REPAIRS TO GALVALUME SHEET CGI SHEET ROLLING SHUTTER VALLEY GUTTERS AND REPAIRS TO INTERNAL PERIODICAL PLUMBING FALSE CEILING JOINERY AND OTHER MISC WKS AT OTM ACCN AND AT OD SHAKURBASTI AND HIRANKUDNA IN AOR OF AGE BR II UNDER GE NORTH DELHI CANTT

Amount

M&L for preparation of old decorated plastered or unplastered surfaces of wall and applying one coats of oil bound distemper including preparation of old surfaces by brooming down or steel wire brushing , scraping down smoke suit , moulds, moss,efflorancr salt , trading oil and greasy spot complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered surfaces of wall and applying two coats of oil bound distemper including preparation of old surfaces by brooming down or steel wire brushing , scraping down smoke suit , moulds,filling gaps wth wall care putty, complete all as specified and directed.

M&L for preparation of old decorated previously treated surfaces of wall by brooming down scrapping down smoke and efflorescent salts etc and applying one coat of white wash on walls complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated previously treated surfaces of ceiling by brooming down scrapping down smoke and efflorescent etc. complete and applying one coat of white wash complete all as specified and directed.

M&L for one coats of synthetic enamel paint on old steel painted surfaces including preparation of surfaces of any description not otherwise descriped over 10 cm width or grith complete all as specified and directed.

M&L for one coats of synthetic enamel paint on old wooden painted surfaces including preparation of surfaces of any description not otherwise descriped over 10 cm width or grith complete all as specified and directed.

M&L for ready mix plaster of 15mm thick on brick or conc surfaces in wall (External surfaces) incl necessary cement slurry with builk density 1.40 to 1.70 kg, water ratio 17 to 19% by weight & compressive strength as per IS 4031 part 6 applied as per manufacturer instruction including taking down cement plaster on brick or stone walls/ etc including raking out joints, hacking for key, scrubing down with water etc complete all as specified and directed (Make Ultratech readiplast/ Birla Aerocon RMP/ ACC Suraksha RMP)

M&L for ready mix plaster of 10mm thick on brick or conc surfaces in wall (Internal surfaces)incl necessary cement slurry with builk density 1.40 to 1.70 kg, water ratio 17 to 19% by weight & compressive strength as per IS 4031 part 6 applied as per manufacturer instruction including taking down cement plaster on brick or stone walls/ etc including raking out joints, hacking for key, scrubing down with water etc complete all as specified and directed (Make Ultratech readiplast/ Birla Aerocon RMP/ ACC Suraksha RMP)

M&L for ready mix plaster of 15mm thick on ceiling concrete surfaces incl necessary cement slurry with builk density 1.40 to 1.70 kg, water ratio 17 to 19% by weight & compressive strength as per IS 4031 part 6 applied as per manufacturer instruction including taking down cement plaster on brick or stone walls/ etc including raking out joints, hacking for key, scrubing down with water etc complete all as specified and directed (Make Ultratech readiplast/ Birla Aerocon RMP/ ACC Suraksha RMP)

M&L preparation of newly plastered surface on walls and applying two coat of Oil Bound Distemper over a coat of primer and Putty complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M/L for preparation of newly plastered surfaces of any description and applying two coats of cement base paint over a coat of primer all as specified and directed.

M&L for preparing newly plastered surfaces of ceilling and applying three coats of white wash complete all as specified and directed.

S&F, 3 mm thk sheet frosted glass ordinary quality and galzing with oil putty/wooden/aluminium beads in square n.exc 0.5 sqm each complete all as specified and directed.

Supply and fixing 3mm thick ordinary sheet glass and glazing with oil putty complete in squares not exc 0.50 Sqm each pane incl hacking out complete all as specified and as directed.

M&L non skid ceramic tiles colored tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,in floor etc set and jointed in neat cement slurry and pointed in colour cement laid over and including 15mm thick cement mortar screed bed in CM (1:6) including dismantling complete all as specified and directed.

M&L Viterified ceramic tiles 10 mm thick square/rectangular light shade texture polished,area of each tiles Not exceeding 0.36 sqm,in floor etcb set and jointed with neat cement slurry and pointed with white cement mixed with pigment to match the colour of the tile including 15mm thick cement mortar screed bed in CM (1:6) including dismantling complete all as specified and directed.

M&L Viterified ceramic tiles 10 mm thick square/rectangular light shade texture polished area in vertical surfaces as skirting/dado of each tiles Not exceeding 0.36 sqm,in floor etcb set and jointed with neat cement slurry and pointed with white cement mixed with pigment to match the colour of the tile including 15mm thick cement mortar screed bed in CM (1:4) including dismantling complete all as specified and directed. complete all as specified and directed.

M&L glazed ceramic coloured tiles size 450x300x7mm/350x250xmm thick in walls etc set and jointed in neat cement slurry and pointed in colour cement laid over 10mm thick rendering in CM (1:4) including dismantling complete all as specified and directed.

M&L 15mm bore GI tubing medium grade with all fittings and fixed, including taking up or down steel water tubing and connections and removal from site 15mm bore pipe and complete to walls, ceiling or laid in floor all as specified.

M&L 15mm bore GI tubing medium grade with all fittings and fixed, including taking up or down steel water tubing and connections and removal from site 20mm bore pipe and complete to walls, ceiling or laid in floor all as specified.

M&L for Cutting chases, pinning in Brick walls making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and ctting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed.

S & F in repair fancy type chromium plated bib taps 15mm bore with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed all as directed and specified

S & F in repair angular stop cock, chromium plated, cast copper alloy C.P 15mm bore screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union all as directed and specified.

S & F in repair stop cock, chromium plated, cast copper alloy C.P 15mm bore screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union all as directed and specified.

S&F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with clamps etc including taking out/dismantling of old pipes complete all as specified.

All as per item No above but bore of pipe in 110 mm.

S&F in repair PVC (SWR) bends any radius bore 75 mm

All as per item No. above but bore of pipe in 110 mm.

S&F in replacement of broken cast iron (sand cast) soil, waste and vent pipes in any length, with or without ears, with cement joints, fixed to walls with clamps etc, bore of pipe 75mm complete all as specified and directed.

S&F in replacement of broken cast iron (sand cast) soil, waste and vent pipes in any length, with or without ears, with cement joints, fixed to walls with clamps etc, bore of pipe 100mm complete all as specified and directed.

S&F cast iron bends (sand cast) (any radius), diminishing pieces or tapers soil/waste pipes 75mm in any length (larger bore measured) complete all as specified and directed.

All as per item No. above but 100mm dia

S&F 75mm cast iron branch pieces,double (equal or unequal),ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors as in door 'T', door bends, 'Y' section complete all as specified and directed.

S&F 100mm cast iron branch pieces,double (equal or unequal),ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors as in door 'T', door bends, 'Y' section complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered surfaces of wall and applying one or more coat of plastic emulsion paint including preparation of old surfaces by brooming down or steel wire brushing , scraping down smoke suit , moulds, moss,efflorancr salt , trading oil and greasy spot complete all as specified and directed.

Taking down chowkhats or frames with shutters n.exc 1.5 sqm each(without taking off shutters from the frame) and all as directed.

Ditto as per item above but exc 1.5 sqm but n.exc 4sqm each

Taking down shutters of any description exc 1sqm but not exc 2 sqm each and all as directed.

Taking down shutters of any description exc 2 sqm each and all as directed.

S&F framed work as in doors or gates of angle or other section with gusset plates,rails,braces, etc.,complete drilled for fixing of steel sheeting in or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete, confirming; Fe 410-W. all as specified and directed

S & F aluminium powder coated three track window ( two shutters glazed & one shutters wire gauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber beading joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below :-- (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 21447) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 21446) (c) Top & side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.50 (Section No 21455) (d) Interlock Section of Shutter shall be be of size 18.00 x 40.00 x 1.50 (Section No 21454) (e) Bottom Members of shutter Section shall be be of size 18.00 x 40.00 x 1.50 (Section No 20844) Note:-(i) Section Number given above are of make Jindal, Contractor may use similar section of other make mention in Appx .

M&L for powder coated aluminium grill in repairs of powder coating of minimum 50 micron with aluminium mesh of sze 50x50mm with square tube solid 6mm thick including aluminium channel of size thickness of channel 1.5mm complete all as specified and directed.

S&F MS square bars as in window guard bars welded to steel window frame or fixed to wooden frame all as specified and directed.

Supply and fix 35mm thick, second class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc with rails and styles including cut and mitered beards for securing wire cloth etc,all as specified and directed.

S&F 30 mm Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed.

M/L preparation of new wooden surfaces of any description over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of primer all as directed and specified.

Material and labour preparation of new steel surfaces of any description over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

S&F factory made solid panel PVC door shuter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails & MS frame shall be covered with heat moulded plain colour PVC `C” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement of stiles and plain colour PVC sheets for top rail,lock rail & bottom rail, on either side & as gap insert for top rail & bottom rail & panelling of plain colour PVC sheet to be fitted in the MS frame welded/Sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per complete all as specified.

S&F solid door frame 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete.all as specified and directed.

S & F 100mm medium weight stainless steel butt hinges complete all as specified

S&F aluminium anodised barrel tower bolt 200mm long extruded section all as specified.

S&F 250mm long aluminium alloy anodised sliding bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts and extruded section or cast aluminium alloy and fixed complete.

S&F 150mm size extruded aluminium handles fabricated type anodised complete all as specified.

S&Fix in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks/stainless steel wire staples all as specified.

Complete removal of old roof treatment incuding cement mortar ( except mudfushka , brick tile ) and removal of grass, small trees by picking sweeping , cleaning and washing down with water to remove dust etc incuding removing debries out side MOD land , complete all as specified and directed.

M&L for 15 mm thick cement plaster over the concrete / brick roof surfaces in cement mortar 1:4 mixed with liquid water proofing compound @ 200ml per bag WPC (liquid type) , surface finished even and smooth without using extra cement all as specified and directed. Note :- Water proofing additive shall be measured and paid separately.

M & L for applying a priming coat of @ 0.30 Kg / Sqm with Bituminous primer including prepration of surface , complete all as specified and directed .

M & L for applying evenly a tack coat of industrial hot blown grade bituminen 85/25 @ 1.2 Kg/Sqm including cleaning surfaces over primer ,complete all as specified and directed.

M & L for water proofing treatment of roof with APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) shall be laid with 100mm side lap/end lap on primed surfaces as per manufacturers instruction , complete all as specified and directed.

M& L for applying a coat of heat resisting paint ( aluminium bitumen paint) over APP surface, complete all as specified and directed .

Disconnecting existing overhead tanks,setting aside or lowered if required for repairing ,cleaning etc and hoisting if reqd reconnecting and refixing in position but capacity exceeding 250 litres and not exc 500 litres complete all as specified & directed.

Disconnecting existing overhead tanks,setting aside or lowered if required for repairing ,cleaning etc and hoisting if reqd reconnecting and refixing in position but capacity exceeding 500 litres and not exc 1000 litres complete all as specified & directed.

Cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismentled portion in CM 1:3 or cement concrete 1:2:4 type B-I as required, Exc half brick but not exc one brick wall.

M&L for PCC1:2:4 Type B-0 ( 12.5 mm graded aggregate) cement concrete in roof padding,roof kerbs of mud stops, rounded or chamfered on edges complete all as spcified and directed.

Supply only Integral water proofing compound complete all as spcified and directed.

Demolition of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and directed

Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section unframed work complete all as specified and directed

Dismantling of timber scantlings, of framed work, from any position & height 40 Sq.cm and over in section complete all as specified and directed..

M/L exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 x 600mm grid 6mm thick complete all as specified and directed by Engr-in-Charge. (Note : frame work for ceiling shall be measured and paid separately)

M&L Anodised aluminum snap grid frame work of size 605x605mm for false ceiling including hanger 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3mm size 60mm long with complete hanging arrangement and making good at surface all as specified and directed

S&F box type mild steel windows glazed / gauzed incl frame made of hollow sections 60 x 25 x 1.25 mm thick 50 x 20 mm x 1.25 mm thick MS Hollow pipes as in windows shutter with or with out sash bars incl 150 mm size MS tower bolts 2 No each leaf, MS handle made of Z section 100 mm long 2 Nos each leaf, mild steel cheat 55 mm x 25 mm x 75 mm long 2 Nos each leaf, mild steel cleat 55 mm x 25 mm x 75 mm long, MS Pintel hing 75 mm long 14 mm dia 02 Nos each leaf complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

Demolition of cement concrete of any description and in any position(unreinforced) in ground floors below or above ground level n.exc 15 cm thick and clearing rubbish from site all as directed and specified.

M&L for 40 mm thick Cement concrete 1:2:4 type B-0 as in floor including surfaces to be finished even and smooth with using extra cement complete all as specified and directed

M&L for Glass dividing strips, 3mm thick and 38 mm wide complete all as specified and directed

M & L 75 mm thick Cement concrete 1:3:6 (40mm graded aggregate) in flooring or plinth protection including surfaces to be finished even and smooth without using extra cement complete all as specified and directed.

Demolition of brick work built in cement mortar in any position including all quions, arches and pillars etc, complete all as specified and directed.

M&L for brick work masonry with sub class 'B' brick straight orcurved on plan exceeding 6 mtr radius built in cement mortar 1:6 complete all as specified and directed.

M&L Welding in repairs n. exc 6mm thick metal and n. exc 2.5 cm in length all as specified and directed..

Dismantling loose concrete cover of RCC coloums, beams, slabs, Chajjas (Soffit only), and the like as directed, roughening and cleaning concrete surfaces with steel wire brushes, washed with water and allowed to dry, including dusting of steel reinforcement, providing fabric mild steel wire mesh 75 mm x 75 mm of 2 mm dia as reinforcement to concrete surfaces, applying adhesive/admixture over steel mesh and providing 25 mm thick (average thickness) guniting mix (using 1 part of ordinary portland cement 53 grade and 2 parts of ghaggar sand mixed with adhesive/admixture at the rate as per manufacturers instruction or 3% by wt of cement all as directed with a pressure of 2 to 2.5 kgs per sqm by guniting machine and surfaces finished even and fair, including 15mm thick plaster in cement mortar 1:4, necessary padding, steel scaffolding and shuttering for working platformm/formwork etc complete all as directed (Guniting work is to be carried out upto 06 mtr height from ground level). Notes :- (i) Plycrete admixture shall be procured from Chemical Adhesive Pvt Ltd Co. or their authorized dealer.

Repair of Aluminium door shutters with chowkhats area exc. 1.5 sqm but n.exc 3.00 sqm taking down, re-setting easing fixing of cleats screws nut , bolts, fixing of hold fasts, fixing of Aluminium door stopper, change of PVC rubber beadings, complete repair for smooth functioning of door all as specified and directed.

Supply and fix door closer hydraulically regulated,of aluminium(Die cast) body universal type suitable for door shutters 851 to 1000mmin width and weight between 38 to 60kg of Hydraulic door closer complete all as specified and directed.

S&F aluminium door shutter with frame100X45X1.5mm powder coated fixed to wall with steel fastnes min four number each side partly glazed with 5 mm thick tinted glass and partly panelled with 8mm thick coloured aluminium composit panels incl rubber beading, joining cleat for fixing in position, 2 numbers aluminium door handle 250 mm long, 1 number aluminium barrel tower bolt 200 mm long ,1 number aluminium floor door spring & one No 4 liver mortice lock of Godrej of size 100 mm in each shutter will be provided all as specified and directed as per following specifications -- (a) Vertical Members of shutter (Style) Section shall be of size 85.00 x 44.45 x 1.50 mm (Section No 19560) (b) Top rail ( Top Members) of shutter Section shall be of size 85.00 x 44.45 x 1.50 mm (Section No 19581) (c) Lock rail (Middle member) of shutter Section shall be of size 150.00 x 44.45 x 1.50 mm (Section No 19596) (d) Bottom rail ( Bottom Members) of shutter Section shall be of size 150.00 x 44.45 x 1.50 mm (Section No 19584) (e) Glazing clip for securing glass of shutters shall be of 0.80 mm thick (Section No 19370). Standered quality rubber beading shall be used for securing of glass (f) Top, Bottom and verticle member of shuttert will be tightened with hexagonal nut and purpusly made bolt of 10mm dia MS round bar threaded on both the end . Note:-(i) Section Number given above are of make Jindal, Contractor may use similar section of other make mention in Appx B.

Taking down rolling shutters of any description and size including anchoring rod, top cover and all fittings complete, including making good the disturbed portion Complete all as per specified and directed.

S & F steel rolling shutters, without ball bearings 1.00 mm thickness of lath including top cover, anchoring rod, hasp and staple including one shop coat primer, erected in position, gear operated type with bevel gear box and crank handle as indicated. Complete all as per specified and directed.

S&F Ball bearings for rolling shutters complete all as specified and directed.

S&F for Safety lever locks mild steel with 4 levers for rolling shutters.

S & F plain mild steel black sheets 1.25 mm thick covering to steel doors cut to size with plain 40 mm lap joints or welded/riveted seams including bending, turning up etc. Complete all as per specified and directed.

Taking down rolling shutters of any description and size including top cover, cleaning the helical wire spring, anchoring rod, guide channels etc and greasing /oiling to all moving parts of rolling shutter including straighting the anchoring rod, braket plate for smooth functioning, replacement of damaged/worn out lath 1.25 mm thick and re-fixing the rolling shutter with top cover and making good the disturbed portion etc. complete all as directed and specified. (NOTE 1 :- The unit quoted rate deemed to be included for minor repairs , welding and replacements of nut & bolts if required. NOTE 2 :- Material Like helical wire spring, anchoring rod, gear box, etc shall be measured and paid in following item given below.)

Supply only mild steel helical wire spring 45 cm long, 75 mm dia and weighing of each spring not to be less than 2.40 kg. Complete all as per specified and directed.

Supply only mild steel tube medium grade of 40 mm dia for anchoring rod to rolling shutter including necessary weding to M.S. bracket plate, drilling holes for fixing spring. Complete all as per specified and directed.

Supply only mild steel lock plate and handle made out of MS flat iron, including necessary welding. Complete all as per specified and directed.

Supply only gear box full set including realignment of connecting rod. Complete all as per specified and directed.

Supply only MS gear assembly including connecting and fixing the gear box to wall with two numbers hexogonal bolts 10 mm dia. Complete all as per specified and directed.

Supply only 1.00 mm thick laths in any type of rolling shutters and in any length including all necessary work for satisfactoringly functioning of rolling shutter complete all as specified and directed.

Supply only Mild Steel ,laths 1.25 mm thick in any type of sliding shutters and in any length including all necessary work for satisfactry functioning of sliding shutter complete all as specified and directed.

Supply only guide channel, rails, angle etc for smooth functioning of sliding shutter including necessary welding to M.S. bracket plate, drilling holes for fixing complete all as directed and specified.

Repairs to Steel gates (including Sliding door) , re-setting easing fixing of cleats screws nut , bolts, fixing of hold fasts, fixing of door stopper, greasing, complete repair for smooth functioning of door by all necessary means (welding angles, flats etc) including all the additional material added to make the gate functional all as specified and directed. Note: Steel gates are heavy and large, so contractor should make necessary safety measures while repairing the doors.

Dismantaling corrugated, semi corrugated AC sheeting etc any gauge, thickness, or similar pattern roof covering all as specified and directed..

Dismantling Plain or corrugated steel sheeting, any guage, thockness, including Nainital or similar pattern roof covering all as specified and directed.

S&F 6mm thick asbestos cement, corrugated or semi-corrugated shets in roofs, walls, with 'L' or 'J' type hooks etc all as specified and directed. Note: Hieght of building/ shed is upto 12mtr. Contractor will provide safety arrangements.

M&L Asbestos cement serrated ridge for corrugated or semi corrugated sheets fixed wth L-type or J-type or cranked hooked bolts all as specified and directed.

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of sky blue/ sea green colour having tensile strength of 550 MPa as in roof covering, fixed with self tapping screws/ J hooks if required complete all as specified and directed.

S&F Plain, galvanised, mild steel sheeting 2mm thick, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 incl nessary welding ,screwing, bending etc complete all as specified and directed by Engr-in-Charge. Note: Hieght of building/ shed is upto 12mtr. Contractor will provide safety arrangements.

S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, ridges, velly gutters fixed with self tapping screws complete incl dismantling of old AC Sheets all as specified and directed. Note: Hieght of building/ shed is upto 12mtr. Contractor will provide safety arrangements.

M&L dismantling structural steel work including doors, gates etc.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe -290 (Gde E-165) complete all as specified.

S & F MS plates (plain or chequered) channels, square cut or notched ordinary and counter sunk) forming holes, without any attachment confirming to Fe -290 (Gde E-165) complete all as specified.

M&L for mild steel nut and bolts dia of neck exc 12mm but not exc 20mm purpose made, with hexagonal or square head one end and screwed the other, or screwed bot ends, each screwed end to be fitted with washers and one hexagonal or square nut. Exv 30 cm long all as specified and directed.

M&L cement concrete type B0 (1:2:4) using 12.5 mm graded aggregate as in coping, bed blocks, kneelers, apex stones, bed plates, kerbs including bending, weathering, slightly rounded or chamfered on edges complete all as specified and directed.

M/L PCC 1:2:4, type B2 using 40mm grade stone agg as in foundation fixing all as specified and directed.

Excavation in post holes (or similar holes) each n.exc 0.5 cum and getting out in soft/loose soil complete all as specified.

Schedule of Credit- 1,07,905.00

SARTHEE CONSTRUCTION CO.

QUALITY CONSTRUCTIONS CO

S GOURAV PRAKASH ENTERPRISES

The new hut furnitures

SHRI JI ENTERPRISES