SPL REPAIR OF GOVT MD ACCN NO P-100/1 TO 100/8, EXISTING SEWAGE LINE AND PROVN OF CAR PARKING SHED WITH HARD STANDING AND FOL SHED UNDER GE BABINA

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed by the Engr-in-Charge. NOTE :- (i) Any existing structure like Road/Hardstanding/Interlocking/PCC/Plinth protection /any type pathway etc are damaged/effected during the constrction/ laying of sewage pipe line. It has been repaired/constructed as per existing standard with required material/items by the Contractor. Unit rate for the same shall be included in this item

Description same as per item No 1 above, but exceeding 1.50M and not exceeding 3.00M in depth and getting out in any type of soil soil/any existing road crossing /PCC /Interlocking complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC ,PVC or Reinforced concrete) set in cement mortar including packing under and haunching against side of pipe for 200mm internal dia complete all as specified and directed.

M&L for concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement mortar 1:4:8 type D2 using 40mm graded stone aggregate for 200 mm internal dia of pipe complete all as specified and directed by the Engr-in-Charge.

Supply & laying, jointing and testing for 200mm internal dia of reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and as directed by the Engineer-in-Charge. NOTE :- (i) Contractor has to construct the temporary septic tank and sockage well building wise arrangment for sewage disposal during execution of work. (ii) Contractor should clean all sewage line, septic tank, manholes and sockage well by using honey chakar machine. (iiI) Contractor should clean lines of sewage lines on daily basis during the execution if directed by the Engr-in-Charge. (iv) Contractor must have responsible to maintain hygiene and sanitation of sewage during the execution of work. (v) Unit rate for the same (Note (i) to (iv) shall be included in this item. No extra payment has been given to the contractor.

Demolition of brick work or stone masonary built in cement mortar as in drain, mahholes, septic tank and sock well complete all as specified and directed.

M&L brick work with sub class 'B'brick straight or curved on plan exc 6m mean radius built cement mortar 1:4 complete all as specified and as directed

M&L brick work with sub class 'B'brick straight or curved on plan exc 6m mean radius built cement mortar 1:4 but except bricks (Brick shall be obtained from demoltion and cleaning of old bricks etc) complete all as specified and as directed

M&L for cement concrete type C2 (1:3:6) (using 40mm graded stone aggregate) in suface channels, drains and manholes foundation etc 1:4 complete all as specified and as directed

M&L for rendering 15mm thick on fair faces of wall even and smooth finish without using extra cement on conc/brick surfaces in CM 1:6, complete all as specified and as directed

M&L for two coat of white wash on newly plastered surface on wall and curing preparation of surface all as specified and directed by the Engr-in-Charge.

Demolation of reinforced concrete of any description and in any position complete all as specified and directed by the Engr-in-Charge.

M&L for precast cement concrete 1:2:4 type B1 (using 20mm graded stone agg) in landings, cover slabs for man holes etc set in cement mortar 1:6 chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including necessary formwork complete all as specified and directed by the Engr-in-Charge.

S&F TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by the Engr-in-Charge.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in excavated approved earth into trenches around pipe etc complete all as specified and directed by the Engr-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by the Engr-in-Charge.

Taking down existing AC/PVC rain water/ sewage line/waste pipe from wall or floor complete all as specified and directed by the Engr-in-Charge.

S &F of 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors or fixed wall and complete all as specified and directed.

S &F of 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors or wall and complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore.

S&F PVC (SWR) bends any radius 75mm bore.

S&F PVC (SWR) junction single, (single T) equal or unequal 75mm bore with access door.

S&F PVC (SWR) junction single, (single T) equal or unequal 110mm bore with access door.

S&F PVC (SWR) vent cowl 110mm bore.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone agg) as in foundation filling and mass concrete, sub base and complete all as specified and directed by the Engr-in-Charge.

M&L for 75mm thick cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for 50mm thick cement concrete type B2 1:2:4 (40mm graded aggregate) as in floor/hardstanding finished even ans smooth without using extra cement complete all as specified and directed by the Engr-in-Charge.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or sewage line, drains under the roadc/path/hardstanding crossing (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed. within a lead of 50 m. complete all as specified and directed by the Engr-in-Charge.

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in hard/dence soil complete all as specified and directed by the Engr-in-Charge.

Excn in post holes each n exc 0.50Cum and getting out in hard/dense soil for foundation of vertical post complete all as specified and directed by the Engr-in-Charge.

M&L for broken stone hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15 cms thick, watered and rammed to true surface etc complete all as specified and directed by the Engr-in-Charge.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in foundation/bed embedding pipes etc complete all as specified and directed by Engr-in-Charge.

M&L machine pressed rubber moulded coloured precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 80mm thickness, M-40 grade with grey cement & pigment complete all as specified and directed.

S&F steel work ( tubular pipes,square/round as in vertical posts, rafters/purlins framed using ERW or induction butt welded including tubular pipes (medium) for supporting tubular/square pipe rafters/purlins special shaped washer incuding welding and cutting in shape etc complete all as specified and directed by Engr-in-Charge.

S & F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, any attachment , welding with riveted, bolted or welded attachment completed all as specified and directed by Engr-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by Engr-in-Charge

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by Engr-in-Charge

PM&L brickwork with fly ash brick, straight or curved on plan exc 6M mean radius, built in cement mortar (1:6), rise of hight for brick wall complete all as specified and directed by Engr-in-Charge

M&L for rendering 15mm thick on fair faces of wall even and smooth finish without using extra cement on conc/brick surfaces in CM 1:4, complete all as specified and as directed

M&L preparation of steel surfaces over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

S & F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, any attachment , welding completed all as specified and directed by Engr-in-Charge.

Excavating over areas, n exc 1.5m deep and getting out in any type of soil complete all as specified and directed by the Engr-in-Charge.

M&L, 200 mm thick soling or sub base with broken boulders or quarried stone, inter stices filled, surface formed and rollled and consolidated to required camber and gradient complete all as specified and directed

M&L 150 mm thick (compacted thickness) WBM in two layers, each 75 mm thick with stone coarse aggregate of grading 2 (63 to 40mm ) spread, rolled and consolidated to gradient material and camber required complete all as specified and as directed

M&L cement concrete work in pavement/hard standing of flexual strength 40Kg/per Square centimeter in field using 400kg of cement per cubic meter, thickness of concrete 25cm or less including form work complete all as specifed and directed by Engr-in-Charge.

M&L for forming 12mm thick expansion joints in 200mm thickness slab filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ etc complete all as specifed and as directed by Engr-in-Charge.

M& L for demolition cement concrete of any description in any position not otherwise specifically provided including existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down cement concrete, existing plaster lime coba 80 to 100mm thick mud phuska/cement concrete/lime coba etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush and removing debries/rubbish off materials out side of Ministry of defence (MOD) land complete all as specified and directed.

M&L for 10 mm thick rendering in cement mortar 1:4 on concrete surfaces when concrete is stil green finished even and fair including mixing of water proofing compound and black polyethylen film 175 micron laid in floor as per manufacturer instruction etc complete all as specified and as directed.Note :- Water proofing compound shall be measured separately

Supply only integral water proofing compound complete all as specified and as directed.

M&L applying water proofing treatment with the following

(a) First coat of bitumen primer conforming to IS-3384 @ 0.3Kg / sqm to be applied on prepared surface till the surface is properly impregnated.

(b) after the application of approved bituminous primer the water proofing memberne minimum weight 3kg/sqm and minimum 3mm thick reinforced with polyesterd non woven fabric (weight not less then 160gms/sqm) shall be laid on the primed surface by torch application method as per manufactured instruction.

(c) All joints and change in direction should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag on cement and cured well before laying of membrane including Aluminium paint on top surface

M & L for cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed; set, jointed and pointed in net cement slurry in floors etc, and cut and polished, rubber moulded with grey cement with pigment over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

Taking down plaster on brick or stone wall, ceiling etc incl racking out joints hacking for keys scrubbing down with water etc complete all as specified and directed.

M & L 10 mm thick rendering on other than fair faces of brick work or concrete surface in cm 1:6 to be finished fair and even with out suing extra cement.

M&L for external rendering 15 mm thick in CM 1:4 mixed with WPC @0.20Ltr/ bag by weight of cement on brick work or concrete surfaces of wall finished even and fair complete all as specified . Note-WPC shall be measured and paid seperately.

M & L for complete removal of existing treatment from surface of wall all as specified and as directed by the Engineer-in-Charge

M & L for applying 1mm water proof wall care putty on wall all as specified and as directed by the Engineer-in-Charge

M& L for two coat of exterior emulsion acyrlic weather proof antifungal paint over a coat of exterior grade primer on new plastered surface including preparation of surface complete all as specified and as directed

M & L for applying two coat of oil bound distemper on new plastered surface including preparation of surface complete all as specified and as directed

M&L for complete removal of existing treatment on wall surface and two coat of exterior emulsion acyrlic weather proof antifungal paint over a coat of exterior grade primer on old plastered surface including preparation of surface complete all as specified and as directed

M & L for applying two coat of oil bound distemper all as specified and as directed by the Engineer-in-Charge

M & L for preparation of old ceiling surfaces and applying two coats of white wash complete all as specified and directed.

S&F in repair Vitreous china squatting pan, 'orissa' pattern, size 580 x 440 mm white, with integral footrest (excluding flushing cistern and flush pipe) including provision of concrete beddig and joint to flush pipe to squatt pattern closet including all joints and making good to the floor and taking down old one complete all as specified and as directed.

S&F in repair 10 Ltrs capacity PVC flushing cistern valveles syphonic action type low level, white, with inlet ball valve, float & handle incl brackets & flush pipe complete all as specified and directed.

S&F in repair stainless steel sink with drainage board made of 1.00 mm thick steel sheet for kitchen or laboratory with plug, waste pipe, coupling, washers also incl cantilever cast iron brackets connecting union etc, overall size 915x460mm with bowl size 410x330x160mm complete.

S&F PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and as directed .

S&F in repair 15 mm stop valves angular type, cast copper alloy, screwed down, high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed .

S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60cm long between flangs complete all as specified and as directed.

S&F in repairs 15mm bore fancy type chromium plated bib taps long body with crutch of butterfly handle screwed down for iron pipes complete all as specified and as directed.

Supply and fix in repairs of size 125 mm brass chromium plated shower rose with or without swivel joints, any size including fixing to steel pipe or union complete all as specified and as directed

S&F in repairs 15mm dia Concealed stop Cock regular body 15mm with flange complete all as specified and as directed.

S&F CP Brass soap dish fixed to wall with cp brass screws etc complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair stainless steel kitchen plate rack overall size 900mm x 900mm make out of 1mm thick stainless steel sheet etc complete.

S&F in repair chromium plate curtain rod with CP brackets and knobs at both end as per sample approved by Engineer-in-charge.

Taking down PVC soil pipe with fittings from wall, treches of any description including fittings complete all as specified and as directed.

S&F in repair PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls , 110 mm inetrnal bore , etc complete including taking out old unserviceable pipe all as specified and direcetd .

S&F in repair PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls , 75 mm inetrnal bore , etc complete including taking out old unserviceable pipe all as specified and direcetd .

S&F in repair PVC floor trap/Nahani trap outlet dia 75mm with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed

Dismantling water tanks and removing to store of capacity exc 500 & n.exc 1000ltrs etc complete all as specified and directed.

S&F rotational moulded polythylene water storage tank (three layered) (Cylendrical ,vertical with closed top) hoisted and fixed in position capacity 1000 Ltrs all as specified in SSR Part-I complete all as specified and as directed.

S&F ball valves of 20 mm bore high pressure of PTMT with empxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed complete all as specified and as directed(Minimum weight 20 gms-210 gms) complete all as specified and as directed

S & F in repairs 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs including taking down the existing fitting complete all as specified and as directed.

Taking up or down existing steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed for the following sizes:-

(a) 15 mm dia bore

(b) 20 mm dia bore

Supplying, fixing, jointing and testing galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed for the following sizes:-

(a) 15 mm dia bore

(b) 20 mm dia bore

Fixing only old steel tubing and connections obtained from taking down against item No 8(a) & (b) herein before in new or old position fixed to wall, ceiling or laid in floor with new fittings for the following sizes:-

(a) 15mm dia bore

(b) 20mm dia bore

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cuttingexceeding 10 cm but not exceeding 20 cm girth in brick walls

Material & Labour for writing letters or figures (block, Roman, Italic or Indian) n.exc.30 cm high complete all as specified and directed.

S&F Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips.

M&L for Formwork (rough finished surfaces of concrete flat) to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding, (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L 25mm thk PCC 1:2:4 type B-0 using 12.5 mm graded agg as in flooring finished fair and even without using extra cement complete all as specified and as directed.

M&L, screed bed or bedding layer of mortar 15 mm thick in cement mortar 1: 6 to receive tiles etc finished rough complete all as specified and directed.

M&L Ceramic tiles light or dark shed 8-10 mm thick, (square/ rectangular), area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm,polished, in floors etc.jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Ceramic tiles light or dark shed 8-10 mm thick, (square/ rectangular), area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm,as in skirting fixed over and including 10 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L for non skid white ceramic tiles 6 to 8 mm thick (square / rectengular) area of each tile exceeding 0.18sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and as directed.

Material & Labour glazed ceramic coloured tiles 1200x600x7-8 mm thick on skiriting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over 10mm thick bedding layer of mortar to wall in cm (1:4) for laying tiles on skirting/dadocomplete all as specified and as directed.

M&L for 18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed.

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sandt complete all as specified and directed.

M&L, for PCC 1:2:4 type B-0 using 12.5mm graded stone agg as in coping on side of path including necessary form work etc complete all as specified and directed.

Taking down chowkhats or frames with shutters ( without taking off shutters from froms exe 1.5 sqm and n.exe 4 sqm each

Taking down chowkhats or frames with shutters ( without taking off shutters from froms n exe 1.5sqm each

Taking down Shutters of any description n exc 1 sq. m each

Cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in CM 1:3 or cement conc 1:2:4 type B1 as required exc half brick but not exc full brick wall complete all as specified and as directed.

M&L PCC 1:3:6 type C-1 (using 20mm graded stone aggt) as in filling in holes of hold fasts and back filling of chowkats complete all as specified and directed.

M&L Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required:hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

S&F 18/19 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice laminations and other side balancing white lamination fixed with screws to timber frame work etc complete all as specified and directed

S&F for 12mm commercial plywood,grade BWR,typeBB,fixed with screws to timber frame work etc complete all as specified and directed

S&F 19 mm Cover fillet of external teak wood lipping 6mm thick fixed with nail all as specified and directed.

S&F Hasp & staple safety type aluminium anodized with mild steel hing pin incl bolt to hing plate and fixed with screws 100mm size etc complete all as specified and directed.

S & F 40 mm dia.,cup board knobs fixed with nut, screw and washer of brass, polished complete all as specified and as directed.

S&F, Pressed steel frames for doors(125x60) mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed etc complete.

S&F, Pressed steel frames for doors(105x60) mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed etc complete.

S&F plain framed paneled shutter 30 mm thick IInd class HW (any number & Panels) with lock rail and panel of 9 mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both face, the size of rail and style as per IS : 1003 (Part I) kiln seasoned and chemically pressure treated etc complete all as specified and as directed

S&F fabricated 30 mm thick IInd class HW glazed & skeleton shutters open rebated and prepared to receive glass gauge etc. (without sash bars) edges of framing plain chamfered or rounded fitted with cut & mitered beads for security glass/gauge etc. size of members of shutter as specified in SSR Pt I sec 8 Cl 8.20 (a), divided into squares with plain chamfered rounded, mitered and rebated sash bars etc complete all as specified and as directed

S&F, butt hinges medium weight cold rolled, mild steel and fixed 100 mm size etc complete all as specified and as directed.

S&F, aluminum handles cast type anodized 125 mm size etc complete all as specified and as directed

S&F, aluminum anodized barrel tower bolts of extruded section 150 mm long etc complete all as specified and as directed

S&F, aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) 300mm long etc complete all as specified and as directed

M&L, prepairing surfaces of wood and wood based material, steel and iron work, new or old, of any desctiption and girth not otherwise desctibed and treated with tar or coal tar black paint etc complete all as specified and as directed

M&L, framed work as grills, gratings, etc with ends of bars shouldered and/ or riveted into spikes; or forged into spikes, framed guard bars; barred iron doors and similar work confirming to Fe 290. Gd-E-165 etc complete all as specified and as directed

S&F galvanized mild steel wire cloth 0.63 mm nominal dia of wire and avg width of apertare 1.40 mm fixed with tinned tacks or galvanized wire staples etc complete all as specified and as directed.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

Supply, and fixing 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by insering horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineer in-charge

S&F Butt hinges, extruded aluminum alloy with galvanized MS sheet hinges pin anodized of100mm size type B-21..

S&F in repair aluminum adjustable automatic spring door closer (silver colour) with allen key and screws weight minium 200 gm etc complete and as directed.

M&L Brick work with sub class B bricks straight or curved on plan exe 6 m mean radius built in cement mortar 1:4 complete all as specified and as directed

M&L for PCC (1:5:10) type E2 using 40 mm graded stone aggregate as in filling and mass concrete complete all as directed and as specified.

M&L for rendering 15 mm thick in cement mortar 1:3 Mixed with Water proffing compound and black polyethylen film 175 micron laid in shunken portion and as per manufacturer instructions surfaces finished even and smooth without using extra cement complete all as specified Note - WPC will be measured separately.

M&L for applying two coats of OMNIPLAS EP -101 epoxy compound manufactured by M/S OM AGRO INDUSTRIES PLASTIC Pvt Ltd Bomboy or equivalent as approved by GE in proportions as per manufacturer instruction on complete surfaces of floor or wall of sunken portioncomplete all as specified and as directed

Supply only Liquid water proofing compound complete all as specified and as directed of as per manufacturer instruction.

Taking down carefully copper/ aluminium point wiring (light, fan, socket, or power) complete fitting such as switches, ceiling roses pendants, regulators, sockets, light fitting ceiling fan etc to be measured seperately ) removing materials for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperatly) and making good disturbed surface of walls floors etc all as specified and directed. Note-Responsibility after taking down fan/exhaust fan keep in safe custody of contractor and refix the same after before completion of work the rate of same deemed to be included in the item quoated rate.

Taking down carefully existing wooden board , Main switch, MCB DB boxes with MCBs, sheet metal boxes, cut out, etc of any size any capacity from boards complete all as specified and as directed.

Taking down carefully sub main wiring / service connection twin core from wall / LT pole of any size of Aluminum with wooden batten and or through rigid conduit including GI wire and making good the disturbed surfaces of walls, roofs, floors etc complete all as specified and as directed.

M & L for concealed point wiring complete with PVC insulated and unsheathed flame retardant low smoke and halogen ( FRLSH ) cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit not less than 20 mm dia, clip, with MS terminal boxes (not less than 1.6 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including common earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm green multi stranded copper conductor as continuous earth wire with lugs complete including cutting necessary chases on wall / ceiling surfaces for drawing of conduit & cables as required and making good disturbed surfaces of walls with CM 1:3:6 and matching with the existing surfaces including colour washing all as specified and as directed for the following :-

(a) One light point controlled by one switch

(b) One fan/exhaust point controlled by one switch & regulator.

(c) One 3/5 pin 5 Amp socket outlet point controlled by one switch on independent board.

(d) One 3/5 pin 5 Amp socket outlet point controlled by one switch on same board.

(e) S&F modular socket 20 amp with MCB 20 Amp 'C' type all specified and complete. (For geyser)

Description all as per item No 4 above but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed flame retardant low smoke ( FRLS ) cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with 2.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete all as specified and as directed.

S&F switch piano flush button type 5 Amp single pole one way complete all as specified and as directed.

S&F socket outlet 2in1, 3 pin, 5 Amp flush type complete all as specified and as directed.

S&F switch piano flush button type 15 Amp single pole one way complete all as specified and as directed.

S&F socket outlet 2in1, 3 pin, 5 Amp and 15 Amp flush type complete all as specified and as directed.

S & F delux Fan Regulator electronic rotary, step type 240 Volt 50 Hz, complete all as specified as directed.

S & F Lamp holder,PVC/Urea type with back plate suitable for batten fittings complete all as specified as directed

S & F 9W/10W LED retrofit lamp B-22 holder base with polycorbonate body and aluminium heat sink complete all as specified as directed.

S&F ceiling rose,surface POLYCARBONATE 63 x50mm three terminals complete all as specified and as directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 6 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. (NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

S&F TPN DB-DPX 125 MCCB DBs 4 way single door with provision for DPX 125 MCCB and as incomer and SP/TP MCBs as out going no of modules DPX 125+12, concealed Complete all as specified and as directed. Make:- ABB / Havells / HPL / Standard.

Supply and fix MCCB having breaking capacity of of 16 KA 415V, 4 pole having rating capacity of 100 Amp 100% ICU complete all as specified and as directed.

S&F sheet metal enclosure double door concealed suitable for distribution boards when MCBs to be used having 100 Amp rated bus bar SPN DB 8 ways 240 V complete all as specified and as directed .

S&F MCB single pole and neutral 40 Amp/63 Amp 240 V ,10KA , 'C' series, complete all as specified and as directed with copper lugs

S&F MCB single pole 6 to 32Amps 240 V,10KA, 'C' series,complete all as specified and as directed

Supply and fixing in repair 22 W LED 6000k Decorative ultra slim linear LED fitting fixture with extruded polycarbonate ,environmental friendly ,energy efficentinterated driver and 28watts lamp fitted including wiring upto and terminal into ceiling rose complete all as specified and directed by Engr-in- Charge.

Supply and fix LED 35/36 W building security light fitting,5700 K energy saving & environmental friendly long life versatile pressure die cast aluminium IP 66.road way luminare with high power LEDs as light source and electronic driver suitable for pole dia 35 mm including 35 mm dia light grade tube bracket ,bend to shape 1.80 mtr length with two nos of clamps of size 50mm x 6mm with nuts and bolts,washers etcincluding connection with 1.5sqmm threesingle core PVC insulated and PVC sheathed cable stranded copper cable upto ceiling rose and fixing on walls/pole complete all as specified and directed.

Supply and laying or fixing or passing through HDPE pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel or strip and overall PVC sheathed, 25 sq mm 4 core ISI Marked as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc complete all as specified and directed.

Supply and Fixing Exhaust fans AC single phase 230/240V of size 300 mm sweep, 1250-1350 RPM with louvre complete including with all arrangement of making holes on wall, making good and finishing of disturbed surfaces matching with the existing surfaces, necessary fixing arrangement such as fastener bolts, nuts, washers etc, of appropriate size all as specified and as directed

S&F BLDC Ceiling fan complete with three aluminium blades down rod, snackel clamp, reel insulator, fan canopy split pin and accessories 230 V, 1200mm sweep with service value not less than 7.8, power consumption not more than 28 watt and minimum air delivery of 220 CMM, BEE 5 star rated, two core PVC insulated copper wire white sheathed of size 0.5 sqmm from fan connector to ceiling rose complete all as specified and directed. NOTE:-(I) Writing MES no in 20mm letter size with black paint etc is deemed to be included in quoted rate. (ii) Old fan deposit in store yard.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed by Engineer-in-Charge.

M&L pipe galvanised iron of size 50 mm dia, light grade ISI marked, complete with fittings laid in trenches/ fixed with poles etc as protection to cables complete as ditrected by Engineer in Charge

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick weithing not less than 17.5 Kg buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 2009 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs) complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

VIJAY BUILDERS (BID ID -3500240)

M/S Kharya Associates (BID ID -3500920)

HARNAM SINGH ANIL SINGH (BID ID -3492544)

kalia constructions (BID ID -3493501)

RAVI TRADERS (BID ID -3500752)

FTH TRADERS (BID ID -3494171)