Construction of Sakhi One Stop Centre Building at Solan Distt. Solan (HP).

Amount

Excavation in foundation, trenches etc. in earth work in all kind of soil lifts upto 1.50 mtr and stacking the excavated soil not more than 3mtrs. Clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinths sides of foundation etc. consolidating each deposited layer by ramming & watering and then disposing of all the surplus excavated earth as directed within all leads and lifts disposed earth to be levelled neatly dressed including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:4:8 (1cement:4sand:8graded stone agregate 40mm nominal size ) and curring complete excluding cost of form work in foundation and plinth including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Stone soling prperly handpacked filling interstices with kharnja stone & consolidated properly complete in all repsect including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing form work with steel plates 3.15mm thick weled with angle iron in frame 30x30x5mm so as to give a fair finish including levelling centering, shuttering strutting and propping etc. With wooden battens and ballies, hight of propping and cenring below supporting floor to ceiling in all heights and removal of the same for in-stu reinforced concrete and plain concrete work in including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. :- a) Foundation, footing bases of colums etc. and mass concrete.

b) Columns, pillars, post and struts, square, rectangular or polygonal in plain.

c) Beams, cantilevers, girders & lintels, sides & soffits or beams, beam haunchings, cantilvers bressumers and lintels not exceeding 1mtrs in depth.

d) Flat surfaces such as soffits of suspended floors, roofs, landing of the like floors etc. upto 200mm in thickness.

e) Stair cases with slopping or stepped soffits excluding landing.

f) Vertical surfacessuch as walls.

Providing & laying reinfirced cement concrete work 1:1.5:3 (1cement: 1.5sand: 3 well graded stone aggregate 20mm nominal size) proportionally by weight with 43 grade cement @ 400 kg/cum minimum M-20 grade and curing complete excluding cost of form work and reinforcement for reinforced concrete work in all height as per HPPWD specifications with updated BIS norms. (a) Foundation footing bases of columns etc. and mass concrete.

b) Columns, pilasrs, posts and struts, square, rectangular or polygonal in plain.

c) Suspending floors roofs landing & shelves and their supports, balconies, beams, girders, bressumers and cantilevers

d) Stair cases (except spiral staircases) excluding landing but prepairing of the surface and finishing of nosing upto all floor levels.

e) Walls (any thickness) attached pilasters, butresses, plinth and string courses etc. From top of foundation level upto all floor levels.

Providing and laying upto first floor two level reinforced cement concrete 1:2:4 (1 cement : 2 Sand : 4 graded stone aggregate 20mm nominal size) to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in Mouldings as in cornices windows, sills etc. not exceeding 15cm in girth including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing tor steel reinforcement (Fe 415/ Fe-500 D as per design) for RCC work including bending, binding and placing in postion complete upto all floor levels including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Brick work using common clay burnt building bricks in superstructure above ground level in cement mortar 1:6 (1cement: 6 sand) 1st class bricks upto all height including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Half brick thick Honey comb brick work with common burnt clay building bricks in cement mortar 1:4(1cement:4 sand) 1st class bricks including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Half brick masonry in comman burnt clay building bricks in superstructure above plinth level upto floor two level with cement mortar 1:4(1cement:4 sand) 1st class bricks including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing Powder coated anodized aluminium work for doors windows, vantilators and partition with extruded build up standerd tubular and other section of approved make conforing to IS 733 & IS 1285 anodized transparent or dyed to required shade. Sealing all the Gaps with Silicon. (a) For doors, windows, ventilator & glazed partition frame including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

b) For shutters of doors and windows.

Providing and fixing Aluminium Partition Panel for partitioning/cubboard shutters/ door shutters etc. exterior/interior grade excluding frame work 4mm thick.including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Supplying and fixing of Glass panes 5mm thick with beading and nails complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing anodized aluminium sliding door bolt anodized transparent or dyed to required colour and shade with bolts and nuts screws etc. complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. (a) 300x16mm.

Providing and fixing aluminium tower bolts (barrel type ) anodized transparent or dyed to required colour and shade with bolts and nuts screws etc. complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. (a) 200x10mm.

Providing and fixing aluminium handle anodized transparent or dyed to required colour and shade with nacessry screws etc. complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. (a)125mm.

Providing and fixing oxidized M.S. hooks and eyes 150mm including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture (conforming to IS 6315) for aluminium door including cost of cutting floor as required embedding in floors and cover plates etc. complete as per the direction of Engineer-In-Charge I/c making good the floors.

6mm cement plaster in ceiling with cement mortar 1:4(1cement:4 sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastring upto all floor levels including arrrises, internal rounded angles, chamfers and/or rounded angle not exceeding 80mm in girth and finished evehn and smooth in cement mortar 1:6(1cement :6sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastring upto all floor levels including arrrises, internal rounded angles, chamfers and/or rounded angle not exceeding 80mm in girth and finished evehn and smooth in cement mortar 1:6(1cement :6sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:3:6 (1cement:3sand:16graded stone agregate 20mm nominal size ) and curring complete excluding cost of form work in foundation and plinth including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying spartic ceremic tiles 5.5mm thick in flooring 300x300mm size on treads of steps laid on a bed of 12mm thick cement mortar 1:3(1cement:3sand) finished with flush pointing in white cement including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Digital Wall tiles 10mm thick in skirting risers of steps and dado 12mm thick cement mortar 1:3(1cement: 3sand) and jointed with cement slurry. (Premium quality) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying heavy duty precast cement concrete inter locking paver blocks vibro compacted upto M- 50 grade i/c border or kurb block gray or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1cement:4sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curring rubbing & polishing complete (sub base concrete floor to be paid for separately) 60mm thick inter locking blocks.

P/L Granite Stone in flooring 20mm thick base in Cement Mortar 1:3 (1 Cement : 3 Sand) i/c jointing with grey cement slurry mixed with pigment to match the shade of pigment to match the shade of granite stone i/c rubbing and polishing complete 20mm thick including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing aluminium anodised powder coated pattern to existing window/ventilatior with 80mmx80mm panels holes with 25x8mm thick aluminium flat in windows and ventilators including fixing with aluminium screws or bolts and nuts complete in alluminium channels base frames (Aluminium channels base frames to be measured and paid for separately) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel work welded in built, up saction in trusses and framed work including cutting hosting fixed in position & applying a priming coat of red lead paint in including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. ( a)In trusses and trussed purlins. For Roof

b) In grating framed guard, bars ladders, railing, brackets and similar works.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia mter with prepainted limpet and rubber washers complete with all accessories including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing ridges or hips 60cm over all with 0.60mm thick prepainted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating back coat of polyster of 5 microns over 5 microns primer coat ing including fixing with prepainted iron j or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.

Providing & fixing M.S. BP sheet 1.66mm to 2mm thick in eaves board/ facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-Charge (Base members of steel work shall be measured & paid separately) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 15cm wide 45cm over all semicircular plain GI sheet gutter with iron brackets 40x3mm size bolts and nuts and washers making necessary connection with rain water pipe as per design including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. (a) 0.63mm thick sheet

Providing and fixing 19mm thick water proof commercial board in shelves/ box for cup board with butt joints & fixing with nails & screws etc complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 19mm thick water proof commercial board shutters for cup board i/c fixing with nickel plated piono hinges with screws complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 1.00mm thick coloured or plain lamination sheet(sunmica) on board/ply wood sheets with approved adhesives and nails etc complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing commercial Ply wood ceiling of approved quality 6mm thick. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing square edges cover fillet (beading) 19mmx6mm section i/c mitring at junction with wood screws and nails complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing bright finished brass handles with screws etc. Complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. (a) 100mm

Providing and fixing magnetic catchers for cupboard with screws etc. Complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Painting two coat (excluding priming coat) on new steel and other metal surface under coat with ready mixed paint brushing to give an even shade including cleaning of all dirt, dust and other foreign matter with ready mixed paint other than white including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Applying birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final metter finish to the surface complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly Surface free from mortar dropping brushing the and other foreign matter and sand papered smooth including applying of putty a required for metling the surface including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Finishing wall with exterior grade emulsion equivalent to Apex of Asian brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Cement concrete flooring 1:2:4 (1cement: 2sand: 4graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement 40mm thick including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Applying cement slurry on Cement concrete work using 2.75kg of cement per sq. Meter of floor/wall complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying brick aggregate 40mm thick in soak pit. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing steel curtain rods with clamps, finals and end caps complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face PVC (D-plast) rain water pipes for working pressure not less than 4.5kg/sqm i/c filling the joits with the approved adhisives complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. (a) 150mm

Providing and fixing PVC pipe spigot and socket soils waste and ventilating pipes lead caulked joints to be measured and paid for separately including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. . (a)110mm

P/f P.V.C. Fittings and accessories. (a) P/f PVC plain bend ISI marked including fixing with approved adhesives etc. Complete 150mm dia

b) P/f PVC plain bend ISI marked including fixing with approved adhesives etc. Complete 110mm dia including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

c) P/f PVC plain bend ISI marked including fixing with approved adhesives etc. Complete 75mm dia including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

a) P/f PVC Door bend ISI marked including fixing with approved adhesives etc. Complete 110mm dia including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

b) P/f PVC Door bend ISI marked including fixing with approved adhesives etc. Complete 75mm dia including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

a)P/f PVC Sinlge equal branch of required dergree ISI marked including fixing with approved adhesives etc. complete 110mm

b)P/f PVC Sinlge equal branch of required dergree ISI marked including fixing with approved adhesives etc. complete 75mm

Providing and fixing PVC clamps ISI marked of approved design with steel screws and raw plugs etc. complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. . (a)150mm

Providing and fixing to wall ceiling and floor Galvanized mild steel tubes (Medium Grade) tube fitting and clamps including making good the wall, ceiling and floor 20mm dia. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing to wall ceiling and floor Galvanized mild steel tubes (Medium Grade) tube fitting and clamps including making good the wall, ceiling and floor 15mm dia. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Making connection of galvanized mild steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and treading the pipe complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing & fixing pvc floor trap of self cleaning design with sand cast iron screwed down or hinged grating with or without vent arm complete i/c cost of cutting & making good the walls and floors. 110mm nominal dia. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

P/F vitreous china wash down water closet (European type, W.C. Pan) with integral 'P'or 'S'trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement:1 Sand) Ordinary Type complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT Coloured / white high density polythelene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float,with push button,couplings for connections with inlet, outlet and ovrflow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow) pipe to be measured and paid for separately including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

P/f plastic seat and cover for wash down water closet with CP brass hinges and rubber:- solid type white plastic seat cover including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing water jet for water closet complete with all fittings such as Connection pipe. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C. P. waste with CI or MS Brackets painted white including cutting holes and making good the same but excluding fitting. 610x460 mm with bowl depth 200mm.

Providing & fixing vitreous china wash basin with pair of hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fittings flat back 630 x450mm of reputed make. Oval Shape

Providing & fixng CP Brass waste for wash basin or sink 32mm dia. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing & fixng PVC waste pipe for wash basin or sink 32mm dia. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing & fixing 100mm sand cast iron grating for gully, floor or Nahni trap. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing & fixing 600 x 450mm bevelled edge mirror of superior glass mounted on 6mm thick AC sheets or plywood sheet and fixed to wooden plugs with CP brass screws and washers including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass towel rail complete with C.P. brass bracket fixed to wooden plugs with C.P. brass screws. 600mm x 20mm.

Providing & fixing CP brass Pillar tap with capastan head 15mm dia. (having weight not less than 400 grms) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing & fixing CP brass bib tap with capastan head 15mm dia.(having weight not less than 400 grms) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 15mm mixer for kitchen sink with top / bottom swinging spout including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

P/F C.P. brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

P/F C.P. brass angle valve 15mm without Nuts and pipe including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

P/F brass stop cocks: (a) 15mm dia

(b) 20mm dia

Providing & fixing PVC connection pipes with brass unions 45cm lenght 15mm nominal bore including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing G.I. or M.I. unions. 15mm dia including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PVC water storage tank G.I. Inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement i/c hoisting upto all heights above ground level: 1000 ltrs. net Capacity tank including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing & fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked i/c fixing with approved adhesive etc. Complete.i)160 mm dia including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Constructing manhole with RCC top slab in 1:2:4 (1cement: 2sand: 4graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 (1cement: 4sand: 8graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement: 3sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement: 2sand: 4graded stone aggregate 20mm nominal size) finished smooth complete including curing complete and testing. Inside size 800 x 800mm and 500mm deep including RCC cover and frame medium duty 500mm internal dia with 200mm thick walls of brick masonary using common burnt clay building bricks in cement mortar 1:3 (1cement: 3sand) complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Cutting in earth work and disposal of excavated earth upto all lead and all lifts in all kind of soils including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Sunil Kumar Sood