Repair to paved area, protective work, security wall, gate, fencing, drain and hard standing at JAKLI RC under GE 970 EWS

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceding 15cm thickness (below or above ground level), complete all as specified and as directed.

M&L for 100mm thick PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggte) as in floors finished even and smooth without using extra cement, complete all as specified and directed .

M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

M & L Johnson Endura paving tiles of techno commercial eqivalent of size 300x300x10 mm thick set and jointed in neat cement slurry and pointed with white cement to match the joint, over and incl 15mm thick screed bed or bedding layer of mortar 1:4 in cement mortar complete all as specified and directed.

Demolition of brick work built in cement mortar incl all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work and precast concrete articles, complete all as specified and directed .

M&L for Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in CM 1:6, complete all as specified and directed .

Description all as per ser item No 08 above but except bricks, complete all as specified and directed .

M & L brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in CM (1:4), complete all as specified and directed .

M&L for walling of random rubble, uncoursed, well bounded, bedded and solidly heated, built in cement mortar 1:4 for random or polygonal rubble walling, brought up to course complete all as specified and directed.

Description all as per ser item No 11 above but except stone.

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed..

M & L Rendering (10+5) mm thick on fair faces of brick work or concrete surfaces ion cement mortar 1:4, finishing the surface even and smooth ( without using extra cement) in two layers complete all as specified and directed .

M & L Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement morar 1:6, finishing the surface even and smooth ( without using extra cement complete all as specified and as directed.

M&L flush pointing 1:4 to random or polygonal rubble stone masonry, uncoursed or brought upto courses complete all as specified and directed .

M&L for raised pointing to randomor polygonal rubble, uncoursed or brought upto courses in cm 1:4 complete all as specified and directed .

M&L for PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) in surface channels and drains, complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc, complete all as specified and directed.

M&L for PCC 1:2:4, type B-1(using 20 mm graded crushed stone ggregates) as in coping incl necessary form work, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6, type C-2, using 20 mm graded aggregates as in plinth protection etc, finished even and smooth without using extra cement complete all as specified including joints filling with sealing compound Grade "A", complete all as specified and directed.

Hard Core of guage not exceeding 63mm deposited, spread levelled in layers not exceeding 15 cm thick using brocken stone or boulders of trap stone, watered and rammed to a true surface complete all as specified and directed .

M&L 100 mm thick cement concrete in alternate bays 1:2:4, type B-1, (using 20 mm graded stone aggragate) in sub base and finishing cement concrete surface fair and even without using extra cement, complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed .

S&F for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete FE 410-W (Gde- E-250) quality A, complete all as specified and directed.

M&L for framed work such as grills,gratings, etc. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed .

M&L for 1 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

S&F mild steel bolts dia metre of neck exc 12mm n. exc 20 mm purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut exc 30cm long complete all as specified and directed.

Dismantling fancing of barbed wire any type complete all as specified and directed.

Supply of Chain link MS galvanised fencing, any size or type complete all as specified and directed .

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed .

S & F in repairs Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and strainning and fixing to any type of strandred rails strainning bolts, incl securing or tying at crossings with and provn of galvanised mild steel wire, staples or steel pins etc, as directed (each line wire to be measured) complete all as specified and directed .

Restrainning resecuring incl making good with staples Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed .

S&F concertina coil punch type 600/900/1050 mm fixed dia on top of walls/angles/on ground etc or laid and fixed in any position incl necessary acessories & arrangement to fix the coil complete all as specified and directed .

Preparation of newly plastered surfaces of wall with a coat of 2 mm thick wall care putty and applying two coats of Apex paint (Exterior Emulsion) over over a coat of suitable primer, complete all as specified complete all as specified and directed . Note: The contractor shall submit Manufacturer/ company performance warranty for minimum five years.

Preparation of new steel surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for Preparation of old steel painted surfaces and applying one coats of synthetic enamel paint complete all as specified and directed .

M&L for Preparation of newly platered /conrete surfaces and applying two coats of synthetic enamel paint complete all as specified and directed .

Notes :- An amount of ` 46,000.00 on account of Credit Schedule for Schedule 'A' Part-ll shall be deducted from total quoted amount of BOQ to arrive at the contract sum

M/S Sultan Enterprises (BID ID -3196054)

M/S LATIF AHMAD BABA CONSTRUCTION (BID ID -3190299)

M/S A.R TANTRAY (BID ID -3190699)

M/S HAJI ZAHOOR HUSSAIN GANIE (BID ID -3190374)

M/S BASHIR AND SONS (BID ID -3186807)

G N Constructions (BID ID -3196534)

M/S B A Traders (BID ID -3190562)

M/S SK ATLANTIC ENTERPRISES (BID ID -3189882)

M/S MEGA BUILDERS (BID ID -3190409)

M/S Thakur & Sons (BID ID -3196495)