Loading
Loading…
Loading…
Tender Value
₹1.5 Cr
EMD Value
₹3.0 L
Closing Date
29 May 2026, 4:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
ELECT.G
17 conditions · 5 needing a document upload
Financial Eligibility Criteria: (Ref: RB letter No. 2022/CE- I/CT/GCC2022/POLICY : Advance Correction Slip No.-1 dt 14.07.2022) The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-I, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The intending tenderers should possess a valid electrical contractor license at the time of opening of tender, issued by any state government & same should be submitted along with tender documents by all bidders including working contractors of this unit otherwise offer shall be summarily rejected....... IT SHOULD BE NOTED BY THE TENDERER THAT ELECTRICAL LICENSE UNDER RENEWAL AT THE TIME OF TENDER OPENING WILL NOT BE CONSIDERED AND OFFER WILL BE SUMMARILY REJECTED. IT IS THE RESPONSIBILITY OF TENDERER TO UPLOAD VALID ELECTRICAL CONTRACTOR LICENSE ON THE DATE OF TENDER OPENING.
All requisite documents mentioned in clause 3.7 of the tender document attached pertaining to constitution of firm/concern. (As applicable).
36 conditions · 4 needing a document upload
The rate to be quoted by tenderer shall be inclusive of all state/central taxes including GST. THE TENDERER SHOULD UPLOAD VALID GST REGISTRATION CERTIFICATE ALONG WITH THE OFFER.
The tender shall comply with General Condition of contract (GCC),2022 of Indian Railways (file attached). and its latest amendment, if any. The tenderer shall submit the offer after duly satisfying himself/herself with the GCC,2022 in general.
Tenderers are required to upload the Bank details as per Annexure-XII (Real Time Gross Saving (RTGS)/National Electronic Fund Transfer (NEFT) Model Mandate Form)of tender document.
Tenderers are required to upload requisite details as per Annexure-VIIB (DETAILS OF CONTRACTUAL PAYMENT RECEIVED IN LAST THREE FINANCIAL YEARS AND CURRENT FINANCIAL YEAR) without which the offer is liable to be rejected.
Tenderers are compulsorily required to upload Affidavit as per Annexure-XXIV along with tender document, without which the offer will be considered incomplete and will be rejected summarily.
All requisite documents/credentials mentioned in clause 3.5 of the tender document attached pertaining to his/their technical and financial eligibility. (As applicable).
All requisite documents mentioned in clause 3.7 of the tender document attached pertaining to constitution of firm/concern. (As applicable).
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
No post tender correspondence for submission of additional documents shall be entertained after opening of the Technical & Commercial offers. Even suo-moto post tender letters of the tenderer/s shall be treated as Null & Void.
Defective parts shall only be replaced with OEM's spares. Proper invoices/delivery challan /warranty certificate etc. shall be provided by the firm to prove genuineness of spare parts.
This tender complies with Public Procurement Policy (Make in India) Order 2017, dated 15/06/2017, issued by Department of Industrial Promotion and Policy, Ministry of Commerce, circulated vide Railway Board letter no. 2015/RS(G)/779/5 dated 03/08/2017 and 27/12/2017.
IF ANY DISCREPANCY IS FOUND IN THE TENDER DOCUMENT, NAMELY SOR ITEM DESCRIPTION, SPECIAL TENDER CONDITION ETC., CLARIFICATION CAN BE SOUGHT FROM THE OFFICE OF SRDEE/G/DLI, DRM OFFICE, STATE ENTRY ROAD, NEW DELHI.
This tender complies with Railway Board instructions for Startups (recognized by Department of Industrial Policy and Promotion, Ministry of Commerce and Industry) for exemption from payment of Bid Security as detailed in GCC 2022 as amended from time to time. Such Startup firms may note that no other exemption is applicable to them in this particular tender.
On account payment, contractor shall submitted indemnity bond with validity up to the completion/extended period in the prescribed format (please refer Annexure-XXVIII) at the contractor's cost, vesting the ownership of such material with the railways.
This tender shall also complies with "Indian Railways Standard General Conditions of Contract, April 2022 (Advance Correction Slip No. 11)" vide Railway Board letter No. 2022/CE-I/CT/GCC- 2022/POLICY/Pt.I (E-3320424), dated: 13.03.2026 (attached)
All disputes or differences of any kind whatsoever arising out of or in connection with this contract, whether during its execution or after completion, termination, or breach thereof, shall be subject to the exclusive jurisdiction of the competent courts at New Delhi only.
The issues not covered under the tender document shall be governed by General conditions of Contract (GCC) 2022 or its latest amendments if any during entire period of contract. If any contradiction in Tender Document and GCC is observed then GCC shall prevail.
Electrical work in connection with (i) Construction of New Integrated Lobby and Running Room with allied offices at GHH, (ii) Upgradation of Lobby/running room at SSB by providing various facilities to Running staffs.
80-SRDEE-G-DLI-2026-27
80-SRDEE-G-DLI-2026-27
Open
Works - General
12 Months
Delhi, Delhi
₹0
₹3.0 L
29 May 2026
8 May 2026
15 May 2026
109 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,48,62,946 | ||
| — | 910.00 | — | — | ||
| Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FRLSH PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLSH PVC insulated copper conductor single core etc. as required and conforming to IS 694 or latest & CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. Group C | — | — | — | 12,83,100 | |
| — | 250.00 | — | — | ||
| Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required and conforming to IS 3854:2023/ IEC 60669-1, IS 14772:2020 & CPWD General Specifications for Electrical Works Part-I Internal - 2023 and CPWD DSR (E&M) 2022 & as per explanatory note. | — | — | — | 1,11,000 | |
| — | 200.00 | — | — | ||
| Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required and conforming to IS 3854:2023, IS 14772:2020 or latest & CPWD General Specifications for Electrical Works Part-I Internal - 2023 and CPWD DSR (E&M) 2022 & as per explanatory note. | — | — | — | 1,11,400 | |
| — | 500.00 | — | — | ||
| Supply, Fixing, testing & commissioning of ceiling rose, 3 plate conforming to IS : 371- 1999 (or Latest Version) & installation on the junction box of laid conduit including connections, testing & commissioning as per site requirement & as per explanatory note. | — | — | — | 35,000 | |
| — | 100.00 | — | — | ||
| Supply, Fixing, testing & commissioning of Batten/Angle Holder conforming to IS : 1258-2005 (or Latest Version) & installation on the junction box of laid conduit including connections, testing & commissioning as per site requirement & as per explanatory note. | — | — | — | 12,100 | |
| — | 3000.00 | — | — | ||
| Supply and recessing/fixing of PVC conduit pipe of size 25 mm conforming to IS. 9537 (Latest version) with accessories junction box, bends etc. including making chase, plastering/clamping etc. as per site requirement conforming to IS 9537 latest version & as per explanatory note. | — | — | — | 93,000 | |
| — | 10000.00 | — | — | ||
| Supply, fixing, testing & commissioning of following sizes FRLSH PVC insulated multi stranded copper (annealed) conductor single core cable conforming to IS 694 (or Latest Version), and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main as required as per technical specification including connections, testing and commissioning & as per explanatory note. 1x2.5 sq.mm | — | — | — | 4,30,000 | |
| — | 8000.00 | — | — | ||
| Supply, fixing, testing & commissioning of following sizes FRLSH PVC insulated multi stranded copper (annealed) conductor single core cable conforming to IS 694 (or Latest Version), and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main as required as per technical specification including connections, testing and commissioning & as per explanatory note. 1x4.0 sq.mm | — | — | — | 4,56,000 | |
| — | 5000.00 | — | — | ||
| Supply, fixing, testing & commissioning of following sizes FRLSH PVC insulated multi stranded copper (annealed) conductor single core cable conforming to IS 694 (or Latest Version), and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main as required as per technical specification including connections, testing and commissioning & as per explanatory note. 1x6.0 sq.mm | — | — | — | 4,70,000 | |
| — | 1000.00 | — | — | ||
| Supply, fixing, testing & commissioning of following sizes FRLSH PVC insulated multi stranded copper (annealed) conductor single core cable conforming to IS 694 (or Latest Version), and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main as required as per technical specification including connections, testing and commissioning & as per explanatory note. 1x10.0 sq.mm | — | — | — | 1,44,000 | |
| — | 150.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED light luminaire, having system wattage 1x18 watt. LED tube and inbuilt LED driver, CRCA body powder coated, complete with all mounting arrangement, accessories. The LED based 4 ft. tube light (lamp) shall be conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 1,02,900 | |
| — | 50.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED light luminaire, having system wattage 2x18 watt. LED tube and inbuilt LED driver, CRCA body powder coated, complete with all mounting arrangement, accessories. The LED based 4 ft. tube light (lamp) shall be conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 58,000 | |
| — | 140.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED bed side lights, system wattage 6W,CRI>80, 4000K/6000K, Housing made of aluminum/CRCA sheet with powder coated, mild steel neck, cool white with compatible inbuilt LED driver complete with prior approval of sample and shall be conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 87,059 | |
| — | 50.00 | — | — | ||
| Supply, fixing, testing and commissioning of 4-feet long surface mounting 36-Watt, 5700K,CRI>80, LED Luminaire as per CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest, IS, IE rules and site requirement. Fitting shall be environmentally friendly, long life, corrosion resistant, impact proof IP 66 with PC housing & opal finish cover suitable for wet location similar to Make - Havells Model No. MAGNUM NEO or equivalent Fitting shall be suitable for operation on single phase 240Volt, 50 Hz AC supply & as per explanatory note. | — | — | — | 1,65,300 | |
| — | 50.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED light luminaries 595x595 mm size, recessed mounting fitting (Tile type),as per IS : 10322 having system wattage less than or equal to 48 Watt, CRCA body powder coated, high efficiency milky white PMMA diffuser with no bright spot visible, complete with all mounting arrangement with suitable frame to avoid droping down of fitting of make Phillips, Bajaj, Havells or similar conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 1,76,200 | |
| — | 100.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED deep recessed down lighter, housing aluminum die cast, white powder coated and PMMA diffuser having system wattage less than or equal to 15 Watt complete with all mounting arrangement, accessories complete conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 1,22,400 | |
| — | 30.00 | — | — | ||
| Design, Supply, Fixing, testing and commissioning of Pendant luminaire Up Dn with LED (Light Emitting Diode), system power 28 W ( 14 W Up, 14 W Dn), luminous flux of luminaire 3360 lm, 110 Lm/w, direct - Indirect light emission ( 54 % Up, 46 % Dn), CRI>80, R9>20, THD<5%, P.F>0.95, Driver Efficiency>88%, SDCM<3, color temperature of 3000 K/4000 K/5700 K/ 6500 K (As per ANSI Bin), 230V constant current driver, 70% of luminous flux after 50,000 operating hours, energy-efficient LEDs, luminaire profile in aluminium, Plastic molded end caps, Polyester powder Aluminium white colored coat applied over a 5- stage pre-treatment, Deep recessed high-efficiency glare-free snap-fit micro-prismatic diffuser for homogeneous light distribution, UGR<19, ZHLS (Zero Halogen Low Smoke) internal wiring, integral electronic control gear, adjustable suspender, Protection class I, IP20, L = 1199 mm, B = 75 mm, H = 90 mm, PL max = 1500 mm. & conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 2,34,900 | |
| — | 30.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED based focus light having wattage less than or equal to 10W (approx.) complete with driver as per IS, IE rules, site requirement and prior approval of sample conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 19,350 | |
| — | 30.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED based picture light having wattage less than or equal to 10W (approx.) complete with driver as per IS, IE rules, site requirement and prior approval of sample conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 20,790 | |
| — | 4.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED Post Top 25W complete as per IS & IE rules, site requirement and prior approval of sample conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 21,796 | |
| — | 20.00 | — | — | ||
| Supply, fixing, testing and commissioning 15 W LED bollard light complete as per IS & IE rules, site requirement and prior approval of sample conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 1,18,400 | |
| — | 100.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED down lighter, housing aluminum die cast, white powder coated and PMMA diffuser having system wattage less than or equal to 15 Watt complete with all mounting arrangement, accessories complete conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 79,300 | |
| — | 50.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED down lighter, housing aluminum die cast, white powder coated and PMMA diffuser having system wattage less than or equal to 15-18 Watt complete with all mounting arrangement, accessories complete conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 42,500 | |
| — | 40.00 | — | — | ||
| Supply, fixing, testing & commissioning of 400 mm sweep BLDC wall mounted fan complete conforming to latest relevant IS/IEC standards & as per explanatory note. | — | — | — | 1,05,720 | |
| — | 150.00 | — | — | ||
| Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body. Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS 374:2019 or latest fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required & as per explanatory note. 1400mm, service value >= 6.0 CM/Min/Watt, air delivery 245 CM/Min (Minimum) | — | — | — | 4,37,850 | |
| — | 150.00 | — | — | ||
| Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required & as per explanatory note. | — | — | — | 50,700 | |
| — | 50.00 | — | — | ||
| Supply, fixing, testing and commissioning of 380mm sweep, 1400 rpm (approx) propeller type exhaust fan complete as per IS, IE rule & site requirement & as per explanatory note. Make Bajaj, Usha, Havells, Orient or equivalent | — | — | — | 1,57,450 | |
| — | 50.00 | — | — | ||
| Supply, fixing, testing and commissioning of 250mm sweep fresh air fan complete conforming to IS 2312 & IS 302 or latest and other relevant IS/IEC standards & as per explanatory note. | — | — | — | 1,57,450 | |
| — | 40.00 | — | — | ||
| Supply & erection of hot dip galvanized octagonal pole 5 Mtrs. long Double Arms, conforming to IS 2629/BSEN ISO 1461 latest version with top 70 mm and bottom 130 mm around face made of 3 mm thick, steel base plate size 200x200x12 mm complete with appropriate sleeve at the top of the pole for mounting arm bracket 300 mm long suitable for LED street light fittings including casting, muffing with cement concrete foundation (1:2:4) painting, earthing and foundation GI nut, bolts with washer and smart pack junction box with 1A single pole MCB and terminals. Pole junction box shall be sealed with water proof tape and display of danger sticker & as per explanatory note. Note- Wiring in between pole junction box to fitting shall be done through 3 cores 1.5 sq. mm double insulated weather proof cables conforming to IS 456 & other relevant IS/IEC standards | — | — | — | 4,12,480 | |
| — | 90.00 | — | — | ||
| Supply, fixing, testing and commissioning of 45 watt LED based street light luminary with cool white light, pressure die cast aluminum housing, IP 66 or better having system complete conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 2,84,580 | |
| — | 500.00 | — | — | ||
| Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required conforming to IS/IEC 61537:2006 or latest & as per explanatory note. 300 mm width X 50 mm depth X 1.6 mm thickness | — | — | — | 4,25,500 | |
| — | 4.00 | — | — | ||
| Supply, fixing, testing and commissioning of 25A/32 A,30 mA RCCB AC type confirming to IS 12640-1 & IEC 61008-1 with 10KA short circuit withstand capacity complete with enclosure & as per explanatory note. | — | — | — | 10,760 | |
| — | 80.00 | — | — | ||
| Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25A modular socket outlet and 25A modular SP MCB " C " curve including connections, painting etc. as required as per IS 13032:2016 or latest and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 and CPWD DSR (E&M) 2022 & as per explanatory note. | — | — | — | 54,000 | |
| — | 20.00 | — | — | ||
| Supply, installation, testing & commissioning of 25 ltrs. stationary storage type electric water heater (Geyser) having BEE star rating- 5 star, Installation :vertical, ABS Body, element wattage - 2 KW, Tank capacity -25 ltrs., conforming to IS: 2082 with latest amendment complete and as per site requirement & as per explanatory note. | — | — | — | 2,25,880 | |
| — | 20.00 | — | — | ||
| Supply of PRCD plug 16 A of make Havells, Legrand ,ABB or equivalent & as per explanatory note. | — | — | — | 17,800 | |
| — | 500.00 | — | — | ||
| Fabrication of MS stand/cabinets or any other MS structure of approved drawing for precooling points/battery charger/ covering of electrical structure. The work includes cutting, welding , riveting, nut bolts of the MS structure including applying a primary coat of steel primer and one coat of paint of approved shade & as per explanatory note. | — | — | — | 62,500 | |
| — | 8.00 | — | — | ||
| Supply, fixing, testing & commissioning of LT distribution board surface mounting/flush mounting double door out door type made up of CRCA sheet sheet with anti corrosion treatment and suitable, IP 43 phosphatised powder painted complete with neutral link, earth point, Din rail and prewired confirming to , IEC 60947, 61439 or latest of make ABB, Siemens, L&T, Schneider, Legrand or equivalent with following items of matching make to be fixed in distribution board, confirming to latest relevant IS, IE rules and site requirement. It should be rodent entry proof. It should also include well dressing and coding of circuit & as per explanatory note. 63A 4P RCBO 100 mA= 01 No. (Incoming), 6-32A MCB SP "C" Series =18 Nos. (Outgoing), It should be rodent entry proof. It should also include well dressing and coding of circuit IP2X terminal , reversible door with 180 degree opening, cement spill protection, detachable gland at top and bottom and short link for MCBs. It should also include proper tagging on electrical wires/cables which clearly indicate the incoming point or source and outgoing point of wires/cables. | — | — | — | 86,904 | |
| — | 2.00 | — | — | ||
| Design, Supply, fixing, testing and commissioning of front operated double door type weather proof feeder pillar made of CRCA steel sheet having IP 65 protection (MCCB - Incoming & MCCB - Outgoing) comprising with the following MCCB's fixed in it of make: Siemens, L&T, Schneider, Legrand or equivalent conforming to IEC /IS:13032, IEC 60947, 61439 or latest with digital measuring instrument & bus-bar arrangement and as per latest relevant IS, IE rules and site requirement. It should be dust and vermin proof, conforming to IS 8623 latest version and powder coating as per IS 13871 latest version & as per explanatory note. a) 4P MCCB 400Amps 36 kA with adjustable thermal & fixed magnetic release =01 No. (Incoming). b) 4P 400 Amps on load change over switch (COS)=01 No. c) 4P MCCB 250Amps 36 kA with adjustable thermal & fixed magnetic release = 04 Nos. (Outgoing). d) 4P MCCB 125Amps 36 kA with adjustable thermal & fixed magnetic release = 04 Nos.(Outgoing). | — | — | — | 7,93,354 | |
| — | 1.00 | — | — | ||
| Design, Supply, fixing, testing and commissioning LT panel (ACB - Incoming & MCCB - Outgoing) comprising with the following ACB and MCCBs fixed in it of make ABB, Siemens, L&T, Schneider, Legrand or equivalent conforming to IEC 60947 or latest with digital measuring instrument & copper bus-bar arrangement confirming to IEC/IS 61439 or latest and as per IE rules and site requirement & as per explanatory note. a) 800A ACB 4P with microprocessor MDO type having Breaking capacity 50 KA having Overload, Short-circuit, Instantaneous & Earth-fault protection, with digital display =02 Nos. (Incoming). b) 1600A ACB 4P with microprocessor release MDO type having Breaking capacity 50 KA having Overload, Short-circuit, Instantaneous & Earth- fault protection, with digital display =01 Nos. for (bus coupler). c) 4P MCCB 400Amps 36 KA with adjustable thermal & fixed magnetic release = 02 Nos. (Outgoing) . d) 4P MCCB 250Amps 36 kA with adjustable thermal & fixed magnetic release =08 Nos. (Outgoing). e) 4P MCCB 125 Amps 36 kA with adjustable thermal & fixed magnetic release =04 Nos. (Outgoing). All MCCB in Outgoing circuit will be provided with Extended Rotary Handle and Spreader Terminals - 4 Pole (Set of 8) etc. | — | — | — | 21,97,368 | |
| — | 4.00 | — | — | ||
| Supply, Installation, Testing, Commissioning of 11 KV HT Switch Board ring main 350 MVA 630 A. HT VCB incoming/outgoing type motorized operated panel complete with P.T, digital relays and electro trivector meter, digital power factor meter, digital V-meter, digital A-meter, selector switch, clustered LED type indication lights, double ratio 60/30/5A copper wound current transformer for incoming panel & outgoing ratio 30/15/5A copper wound current transformer for outgoing panel and suitable cable entry box etc. as per actual site requirement & as per explanatory note. | — | — | — | 23,84,820 | |
| — | 900.00 | — | — | ||
| Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation((upto 75-100 cm depth and not less than 35 cm wide), sand cushioning, protective covering and refilling the trench etc. as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest & as per explanatory note. Upto 35 sq. mm | — | — | — | 3,16,800 | |
| — | 2100.00 | — | — | ||
| Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation((upto 75-100 cm depth and not less than 35 cm wide), sand cushioning, protective covering and refilling the trench etc. as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest & as per explanatory note. Above 95 sq. mm and upto 185 sq. mm | — | — | — | 9,80,700 | |
| — | 300.00 | — | — | ||
| Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation(upto 75-100 cm depth and not less than 55 cm wide & maintaining gap not less than 20 cm between the cables), sand cushioning, protective covering and refilling the trench etc as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest & as per explanatory note. Upto 35 sq. mm | — | — | — | 86,400 | |
| — | 700.00 | — | — | ||
| Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation(upto 75-100 cm depth and not less than 55 cm wide & maintaining gap not less than 20 cm between the cables), sand cushioning, protective covering and refilling the trench etc as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest & as per explanatory note. Above 95 sq. mm and upto 185 sq. mm | — | — | — | 2,34,094 | |
| — | 300.00 | — | — | ||
| Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. In case of any demolition of PCC, RCC, road, wall surface etc. the contractor should ensure repairing of the same on own expenses as per site requirement and satisfaction of railway representative conforming to IS 1255 (Reviewed in 2016) or latest & as per explanatory note. Upto 35 sq. mm (clamped with 1mm thick saddle) | — | — | — | 17,700 | |
| — | 700.00 | — | — | ||
| Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. In case of any demolition of PCC, RCC, road, wall surface etc. the contractor should ensure repairing of the same on own expenses as per site requirement and satisfaction of railway representative conforming to IS 1255 (Reviewed in 2016) or latest & as per explanatory note. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) | — | — | — | 1,17,796 | |
| — | 50.00 | — | — | ||
| Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia. including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required & as per explanatory note. | — | — | — | 2,87,550 | |
| — | 250.00 | — | — | ||
| Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) & as per explanatory note. | — | — | — | 38,500 | |
| — | 4.00 | — | — | ||
| Earthing with 600x600x3mm thick copper plate earth electrode as per IS 3043(Latest version), to achieve earth resistance less than one ohm, including construction of masonry enclosure with hinged cover plate of cast iron with locking arrangement (Approx. size 600x600 mm) on top, watering pipe, connections from earth plate to top with 40x6mm copper strip in 50 mm dia. pipe class ' B' provision of earth plate as per drawing & as per explanatory note. | — | — | — | 43,668 | |
| — | 30.00 | — | — | ||
| Supplying and laying 40 mm X 6 mm G.I strip confirming to relevant IS as per IS:3043 (Latest version), fixing on surface or as per site condition, clamping or fixing with suitable arrangement as per site requirement, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm) & as per explanatory note | — | — | — | 58,740 | |
| — | 20.00 | — | — | ||
| Supply, fixing, testing and commissioning of 150-155W LED based flood light luminary with CRI >= 70, SDCM (standard deviation color matching) <5, single housing, side entry, high pressure aluminium die cast/extruded aluminum, IP 66 or better having system complete conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per explanatory Note. | — | — | — | 1,41,000 | |
| — | 250.00 | — | — | ||
| Supply of HDPE pipe of 75 mm dia. Having material grade PE-100, wall thickness PN-6 and confirming to IS-4984:2021 or latest as per IE rules and site requirement & as per explanatory note. | — | — | — | 32,250 | |
| — | 1.00 | — | — | ||
| Supply, installation, testing and commissioning of 2x5 KVA single phase in-single phase out IGBT based with isolator, datalogger, transformer online UPS system conforming to IS 16242 (part1) 2025/IEC 62040-1: 2017 or latest with SMF/VRLA type batter IEC 60896-21 for an autonomy of 120 minutes (70 AH x 15 Nos. x 12V) complete with battery stand as per IS & IE rules and site requirement & as per explanatory note. | — | — | — | 1,54,287 | |
| — | 10.00 | — | — | ||
| Supply of 9 fins oil filled room heater having wattage 2400 watts conforming to IS: 302-2-30:2007, air deliver 50 cubic meter per hour & as per explanatory note. | — | — | — | 93,850 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
SpecialConditionsofContract_1.pdf
ATTACHMENT
GCC-2022-ACS10_merged.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo.11.pdf GCC ACS No 11
ATTACHMENT
TECHSPEC-I.pdf
ATTACHMENT
TECHSPEC-II.pdf
ATTACHMENT
ExplanatoryNote.pdf
ATTACHMENT
TenderDocument.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipNo.11.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .