Spl repair to toilet block of bldg No P-4 OTM accn and P-12 and P-13 (Cook House) of OTM accn at Tibri Mil Stn under GE Gurdaspur.

Amount

Dismantling of roof brick tiles fixed in cement mortar in single layer

Demolition mud phuska in roofs any thickness including plastering and leeping all as spd

Roughing the surface of old concrete in floor/ roof, picking sweeping clean and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm.

M&L for cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate as in roof padding averaging thickness of 50 mm complete all as specified.

M&L for 10 mm thick cement plaster in CM (1:4) using WPC on RCC roof slab finished even and fair complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) laid on primed surface with bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface including finishing with two coats of aluminium base paint complete all as specified and all as per manufacturer's instructions.

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone agg) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for 75mm thick Cement concrete type D- 2, 1:4:8 (using 40mm graded stone aggregate) in sub base complete all as specified.

M&L 100mm thick cement cocnrete type D-2 , 1:4:8 (using 40mm stone aggregate) as in sub base complete all as specified.

Demolition of cement concrete in ground floor & paving n.exc 15cm above ground level complete all as specified and directed.

M&L for 75mm thick cement cocnrete type C-1 (1:3:6) (20mm graded stone aggregate) as in plinth protection finishing the surface even and fair including cutting grooves 10mm x 30mm deep at every 3.0m interval and filled with mastic filling comprising 1 part of mastic bitumen and 3 parts of sand (all by weight) complete all as specified and directed.

Dismantling floor hearth or wall tilling including cement mortar bedding removing rubbish off premises

M& L Non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm and not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement with pigment to match including 15 mm thick screed bed in cm 1:4 complete all as specified.

M&L for ceramic glazed dark shade coloured tiles of size 350x250x 7mm/ 450x350x7mm thick joint free on and including 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in coloured cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/dado complete.

S&F machine cut kota stone slab flooring 20-25mm thick in riser of steps, floors etc. over & including cement screed base 20 mm thick in CM 1:6 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) complete all as specified and directed by Engineer-in-Charge.

M&L for grinding of existing machine cut kota stone slab flooring including rubbing and polishing (with bees wax polish) complete .

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, counter platforms etc., laid, bedded and pointed in any mortar complete all as specified and as directed.

S&F Udaipur green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, laid over and including 15mm thick cement screed bed in CM 1:4

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as directed.

M&L rendering 15mm thick in CM 1:4 in sunken portion of slab using water proofing compound finished even and fair complete all as specified. Note : WPC shall be measured and paid separately.

Supply only integral water proofing compound

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) laid on primed surface with bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area/ sunken floor with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed.

M&L for PCC 1:5:10 type E-2 using 40 mm stone agg as in filling, foundation and mass concrete in sunken floor.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base Complete all as spd.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as directed.

M&L for form work to rough finished surface of concrete flat to soffits of shelves, chajja, fins etc including supports, over hangs

S&F 10mm dia and over TMT bar cut to length bent to shape required including cranking bending spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securing with clips as apd.

S&F mild steel TMT bars 6 to 8mm dia, cut to length bent to shape required, including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for RCC in 1:2:4 type B-0 (using 12.5 mm graded stone agg) as in chajjas facia, shelves etc and similar work all as spd.

M&L for precast reinforced cement concrete in landings, cover slabs (for manholes etc.) and similar articles with plain faces Type B1 1:2:4 (20 mm graded aggregate set in cement motar 1:4 complete

Taking down cement plaster of any description on brick, concrete or stone walls, ceiling etc including raking out joints, hacking for key scrubbing down with water and removal of rubbish off the premises where directed complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 on ceiling of roof and soffits of roof beam surface finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:4 on fair faces of brick or concrete surfaces, finished fair and even with WPC, height upto 12m complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for rendering 12mm thick in cement mortar 1:6 on other than fair faces of brick or stone surface, finished the surfaces even and smooth without using extra cement complete all as specified.

M&L preparation of new plaster surface and applying two coats of cement base paint complete all as specified and directed upto height 12m.

M&L preparation of new plaster surface of ceiling and applying three coats of white wash complete all as specified.

M&L for prepration of new plastered/un plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of cement based paint.

M& L for preparation of old treated surface of ceiling and applying one coat of white wash.

M & L for preparation of old decorated wall surfaces and applying one coat of white wash complete all as specified

M&L for preparation of new wooden surface of any decsription not other wise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer.

M&L for preparation of new steel surface of any decsription not other wise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer.

M&L prepartion of old painted surface of steel surfces of any decsription not other wise described over 10cm width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted wooden surface of any decsription not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new plaster surface and applying two coats of Oil bound distemper of wall over a coat of primer on wall complete all as specified and directed by EIC.

M&L for Preparation of old plastered surface of walls and applying one coats of oil bound distemper on wall complete all as specified and directed by EIC.

M&L for preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing surfaces and applying one coats of cement base paint on wall height upto 6m complete all as specified and directed by EIC.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter from from the chowkats)

All as per Srl item No 49 above but exc 1.50sqm but n.exc 4 Sqm

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed.

Taking down shutter of any description exc 2.00 Sqm each complete all as specified and directed.

S&F pressed steel frame for doors with one or more rebates including necessary lugs, hinges, lock strike, plate etc complete of size 105x60mm all as spd.

All as per Srl item No 53 above but size 125x 60 mm complete all as specified and directed.

M&L for cement concrete 1:3:6, type B0 using 12.5mm graded aggregate in filling of MS frames.

S&F 30mm thick factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to e fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S&F 35mm thick factory made flush shutters, soild core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

S&F 35mm thick second class hard wood (Hollock), glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a) supplied and fitted to chowkats complete all as specified and directed.

S&F aluminium anodized barrel tower bolt of extruded section 200mm long complete all as specified and directed.

S&F extruded aluminium alloy handles 150mm long, fabricated type, anodised

S&F extruded aluminium alloy handles 100mm long, fabricated type, anodised

S&F 75mm size medium weight mild steel butt hinge fixed with metal surface through bolts or welding or screws complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 75mm size hasp and staple safety type aluminium anodised hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frame, glazed with putty/ fixed with beads.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares n.exc. 0.50 Sqm each pane complete all as specified and directed.

S&F 4.8 mm thick sheet glass ordinary quality in square or rectangular in size n.exc 0.5sqm each pane in aluminium door or window shutter complete all as specified and directed

S&F 4.8 mm thick black sheet glass ordinary quality in square or rectangular in size exc 0.5sqm each pane in aluminium door or window shutter complete all as specified and directed

S&F 3mm thick figured glass pin head type glazing with oil putty, in square n exe 0.5sqm in each pane.

S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including taking down old existing window complete:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass, painting shall be measured and paid for separately

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including taking down old existing window/ ventilator complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, painting shall be measured and paid for separately

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples/ beads complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples/ beads complete all as specified and directed.

Taking up or down GI pipe15mm bore and connections including cleaning and refixing in any position with all fittings complete all as specified and directed.

All as per Srl item No 74 above but 20mm bore of pipe

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or laid in floor etc with all fittings ISI marked including taking down existing pipe and connections complete all as specified and directed.

S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or laid in floor etc with all fittings ISI marked including taking down existing pipe and connections complete all as specified and directed.

S&F rotational moulded polytheylene triple layered water storage tank white of 1000 ltr capacity (cylinderical vertical with closed top) hoisted and fixed in position including dismentling of old UNSV WT complete all as specified and directed.

S&F rotational moulded polytheylene triple layered white water storage tanks of capacity 500 Litres(cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank complete all as specified.

S&F in repair 20mm ball brass valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixedas spd

S&F in repair bib tap 15mm bore dia, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repair for 15mm bore stop valves/ angle valves, but fancy type, chromium plated cast copper alloy, screwed down, high pressure, handle, screwed both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair brass chromium plated shower rose fancy type 125mm size with swivel joints, including fixing to steel pipe or union with brass CP arm 195mm long, 15 mm size complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia. `D’ type 60cm long between flanges fixed to wall all as spd and directed by Engr-in-Charge

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or floor all as specified & directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls or floor complete all as specified.

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches, if required

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with integral foot rest including connection to trap and flushing pipe and bedding in PCC 1:7:12 type F-2 complete all as specified

S&F in repair for Vitreous China wash down water closet pan (pedestal pattern) white (excluding flushing cistern and flush pipe) including plastic water closet seat white closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device with CP brass jet,complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified complete all as specified as directed

S&F in repair vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe), waste coupling and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing around urinal back in cement, grating and union for discharge pipe all as spd

S&F in repair PVC(SWR) branch piece single (single Y) equal or unequal 110mm bore with oval access door

S&F in repair 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC. 32 mm dia complete all as specified and directed

S&F in reapir vitreous china counter top oval wash basin, white, size 500mmx400mm complete all as specified and directed.

S&F in repair vitreous China wash basin, white flat back, size 630mmx 450mm including brackets complete all as specified and directed.

S&F in repair pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F in repair vitreous china urinal partition white of size 310mmx 700mm, terminating about 40cm above floor line

S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair PVC (SWR ) bends 110 mm bore any radius

S&F in repair PVC (SWR ) double junction (double-T Cross) 110 mm bore equal or unequal with oval access door

All as per Srl item No 103 above but 75 mm bore

S&F in repair PVC (SWR ) vent cowl 110 mm bore

S&F in repair PVC (SWR ) vent cowl 75 mm bore

M&L in repair PVC (SWR ) floor trap 75 mm plain with MS grating including jointing with solvent cement complete all as specified and directed.

M&L in repair 110mm bore PVC (SWR) 'P' or 'S' trap including jointing with solvent cement

S & F Stack clamps (100mm pipe) out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof

S & F Stack clamps (75mm pipe) out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars & precast concrete masonry etc complete all as specified & directed by Engr-in-Charge.

M&L brick work with old size sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Material and Labour for repairing to RCC projections, chajjas, roofs, facia, ceiling etc. by scrapping, cutting, chiseling, de-rusting and cleaning exposed reinforcement of damaged loose RCC surfaces and applying neat cement slurry @ 3kg/sqm and filling the surfaces with cement sand mortar 1:3 or cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) using coarse sand in layers as required and reinforced with 8mm dia. TMT bars in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of finishes to match with the existing surfaces at height upto 12m complete all as specified. Note:- Cost of formwork shall be deemed to be included in unit rate quoted by the Contractor.

S&F anodised aluminium powder coated door shutters, aluminium section weighing average not less than 1.00kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S&F anodised aluminium powder coated frame for doors, windows, ventilators, with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F anodised aluminium powder coated window/ ventilator shutters side hung type without sash bars, aluminium section weighing average not less than 0.75 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

S&F Mortice lock, aluminium vertical type size 100mm 4 levers complete all as specidfed and directed.

S&F in repair aluminium (die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

M&L for block boards, 25mm thick, grade 1 quality, exterior grade, , decorative type with decorative face veneer on both faces, fixed with screws to timber frame work for shelves, partitions and shutters including dismantling of old board.

S&F mild steel work conforming to Fe-290 Gde E-165 in framed work as in door frame, chowkat, shutter or gates of angle iron or other section with gusset plates,rails,braces etc complete drilled for fixing of steel sheeting or orther covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening complete all as specified and directed

S&F 300mm, mild steel ordinary rat tail rod pattern springs,including roller and roller plate joint through welding/bolt in metal/wooden frame to be carried out or necessary alternative arrangements to be done complete all as specified and directed.

Supply and fixing cutrain rod 20mm dia of Mild steel PVC Coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

S&F floor door stopper overall length of cover plate 140mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repair PVC waste pipe 32mm dia 800mm to 1200 mm long fixed to wash fitting of wash basin and sink all as specified and directed.

S&F in repair brass CP waste coupling (half or full threaded) bore dia of discharge pipe 32mm for WHB complete

S&F in repair stainless steel oval shape soap dish holder, fixed to plugs with chromium plated brass screws complete all as spd and directed.

M&L 60mm thick PCC (M-35) factory made coloured interlocking tiles/ paver block of shape/ size as conforming to IS 15658, joints will be filled with fine sand complete all as specified and directed by Engineer-in-Charge. Note :- Sand will be paid under relavent item.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick plaster in cement mortar 1:4 on brick or concrete surfaces of roof finished surface even and fair with WPC including roughing the surface of old concrete floor picking sweeping clean and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately.

E/M PORTION Taking down carefully aluminium/copper point wiring for light, fan, bell, socket of point complete fittings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc.

Point wiring with PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm including concealed PVC conduit with fittings and making good to the disturbed surfaces with continuous earth wire of PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing to existing CI/MS boxes for mounting of accessories like surfaces sockets and regulators etc. complete all as specified for One light point/fan point/ bell point controlled by one one way switch

All as per Srl item No 131 above but one 5 amp socket out let on same board.

All as per Srl item No 131 above but One 5 amp socket out let on independent board.

All as per Srl item No 131 above wiring with 2.5 sqmm FRLS copper wire including earth wire 2.5 sqmm of copper for 15 Amps 3 pin socket outlet.

M&L for sub main wiring with two single core multi stranded PVC insulated, unsheathed copper conductor of grade 1100 Volt , FRLS cable of size 6 sqmm (red for phase and black for neutral) and including electrical grade PVC conduits of desired colour not less than 1.2 mm thick and 32 mm wide & 6 sqmm multistranded copper conductor FRLS cable PVC insulated unsheathed green coloured for earthing with complete accessories duly connected with earth duly complete and taking down old unserviceable one. Note :- (a) Cost of making good the disturbed surface plastering/ filling putty alongwith finishes matching with the existing is deemed to be included in the quoted rate by contractor. (b) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 5 amps.

S&F socket outlet 3 pin 5 amps flush type

S&F switch piano flush type 15 amps single pole type one way

S&F socket outlet 3 pin 15 amps flush type

S&F in replacement surface mounting universal batten housing made of powder coated CRCA sheet suitabe for and upto 1 x 18/20W LED tube rod and taking down existing old unserviceable fitting complete all as specified and directed.

S&F LED tube light 20W ultra bright LED polycarbonate tube light with very high efficacy suitable for fitting into tube light batten fitting complete all as as specified and directed. Note :- The contractor will submit the LM-80 and LM-79 report from manufacturer to Engineer-in-Charge before incorporating the items in work.

S&F lamp holder PVC body angle type including 9 watt LED bulb polycarbonate body complete all as specified and directed.

M&L ceiling rose, 3 terminals/ phase/ PVC/ polycarbonate, isolated body, surface

S&F in repair sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 8 way with bus bar SPN double door complete all as specified and directed. Note :- All the connection of incoming and outgoing wire in MCB will be made with thimble with suitable size as directed.

S&F in repair MCB single pole 6 amps to 32 amps complete all as specified and directed.

S&F in repair MCB single pole and neutral 40 Amps complete all as specified and directed.

S&F exhaust fan, metal body Ac single Phase 230V of size 300mm sweep with blades and frame and louvers and making hole of suitable size complete all as specified and directed.

S&F in repair of fan regulator electronic type 5 step type 100 watt, 240 Volt and connecting complete all as specified and directed.

Note: A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

MALKIT SINGH AND SONS

Harbhajan electric co

talwinder singh and co

M/s kulwant singh and sons

D.RAJ And CO.

JOGRAJ CONSTRUCTION COMPANY

KAILASH CONSTRUCTION CO

M/s SODHI SALES CORPORATION

M/s. Nirmal Singh

M/S GAGAN CONSTRUCTION CO