Loading
Loading…
Loading…
Tender Value
₹2.9 Cr
EMD Value
₹5.9 L
Closing Date
12 Oct 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
CIVIL MTN
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract.
Defination of Similar Work :- Any Civil Engineering works involving construction/modification/repair and maintenance of building/structure involving general construction activities viz concreting, masonry etc.
4 conditions
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
COMPLETION PERIOD The Contractors shall have to complete the work in all respects within a period of 08(Eight) months including monsoon from the date issue of acceptance of the tender. The Contractor s will have to employ labour in full strength commensurate with working areas available. He will also arrange for materials and equipments to complete the job most expeditiously within the stipulated completion period. The Engineer s decision as to what is full strength will be final. He should also submit bar-chart for completing the work in time. The contractor/s will be required to maintain speedy and required progress to the satisfactions of the Engineer to ensure that the work will be completed in all respects within the stipulated period failing which action may be taken by the Railway Administration in terms of Clause 17 and/or clause 62 of the General Conditions of Contract, 2022. MAINTENANCE PERIOD The tenderer s shall be required to maintain the work effectively for a period of 12 (twelve) months from the date of completion as per Clause No.47 of the General Conditions of Contract 2022 and no part refund of Security Deposit shall be permitted during the maintenance period mentioned above.
(i)Renovation of Conference Halls in various directorates of RDSO(ii) Replacement of furniture of ORH, DG Cell/Office etc (Part Work)(iii) Improvement works in Arunoday Vidhalaya, Manak Nagar Inter Collage, old & new Rajdhani hall, Audotorium and ORH, VIP & VVIP Rest house etc.(Balance Work)
WKS-1500-DC~RDSO
WKS-1500-DC
Open
Works - General
8 Months
Lucknow, Uttar Pradesh
₹0
₹5.9 L
16 Sept 2026
16 Sept 2026
28 Sept 2026
91 items across 2 schedules · ₹3,37,13,486.21 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | DSR Item No 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width aswell as 10 sqm on plan) including getting out and disposal of excavatedearth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil | cum | — | — | 3,725 |
| 2 | DSR Item No 4.1.3 Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinthlevel : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from naturalsources : 4 graded stone aggregate 20 mm nominal sizederived from natural sources) | cum | 15.00 | 7,365.15 | 1,10,477.25 |
| 3 | DSR Item No 4.1.8 Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinthlevel :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from naturalsources : 8 graded stone aggregate 40 mm nominal sizederived from natural sources) | cum | 18.00 | 6,326 | 1,13,868 |
| 4 | DSR Item No 5.1.2 Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing andreinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from naturalsources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 8.00 | 8,364.2 | 66,913.6 |
| 5 | DSR Item No 5.3 Reinforced cement concrete work in beams, suspended floors, roofshaving slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinthlevel up to floor five level, excluding the cost of centering, shuttering,finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarsesand(zone-III) derived from natural sources : 3 graded stone aggregate20 mm nominal size derived from natural sources). | cum | 8.00 | 10,391.4 | 83,131.2 |
| 6 | DSR Item No 5.9.3 Centering and shuttering including strutting, propping etc. and removalof form for Suspended floors, roofs, landings, balconies and accessplatform | Sqm | 25.00 | 766.55 | 19,163.75 |
| 7 | DSR Item No 5.9.5Centering and shuttering including strutting, propping etc. and removalof form forLintels, beams, plinth beams, girders, bressumers andcantilevers | Sqm | 25.00 | 608.35 | 15,208.75 |
| 8 | DSR Item No 5.22A.4 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Hot rolled deformed bars | Kg | 820.00 | 89.65 | 73,513 |
| 9 | DSR Item No 6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 15.00 | 6,658.25 | 99,873.75 |
| 10 | DSR Item No 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level inall shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 22.00 | 8,288.4 | 1,82,344.8 |
| 11 | DSR Item No 8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanitycounters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. completeat all levels.Granite stone slab colour black, Cherry/Ruby redArea of slab over 0.50 sqm | Sqm | 195.00 | 4,425.35 | 8,62,943.25 |
| 12 | DSR Item No 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming toIS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black ofany size as approved by Engineer-in-Charge, in skirting, risers of stepsand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shadecomplete. | Sqm | 750.00 | 1,063.45 | 7,97,587.5 |
| 13 | DSR Item No 9.20.2 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction withframe of 1st class hard wood and well matched teak 3 ply veneeringwith vertical grains or cross bands and face veneers on both faces ofshutters.30 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws | Sqm | 85.00 | 2,818.5 | 2,39,572.5 |
| 14 | DSR Item No 9.96.1Providing and fixing aluminium sliding door bolts, ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screwsetc. complete : 300x16 mm | Numbers | 65.00 | 260.3 | 16,919.5 |
| 15 | DSR Item No 9.97.2 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyedto required colour or shade, with necessary screws etc. complete :250x10 mm | Numbers | 65.00 | 104.4 | 6,786 |
| 16 | DSR Item No 9.100.1 Providing and fixing aluminium handles, ISI marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyedto required colour or shade, with necessary screws etc. complete :125 mm | Numbers | 105.00 | 60.05 | 6,305.25 |
| 17 | DSR Item No 9.105.1 Providing and fixing partition upto ceiling height consisting of G.I. frameand required board, including providing and fixing of frame work made ofspecial section power pressed/ roll form G.I. sheet with zinc coating of120 gms/sqm(both side inclusive), consisting of floor and ceiling channel50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed tothe floor and ceiling at the spacing of 610 mm centre to centre withdash fastener of 12.5 mm dia meter 50 mm length or suitable anchorfastener or metal screws with nylon plugs and the studs 48 mm widehaving one flange of 34 mm and other flange 36 mm and 0.50 mm thickfixed vertically within flanges of floor and ceiling channel and placed ata spacing of 610 mm centre to centre by 6 mm dia bolts and nuts,including fixing of studs along both ends of partition fixed flush to wallwith suitable anchor fastener or metal screws with nylon plugs at spacingof 450 mm centre to centre, and fixing of boards to both side of framework by 25 mm long dry wall screws on studs, floor and ceiling channelsat the spacing of 300 mm centre to centre. The boards are to be fixed tothe frame work with joints staggered to avoid through cracks, M.S.fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5mm each) to be provided at the horizontal joints of two boards, fixed tothe studs using metal to metal flat head screws, including jointing andfinishing to a flush finish with recommended jointing compound, jointingtape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisherand two coats of primer suitable for board as per manufacture'sspecification and direction of engineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick doubleskin fire rated Glass Reinforced Gypsum (GRG) plaster boardconforming to IS: 2095: part 3 (Board with BIS certificationmarks) | Sqm | 55.00 | 1,797.65 | 98,870.75 |
| 18 | DSR Item No 9.143 Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm(± 0.2 mm), corners of the door frame to be mitred cut and jointed withplastic brackets and stainless steel screws, reinforcing hinge sidevertical of the frames with PVC profile of Size 28 mm x 30 mm havingwall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of125 mm long stainless steel hinges to the frame, fixing the frame withjamb with required number & size of anchor dash fastners, all completeas per manufacturer's specification and direction of Engineer-in- charge. | Metre | 175.00 | 545.6 | 95,480 |
| 19 | DSR Item No 9.144 Providing and fixing 37 mm thick factory made PVC door shutter, stylesand rails made of PVC hollow section of size 100 mm x 37 mm withwall thickness 2 mm (± 0.2 mm), with inbuilt bead on one side, stylesand rails mitered cut and joint at the corners by means of 2 nos ofplastic brackets of size 75 mm x 220 mm at each corner and stainlesssteel screws, reinforcing the hinge side of style by inserting PVC profileof size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrailof size 100 mm x 37 mm, wall thickness 2 mm (+ 0.2 mm) will be fixedto the vertical styles. Providing with PVC snapfit beads and panel ofsize 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia andfastening with nuts and washers complete, all as per manufacturer'sspecification and direction of Engineer-in-charge | Sqm | 30.00 | 3,654.45 | 1,09,633.5 |
| 20 | DSR Item No 9.147A5.2 Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from rollforming process of required length (shape & size according to uPVCprofile), uPVC extruded glazing beads of appropriate dimension, EPDMgasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (whitepowder coated) casement handles, G.I fasteners 100 x 8 mm size forfixing frame to finished wall, plastic packers, plastic caps and necessarystainless steel screws etc. Profile of frame & sash shall be mitred cutand fusion welded at all corners, mullion (if required) shall be also fusionwelded including drilling of holes for fixing hardware's and drainage ofwater etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealant over backer rod ofrequired size and of approved quality, all complete as per approveddrawing & direction of Engineer-in-Charge. (Single / double glass panesand silicon sealant shall be paid separately). Variation in profile dimensionin higher side shall be accepted but no extra payment on this accountshall be made.Three track three panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R3 series with frame (98mm & above) x (40mm & above) & sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on two end panels along with multi-point locking system (Height upto 1.8 meter). | Sqm | 150.00 | 7,832.8 | 11,74,920 |
| 21 | DSR Item No 10.1 Structural steel work in single section, fixed with or without connectingplate, including cutting, hoisting, fixing in position and applying a primingcoat of approved steel primer all complete. | Kg | 320.00 | 93.05 | 29,776 |
| 22 | DSR Item No 10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubesetc.) trusses etc., including cutting, hoisting, fixing in position andapplying a priming coat of approved steel primer, including welding andbolted with special shaped washers etc. complete.Hot finished welded type tubes | Kg | 1000.00 | 155.4 | 1,55,400 |
| 23 | DSR Item No 10.25.2 Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steelprimer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets,gates and similar works | Kg | 750.00 | 142.3 | 1,06,725 |
| 24 | DSR Item No 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollowtubes, channels, plates etc., including welding, grinding, buffing, polishingand making curvature (wherever required) and fitting the same withnecessary stainless steel nuts and bolts complete, i/c fixing the railingwith necessary accessories & stainless steel dash fasteners , stainlesssteel bolts etc., of required size, on the top of the floor or the side ofwaist slab with suitable arrangement as per approval of Engineer-incharge,(for payment purpose only weight of stainless steel membersshall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.) | Kg | 2500.00 | 612.25 | 15,30,625 |
| 25 | DSR Item No 11.37 Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conformingto IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm includingpointing the joints with white cement and matching pigment etc.,complete. | Sqm | 125.00 | 935.6 | 1,16,950 |
| 26 | DSR Item No 11.41A.1.3 Providing and laying Vitrified tiles in floor in different sizes (thickness tobe specified by the manufacturer) with water absorption less than 0.08%and conforming to IS:15622, of approved brand & manufacturer, in allcolours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm includinggrouting the joints with white cement and matching pigments etc. Thetiles must be cut with the zero chipping diamond cutter only . Laying oftiles will be done with the notch trowel, plier, wedge, clips of requiredthickness, leveling system and rubber mallet for placing the tiles gentlyand easily.Double charge vitrified tile polished finish of sizeSize of Tile 600 x 1200 mm | Sqm | 1850.00 | 1,407.05 | 26,03,042.5 |
| 27 | DSR Item No 11.52.1 Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns incombination with Italian marble stones of different colours, shades andfinished surface texture etc., in linear portions of the building, all completeas per the architectural drawings, with 18 mm thick stone slab laid over20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarsesand) laid and jointed with white cement slurry @ 4.4 kg/sqm, includingpointing with white cement slurry admixed with pigment to match themarble shade, including rubbing, curing and polishing etc. all completeas specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona,Fire Red or Dark Emperadore etc. | Sqm | 55.00 | 6,389.4 | 3,51,417 |
| 28 | DSR Item No 12.35 Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183. Density 16 kg/m³, 50 mm thick, wrappedin 200G Virgin Polythene bags placed over existing false ceilingand held in position by criss-crossing GI wire. | Sqm | 1850.00 | 242.8 | 4,49,180 |
| 29 | DSR Item No 12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain waterpipes conforming to IS : 13592 Type A, including jointing with sealring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.110 mm diamete | Metre | 250.00 | 319.75 | 79,937.5 |
| 30 | DSR Item No 12.42.5.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conformingto IS : 13592 Type A, including jointing with seal ring conforming toIS : 5382, leaving 10 mm gap for thermal expansionBend 87.5°110 mm bend | Numbers | 55.00 | 132 | 7,260 |
| 31 | DSR Item No 12.42.6.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conformingto IS : 13592 Type A, including jointing with seal ring conforming toIS : 5382, leaving 10 mm gap for thermal expansionShoe (Plain)110 mm Shoe | Numbers | 55.00 | 115.95 | 6,377.25 |
| 32 | DSR Item No 1 2 . 4 3 . 2 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mmhard wood plugs, screwed with M.S. screws of required length,including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete.110 mm | Numbers | 75.00 | 310.85 | 23,313.75 |
| 33 | DSR Item No 12.57 Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick,wrapped in 200G Virgin Polythene Bags fixed to wall with screw,rawel plug & washers and held in position by criss crossing GI wireetc. complete as per directions of Engineer- in-Charge | Sqm | 1110.00 | 307.35 | 3,41,158.5 |
| 34 | DSR Item No 13.4.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) | Sqm | 915.00 | 294.35 | 2,69,330.25 |
| 35 | DSR Item No 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete. | Sqm | 1520.00 | 123.85 | 1,88,252 |
| 36 | DSR Item No 13.81.1 Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approvedbrand and manufacture, including applying additional coats whereverrequired, to achieve even shade and colour.Distempering with 1st quality acrylic distemper, having VOC (VolatileOrganic Compound ) content less than 50 grams/ litre, of approvedbrand and manufacture, including applying additional coats whereverrequired, to achieve even shade and colour. | Sqm | 1520.00 | 51.8 | 78,736 |
| 37 | DSR Item No 13.91 Removing dry or oil bound distemper, water proofing cement paintand the like by scrapping, sand papering and preparing the surfacesmooth including necessary repairs to scratches etc. complete. | Sqm | 1540.00 | 20.85 | 32,109 |
| 38 | DSR Item No 13.99.1 Painting with synthetic enamel paint of approved brand andmanufacture of required colour to give an even shade :One or more coats on old work | Sqm | 320.00 | 86.55 | 27,696 |
| 39 | DSR Item No 13.112.1 Finishing walls with Premium Acrylic Smooth exterior paint withSilicone additives of required shade Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm)over existing cement paint surface | Sqm | 850.00 | 106.55 | 90,567.5 |
| 40 | DSR Item No 15.7.4 Demolishing brick work manually/ by mechanical means includingstacking of serviceable material and disposal of unserviceable materialwithin 50 metres lead as per direction of Engineer-in- charge.In cement mortar | cum | 8.00 | 1,698.45 | 13,587.6 |
| 41 | DSR Item No 15.12.1 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete andstacking within 50 metres lead :Of area 3 sq. metres and below | Numbers | 110.00 | 302.7 | 33,297 |
| 42 | DSR Item No 15.23.1 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm | Sqm | 1850.00 | 60.5 | 1,11,925 |
| 43 | DSR Item No 15.56 Dismantling old plaster or skirting raking out joints and cleaning thesurface for plaster including disposal of rubbish to the dumping groundwithin 50 metres lead. | Sqm | 850.00 | 45.05 | 38,292.5 |
| 44 | DSR Item No 15.60 Disposal of building rubbish / malba / similar unserviceable, dismantledor waste materials by mechanical means, including loading,transporting, unloading to approved municipal dumping ground or asapproved by Engineer-in-charge, beyond 50 m initial lead, for all leadsincluding all lifts involved. | cum | 55.00 | 219.3 | 12,061.5 |
| 45 | DSR Item No 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever) conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required:White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests | Numbers | 8.00 | 5,781.35 | 46,250.8 |
| 46 | DSR Item No 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the wallswherever require: White Vitreous China Wash basin size 630x450 mmwith a pair of 15 mm C.P. brass pillar taps | Each | 22.00 | 2,275 | 50,050 |
| 47 | DSR Item No 17.10.1.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink asper IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making goodthe walls wherever required :Kitchen sink with drain board510x1040 mm bowl depth 250 mm | Each | 10.00 | 6,008.45 | 60,084.5 |
| 48 | DSR Item No 17.28.1.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe32 mm dia | Numbers | 25.00 | 90.95 | 2,273.75 |
| 49 | DSR Item No 17.31 Providing and fixing 600x450 mm beveled edge mirror of superiorglass (of approved quality) complete with 6 mm thick hard boardground fixed to wooden cleats with C.P. brass screws and washerscomplete. | Numbers | 10.00 | 1,411.15 | 14,111.5 |
| 50 | DSR Item No 18.16.1 Providing and fixing brass stop cock of approved quality :15 mm nominal bore | Numbers | 50.00 | 303.85 | 15,192.5 |
| 51 | DSR Item No 18.21.2.2 Providing and fixing uplasticised PVC connection pipe with brassunions : 20 mm nominal bore | Numbers | 14.00 | 102.6 | 1,436.4 |
| 52 | DSR Item No 18.50.1 Providing and fixing C.P. brass long nose bib cock of approved qualityconforming to IS standards and weighing not less than 810 gms.15 mm nominal bore | Numbers | 18.00 | 715.05 | 12,870.9 |
| 53 | DSR Item No 18.58.1.1 Providing and fixing PTMT grating of approved quality and colour.Circular type100 mm nominal dia | Numbers | 18.00 | 33.2 | 597.6 |
| 54 | DSR Item No 21.1.1.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparentor dyed to required shade according toIS: 1868, Minimum anodic coating of gradeAC 15) | Kg | 110.00 | 433.95 | 47,734.5 |
| 55 | DSR Item No 21.1.2.1 Providing and fixing aluminium work for doors, windows, ventilatorsand partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS: 1285, fixing with dash fasteners ofrequired dia and size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required includingcleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architecturaldrawings and the directions of Engineer-in-charge. (Glazing, panelingand dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators includingproviding and fixing hinges/ pivots and making provisionfor fixing of fittings wherever required including the costof EPDM rubber / neoprene gasket required (Fittingsshall be paid for separately)Anodised aluminium (anodised transparentor dyed to required shade according toIS: 1868, Minimum anodic coating of gradeAC 15) | Kg | 115.00 | 521.25 | 59,943.75 |
| 56 | DSR Item No 21.2.2 Providing and fixing 12 mm thick prelaminated particle board flatpressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windowsshutters and partition frames with C.P. brass / stainless steel screwsetc. complete as per architectural drawings and directions of engineerin-charge.Pre-laminated particle board with decorative laminationon both sides | Sqm | 55.00 | 951.05 | 52,307.75 |
| 57 | DSR Item No 21.3.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasketetc. complete as per the architectural drawings and the directions ofengineer-in- charge . (Cost of aluminium snap beading shall be paidin basic item):With float glass panes of 5 mm thickness (weight notless than 12.50 kg/sqm) | Sqm | 275.00 | 1,325.55 | 3,64,526.25 |
| 58 | DSR Item No 21.4.1 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logoembossed on the body / plate with double spring mechanism anddoor weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good the same matchingto the existing floor finishing and cover plates with brass pivot andsingle piece M.S. sheet outer box with slide plate etc. complete asper the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mmthickness | Numbers | 11.00 | 2,448.85 | 26,937.35 |
| 59 | DSR Item No 21.18 Providing and fixing 12mm thick frameless toughened glassdoor shutter of approved brand and manufacture, including providingand fixing top & bottom pivot & double acting hydraulic floor springtype fixing arrangement and making necessary holes etc. for fixingrequired door fittings, all complete as per direction of Engineer in charge(Door handle, lock and stopper etc. to be paid separately) | Sqm | 50.00 | 4,540.7 | 2,27,035 |
| 60 | DSR Item No 25.1 Providing and supplying aluminium extruded tubular and otheraluminium sections as per the architectural drawings and approvedshop drawings , the aluminium quality as per grade 6063 T5 or T6 asper BS 1474,including super durable powder coating of 60-80 micronsconforming to AAMA 2604 of required colour and shade as approvedby the Engineer-in-Charge. ( The item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extrudedaluminium frame work. Nothing extra shall be paid on this account).The weight of aluminium extruded section shall be taken for purposeof payment. | Kg | 520.00 | 370.45 | 1,92,634 |
| 61 | DSR Item No 26.27.1 Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles shouldhave Humidity Resistance (RH) of 99%, Light Reflectance ? 85%,Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance asper (BS 476 pt - 6 &7)in true horizontal level suspended on interlockingT-Grid of hot dipped all round galvanized iron section of 0.33 mm thick(galvanized @ 120 gsm) comprising of main T runners of 15x32 mm oflength 3000 mm, cross T of size 15x32mm of length 1200 mm andsecondary intermediate cross T of size 15x32 mm of length 600 mmto form grid module of size 600x600 mm suspended from ceiling usinggalvanized mild steel item (galvanised@ 80gsm) 50 mm long 8mmouter diameter M-6 dash fasteners, 6 mm diameter fully threadedhanger rod up to 1000 mm length and L-shape level adjuster of size85x25x2 mm, spaced at 1200 mm centre to centre along main 'T'.The system should rest on periphery walls /partitions with the help ofGI perimeter wall angle of size24x24X3000 mm made of 0.40 mmthick sheet, to be fixed to the wall with help of plastic rawl plug at 450mm centre to centre & 40 mm long dry wall S.S. screws. The exposedbottom portion of all T-sections used in false ceiling support systemshall be pre-painted with polyester baked paint, for all heights. Thework shall be carried out as per specifications, drawings and as perdirections of the engineer-in-charge.With 16 mm thick beveled tegular mineral fibre falseceiling tile (NRC 0.55 to 0.6) | Sqm | 855.00 | 2,069.9 | 17,69,764.5 |
| 62 | DSR Item No 26.27.2 Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles shouldhave Humidity Resistance (RH) of 99%, Light Reflectance ? 85%,Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance asper (BS 476 pt - 6 &7)in true horizontal level suspended on interlockingT-Grid of hot dipped all round galvanized iron section of 0.33 mm thick(galvanized @ 120 gsm) comprising of main T runners of 15x32 mm oflength 3000 mm, cross T of size 15x32mm of length 1200 mm andsecondary intermediate cross T of size 15x32 mm of length 600 mmto form grid module of size 600x600 mm suspended from ceiling usinggalvanized mild steel item (galvanised@ 80gsm) 50 mm long 8mmouter diameter M-6 dash fasteners, 6 mm diameter fully threadedhanger rod up to 1000 mm length and L-shape level adjuster of size85x25x2 mm, spaced at 1200 mm centre to centre along main 'T'.The system should rest on periphery walls /partitions with the help ofGI perimeter wall angle of size24x24X3000 mm made of 0.40 mmthick sheet, to be fixed to the wall with help of plastic rawl plug at 450mm centre to centre & 40 mm long dry wall S.S. screws. The exposedbottom portion of all T-sections used in false ceiling support systemshall be pre-painted with polyester baked paint, for all heights. Thework shall be carried out as per specifications, drawings and as perdirections of the engineer-in-charge.With 20 mm thick beveled tegular mineral fibre falseceiling tile (NRC 0.7) | Sqm | 900.00 | 2,358.15 | 21,22,335 |
| Schedule total | ₹1,59,40,340.25 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
DetailedDescriptionofNSitems.pdf NS Items
ATTACHMENT
Tenderpdf1.pdf
ATTACHMENT
tenderpdf2.pdf
ATTACHMENT
tenderpdf3.pdf
ATTACHMENT
SpecialCondition.pdf
ATTACHMENT
tenderpdf4-compressed.pdf
ATTACHMENT
DetailedDescriptionofNSitems.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .