CONSTRUCTION OF SUTRUPRAHARA MANDAPAM BY USING MANGALORE TILED ROOF AT ARULMIGU VELAYUTHASWAMY TEMPLE THINDAL ERODE TALUK AND DISTRICT

Amount

CONSTRUCTION OF SUTRUPRAHARA MANDAPAM BY USING MANGALORE TILED ROOF AT ARULMIGU VELAYUTHASWAMYTEMPLE ,THINDAL, ERODE TALUK OF ERODE DISTRICT.

Earth work excavating and depositing on bank with an initial lead of 10m and initial lift of 2m in sand,silt or loose soil,wet sand or silt not under water,light black cotton soil,sandy loam and ordinary soil including excavated earth, Hard stiff clay, hard red earth, shales,murram, gravel, stoney earth and earth mixed with small size boulders, soft disintegrated rock,laterite,soft rock or kankar not requiring blasting including clearing,levelling the site etc., complying with standard specification and as directed by the departmental officers (Narrow excavation)

Providing and laying Plain Cement concrete of 1:2:4(one cement Two M sand Four stone jelly) using 20mm stone jelly mixed with mixer machine including dewatering by bailing/pumping wherever necessary laying the concrete in layers and in bays with all leads and lifts, compacting and finishing the surface, watering, curing etc., complete complying with standard specifications and as directed by the departmental officers

Supplying and erecting Steel shuttering including necessary supports for Plane Surfaces in foundation and basement for reinforced cement concrete works such column footings, plinth beam, Grade beam, Stair Case steps, bed blocks etc., which requires only nominal strutting using stiffened with mild steel sheets of suitable size 90cm x60cm and BG 10 stiffened with mild steel angles of size mm of 25mm x 25mm x 3 mm for boardinglaid over silver oak joists of size 10cm x 6.50 cm spaced at about 60 cm centre to centre and supported by the casurina props of 10 cm to 13 cm dia paced at 75 cm centre to centre or at suitable intervals etc., complete

Providing and erecting Steel column using Circular Hollow section pipe dia 219.10mm & tk 8 mm to a height of 7.09m,,2.65m & 2.29m from floor level. The column should be fixed in steel baseplate of size 375x375x16mm. The base plate should be drilled in four holes of 16mm dia should be fixed in 16mm dia hility bolts at a distance of 275mm c/c on each sides. The end of steel column should be fixed in steel end plate 2 nos of size 375x375x12mm. The end plate should be drilled in four holes of 16mm dia should be fixed in 16mm dia connection bolts at a distance of 275mm c/c Both bottom and top of steel pipe column should be placed with stiffner plate of size 78x150x8mm tk as per drawing . The Quality of steel, fabrication works & welding works are strictly followed in IS code as mention in the approved drawing. The cost includes cost of all materials, process charges like gas cutting, welding, machining, scaffolding charges, labour charges for dismantling, loading, lifting, unloading, transport, erection, labour charges for equipments like crane, chain pulley block, power charges from generator, risk allowance for working at a height of more than 3m, conveyance to site and clearing them after completion of work complete and as directed by the departmental officers

Providing and erecting Steel Main Rafter 1,2,3& 4 using Rectangular hollow steel Rafter of size 172x92x4.80mm and 200x100x4mm to a variable length should be conneted on eigther sides in exixting steel column top portion over steel wall beam. The steel rafter should be properly conneted in slope of 16 degree. The connection should be made with the main rafter connected with connection plate of size 125x70x12mm both sides plates around welding works are to be carried out. The Quality of steel, fabrication works & welding works are strictly followed in IS code as mention in the approved drawing. The cost includes cost of all materials, process charges like gas cutting, welding, machining, scaffolding charges, labour charges for dismantling, loading, lifting, unloading, transport, erection, labour charges for equipments like crane, chain pulley block, power charges from generator, risk allowance for working at a height of more than 3m, conveyance to site and clearing them after completion of work complete and as directed by the departmental officers

Providing and erecting Steel Tie Beam B2& B1 using Rectangular hollow steel section of size 300x150x6mmmm &240x120x6mm in front & Back side of existing temple building roof inner sides column to column. The beam should be conneted on eigther sides in exixting steel column top portion the connection should be made with connection plate of size 125x170x8mm both sides plates around welding works are to be carried out. The Quality of steel, fabrication works & welding works are strictly followed in IS code as mention in the approved drawing. The cost includes cost of all materials, process charges like gas cutting, welding, machining, scaffolding charges, labour charges for dismantling, loading, lifting, unloading, transport, erection, labour charges for equipments like crane, chain pulley block, power charges from generator, risk allowance for working at a height of more than 3m, conveyance to site and clearing them after completion of work complete and as directed by the departmental officers

Providing and erecting Steel Tie Beams using Rectangular hollow steel section of size B3: 200x100x4mm in Left & Right side of existing temple building roof inner sides column to column. and around outer sides of temple building. The beam should be conneted on eigther sides in exixting steel column top portion the connection should be made with connection plate of size 170x125x8mm both sides plates around welding works are to be carried out. The Quality of steel, fabrication works & welding works are strictly followed in IS code as mention in the approved drawing. The cost includes cost of all materials, process charges like gas cutting, welding, machining, scaffolding charges, labour charges for dismantling, loading, lifting, unloading, transport, erection, labour charges for equipments like crane, chain pulley block, power charges from generator, risk allowance for working at a height of more than 3m, conveyance to site and clearing them after completion of work complete and as directed by the departmental officers

Providing and erecting Steel Steel purline using Rectangular hollow steel section of size 50x25x2.60mm over steel rafter at 0.335m c/c . The purlin should be conneted on existing steel rafter,3mm tk welding works are to be carried out. All steel materials taken for fabrication should be straight ie free from twist. The Quality of steel, fabrication works & welding works are strictly followed in IS code as mention in the approved drawing. The cost includes cost of all materials, process charges like gas cutting, welding, machining, scaffolding charges, labour charges for dismantling, loading, lifting, unloading, transport, erection, labour charges for equipments like crane, chain pulley block, power charges from generator, risk allowance for working at a height of more than 3m, conveyance to site and clearing them after completion of work complete and as directed by the departmental officers

Supplying and fixing Best Quality Mangalore Tiles (I class A) over best Quality ceiling tiles 200x200x20mm over Steel rafters for all aroung Existing teple building The cost includes cost of all materials, scaffolding charges, etc complete. The Mangalore tiles and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification. and as directed by the departmental officers

Supplying and fixing best Quality Bolts and Nuts for Fabriction works The cost includes cost of all materials and fixing charges etc complete as per standard speicification. and as directed by the departmental officers

For16mm dia Best quality Hility Bolts 450mm length

For16mm dia Best quality Bolts

Painting new iron works such as steel Hollow pipes, Beams, purlin& all hollow section etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all steel components including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

GST Amount for providing Service to Government Contract Works for the above works at 18%(9%+9%). {GST Amount is the Total GST Amount for overall quoted amount}

SELVAMADHU DEVELOPERS PRIVATE LIMITED (BID ID -1405255)