SPECIAL REPAIR/REPLACEMENT OF ELECTRICAL LT OH LINES/ UG CABLES (PHASE-IV) AT ATS BELAGAVI UNDER GE(AF) SAMBRA

Amount

M&L for XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured heavy duty electric power cable 1100 volts with stranded aluminium conductor of size 6 Sqmm, 2 core laid in trenches or under road complete all as specified and as directed. (Note: Excavation & earthwork shall be measured & paid separately)

All as per Srl item No.1 above but of size 10 Sqmm, 2 core -ditto-

All as per Srl item No.1 above but of size 10 Sqmm, 4 core -ditto-

All as per Srl item No.1 above but of size 16 Sqmm, 2 core -ditto-

All as per Srl item No.1 above but of size 16 Sqmm, 4 core -ditto-

All as per Srl item No.1 above but of size 35 Sqmm, 3.5 core -ditto-

All as per Srl item No.1 above but of size 35 Sqmm, 4 core -ditto-

All as per Srl item No.1 above but of size 70 Sqmm, 4 core -ditto-

All as per Srl item No.1 above but of size 120 Sqmm, 4 core -ditto-

All as per Srl item No.1 above but of size 240 Sqmm, 4 core -ditto-

M & L for cutting of existing bitumen road/ hard standing / PCC for laying of cable/protection pipe complete all as specified and directed.

Excavation in trenches not exc 1.5 mtr wide and not exec 1.5 mtr in depth for foundation or laying pipe lines or cables and getting out as in lhard/dense soill complete all as specified and directed.

Returning, filling in including spreading leveling, watering and well ramming in layer not exc. 25 cm in soft/ loose soil, complete all as specified and directed.

Removing excavated material to a distance not exc 50m and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for galvanised iron steel tubes, ISI marked light grade of 50mm bore for cable protection along the poles under road under drains complete all as specified and directed

All as per Srl item No.15 above but size 80mm bore.

Taking down existing old ACSR conductor from PCC/Steel poles complete all as specified and directed

Taking down existing old cross arms of MS channel or angle sections complete all as specified and directed

Dismantling of old insulators pin/shakle complete and keeping aside for removal complete all as specified and directed

S&F danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with MS clamps, bolts and nuts of approved size for LT 20x15cm size complete all as specified and directed.

M&L for outdoor type LT Feeder piller box of size 600mmx450mmx300mm deep, 415 volts, 3 phase, 4 wire 50 Hz having 04 Nos colour coded aluminium bus bar of capacity 160 Amps mounted on porcelain insulators with suitable number of holes for making connections of cables including 200 Amps porcelain kit kat fixded in box, made out of 3.15mm thick sheet steel CRCA and mounted on frame of suitable size made out of angle iron 45x45x6mm with 4 Nos legs embeded in PCC foundation 300mm below ground level and 300mm above ground level, duly painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, dust and vermin proof, front door with locking arrangement and two earth points by side of the box, cubical type with cable glands, sockets etc and with provision of cable entry from bottom, including painting steel frame and taking out old unserviceable feeder piller box, complete all as specified and directed. Note: Drawing for LT feeder piller box shall be got approved from Accepting Officer before fabrication.

M&L for duct pipe double wall corruugated HDPE 40mm outer dia confirming to IS;14930 (Part-II) of approved colour with fitting for cable protection complete all as specifid and as directed.

All as per Srl item No.22 above but 50mm outer dia -ditto-

All as per Srl item No.22 above but 77mm outer dia -ditto-

Supply and fixing LT panel pillar box cubical type of comprising size (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 240 Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable, foundation is not less than 30 cm below ground level and not less than 45 cm above ground level, legs of panels will be grouted in centre of PCC foundation centre place will be open for connection of Under ground cables with cable glands including provision of following (Note: Drawing for LT PANEL shall be got approved from Accepting Officer GE before fabrication):-

Supply and fixing LT panel pillar box cubical type of comprising size (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 100 Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable, Foundation is not less than 30 cm below ground level and not less than 45 cm above ground level, legs of panels will be grouted in centre of PCC foundation centre place will be open for connection of Under ground cables with cable glands including provision of following (Note: Drawing for LT PANEL shall be got approved from Accepting Officer before fabrication):-

Supply and fixing LT panel pillar box cubical type of comprising size (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 60 Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable, Foundation is not less than 30 cm below ground level and not less than 45 cm above ground level, legs of panels will be grouted in centre of PCC foundation centre place will be open for connection of Under ground cables with cable glands including provision of following (Note: Drawing for LT PANEL shall be got approved from Accepting Officer before fabrication):-

Supply and fixing LT panel pillar box cubical type of comprising size (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 150Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable, Foundation is not less than 30 cm below ground level and not less than 45 cm above ground level, legs of panels will be grouted in centre of PCC foundation centre place will be open for connection of Under ground cables with cable glands including provision of following (Note: Drawing for LT PANEL shall be got approved from Accepting Officer before fabrication):-

Supply and fixing LT panel pillar box cubical type of comprising size (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 100 Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable, Foundation is not less than 30 cm below ground level and not less than 45 cm above ground level, legs of panels will be grouted in centre of PCC foundation centre place will be open for connection of Under ground cables with cable glands including provision of following (Note: Drawing for LT PANEL shall be got approved from Accepting Officer before fabrication):-

Supply and fixing LT panel pillar box cubical type of comprising size (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 60 Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable, Foundation is not less than 30 cm below ground level and not less than 45 cm above ground level, legs of panels will be grouted in centre of PCC foundation centre place will be open for connection of Under ground cables with cable glands including provision of following (Note: Drawing for LT PANEL shall be got approved from Accepting Officer before fabrication):-

M&L for cable route indicator with a welded/riveted disc 10cm dia and engraved with cable with cable route markar made out of angle iron 40X40X40mm thick dug in ground with in and incl PCC 1:3:6 type C1 using 20mm graded aggtegate at approx distance 30 mtr including necessary earth work complete all as specied and directed

S&F in replacement loop in loop out box with transparent lid IP 65 weather proof of suitable size fixed to pole / wall with suitable FI clamp 20mmX3mm nuts,bolts and washers incl provision of 01 no miniature circuit breker (MMCBs) SPN 'C' SERIES, 240 Volts 10KA 06 Amps and incl suitable for 1nos 50/16 sqmm x 3.5/4 core XLPE outgoing cable complete all as specified and directed.

M&L for connection the street light point from loop in loop out box by using a two runs of singal core 1.5 sqmm.PVC insulated sheathed FR Copper conductor cable including PVC conduit/ floxole pipe of suitable dia along with one run of 1.5 sqmm FR copper cable for earth continuity conductor as earth lead for street light complete all as specified and directed.

M&L for earthing to panel / equipments / panels etc with & including galvanised mild steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the earth plate at a depth not less than 1.5 m below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to & including galvanized mild steel strip 32x6 mm as earth lead, including nuts, bolts, check nuts & washers of galvanized iron or steel and riveted/welded to earth plate at one end and other end of strip connected to Panel / equipment body / test point with two Nos nuts bolts or welding with steel structure, GI earth strip encased in and including 40mm bore GI light grade pipe with all fittings from upper edges of earth plate upto 7.5 metre above ground level fixed with and including 25x3mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from earth pit to top of electrode and including funnel, wire mesh, copper lugs etc complete with earth pit in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and 40mm thick RCC (1:2:4 type B1) cover complete all as specified and shown in electrical plate No 3 of SSR Part-I including necessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exc 50m complete all as specified and as directed. Note : GI strip and GI light grade protection pipe 40 mm bore up to 7.5 metre is included in unit rate and beyond that the same will be measured separately and complition after earthing testing below 2.5 ohm.

V.K. Infra Engineering (BID ID -3345621)

M/s PRATAP VIJAYSINGHRAO DESAI (BID ID -3353996)

R. P. Suppliers and Construction Co. (BID ID -3348969)

DHAIRYASIL RAMAKANT DESAI (BID ID -3345881)

metro electrical services (BID ID -3354370)

M/s.GOODWILL ELECTRICALS (BID ID -3353704)

M/s. VIJAY ELECTRICALS (BID ID -3354001)

RAJENDRA KRISHNA SARAF (BID ID -3345012)

SHREE SWASTIK ENTERPRISES (BID ID -3345457)