SPL REPAIR TO BLDG NO P 38 MD ACCN AT TENALI AREA AND PROVN OF 01 X SOAKAGE WELL AND SEPTIC TANK NEAR BLDG NO P 79 AT DINJAN MIL STN UNDER GE DINJAN

Amount

Demolition of cement concrete s reinforced (reinforcement cut as required to facilitate demolition) Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter all as specified and directed.

Formwork to soffits of suspended slabs flat such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc all as specified and directed.

M&L for RCC (Nominal Mix) type Bo 1:2:4 (12.5 mm graded aggregate) for Chajjas, Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc all as specified and directed.

M&L for RCC (Nominal Mix) type Bo 1:2:4 (20mm graded aggregate)Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

All as per item No 6 here-in-before but TMT bars 5mm dia over and upto and including as in stirrups all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n exc 15cm thickness (below or above ground level) all as specified and directed.

M & L PCC 75mm thick 1:3:6 type C-2 thick ( 40mm graded aggregate) thick as in plinth protection finishing cement concrete surface even & fair whthout using extra cement complete all as specified and directed.

Dismantling water tanks and removing to store Exc 500 & n.exc 1000 Ltrs all as specified and directed.

S&F 500 Ltrs rotational moulded polythelene water storage tanks (Cylinderical vertical with closed top) hoisted and fixed in position including 15mm bore ball brass valves high pressure, with polythene float & fly nuts complete all as specified

S&F 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed.

Taking down chowkhats or frames with shutter (without taking off shutter from the frame)exe 1.50 but n. exc. 4 sqm in each complete all as specified & directed.

Taking down chowkhats or frames with shutter (without taking off shutter from the frame) n. exe 1.50 sqm in each complete all as specified & directed.

S&F Pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and as directed.

S&F Pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and as directed.

S&F 35 mm thick, 2nd class hardwood plain, factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, stainless steel gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

M & L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length all as specified & directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face)& 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureFactory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed.

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; but wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly complete all as specified and directed.

S&F 100 mm size, butt hinges, extruded medium weight cold rolled mild steel etc complete.

S&F 150mm size, aluminium anodised handle, fabricated type.

S&F 100mm size, aluminium anodised handle, fabricated type.

M&L 150 mm long mild steel, barrel tower bolts of extruded section etc complete.

M&L 100 mm long mild steel, barrel tower bolts of extruded section etc complete.

S&F Mild steel sliding door bolts,250mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed

S & F in repairs 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

S&F in repairs curtain rails, mild steel, aluminium alloy chromium plated with fixing brackets, stops, rollers etc

S&F powder coating Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified including powder coating of minimum 50 micron thickness.

S&F Powder coating anodised aluminium window and ventilator shutters 2-3mm thick, side hung type without sash, aluminium sectiion weighihg 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber e packing, anodised handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc, complete all as specified.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sq.m. each pane .

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples.

S&F floor door stopper 150mm long of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in doors.

Demolition and breaking up100mm drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

S&F 110mm PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls complete as specified and directed.

S&F 110mm PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches complete as specified and directed.

S&F 110mm bore PVC (SWR) bends of any radius complete as specified and directed.

S&F 75mm PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls complete as specified and directed.

S&F 75mm PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches complete as specified and directed.

S&F PVC (SWR) junction, single T equal or unequal 110mm bore.

S&F PVC (SWR) 75 mm dia, floor trap ,plain with grating including jointing to waste pipe with solvent cement and fixing in PCC 1:2:4.

S&F 110mm bore PVC (SWR) vent cvowl.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

M&L for Cutting out cracks to V-section in existing terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight).

S&F for APP based polymeric membrane minimum weighing 3Kg/sam and minimum 3mm thick reinforced with polyster non wove fabric (wt, not less than 150 gms/sqm) land on primed surfacfe by forced application complete all as specified.

M&L for Bitumen blown any grade, applied hot, two cfoats, to concrete surfaces at the rate of 1.5 Kg per Sq. m. per coat.

M&L for 25mm thick cement concrete type C-2 , 1:2:4 (20mm graded aggregate) finishing surfaces even and smooth without using extra cement.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with puttty or fixed with beads,

Demolition of cement concrete (unreinforced) Concrete of any description and in any position not otherwise specifically provided for

M&L of Cement concrete type C2 1:3:6 (40mm graded aggregate) as in surface channels and drains

M&L Extra for forming fair finishing to drains or channel of 30 cm inner girth in cement concrete with using extra cement including forms, moulds, mitred/stopped ends etc

Demolition of brick work built in cement morter as specified and as directed

M & L Brick work with sub class 'B' brick, in half brick thick wall, built in CM (1:4) complete all as specified and directed.

M & L Brick work with sub class 'B' brick, staright or curved or plain exc 6 m mean radius built in CM (1:6) complete all as specified and directed.

Taking down cement plaster on brick or stone or concrete surfaces of wall etc , icluding raking out joints , hacking for key, scrubbing down with water etc.

M&L for rendering 10mm thick on fair face of brick works or concrete surfaces of walls with CM (1:4) anf finished even and smooth without using extra cement.

M&L for rendering 5mm thick in ceilings of concrete surfaces with CM (1:3) anf finished even and smooth without using extra cement.

M & L for rendering 15mm thick on other thanfair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with integral water proofing compound weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. ( Note : WPC shall be measured and paid separately)

Supply only water proofing compound for external plaster. (Make : Sika/Cico).

M&L for preparation newly plaster surfaces of wall, chajja facia etc with putty 1-2mm thick and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/litre and UV resistant as per IS-15489=2004 alkali and fungal resistant exterior paint of required shed (company depot limited) with silicon additives 1/43 litres/10 Sqm over and including primer applied 0.90 litres/.10 sqm over new surfaces using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 Mtr, the spray machine whould be of reputed manufacturer with pro guaeds technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and acessories complete all as specified and directed.

M&L for Complete removal of existing treatment and treating from walls and applying 1-2mm thick wall putty and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new plastered surface even and smooth complete all as specified and directed

M&L for preparing of new plastered surfaces of walls & applying white primer including applying plaster of paris putty of 1 -2 mm thickness over plastered surface to prepare the surface even and smooth etc and applying two coats of oil bound distemper etc complete all as specified and directed by Engr-in-charge.

M&L for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-charge.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash over a coat over a coat of white primer etc complete all as specified and directed by Engr-in-charge.

M&L for complete removal of old plastered surfaces of ceiling and applying three coats of white wash etc complete all as specified and directed by Engr-in-charge.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation all as specified.

M&L for machine pressed concrete coloured and polished interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 Grade with grey cement and pigment.

M&L for Providing, cement concrete 1:2:4 type B0 (12.5 mm graded aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges o, in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed.

M&L 15 mm thick, screed bed or bedding layer of cement mortar 1:6, for laying floor finishes as directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles all as specified and directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles all as specified and directed.

M&L rendering 10mm thick in cement mortar (1:3) on fair faces of brick work or concrete surfaces as in vertical surfaces for laying tiles as directed.

M&L Glazed ceramic tiles in vertical surface 450x 300x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the shade of tiles all as specified and directed.

M&L of Machine cut kota stone slab flooring 22 mm thick over and including 15mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L of Machine cut Kota stone slab 22 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick cement screed in CM 1:4 and jointed with j grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Dismantling wall and celling board (fibre, pulp, insulation etc) any thickness including cover fillets as directed.

S&F 605x605mm Anodised aluminium snap grid frame work for false ceiliong all as speecified.

S&F Hangers 6mm dia G.I (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilinhg cleats made out of G.I. flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

M&L for 6mm thick high pressutre, oceanic pre-primed, self embossed, non-asbestos fibre cement decorative board , water, termite and fire resistant for insulatrion and acoustic piurpose fixed or laiod/inserted to timber/GI/Aluminium framework with screws complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings roof coverings.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ as in ridge, fixed with ixed with self tapping screws as specified.

S&F 1mm Thick 150mm dia Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges

Taking up or down 15 mm bore steel tubing and connections, including removal to store complete all as specified and directed.

Re-fixing 15mm bore old steel tubes,with all fittrings and fixed, to walls and ceilings or laying in floors

S&F steel tubes, galvanised 15 mm bore, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete as specified and directed including taking down old one.

Taking up or down 20 mm bore steel tubing and connections, including removal to store complete all as specified and directed.

Re-fixing 20mm bore old steel tubes,with all fittrings and fixed, to walls and ceilings or laying in floors

S&F steel tubes, galvanised 20 mm bore, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete as specified and directed .

S&F in repairs Vitreous china wash basin, white flat back, size 550mm x 400mm with brackets, excluding pillars cock 15mm bore CP, PVC connection of 450mm long including PVC (HDPE) 32mm bore waste pipe, brass couplings 32mm CP etc complete all as specified and directed.

S&F in repairs 15mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads screwed down high pressure witgh or withoyut lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe as specified.

S&F in repairs, stop valves, 15mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed bhoth ends for iron pipe or for unions as specified and directed.

S&F in repairs 15mm bore PVC connection pipe 450mm longh with PTMT nuts at both ends all as specified and directed.

S&F in repairs, 10 Litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet. Ball valve, float bracket & flush pipe complete all as specified & directed.

S&F in repairs 15mm bore Bib Taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwex for iron pipe or for brass ferrule and fixed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern) with seat cover white with 'P' or 'S' trap, including and flushing pipe etc complete including making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing specifications as specified (excluding fixing bolts, flushing cistern and flush pipe)

S&F in repairs Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern omplete all as specified and as directed.

S&F in repairs 32mm dia Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm?45gms/40mm-60 gms) complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified and directed.

S&F in repairs, Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) all as specified and directed.

M&L for broken stone bolder as hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface as specified and as directed.

S & F for rolled mild steel work in roof trusses (framed), trussed, purlins crane gantries , rafts and fastening and heavy brackets framming (beams tee,angle channel and or flat sections) including distance pieces, cleat nut bolts etc quality confirming to Fe-290 (Gde E-165) as specified and as directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end screwed the other, or screwed both to be fitted with washers and one hexagonal or square nut, not exc 5 cm long coomplete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Excavation over areas not exc 1.5 m deep and getting out in soft / loose soil complete all as specified and as directed.

All as per Item No 115 above but depth exc 1.5 m but not exc 3.0 m complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm thick in soft/loose soil complete all as directed.

Removing excavated surplus soil n. exc 50 m and depositing where directed at level n.exc 1.5 m above the starting point.

M&L plain cement concrete (1:4:8) type D-2 for foundation concrete ( using 40 mm graded agg ) complete all as specified and directed.

M&L plain cement concrete (1:2:4) type B-2 for foundation concrete ( using 40 mm graded agg ) WPC @3% by weight of cement complete. (WPC measured and paid separately) all as specified and directed.

M & L rendering 20 mm thick internally in cement mortor 1:4 on fair faces of brick work or concrete surfaces and finishing the surface even and smooth using extra cement mixed with WPC @3% by weight of cement complete. (WPC measured and paid separately) all as specified and directed.

M&L rendering 10 mm thick externally on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished the surface fair and even without using extra cement mixed with WPC @3% by weight of cement complete as specified and directed. (WPC measured and paid separately) .

M&L for RCC 1:2:4 type B1 ( Nominal Mix ) using 20 mm grade aggregate as in columns ,pillar,piers, posts and struts etc. complete all as specifiedand as directed.

M&L for RCC 1:2:4 type B1 (Nominal Mix) using 20mm graded aggregate in Beam, cantilever, bressummers, lintel over 1.5m span complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B1 using 20 mm grade aggregate as in landing, in cover slab (for manhole etc) and similar article with plain faces set in CM 1:4 complete all as specified and directed.

All as per Item No 6 here-in-before but 6 to 8 mm dia and over cut to length, bent to shape reqd incl cranking , bending spherically for hooping for columns , hooking ends & binding steel wires not less than 0.9mm dia with clips complete all as directed and as specified.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete shape in square, rectangular or polygonal. Complete all as specifies and directed.

Use and waste of form work fin, louvers and facia,bubble wall etc in rough finished surface all as specified and directed.

Use and waste of form work to edges of concrete flat in rough finished surface work exc 10CM and nexc 20 CM complete all as specified and directed.

S&F 75 mm PVC (SWR) vent cowl complete all as specified and as directed.

M&L for loose filling with broken bats of gauge 80 mm to 150 mm in graded in soakage pits, soakage well complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m deep and getting out in soft/loose soil all as specified and directed.

M&L for PCC 1:3:6, type C1, using 20mm graded aggregate as in coping complete all as specified and directed.

S&F SGSW pipe laid in trenches and as specifed for150mm bore of pipes complete all as specified and directed.

M&L for concrete bed to drain pipe in PCC 1:4:8, type D 2 (using 40mm graded aggregate) to 150mm drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested.

M&L for cutting into existing manholes for connecting new drain, making good to pipe rendering, cutting out existing benching for and forming branch channel(1/2 round and 3/4 secton) in cement concrete (1:2:4) type B-1 smooth finished and reforming bencing as required for 150 mm dia complete all as specified to directed.

Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed.

Taking down carefully MCB DBs any type and size by unscrewing from main switch boards/cut out boxes and removing materials to store for keeping in safe custody for reuse at site or for taking credit including sealing the cable ends and making good disturbed surface of wall etc as per existing finishes complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and keeping it in MES store for safe custody and refix it after repair all as specified and directed.

Material and labour for point wiring for the followings with 1.5 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through concealed wiring and including PVC conduit of required size including necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly including sunken type pressed steel terminal boxes of 1.2mm thickness with plastic laminated white top sheet cover 3mm thick for One light/fan point controlled by one,one way switch all as specified & directed. (Note:-(1) Rate for Cutting, chieseling and making good the existing surface for complete concealed wiring is deemed to be included in quoted rate)

Description all as per Ser item No. 140 here-in-before but One bell point controlled by one push button switch.

Description all as per Ser item No. 140 here-in-before but One 3 Pin 5 Amps socket out let point on independent board.

Description all as per Ser item No. 140 here-in-before butOne 3 Pin 5 Amps socket out let point on same board alongwith other suitable switchs.

Description all as per Ser item No. 140 here-in-before but One light point controlled by two, 2 way switch.

Description all as per Ser item No. 140 here-in-before but using 2.5 sqmm PVC FRLSH insulated copper condutor wire for connecting 15A socket on independent board complete all as specified/directed.

Description all as per Ser item No. 140 here-in-before but using 4 sqmm PVC FRLSH insulated copper condutor wire for connecting 15A socket on independent board complete all as specified/directed.

Supply and fixing of switch piano flush type 240 Volts 5 Amps, SP, one way complete all as specifed/directed.

Supply and fixing of switch piano flush type 240 Volts 5 Amps, SP, two way complete all as specifed/directed.

Supply and fixing of bell push piano flush type one way 240 Volts, 5 Amps all as specified/directed.

Supply and fixing of switch socket combination 3/5 Pin, 2 in 1, 5 Amps, 240 volts flush type (non shuttered) complete all as specified/ directed.

Supply & fixing of socket outlet 2 in 1, 3/5 pin 5 Amps, 240 Volts, flush type (non shuttered) complete all as specified / directed.

Supply and fixing of switch socket out let combination multipurpose 3/5 pin, 15/16 Amps and (with 3 pin 5 Amps outlet also) flush type (non shuttered) complete all as specified/directed.

Supply and fixing of bell electric, ding dong type 240 Volts, single pole complete all as specified and directed.

Supply & Fixing of ceiling fan regulator electronic,Deluxe,rotary, step type, 120/280 volts as specified/directed.

Supply and fixing angular/batten holder PVC/Polycarbonate suitable for batten fittings including one inverter LED Lamp of 9W complete all as specified & directed.

Supply and fixing of ceiling rose surface PVC/Polycarbonate, 65x50 mm two to three terminals complete all as specified & directed.

Supply and fixing inverter LED fitting 1x18 watts, 220volts AC decorative box type with driver,holder and aluminium housing with Burning hr of 45000 withLED tube light conncting up to 3 core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F LED light fitting inverter type with high ouput diffuser 2 feet, 10 watts 220 volts AC decorative type with aluminium housing driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable of suitable size.

S&F LED building light fitting 35W 230 volts AC outdoor tye with high pressure die cst aluminium hostng and heat resistant complete with driver, lamp baacket with impact and corrosin resistant including thermal management in multiple optics complete wth IP 65/66 protection completed as directed & specified.

Supply and fixing in repair of MCB Distribution board TPN 4 Way for mounting SPN/ SP/TPN/TP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed at site as specified and directed.

Supply and fixing in repair of MCB Distribution board SPN 8 Way for mounting SPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed.

Supply & fixing in repair 415 Volts 10KA 'C' curve miniature circuit breaker(MCB) TPN 63 AMP in the DB complete with connection testing and commissioning all as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) SPN and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning all as specified and directed.

Supply & fixing in repair of MCB SPN 32 Amps 'C' Series 10 KA 240 volts complete all as specified and directed.

Supply & fixing in repair of MCB SP 6-32 Amps 'C' Series 10 KA, 240 volts complete all as specified and directed.

Material and labour for earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanised wire of dia 4 mm as earthing lead by means of nuts, bolts and washers of galvanised iron and earth lead protected by galvanised iron pipe 15 mm bore (light grade) and connected to earth test point and including cement concrete pit in PCC (1:3:6) type C-1(using 20 mm graded aggregate) and pre-cast RCC cover slab of size 540 x 540 x 50 mm thick, reinforced with 8 mm dia TMT bars both ways and one handle for lifting made with 10 mm dia mild steel bar,funnel, wire mesh 20 mm bore galvanised (light grade) for watering, charcoal and salt in alternate layers including necessary execuation and eath works in any types of soil complete all as shown on Electrical plate No 3 of MES SSR-I including taking out the old earthing material complete all as specified and directed.Note:No extra payment will be for the earthing GI wire of size 4 mm dia all complete as specified and as directed.

Taking down old unsv submain wiring and Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC conduit of adequate size fixed on surface of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 6 Sqmm as earth wire (green in colour) run through PVC Conduit and connected common earth dolly including taking out the old sub main wiring for connection to DBs/dolly shall be deemed to be included in this item and Two runs of 6 Sq mm as current carrying conductor and one run of 6 Sq mm as earth conductor PVC conduit shall be measured as one run for measurement, complete all as specified and directed.

Taking down old unsv cable and Supply and laying and testing cable, XLPE insulated,screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables(heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 sq mm 3½ core all as specified and directed.

Excavating in Trenches not exc. 1.50 mtr wide and not exc. 1.50 mtr in depth, Taking Out and Laying of Cables, etc. and getting out in Soft/ Loose Soil, complete all as specified and as directed.

M&L Sand Cushioning (dry) in Trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thick -ness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed.

S&F Type-1 flat-1 size 250 x 150 x 40mm for cable protection cover, well burnt all size bricks, laid breadth-wise along the axis of Cable laid in Trenches over Sand Cushion laid for UG Cable Protection, complete all as specified and as directed.

Boring under without disturbing the top surface of the road for passing through GI protection pipe 50mm bore, not exceeding 10m in single length complete all as specified and as directed. Note: Necessary infrastructure required for boring shall be arranged by the contractor at his own cost.

FREEZCON (BID ID -3418217)