Civil Works

Amount

Dismantling clearing away and carefully stacking the materials useful for reuse for any thickness of Floor finish and dadooing walls in cement mortar with mosaic tiles/glazed tiles / Cuddapah slab etc., as directed by the departmental officers.

Dismantling the Brickmasonry wall in Cement Mortar and clearing away with carefully stacking the material useful for reuse for any thickness of wall under 3m height etc., complying with standard specification and as directed by the departmental officers.

Dismantling the existing Doors and windows etc., and as directed by the departmental officers.

Dismantling the existing Weathering course with pressed tiles clearing away etc., and as directed by the departmental officers.

Clean and removal of Thorough scrapping of old plastered surface etc., as directed by the departmental officers.

Dismantling, clearing away for any thickness RCC by manual / by using deploying machineries etc., complete as directed by the departmental officers.

Hitech dismantling of RCC elements including suitable heavy machinery,Cranes, tipper and cutting using mechanised diamond rope saw cutting etc., complete as directed by the departmental officers.

Supplying and fixing barricading arrangements with following specification. The vertical post made up of MS Rectangular hollow section of size 100 x 50 x 4.00 mm to a height 14.50m (13.00m above ground level and 1.50m below ground level) and horizontal bracing including cutting to required size and welding the ribs,conveying the pipes to worksite and erecting the same with necessary scaffolding, The post horizontal purlin made up of MS Square hollow section of size 50 x 50 x 4.00mm 11 nos and Rectangular hollow section of 50 x 25 x 4.00mm -5 Nos. including cutting to required size and welding the ribs, conveying the materials to worksite etc. The barricading face should be covered with Pre printed hot dipped galvanized roofing steel sheets (PPGI Sheet) to a height is 13.00m using necessary special screws and bolts etc.The iron materials has to be painted with two coats of SEP over one coat of primer. The rate is inclusive cost of all materials, Labour charges, necessary supports, scaffolding, welding charges and tranportation charges etc. complete complying with standard specification and as directed by the departmental officers.

Installation Charges inclusive of Transportation to site and the Bored pile equipment employed for the works including setting up of pile driving equipment with all accessories and tools at each of the pile location based on the sequence of operation approved by the departmental Engineers irrespective of the location and distance involved in movement of pile driving equipment etc., complete.

Installation of Vertical bored cast in situ RCC piles of basic length 10RM in all types of soil with M30 Grade using Ready Mix Concrete, Supply and erection of reinforcement, shoe, fabrication, including cost of binding wire, cutting, tying, welding and placing the reinforcement cage in correct position, driving and removing the temporary casing pipe of full depth, shifting the plant and equipments from one point to another, carryingout any ancillary work adiacent to piling work, trimming the concrete above cutoff level, cleaning the debris and levelling the site etc, as directed by the Departmental Engineers.The Rig capacity,height of Tower and length of casing pipe etc., must be adequate to take care of change in soil profile. The length of pile for payment shall be measured from top of shoe to the bottom of the pilecap. Testing of Concrete as specified in IS 456/2000 acceptance criteria as per clause 16.1. Frequency of testing as per 15.2.2. Testing to be conducted at both the ends at site as well as RMC plant. Pile driving depth should be decided by the departmental officers at site.

450mm dia pile - having longitudinal reinforcement of 6 Nos of 16# with helical reinforcement of 10# @ 200mm c/c with inner rings of 12mm dia @ 1000mm c/c with lifting hook of 12mm dia required depth.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Upto 2m depth

Earth work open excavation in all soils and sub soils and to a full depth as may be directed except in rock requiring blasting inclusive shoring, strutting dewatering wherever found necessary, depositing the excavated earth at site of work in Places shown by the departmental officers with an initial lead of 10m and lift of 12m, clearing and leveling the site etc. complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling M-sand in layers of not more than 15cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam with specification including premixing the materials with water at OMC in mechanical mix plant carriage of mixed materials by tipper to site laying in uniform layers with pavers in subbase/base course on well prepared surface and compacting with vibratory roller to achive the desired density including cost of materials , labour charges rental for machonery,fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5

Supplying and filling in basement with Stone dust (Quarry dust) in layers of not more than 15 cm thick, well rammed watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kg/mᶾ and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation & Basement

Ground floor

First floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in Cement Mortar 1:5 (One Cement and Five sand) using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

In Foundation and basement

Brick work in Cement Mortar 1:6 (One Cement and Six sand) using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

Ground floor

Brick partition walls of 11 cm thickness using best quality Fly Ash Bricks of 230 x 110 x 70mm size in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground floor

Providing granolithic floor finish of the 50mm thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Laying of screed concrete using Cement concrete mix 1:2:4 ( one cement, two sand and four hard broken stone jelly) using HBGS 6-10mm ISS metal for wearing coat including laying, compacting, finishing and curing etc., complete as per standard specification and as directed by the departmental officers

Paving the top of roof with solar reflective ceramic tiles (required design) of 305x 305x 7mm thick of approved quality and colour laid in cement mortar 1:3 (One cement and three sand) 20mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint ,curing etc., complete complying with the standard specification and as directed by the departmental officers. (The make and brand of the tiles (Johnson endura or equivalent) should be got approved by the Executive Engineer before use on works)

Brick jelly Lime Concrete of 1:2:5 (One Lime,Two Sand and Five Brick ielly ) with 40mm hand broken brick ielly for Sunken portions including dewatering wherever necessary and laid in layers of not more than 15cm thick, well rammed, consolidated and curing etc. complete complying with standard specification.

Paving the floor with best quality Double Charged Vitrified Tiles 800 x 800 x 10mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the tile joint with epoxy grout with surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly etc., complete complying with standard specification. (The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco / RAK which has to be got approved by Executive Engineer before use on works)

Flooring with Quartzite Slab 25mm thick in required areas over a base layer of CM 1:3, 20mm thick and the slab matching with grains patterns and as instructed fixed to correct line, joints well cleaned, grouted with matching colour with approved Cement based grout, cured, etc. The cost includes cost of all materials, labour, wastage, fixing, polishing, including, conveyance etc complete.The Quartzite slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work.

Clading the walls by supplying and fixing of Sandstone 18mm thick in required areas over a base layer of CM 1:3, 10mm thick with Epoxy grouting Cerabond 39 material fixed to correct line,plumb,joints well cleaned, grouted with matching colour approved cement based grout, cured, etc. as directed and for fixing the sandstone in position wherever necessary. The cost includes cost of all materials, labour, wastage, Chemical adhesive, fixing, polishing, including, conveyance etc complete.The quality and colour of sandstone should be got approved by the Executive Engineer before use on works

Clading the walls by supplying and fixing of Quartzite slab 25mm thick in required areas over a base layer of CM 1:3, 10mm thick with Epoxy grouting Cerabond 39 material fixed to correct line, plumb, joints well cleaned, grouted with matching colour approved cement based grout, cured, etc. as directed and for fixing the Quartzite slab in position wherever necessary. The cost includes cost of all materials, labour, wastage, Chemical adhesive, fixing, polishing, including, conveyance etc complete. The quality and colour of Quartzite slab should be got approved by the Executive Engineer before use on works

Clading the walls by supplying and fixing of Black Galaxy Granite Slab 18-20mm thick in required areas over a base layer of CM 1:3, 10mm thick with Epoxy grouting Cerabond 39 material fixed to correct line,plumb,joints well cleaned, grouted with matching colour approved Cement based grout, cured, etc. as directed and for fixing the granite slab in position wherever necessary. The cost includes cost of all materials, labour, wastage, Chemical adhesive, fixing, including, conveyance etc complete.The Granite Slab and other materials to be used shall be got approved by the Executive Engineer concerned before use on work.

Flooring with Agria White Marble Slabs of size 1.20m x 0.90m of 16-18mm thick in required areas over a base layer of CM 1:3, 20mm thick and the slab matching with grains patterns and as instructed fixed to correct line, joints well cleaned, grouted with matching colour with approved Cement based grout, cured, etc. The cost includes cost of all materials, labour, wastage, fixing, polishing, including, conveyance etc complete.The Quartzite slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work.

Cladding the Arch by supplying and fixing of Kelwa White Marble slab 18 to 20mm thick cutout with CNC machinery to curved profiles to suitable curved arch surfaces in required areas over a base layer of CM 1:3, 10mm thick with Epoxy grouting Cerabond 39 material fixed to correct line,plumb,joints well cleaned, grouted with matching colour approved cement based grout, cured, etc. as directed and for fixing the Kelwa White Marble slab in position wherever necessary. The slab shall be fixed to the surfaces using suitable stainless steel clamps fastened to the surface by special stainless steel fasteners 75x10mm dia fixed to the surface using necessary drills/holes and pluged with chemical adhesive/filler. The cost includes cost of all materials, labour, wastage, Anchor fasteners, SS clamps, Chemical adhesive, fixing, polishing, including scaffolding, conveyance etc complete. The White Agria marble slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work.

Cladding the walls by supplying and fixing of Kelwa White Marble slab 18 to 20mm thick cutout in required areas over a base layer of CM 1:3, 10mm thick with Epoxy grouting Cerabond 39 material fixed to correct line,plumb,joints well cleaned, grouted with matching colour approved cement based grout, cured, etc. as directed and for fixing the Kelwa White Marble slab in position wherever necessary. The slab shall be fixed to the surfaces using suitable stainless steel clamps fastened to the surface by special stainless steel fasteners 75x10mm dia fixed to the surface using necessary drills/holes and pluged with chemical adhesive/filler. The cost includes cost of all materials, labour, wastage, Anchor fasteners, SS clamps, Chemical adhesive, fixing, polishing, including scaffolding, conveyance etc complete. The White Agria marble slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work.

Paving the floor with best approved quality Chisel dressed stone slab of size 600mm x 600mm, 40mm thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the stone with required cement slurry and laid in true right angles with minimum possible width of joints and pointing etc., The chisel dressed stone slabs and other materials to be used shall be got approved by the Executive Engineer before use on work, etc., complete as per standard speicification.

Paving the floor with best approved quality Chisel dressed stone slab of size 1200mm x 600mm, 50mm thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the stone with required cement slurry and laid in true right angles with minimum possible width of joints and pointing etc., The chisel dressed stone slabs and other materials to be used shall be got approved by the Executive Engineer before use on work, etc., complete as per standard speicification.

Supplying,erection and fixing of Granite Chisel dressed mobile stones of size 38"x 38" with Height of 36" for Compound Wall including cost of granite blocks, Labour charges for cutting,dressing to the required size and shape etc., The chisel dressed stone blocks and other materials to be used shall be got approved by the Executive Engineer before use on work, etc., complete as per standard speicification.

Flooring with Self design Joint free rectified Ceramic Tiles of size 305 x 305 x 8mm laid over 20mm thick cement mortar 1:3 (One cement and Tree sand) base mortar over the existing slab / floorincluding cutting the tiles to the required size with special cutter wherever necessary, laying in positionand and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg./sq.m.etc., complete complying with standard specification. (The make and brand of the tiles should be Johnson/ Kajaria / Somany / Nitco/ RAK or Equivalent which has to be got approved by executiveEngineer before use on works)

Dadooing walls with Joint free rectified Colour designed digital print ceramic tiles, with borders, with size of 300mm x 600mm x 10mm and above setin Cement Mortar 1:2 (One Cement and Two sand) 20mm thick andpointing the joints with white cement mixed with colouring pigmentsat the rate of 0.40 Kg. / sq.m. nbatly in all floors, curing, etc, complying with standard specification and as directed by thedepartmental officers. (The make and brand of the tiles should belike Johnson / Kajaria / Somany / Nitco / RAK or Equivalent whichhas to be got approved by Executive Engineer before use on works)

Supplying 18 to 20 mm thick white jet black granite partition slab for urinals of 1200x600 (Avg) mm size fixing to wall using 3Nos.of suitable chromium plated brackets with CP bolt and nets, washers, cutting to required shape polishing to all the expose and surfaces and edge grinding etc, complete as directed by the dept officers.

Providing and Fixing of PVC Trims (Corner beeding) at the outer corner profiles of the tiles including cost of material, labour and handling etc. as directed by departmental engineers at site of work and as per standard specification.

Manufacturing, Supplying and fixing of GRC Name panel with following specifications: The GRC Components made from, 53 Grade White Portland Cement,The silica sand (1.2mm size passing through 150micron sieve), Alkali Resistant Roving Fibre from Nippon (ARG Fibre), Acrylic Polymer,Mould made by FRP/GRP,GRC Screen thickness of 18-25mm using Spray technology etc., charges for conveyance to work site, fixing in position using necessary lifting equipments, using necessary labour for fixing and other incidental charges etc.,complete complying with standard specification and as directed by the departmental officers.

Manufacturing, Supplying and fixing of GFRC Column panel with with following specifications: The GFRC Components made from, 53 Grade White Portland Cement,The silica sand (1.2mm size passing through 150micron sieve), Alkali Resistant Roving Fibre from Nippon (ARG Fibre), Acrylic Polymer,Mould made by GFRC Screen thickness of 18-25mm using Spray technology etc., charges for conveyance to work site, fixing in position using necessary lifting equipments, using necessary labour for fixing and other incidental charges etc.,complete complying with standard specification and as directed by the departmental officers.

Paving the floor with Tactile paver of New Tek BT Yellow colour ceramic tiles of size 300x300x15mm for guiding/warning Tactile signal for persons with vision impairment in all floors over a base layer of Cement mortar 1:3 (One cement and Three Sand) 20mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg/Sq.m neatly in allfloors,curing etc.,complete complying with standard specification and as directed by the departmental officers.

supplying of manual foldable wheel Chair with fixed armrest and footrest,Cushion seat and back,Black Colour Rexin finish with standard specification and as directed by the departmental officers

supplying and fixing of braile signage boards of size 6” x 9” as with standard specification and as directed by the departmental officers

Providing semi nosing at the edges of the vertical space with neat finishing etc complete with standard specification and as directed by the departmental officers.The cost including higher charges of machines and labour charges etc complete

Supply and fixing of GYP Board false ceiling using 12.5 mm thick of approved quality and design suspended from the ceiling using "U" shaped Galvanised iron channels at 1.20 M centre to centre on both longitudinal and cross direction for vertical support and fixing "U" shaped G.I channels at 0.90 m centre to centre on longitudinal direction respectively for horizontal support by using T.W reapers at corners and at intermediately and fixing of plaster of paries on the panel provided as per design / patttern given by the site officer and finishing the ceiling surface with some plaster of paries materials etc. Necessary openings should be made for providing spotlights, florescent tubes in the ceiling by using plywood 12 mm thick and opening should be covered with Acrylic panel complying with standard specification and as directed by the departmental officers etc. complete. All the materials should be got approved before use on work by the Executive Engineer.The rate is including two coats of plastic emulsion painting over the wall coat primer etc., complete.

Providing & fixing Cornice with gypboard 150mm wide of suitable design. The joints shall be finished with joint paper tape by using joining compound of India Gypboard ltd. The ceiling surface shall be painted with three coats of approved quality plastic emulsion over a coat of primer etc. complete as directed by the departmental officers.

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick mixed with bonding agent Cebex 112, Zydex-Zycrete 2X or Other equalent compound conforming to BIS at 200ml of One cement bag (50Kg) for increased workability and air entrainment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Replastering the old walls and floors with cement mortar 1:3 (One cement & three sand) 20mm thickness mixed with bonding agent Cebex 112, Zydex-Zycrete 2X or Other equivalent compound conforming to BIS at 200ml of One cement bag (50Kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Supplying and applying Putty with two coats of plastered wall surface of first class quality and of approved including thorough scrapping, clean removal of dirt wherever required etc., complete complying with standard specification.

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (water proof abrasive sheet) the same after it is dry and finishing the surface smoothly,etc.,complete complying with standard specifications and as directed by the Departmental Officers.The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc.,complete. The putty should be got approved by the Executive Engineer before

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick mixed with bonding agent Cebex 112, Zydex-Zycrete 2X or Other equalent compound conforming to BIS at 200ml of One cement bag (50Kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Providing the texture finish to the newly plastered wall with ready made texture putty with patterns at all levels including the cost of coating, labour charges and other incidental charges etc., complete as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and fixing Teak Wood frames for doors Windows and Ventilators using required MS angles, flats and rods of approved design and as directed by the departmental officers including cost of MS Grills, labour charges and cost of one coat of red oxide primer with labour charges for priming coat etc. complete complying with standard specifiction.

T.W Scantlings above 2m below 3m

Supplying and fixing in position of Teak wood door shutter using spl quality teak wood planks of 40mm thick panelled doors with required raw materials, Brass hinges, Brass tower bolt, ornamental Brass handles, Door stopper, Door closer, Brass aldrops and bush with suitable locking arrangements etc. The rate should be inclusive of cost of materials, labour charges for wrought and put up the doors with kadasal charges and transporting charges etc complete complying with standard specification and as directed by the Departmental officers.

Polishing the teakwood panelled door / solid core flush door shutter with best melamine varnish finishing including labour charges for scrapping the existing panelled throughly on both sides of the door, sand papering without affecting the teakwood plank grooves and natural design with preparation of surface using sand paper and finishing the smooth wooden surface and applying of melamine polishing on the teakwood panelled door/ flush door surface using spray machine on uniform layer of smooth surface formed without any air bubbles after finishing the work etc., the rate inclusive of cost of materials ,labour charges ,transportion charges, labour for scrapping charges, etc complete complying with standard specification and as directed by the departmental officer (the materials quality are approved by the EE Before use of work.

Providing factory made pre-laminated FPVC (Formed Polyvinyl Chloride) Door Frame of the size 105x40mm with a wall thickness of 10mm made out of extruded rigid FPVC profile mitre joined with 6Nos. of 5mm long screw. The door frame shall be fixed to the wall by using 80mm long screws through the frame with the help of PVC fasteners of 3Nos. to be provided for each vertical member, GI stiffeners of ('U'channel of size 29x9,1mm, 150mmlong) -3Nos. at hinge point, frame reinforcement of ('U'GI channel of size 46x22x0.6mm), bottom tie rod of('U'GI channel size of 15x15x1mm),etc., complete complying with the standard specification. The door frame should be got approved from the Executive Engineer before use on work

Providing of 35mm thick factory made pre-laminated ABS (Acrolynitrile Butadiene Styrene) Door Shutter moulded in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by 32 x 32mm -2 Nos., for vertical made out of LVL (Laminated Veneer Lumber), core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges -3 Nos., for each shutter and ISI make SS round lock complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work

Supplying,fabricating and fixing in position of aluminium anodized natural colour matt finish door fully PLB Board 12 mm thick Sliding door using rectangular aluminium box section of fsizes of frame section 101.60 x 44.45 x 3.18 mm @ 2.399 Kg./M Shutter Sections Top and Middle Section 50 x 44.45 x 2.50 mm @ 1.292 Kg./M, Bottom Section 100 x 44.45 x 2.50 mm @ 1.974 Kg./M, Vertical Style 50 x 44.45 x 2.50 mm @ 1.292 Kg./M with necessary accessories such as aluminium clips, handles,lock and sliding channel with wheel set including all materials, labour and power consumption charges required for fabrication if necessary clipping, dismantling materials necessary holes in RCC column beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc. complete.

The aluminium surface is to be anodized with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than 15 microns (Fifteen) for all sections. All the materials should be got approved by the Executive Engineer before fixing in position as directed

Supplying and erecting Gear Operated Type rolling shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc.,complete complying with standard specification.

Supplying and Erecting Gear Operated Type Rolling Grills with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc

Designing the 12mm thick toughened glass panel work with groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept Officials.)

Designing the 12mm thick Hinged Toughened Glass Door work as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept Officials.)

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss.

The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing of M.S. grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including cutting the members, welding, grinding, one coat of priming coat using best approved quality red oxide primer, dismantling of walls / concrete if necessary, fixing and finishing the dismantled portion to original condition etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing specially curved monolithic Sand Stone ballustrades Handrails of approved design and pattern made out of Sand stone posts of size 75 x 75 mm and 650 mm height and Specially carved Sand stone Handrails overall size 150mm and 75mm thick fixed in position with necessary drilling and chemical grouting to the specified spaceing and alignment etc., complete as directed by the departmental officers. ( The colour, shade of sand stone and the pattern of carving of the ballustrade should be got approved by the Executive Engineer before use on works.)

Supplying and fixing specially curved monolithic Marble Stone ballustrades Handrails of approved design and pattern made out of Marble stone posts of size 75 x 75 mm and 650 mm height and Specially carved Marble stone Handrails overall size 150mm and 75mm thick fixed in position with necessary drilling and chemical grouting to the specified spaceing and alignment etc., complete as directed by the departmental officers. (The colour, shade of marble stone and the pattern of carving of the ballustrade should be got approved by the Executive Engineer before use on works.)

Removing, Renewing and refixing the old Stainless Steel Hand rails in original position with required raw materials etc., The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance and electrical charges, etc. complete as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304 Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc.complete

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Supplying and fixing Stainless Steel Pipe with Ornamental design with new Stainless Steel Pipe. The top of the pipe with 50mm dia stainless steel and 20mm dia pipe at regular interval of horizontal pipe with 20mm thick with a base plate 60x10mm rigidly welded through entire Length to be laid 50mm stainless steel pipe for balustread from the begining to tall end at a interval of 95cm c/c with a minimum height of 100cm. Bottom of this balustread to be Linted with a base stainless steel plate of 75mmx2mm thick. This should be welded in every supported pipe at the junction. The SS are to be welded with electrode specified for stainless steel work. The above rates are inclusive of all materials labour and hire charges for welding machines conveyance neat finishing etc., complete complying with standard specification and as directed by the departmental officer.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

160mm dia

110mm dia

supplying and fixing of Pre printed hot dipped galvanized roofing steel sheets for front curved design with the following specifications. The material should be of PPGI tile profile with approved colour of 0.47mm thick having coil width 1170mm sheet width 1120mm and effective width 1035mm.The steel should be G.I. base pre painted hot dipped galvanized steel, sheet and to be fixed with screws, plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z120 GSM paint thickness at top to be 18 to 20 microns and tensile yield strength of 345 MPA. The surface paint reflection should be glossy finish (optional matt finish). The rate inclusive of cost of all materials, bending charges for sheet with wastage of cutting for ornamental design, fixing and alignment to the roof portion, dismantling is required and to do to the original conditions, neat finishing etc., complete complying with standard specification and as directed by the departmental officer.

Providing two legged scaffolding using 48.30mm outer diameter heavy duty M.S pipes over all height 3.00m the distance between two kegs being 1.25m and the spacing of the post being 2.00m in each rows and providing platform with country wood plants using 40mm thick silver oak and 1.00 m wide in complete from with horizontal bracing @ 1.50 c/c vertical direction and with cross bracing using same 48.30mm diameter including cutting, threading assembly with one coat red oxide primer. Labour charges cost of special such on large plate, shoe, catcher, coupling, bolt and nut transport charges and handling charges. The bottom of vertical post shall rest on 300 x 300 x 70mm, 1:2:4 concreter base as per the standard specification.

For a height of 3m

For a height of 5.50m

For a height of 13m

For a height of 20.50m

Providing Ornamental elevation Mandapam of Hexoganal shape of 3 segments with smooth finishing including of ornamental band in the bottom & top portion, ornamental curved band to a average height of 1m to give an aesthetic look, to a height as shown in sketch, the decoration of khalasam height of 0.60m is fixed on the top of the mandapam using with necessary cement mortar 1:2,cement concrete, Skilled Sthapathies Labourers and including Plastering with Cement mortar 1:3,20mm thick, Interior and Exterior finishing with two coats of white putty and ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt etc., excluding scaffolding charges etc., The rate inclusive of all materials, labourers, etc, Complete Complying with standard specification and as directed by the departmental officers.

Supplying and fixing Decorative Mural Work made out of translucent marble stone pieces of suitable colours, cut, carved and finished into various sizes and shapes depicting the facial Portrait/graphical sketch of Perarignar Anna and Muthamizh Arignar Kalaignar over RCC wall surface including necessary provisions for backlighting etc complete. The Mural work shall be fixed over the back ground wall using suitable adhesives. The rate is inclusive of cost of all materials, labour charges for cutting, Chiselling and carving of marble stones, fixing in position, cost of scaffolding etc complete,exclusive of all taxes. The Mural work shall be got approved by the departmental officers.

Providing and Laying Rubbed moulded paver block paved driveway including supplying 80 to 83mm thick pre-cast Factory made Designer Concrete block of approved size, Shape and colour manufactured by table vibratory compacting having face layer of concrete mixed with white cement and color pigment not less than 5mm thick and base concrete with grey cement prepared monolithically. In the paver blocks top Surface White Cement & top Layer Polish with Lacquer Coat shall have peripheral chamfer, with average crushing strength not less than 30N/Sq.mm as per IS 15658 - 2007 Part – 1 (1986), maximum water absorption of 2% after 10 minutes and 5% after 24hrs.as per BS 1881,maximum dimensional deviations of +/-2mm on length & width and +/- 3mm on thickness. etc., complete complying with standard specification and as directed by the deparmental officers.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of 75mm thickness in RCC 1:2:4 (one cement, two sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

Supply and fixing of stored pressure ABC (Mono Ammonium Phosphate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

WATER SUPPLY & SANITARY ARRANGEMENTS Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

40mm dia G.M. Gate Valve

Supplying and fixing in position 15mm dia following taps (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Executive Engineer before use on the works)

Long body tap

Supplying and fixing in position 15mm dia two way bibcock (heavy duty) with Health faucet of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position Indian make of approved quality and brand Special Type Mirror of size 1000 x 780mm of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing in position best quality and approved make under counter oval type wash hand basin of size 560 x 450mm with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc.,complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc.,complete complying with standard specifications.(The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Nahani Trap of size 100 x 75mm

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

110mm dia

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

PVC Elbow

110mm dia

PVC Elbow with Door

110mm dia

PVC Tee

110mm dia

110mm dia

PVC bend

110mm dia

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works)

110 mm dia

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, SS clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works.

20 mm dia

25 mm dia

40 mm dia

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements

UPVC Elbow

40mm dia

25 mm dia

20 mm dia

UPVC Tee

40mm dia

25 mm dia

20 mm dia

UPVC Reducer

40x25mm dia

25 x 20 mm dia

20 x 15 mm dia

UPVC Reducer Elbow

40x25mm dia

25 x 20 mm dia

20 x 15 mm dia

UPVC Reducer Tee

40x25mm dia

25 x 20 mm dia

20 x 15 mm dia

UPVC Union

40mm dia

25mm dia

Construction of Inspection chamber or manhole of the following size including necessary earth work excavation in all soils to full depth as may be directed with sand filling at bottom of the chamber for 10cm thick, concreting CC 1:5:10 using 40 mm guage HBGs jelly 10 cm thick and sode walls 9" thick brick work in cement mortar 1:5 using II class chamber burnt bricks of size 9" x 43/8" x 23/4" filling the size of foundation with excavated earth, plastering with cm 1:3 20mm thick for inside and bottom and making necessary benching with brick jelly cement concrete to the required slope and fifnishing neatly etc., complete.

Supplying and fixing in position of Steel fibre reinforced cement concrete (SFRC)manhole / inspection chamber cover slab with following frame sizes including necessary labour charges for fixing the frame in position over the cement mortar base and finishing the joints etc. complete as directed.

600x600mm cover slab

Supplying and fixing of PVC mould CI Steps of approved quality including dismantling masonry wherever necessary and redoing the damaged portion to original condition

Supplying, fixing and position of PVC Water Tank for required capacity with accessories, etc., complete complying with standard specifications

Manufacturing and placing RCC Well rings of 0.91m dia internal diameter 40mm thick in RCC 1:1.5:3 (One cement,One and half M sand and Three HBGS Jelly 12 to 20mm gauge) including necessary reinforcement, rendering smooth with cement the inner and outer surface of the ring etc., the rate is inclusive of cost of rings, conveyance chagres in to the well and erecting charges etc., complete complying with standard specifications

Lawn & Gardening Conveying and Collecting the excavated earth away the same to outside by lorry to a lead of not less than 3km limit including loading and unloading charges and dumping in low place and levelling etc., complete complying with standard specification and as directed by the departmental officers

Supplying, spreading of top soil. Uprooting the weeds from the pit area. Supply of Red soil, carriage loading and unloading and stacking at site etc.complete.

Supplying and mixing of Farmyard manure, DAP, Super phosphate, Neem and fertilizers in the desired proportion in the pits, flooding with water and levelling etc.complete.

Supplying and planting of Cleodendron/ Acalypo Red and green as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of Royal palms of 12 to 15feet as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of Ficus panda of 2 feet as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of Plumeria of 6 feet as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of Native Trees (Gulmohar, Cassia fistula, Mango, Coral tree, Ceselpinnia, etc of 10 to 12 feet as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of Mirchimeri gold of 6 feet as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of Terminalia of 8 feet as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and laying of Mexican grass as directed by the Engineer-in-charge and refilling the soil with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of shrubs as Duranta gold/(Exora)directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 30 days from the date of planting works.

Supplying and planting of Alamanda as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 30 days from the date of planting works.

Supplying and planting of percuria as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 30 days from the date of planting works.

Supplying and planting of Euphorbhia/ Adenium/ Vinca/Exora as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 30 days from the date of planting works.

Supplying and planting of Travellers palm as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 30 days from the date of planting works.

Supplying and planting of Rhapix palm as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of Arecca nut palm as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of pendanus as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of Bonsai Trees as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and planting of Ficus Benjamina ball shape Trees as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days.

Supplying and planting of Flowering plants as directed by the Engineer-in-charge digging holes in ordinary soils and refilling the same with manure, flooding with water and dressing removal of rubbish, surplus earth if any with all leads and lifts, also maintenance of plants for a period of 90 days from the date of planting works.

Supplying and positioning of polished or unpolished Pebbles and boulders as directed by the Engineer-in-charge etc., complete

Supplying and positioning of stone sitting granite tablets etc., complete

Supply and installation of 45 W 5700K LED post top lantern of IP65 on a 3 mtr decorative hot dipped galvanised mild steel step pole with grey powder finish with top of dia 76 mm with a opening window of 300 x110mm for terminal connections and mounting accessories with necessary concreting structure with the J bolt provision for mounting the pole with the necessary electrical connections Like Make:Havells RUBY LED POST TOP Model:RUBYPT45WLED757PSYMTOPC ,Like pole:ECO Pole 3M Havells /Eq.

Supply and installation of 45 W 5700K LED post top lantern of IP65 on a 4 mtr decorative hot dipped galvanised mild steel step pole with grey powder finish with top of dia 76 mm with a opening window of 300 x110mm for terminal connections and mounting accessories with necessary concreting structure with the J bolt provision for mounting the pole with the necessary electrical connections Like Make:Havells RUBY LED POST TOP Model:RUBYPT45WLED757PSYMTOPC ,Like pole:ECO Pole 4Mtr Havells /Eq.

Supply and installation of 40 W 3000K LED post top lantern of IP65 on a 3 mtr decorative hot dipped galvanised mild steel step pole with grey powder finish with top of dia 76 mm with a opening window of 300 x110mm for terminal connections and mounting accessories with necessary concreting structure with the J bolt provision for mounting the pole with the necessary electrical connections Like Make:Havells RUBY LED POST TOP Model:RUBYPT40WLED757PSYMTOPC ,Like pole:ECO Pole 3Mtr Havells /Eq.

Supply and Installation of UFO shape design IP65 LED Bollard of 10 W of 3000K on a concrete block of (lxb) 1'x1' or 10''/8'' round blockand 1-1/2 ft height with necessary Anchor fastner bolts and electrical connections Like Make:Havells/Eq. ,Like Model:

Supply and Installation of MOUNT LED design IP65 LED Bollard of 10 W of 3000K on a concrete block of (lxb) 1'x1' or 10''/8'' round block and 1-1/2 ft height with necessary Anchor fastner bolts and electrical connections Like Make:Havells /Eq.,Like Model:

Supply and installation of Regal chandelier 6LS E14 Honey GLD with a 6 Nos of lamp base of E14 and with 5 W LED filament lamp of amber colour with necessary Electrical Connections Like Make: Havells /Eq. Like Model:LHFHAWCITB1D005

Supply and installation of Regal wall light 1 LS E14 Honey GLD with a 1 No of lamp base of E14 and with 5 W LED filament lamp of amber colour with necessary Electrical Connections Like Make:Havells /Eq. Like Model:LHFHAWCBTB1D005

Supply and fixing of RANGER 45W DMX 25° G1 RGB LED fitting including necessary connecting cables for power supply and DMX control with necessary Electrical Connections Like Make:Havells /Eq.

Supply and fixing of Lineate 12W DMX 30°x65° Wall Washer RGB LED fitting including necessary connecting cables for power supply and DMX control with necessary Electrical Connections Like Make:Havells /Eq.

Supply and fixing of Lineate 24W DMX 25° Wall WasherWall Washer RGB LED fitting including necessary connecting cables for power supply and DMX control with necessary Electrical Connections Like Make:Havells/Eq.

Supply and fixing of Lineate 12W DMX 25° Wall Washer RGB LED fitting including necessary connecting cables for power supply and DMX control with necessary Electrical Connections Like Make:Havells /Eq.

Supply and fixing of Lineate 40W DMX 25° LED wall washer RGB LED fitting including necessary connecting cables for power supply and DMX control with necessary Electrical Connections Like Make:Havells /Eq.

Supply and fixing of Lineate 24W DMX 30°x65° Wall Washer RGB LED fitting including necessary connecting cables for power supply and DMX control with necessary Electrical Connections Like Make:Havells /Eq.

Supply and installation of the LED flood light of 3000K of 10W with anchor fastners on wall or ceiling with necessary electrical connections. Like Make:philips/Eq. Like Model:BVP101 20

Supply,Erection and Comissioning of 12 Mtr High Mast post with motorised provision for mounting of 10 nos of 200 Watts LED flood light fittings including foundation,erection testing and commissioning

Supply and fixing of 250 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply of Three phase 50 KVA High Grade Voltage Stabiliser for the installation with features:Low & high Voltage Cutoff Protection Range from 380-480V each mounting cabinet design-Elegant and easy to install wit hintegrated circuit technology for protection on thermal overload Protection.

Cables,glands and terminations Supply and Laying of 3 1/2 x 185 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland for 3-1/2 x 185 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3-1/2 x 185 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and providing cable end termination of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and Laying of 3 1/2 x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and Laying of 3 1/2 x 150 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland for 3-1/2 x 150 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3-1/2 x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and Installation of 80W garden speaker with 70 Hz to 10 kHZ frequency , 4 ohm at 70 / 100 V(10w,20w, 40w, 80w taps) impendence, dispersion 360 degree horizontal, 50 degree vertical dipression, power handling 80w@ 70/100V. Make:Bose/Eq. model No:Free space 360p seriesIII

Supply and Installation of 2000W 4 channel amplifier with configure supports 2 /4/8 ohm and 70/ 100V loads, mono mode 500W (2ohm & 4ohm) output power300W (8ohm), frequency response20HZ-20KHZ,DSP functions bose loudspeaker EQ, mixer/ router, speaker arrayeq inputEQ,delay limmiting, signalgenerator. Make:Bose/Eq. Model: PM 4500

Supply and laying of 2 core 1.5 sq.mm shielded multistand loudspeaker copper cable in existing HDPE pipe on ground . Make:Orbit/Eq.

Supply and Installation of 5 KVA servo Voltage stabilizer.Make:Studiomaster/Eq. Model No:SVC 5000

Supply and Installation of 36U M.S. Audio equipment Rack with consists of all equipments and other accessories with door lock/ key facility and front side acrylic sheet etc for safety condition. Make:Custom /Eq.

Supply and laying of 50mm Dia HDPE black hose in ground at a depth of 0.75 meter and refilling the earth to make good.

Supply and Installation of dynamic handheld microphone with table stand and 20m mic cable. Make:Shure/Eq. Model No:Beta58A

Supply and Installation of UHF wireless handled microphone, touch on / off button,receiver and table stand for holding mic. Make:Shure/Eq. Model No:SLX2/Beta 58 + SLX 4 IN

Supply and laying of concreating and masonary work at a depth of 0.75m for fixing garden speaker with base plate welding. Make:Custom /Eq.

Supply and Installation of 250W portable PA system with 3 microphone inputs with MIC1 priority,inputs for CD & Aux sources,Built in MP3 player with USB, SD/MMC card reader,bluetooth facility and remote control. Make: Ahuja/Eq. Model No: XPA-3010 DP

Supply and Installation of PA lectern system with built in speaker consisting of 3 nos 6.5" coated dual cone speakers,built in VHF wireless receiver,digital recorder cum MP3 player.Make:Ahuja/Eq. Model No:WSL-2500R

Supply and Installation of media player to play files from CDs & hi res MP3, WAV/ FLAC, WMA & DSD files alike, clear & noiseless music with no vibrations. Also equipped with a USB drive The player comes with 1 gold plated analog RCA output and 2 digital outputs (optical and coaxial) connectivity to pre amplifier, integrated amplifier, stereo receiver or AV receiver. Make:NX audio/Eq. Model No:MPC 5500

Testing and Commissioning of garden speaker PA system including programming of digital amplifiers, allignment of garden speakers , cables, connectors and special purpose power amplifiers etc.

Supply and Installation of 4MP IP outdoor bullet Camera ,WDR 3.6 mm Fixed lens. Make:D-Link/Honeywell Model No: :DCS-F4714

Supply and Installation of 4MP IP PTZ Camera with 1080P,WDR 25XZOOM, IRH. 265/H.264 PoE standard.Make:D-link/Eq. Model: DCS-F6917

Supply and installation of 16 channel Network Video recorder , H.264/MJPEG dual code decoding upto 200 Mbps incoming bandwidtht support 2 SATA HDDs up to 8 TB . Make : D-link/Eq.

Supply and Installation of 8-port poE 2 Gigabit managed switch, which supports IEEE802.3 af/at poE standard. Make: D-link/Eq.

Supply and Installation of 4U wall rack, with front glass door with lock and key facilities. Make: D –link/Eq.

Supply and Installation of 8TB built in Hard Disc Drive.Make: Seagate/Eq.

Supply and laying of CAT6 cable in 1” PVC pipe .Make:D-link/Eq.

Supply and run of 25mm dia. PVC rigid pipe on wall and ceiling.

Supply of 43 inches LED TV with following features:1. USB Input 2.HDMI Port 3.Clear audio+ 4.Motion flow XR 200 5.Full HD 1080 Make : SONY/Eq. Model No:W662F

Supply and Installation of 0.6 KVA UPS with suitable 12V,7.2Ah, batteries.Make:APC /Eq.

Supply and laying of 6 core outdoor OFC Cable.Make:D-Link/Eq.

Supply and erection of 4”inch dia and 6-meter height Heavy duty GI post with 6 feet depth concrete work with 16 mm J-Bolt fixing andNecessary masonry work.

Supply and laying of 50mm Dia HDPE black hose pipe in ground at a depth of 0.75 meter and refilling the earth to make good.

Supply and Installation of wall mount bracket for PTZ camera.Make:D-Link/Eq.

Supply and Installation of 3 Mtr SC/LC fiber patch Cord.Make:D-link/Eq.

Supply and Installation of 6 port fiber patch panel,rack mount with all accessories pigtail Included.Make:D-link/Eq.

Supply and Laying of 20Mtrs HDMI cable with HDMI connectors with PVC pipe and accessories.Make: MX/Eq.

Supply and Installation of 10/100/1000 media converter for connecting OFC and cat6 cable. Make:D-link/Eq.

Supply and fixing of CAT6 2 Mtr. patch cord Make: D- link/ Eq.

Supply and Installation of 6U wall rack with front glass door and lock & keys. Make: D –link/Eq.

Supply and Installation of RJ 45 I/O with back Box for cameras .Make:Dlink/Eq.

Testing, Programming and commissioning of software for the Cameras, Alignment of Cameras, Naming of Cameras, Setting of NVR, TV Monitor with HDMI cable , Video cable, BNC Connectors and Power adopter for Cameras RF Modulators , I/Os etc.

GST at 18%

Sri Balaji Constructions

P MANICKAM AND CO