PROVN OF TOILET AND ASSOCIATED WORKS FOR QRT AND OTHER SECURITY STAFF ON DUTY AT MAIN GATE AT AF STN MEMAURA

Amount

M&L for excavation over areas, n exc 1.5m deep and getting out in soft/loose soil complete as specified and directed

M&L for Cement Concrete PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) in foundation, filling and mass concrete

M&L for ATT treating the backfill in contact with the foundation at the rate of 7.5Litre of emulsion per square metres of surface area.

M&L for ATT treating the top surafe of fiiled earth at the rate of 5Litre of emulsion per square metres of surface area.

M&L for Form work to sides fo concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter.

M&L for form work to sides of pillars, posts, struts, piers, coloumns and stanchions

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc, also splays between floors and beams, etc complete all as specified and directed

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, loandings and similar work; not exceeding 200mm thick (Horizontal or sloping)all as specified and directed

M&L for RCC M-25 (Nominal mix) in foundations, including rafts, footings, foundation beams, plinth beams; bases for coloumns, etc; basement slabs, under-reamed piles and mass concrete all as specified and directed

M&L for RCC M-25 (Nominal mix) in Columns, pillars, piers, posts and struts all as specified and directed

M&L for RCC M-25 (Nominal mix) in beams, cantilevers, bressurmmers, lintels over 1.5m span

M&L for RCC M-25 (Nominal mix) in Chajjas all as specified and directed

M&L for RCC M-25 (Nominal mix) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck lsabs and in shelves and the like all as specified and directed

M&L for mild deformed TMT steel bars 10mm dia and over, cut to lenght, bent to hsape required, including crandking, bending spirally for hooping fro columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and directed

Ditto, above but 5mm and over upto and including 10mm dia in stirrups, spacers and binders

M&L for hardcore broken bricks of gauge n exc 63mm, deposited, spread and lvelled in layers n. exc 15cm thick watered and rammed to a true surface

M&Lfor PCC type D-2, 1:4:8 (40mm graded aggregate) 100mm thick in sub floors, sub bases floors as specified and directed

M&Lfor PCC type B-1(20mm graded aggregate) 25mm thick in sub floors, sub bases floors as specified and directed

M&L for returning,filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm complete as specified and directed.

M&L for removing excavated meterial n.exc . 50m and deposinting where directed at a level n ecxc 1.5 m above the starting point

M&L Brick work with flyash brick old size, straight or curved on plan exc 6 mtrs mean radius and built in cement mortar 1:4 all as specified.

All as per ser item No. 21 above but half brick wall built in cement mortar 1:4 complete all as specified and directed.

Material & labour for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in CM (1:6) surfaces finished even and fair faces without using extra cement complete all as specified and directed.

M/L 15mm thick rendering in CM 1:4 with with water proofing compound on fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified & directed.(Note- WPC Qty should be measured and paid to separately.)

Supply only water proofing compound complete all as specified and directed.

Material & labour for rendering 10mm thick in cm 1:4 as in ceiling finished even & fair faces complete all as specified and directed .

M/L for roof treatment with polymeric water proofing membrane with certain specification given below as under complete all as specified & directed) (a) Cleaning and brooming the surface of roof. (b) Providing average 15mm thick plaster bed in CM(1:3) mixed with water proofing compound. (c) After the concrete is fully dried. It shall be cleaned free from dust and shall be painted with a coat of bituminous primer @ 0.40 liters/Sqm. (d) After primer, the entire roof surface shall be applied with hot blown bitumen grade 85/25 conforming to IS-702 @ 1.2 Kg/Sqm (e) Over hot bitumen, polymeric water proofing membrane consisting of 90 to 100 micron thick central core of HMHDPE film with standard weight not less than 3 Kg/Sqm shall be laid with 100mm side lap/end lap on prepared surfaces as of manufacture’s technical representation. prepared surfaces and fusing the joints with blow torch application. (f) A coat of bitumen grade 85/25 shall be applied @ 0.30 Kg/Sqm. (g)applying a tack coat of hot blown bitumen grade 85/25 @ 0.3 Kg/Sqm. (h) Apply one coat of aluminium paint (0.2kg/sqm).

M & L for prepration of new plastered or unplastered surfaces of wall applying two coats of oil bound distemper over 1.5mm thick putty complete all as specified and directed.

M&L preparing of new plastered surface of walls and applying two coats of cement base paint over cement primer complete all as specified and directed.

Material & labour for preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed .

M&L for applying two coats of exterior emulsion paint white or tint on walls/ chajja/ facias/ fins on old surfaces including complete removal of existing treatment complete all as specified and directed

S&F non-skid joint free ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.06 Sqm but n exc 0.11 sqm set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor over and including 15mm thick rendering in CM 1:6 complete all as specified and as directed.

M & L galzed ceramic coloured joint free tiles 450 x 350 x 6 to 7 mm/ 450x300x6 to 7mm thick on walls etc set & jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces including 10mm thick rendering in CM 1:4 complete all as specified and as directed. etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-2, (using 40mm graded stone aggregate) as in plinth protection/ path laid in alternate panels 75mm thick finished even and smooth w/o using extra cement.

S&F factory made solid PVC door frames of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of M S tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain coloured PCV ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cementsuppling & fixing in the frame at site as per specification & drawings.

S & F Butt hinges 100mm, extruded aluminium alloy with galvanized mild steel hinge pin, anodised of type B-22 and complete all as specified and as directed.

S&F 200mm aluminium anodised barrel tower bolts of extruded section all as specified

S& F 125 mm extruded aluminum alloy handles, fabricated type anodised.

S&F Powder coated aluminium frame and shutter (minimum thickness of powder coating 50 micron) work for doors, windows ventilators and partitions (Fixed portions) with extruded built up standard tubular section of size 44.45mmx47.62mmx 1.88 mm thick and weight 0.943 Kg/Rm of approved make conforming to IS 733 and 15:1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at i.e junctions, Le at top, bottom. and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight. mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief.

S & F 3mm thick sheet glass ground or Obscured or frosted on one side sheet glass and glazing with oil putty in square nexc. 0.5 sqm in each pane all as specified

Supply & fixing of vitreous china squatting pan ‘Orrisa pattern’ size 580 x 440 mm white with integral foot rest including replacement of ‘P’ or ‘S’ trap lime concrete bedding and making good floor complete all as specified and directed.

Supply and fixing of PVC low level flushing cistern 10 Ltr capacity dual flushing white with inlet , ball valve, float and handle incl brackets incl 32 mm dia PVC flush pipe for low level cistern fixed as in repair complete all as specified and dircted.

Supply & fixing of vitreous china wash hand basin, white size 450x325 mm including brackets, CP waste coupling &PVC waste pipe of 32 mm dia complete all as specified and directed.

S&F PVC Connection 15mm size with PTMT nut of length 300 mm complete all as specified.

S&F 1000 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I incl dismantling of water tanks complete all as specified and directed

Cutting Chases for concealed water tubing etc and making good disturbed surfaces, cutting not exceeding 10 cm girth, on brick walls complete all as specified & directed.

Supply & laying of CPVC pipes SDR13.5 pipes & plain CPVC SDR 11 fittings in floors/walls/ceilingss for 16 mm bore complete all as specified and directed .

All as per item No. 49 above but 20 mm bore pipe.

Supply & fix 20 mm dia ball CPVC valves, high pressure with polythene float and fly nut complete, screwed for CPVC pipe complete all as specified and directed .

S&F in repair 15 mm dia CPVC gate valves with plastic wheel head screwed both ends for CPVC pipe complete all as specified & directed.

S&F in repair 20 mm dia CPVC gate valves with plastic wheel head screwed both ends for CPVC pipe complete all as specified & directed.

Supply & fix in repair long body bib taps brass cromium plated fancy type 15 mm bore size screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed

Supply & fix in repair short body bib taps brass cromium plated fancy type 15 mm bore size screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed

Supply & fix in repair brass chromium plated shower rose 100 mm size with shower arm square shpe 225mm long with flange complete all as specified and directed .

S&F in repair brass chromium plated towel rail 600 mm long, 20mm dia of a approved quality, complete all as specified & directed.

S&F in repair 75 mm PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall/ laid under floor etc in waste pipes and rain water pipes incuding PVC Tee,socket elbow,clamp etc complete all as specified and directed

S&F in repair 110mm PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall/ laid under floor etc in waste pipes and rain water pipes incuding PVC Tee ,socket,elbow,clamp etc complete all as specified and directed

S&F 110mm/125mm PVC(SWR) Gully Trap setting and jointed with solvent cement complete all as specified and dircted.

S&F Shelves for WHB Samrt PTMT-300mm long .

S&F 127mm dia CP grating with hole complete all as specified and directed.

S&F 127mm dia CP grating without hole complete all as specified and directed.

S & F Vitrous China bowl urinal full stall type white and union for discharge pipe including flush pipe complete all as specified and directed.

S&F in repair 15mm bore pillar taps brass chromium plated, screwed down, high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed to iron pipe, fixed in repairs complete all as specified & directed.

S & F Urinal Spreader of PTMT any colour for fixing 15mm dia pipe(Minimum wieght 60grams

S & F Urinal Partition white of size 310x700mm about 40cm above floor line complete all as specified and directed

Surface excavation in soft/loose soil n. exc 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed

M&L Broken bricks hardcore of gauge 63mm deposited spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified

M&L for 75mm thick PCC 1:4:8 of type D-2 (using 40mm graded stone agrregate) as in sub base of floors etc complete all as specified and directed

M&L for sand filling under floors or in foundations including watering and consolidation complete all as directed.

S&F for machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60mm thickness M-35 grade complete all as specified and as directed.

Excavatiion in trenches n exc 1.5m wide and n exc 1.5m depth and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge.

M&L salt glazed stone ware drain pipes laid jointed and tested complete of dia of pipe 150mm.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested bore dia of pipe 150mm in cement concrete type C-2(1:3:6)

Construction of septic tank of 10 users capacity all as specified and shown in drawing No TD/217 dt 27 Jun 1991 Sheet No 1/2 to 2/2 including excavation and earth work in any type soil, PCC 1:2:4 type B2 in floor/foundation, all brick work in wall shall be in CM 1:4 using sub class 'B' bricks, internal plaster 15 mm thick in CM 1:4, RCC M-25 (Nominal Mix) slab with reinforcement as shown in drawings, Man hole cover shall be precast reinforced concrete ,MS steps all as shown in drawin gs and two coats of bitumenous paint shall be applied on it, CI Vent/Outlet pipes including cowls shall be all as shown in drawings, Baffle wall shall be RCC M-25 (Nominal Mix) as shown on drawings complete all as directed by Engr-in-Charge

Construction of soak well 1.8m dia and 3m effective depth all as specified and shown in drawing No TD 576 dt 16 Jun 89 Sheet No 1/2 to 2/2 including excavation and earth work in any type soil, PCC 1:3:6 type C2 in foundation, Dwarf wall shall be of PCC 1:4:8 type D2, brick work in wall shall be in CM 1:6 using sub class 'B' bricks and honey comb shall be in CM 1:4, RCC M-25 (Nominal Mix) slab with reinforcement as shown in drawings, Band shall be PCC 1:2:4 type B1 and brick bats shall be with hand broken bricks of gauge not exceeding 100 mm complete all as directed by Engr-in-Charge

M&L for point wiring for light / fan/ Exhaust fan controlled by one switch with 1.5 sqmm single core 1100v grade FRLSH PVC insulated unsheathed multistranded copper conductor with and including PVC concealed conduit of medium grade (ISI Marked) having dia. not less than 20mm with all fittings including MS galvanised pressed steel terminal sunken boxes of thickness not less than 1.0 mm of required module for mounting modular switches, sockets etc. including 1.5 sqmm single core 1100v grade FRLSH PVC insulated unsheathed multistranded copper conductor as earth continuity conductor connected to common earth dolly and including cutting chases in walls / floors for concealed conduiting and making good disturbed surface area and white wash/colour wash to matching with the existing colour and all as specified and directed .

All as per srl item No 78 above but for 5 pin 5 amps socket outlet independent board complete all as specified and directed.

All as per item No. 78 here-in-before but by using 2.5 Sqmm FRLSH copper conductor cable with continuous earth wire of 2.5 Sqmm FRLSH copper conductor for one 3 pin 15 Amp socket outlet point controlled by one switch.

S&F switch modular type 10 Amps, 230 V AC, single pole, one way complete all as specified and directed.

S&F switch modular type 16 Amps, 230 V AC, single pole, one way complete all as specified and directed.

S&F socket out let multipurpose modular for 2 pin and 3 pin, 5 Amp flush type with shutter complete all as specified and directed.

S&F socket out let multipurpose modular for 2 pin and 3 pin, 15 Amp flush type with shutter complete all as specified and directed.

Supply and fix ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body complete all as specified & directed.

S & F Wall / surface mounted type LED light fitting batten type complete with LED lamp 10- watt (2 feet long), poly carbonate body and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with twine core twisted flexible copper conductor cable complete all as specified and as directed.

S & F Wall/surface mounted type LED light fitting batten type complete with LED 1x 20 watt (4 feet long), extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with 3 core twisted flexible copper conductor cable complete all as specified and as directed.

S & F Wall / surface mounted type Bulk Head LED light fitting complete with LED lamp 10 watt , extruded aluminium heat sink provide for efficient heat dissipation and integrate electronic driver complete with all accessories internally pre-wired and including connecting up with 3 core twisted flexible copper conductor cable complete all as specified and as directed.

Supply and fixing air ventilating fan 250 mm sweep PVC body, AC, single phase, 230 volts, 1200 RPM complete with in-built louvers shutters and including PVC insulated 2 core 1.5 sqmm copper cable from ceiling rose to exhaust fan complete including cutting the square / round hole of required size in wall, finishing the same for distrubed surfaces to match with the adjoining surfaces all as specified and directed.

Supply and fix in replacement of sheet metal enclosure distribution board, single pole and neutral, AC, 240 volt, 04 way, double door with 100 Amp rated copper bus bar and metal door with IP - 43protection and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

S & F MCB SPN 240 volts, 'C' curve of rating 32 amps, with rupturing capacity 10 KA, including providing thimble for out going cables.

S & F MCB single pole 240 volts, 'C' curve of rating from 6 to 32 amps, with rupturing capacity 10 KA,including providing thimble for out going cables.

Excavation in trenches n. exc 1.5 m wide and n.exc 1.5 m in depth and getting out soft /loose soil complete all as specified and as directed for laying of under ground cable/pipe etc. complete all as specified and as directed

Returning, filling in, including spreading, leveling, watering and well ramming in layers n. exc 25 cm thick in soft/loose soil, complete, all as specified and directed.

Removing surplus excavated material to a distance not exc 50 meter and depositing where directed at level not exc 1.5m above the starting point, complete, all as specified and directed.

Material and labour for providing sand cushioning with dry fine sand including filling, spreading, levelling in layers in cable trench with approved quality of sand for protection of under ground cable complete all as specified and directed.

Supplying & laying burnt clay bricks, sub class 'B', designation 75, old size laid in trenches over cable protection complete all as specified and directed.

M&L for 40mm bore GI tubing light grade with all fittings laid across road or across PCC drains, along electric pole or floor/wall for cable protection complete all as specified and directed.

Supply, laying and testing of LT cable 1100 volt grade XLPE insulated underground electric cable PVC bedded and sheathed steel wire/strip armoured aluminum stranded conductor of size 10 Sq mm 2 core complete all as specified and directed.

M&L in replacement earthing complete with galvanised steel earth plate electrode 600x600x6.00 mm thick, burried directly in ground vertically to a depth not less than 2.25 mtr deep below GL with top edge of the plate not less than 1.5 mtr below normal GL and connected to earth plate . Earth plate surrounded by 15 cm thick packed layers of charcoal/coke and common salt upto 0.90 meter depth all around the earth plate and connected to earth lead of GI wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel and thimbles and other end of the earth wire connected to equipments/panels and protected by galvanized iron or steel pipe light grade 20 mm bore and water pipe 20 mm bore GI medium grade with funnel and wire mesh, including all necessary excavation and earth work PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover and all as shown in electrical plate No 3 of MES schedule Pt I of 2009 and also including making test point for testing of earthing complete all as specified and as directed. Note : 1. RCC pit cover shall be pre-cast of RCC (1:2:4) type B-I , 50mm thick reinforced with XPM weighting not less than 4 KG/sqmm in lieu of CI cover. 2. Charcoal/coke and common salt upto 0.90 meter depth shall be filled in layers of 15 centimeters all around the earth plate. 3. On testing after completion of earthing if desired earth resistance is not achieved , the earthing will be redone at no extra cost to obtain the desired earth values.

M&L for Cutting existing 40mm bore steel tubing for alterations or additions complete all as specified and directed.

M&L for Screwing existing 40 or 50mm bore steel tubing for alterations or additions (or lengthening screw on pipe to form connector) complete all as specified and directed.

Supply and lay pipe galvanized, “Medium grade”, including fittings 25 mm (1”) bore complete all as specified and directed.

Supply and fixing 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

m/s pal associates