimum 2.5mm average thickness with & including thermo plastic (Reflective) line marker paint/ compound of uniform surface finish conforming to BS 3262 (Part-I) 1989 read in conjunction with the MORTH specification 803 clause 4.2.2 on bituminous surfaces in white/ yellow colour and super imposed with glass beads conforming to BS 6088 read in conjuction with the MOST specification 803 clause 4.3.3 complete all as specified and directed. Notes:- (i) MORTH specification 803 shall be followed strictly for execution of work & suitable machine shall be used for the marking as approved by AGE(I). (ii) Shape, size & pattern of marking shall be as approved by AGE(I).

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cm in thickness (below or above ground level) including removal of debris to out side MD land complete all as specified & directed.

M&L for PCC( 1:2:4) Type-B1, using 20 mm graded stone aggregate in coping including necessary formwork complete all as specified and directed.

M&L for 100 mm thick PCC(1:4:8), Type D2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

Dismantling stone slab and tiles of any description or any thikness, laid dry in floors, apron etc. complete all as specified and directed

M&L for 80 mm thick rubber mould reflective factory made coloured pre cast PCC interlocking paver blocks conforming to IS 15658-2006, M-40 grade of concrete, shape and size as approved by AGE, in hard standing, laid dry over & including 50 mm thick sand cushion and filling the voids of paver blocks with dry sand complete all as specified & directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the requried line, level and curvature , jointed with cement motar 1:3 (1 cement : 3 coarse sand ) including making joint with or without groove ( thickness of joint except at sharp curve shall not to more than 5 mm ) including making drainage opening wherever required complete all as specified & directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with fly ash brick straight or curved on plan exc 6m mean radious built in cement motar (1:6) complete all as specified.

M&L for rendering 10 mm thick on other than fair face of brick work or concrete surface in cement motar 1:4 complete all as specified and directed.

Supply and fix, in repairs, cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector fixed with and including MS stud of suitable size as per Manufacturer's instructions and to be fixed with Epoxy- Resin based adhesive or Special Hot Melt Bitumen adhesive avoiding nails etc complete all as specified and directed.

Supply and fix, in repair, solar cat's eye/ studs of size 125mmx 125mmx 25mm (shank 60mm) with aluminium alloy shell, high efficiency Mono-Crystalline Solar Panel 2.40V/ 0.30 Watt having one Ni-Mh or NI-cd rechargable battery (1.2V/ 1600mA), Six Super Bright LEDs with 10,000 to 18,000 mcd (Millicandela) having flash rate 2 Hz and bearable weight 10 tons approx with view distance upto 1000 meters of any colour i.e yellow, red, blue, green or white as required at site, working temp 10-75 degree Celcius, working time 3 to 4 days after fully charged battery, charging time 5 to 6 hours from direct sun light, maintenance free, un-breakable poly carbonate clear facing, automatically turns on at night and turns off at dawn including all fixing arrangment as per manufactures instructions complete all as specified and directed.

S&F, in repair, dual-directional speed-breaker having high intensity cube corner reflector ultrasonic welded to high impact resistant ABS plastic body of colour yellow and black of size 250X345X50MM provided with 4 steel nails, shape of side body to have interlocking pattern to keep all speed breaker in a row complete all as specified and directed .

Supply & Fix, in repair, 100% water proof metal tubular solar delineator (as per IRC 79-1981) made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC (1:2:4) (150x150x300mm) type B-1 using 20mm graded crushed stone aggregate complete all as specified and directed.

Schedule of credit amount of Rs 17,050.00 to be deducted during AOC

SATHI ENTERPRISES (BID ID -3388648)