Proposed Beautification of Valpoi Constituency with Design,supply and installation of 9 mtr four arm pole,12.50mtrs,9mtrs six arm high mast etc.At ward no.01 to 10 of Valpoi Municipal Council

Amount

Supply, installation, testing and commisioning of 12.5M high mast shaft in two sections suitable for wind speed 44m/sec. with head frame, luminaries carriage suitable to install 6-8 nos. of luminaries in symmetrical arrangement, lightning finial along with Supply of Accessories required such as double drum winch, 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box etc. make: Trainsrail, wipro,Volmount,Lysaght.

Supply, installation, testing and commisioning of 9M high mast shaft in Single sections suitable for wind speed 47m/sec. with head frame, luminaries carriage suitable to install upto 6 nos. luminaries in symmetrical arrangement, lightning finial,along with Supply of Accessories required such as double drum winch, 5mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box etc. Make: Transrail, Wipro ,Volmount,Lysaght.

Supply, installation, testing and commisioning of LED flood light 350Watts luminaire with secondary optics made in pressure die cast alumnium housing with toughened glass and high poweer LED's and secondary lenses with IP66 protection. with 10KV SPDand heat sink for 350W LED, make:Atilite,Transrail, Wipro, Oasis. Conforming to UL/ FCC Class A, CE standards.

Supply of foundation bolts 6xM24x850mm manufactured from special steel along with nuts, washers, anchor plates and templates as directed by the engineer incharge.

Supply and installation of LED Single dome aviation obstruction light as directed by the engineer incharge

Supply of outdoor stand mounted feeder pillar with 32A TPN MCB incomer, single dial timer, 25A cotactor for automatic switching of luminaries , power tool control with 2 no. 9A contactors and raise lower push button, incoming 35 sq.mm and outgoing 16 & 2.5Sq.mm terminals with outgoing mcbs 6 nos.

Supply and installation of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.4 core 16sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (a) In soily strata

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 4 core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade complete as required 4 x 16 Sq. mm.

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipe etc. with charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. (a) In soily strata

Supplying and laying 25 mm x 5 mm GI strip in 40 mm dia GI pipe from earth electrode as required

Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size 2) 3 Core 1.5 sq.mm

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. (a) All types of Ordinary rock including all types of laterite rock, blasting prohibited

Providing and laying in position ready mixed concrete (RMC) High Performance Concrete per MORTH clause 1715 manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineer-in-charge. All works upto floor V level M-25 grade of concrete

Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Supply and fixing of 32A Kit Kat fuse unit per phase along with fixing of the fuses over wooden board and other required accessories mounting the arrangement over the electriciyt Department Pole.

Supply Installation, testing and commissioning of 9 m high hot dipped galvanised conical poles with 1000mm Street light with 4arm bracket made from 40 mm. Dia ‘B’ class G.I. Pipe, 1.2m. in length along with pole cap of 300mm length and 80 mm dia.(Suitable to pole top) duly welded having bottom dia. from 155 to 170 mm, top dia.from 65 to 75 mm with suitable 4nos. M24 X 750 mm J type foundation bolts complete with all required accessories. Make Wipro, Transail,

Supply, installation, testing and commissioning of 150W Sleek Aerodynamic high efficiency Led Street light housing with pressure die cast Aluminium powder coated, excellent heat dissopation ensureslong service life and high performance of led street light. Ultra high efficiency, non yellowing glass lens optics with IP66 protection. Led of make Philips/ Osram - high efficiency COB. CCT 5700K / 6000K, Efficacy 120lm/W, CRI 80/90. with integral driver.. Make Crompton,Transrail,Wipro,atilite, Oasis,

Supply , Installation, Testing and commissioning of Outdoor double door IP54 Cubical Panel with cubical box compartmentalized provision to mount incoming and outgoing MCB along with the supply of the following no(i)R LED indicating Lamp(make Esbee)-1 No (ii)6A,Toggle Switch-1 No. (iii)32A DP Contactor -1no. c) 24hr Timer with control MCB. - 1no. (iv)Neutral Link, 30A, 6 way-01 No. The Panel box is to be constructed with 16SWG G.I sheet along with paint with one coat of red lead paint and 2 coats of enamel paint.The cubical panel should be mounted on the 9mtr pole at distance of 1.5 mtr or above the ground level with suitable arrangement as directed by Engineer In-charge complete as required.

Supply and Laying of PVC wire 2C X 4Sq.mm 1.1KV grade for service connection

SITC of artistic a set of 3 animals form to be made in translucent polymer of special grade so that uniform glow of the desired colour is achieved from the surface of the polymer. The polymer to be sculpted/formed in the desired artistic shape of illuminated deer shaped sculpture (Male, Female and Baby deer) . These should artistically be installed in a form to create glow and aesthetics to these unique elements of nature. These animal forms to be illuminated using special looped LED lights embedded inside the polymer to provide effective and natural looking glow to the animal form. Size of the deer should be L20 x W12 x H15 inch (Sitting), L27 x W10 x H28 inch (Without corners), L27 x W10 x H33 inch (With corners). DC24V IP67 LED Driver should be provided seperately. Each animal should be installed on concrete base structure using anchor bolt.

SITC of artistic animal form to be made in translucent polymer of special grade so that uniform glow of the desired colour is achieved from the surface of the polymer. The polymer to be sculpted/formed in the desired artistic shape of illuminated Squirrel shaped sculpture . This should artistically be installed in a form to create glow and aesthetics to these unique elements of nature. These animal forms to be illuminated using special looped LED lights embedded inside the polymer to provide effective and natural looking glow to the animal form. Height of the Squirrel should be L22 x 15 x 22 inch. DC24V IP67 LED Driver should be provided seperately. Each animal should be installed on concrete base structure using anchor bolt.

SITC of artistic animal form to be made in translucent polymer of special grade so that uniform glow of the desired colour is achieved from the surface of the polymer. The polymer to be sculpted/formed in the desired artistic shape of illuminated Rabbit shaped sculpture . This should artistically be installed in a form to create glow and aesthetics to these unique elements of nature. These animal forms to be illuminated using special looped LED lights embedded inside the polymer to provide effective and natural looking glow to the animal form. Height of the Rabbit should be L15 x W13 x H22 inch. DC24V IP67 LED Driver should be provided seperately. Each animal should be installed on concrete base structure using anchor bolt.

SITC of artistic animal form to be made in translucent polymer of special grade so that uniform glow of the desired colour is achieved from the surface of the polymer. The polymer to be sculpted/formed in the desired artistic shape of illuminated Peacock shaped sculpture . This should artistically be installed in a form to create glow and aesthetics to these unique elements of nature. These animal forms to be illuminated using special looped LED lights embedded inside the polymer to provide effective and natural looking glow to the animal form. Size of the Peacock should be L55 x W17 x H51 inch. DC24V IP67 LED Driver should be provided seperately for each animal. Each animal should be installed on concrete base structure using anchor bolt.

SITC of artistic a pair of Birds form to be made in translucent polymer of special grade so that uniform glow of the desired colour is achieved from the surface of the polymer. The polymer to be sculpted/formed in the desired artistic shape of illuminated Birds shaped sculpture . This should artistically be installed in a form to create glow and aesthetics to these unique elements of nature. These birds forms to be illuminated using special looped LED lights embedded inside the polymer to provide effective and natural looking glow to the birds form.Size of the Birds should be L7 x W5 x H7 inch & L7 x W2 x H3 inch. DC24V IP67 LED Driver should be provided seperately.

SITC of artistic of bird form to be made in translucent polymer of special grade so that uniform glow of the desired colour is achieved from the surface of the polymer. The polymer to be sculpted/formed in the desired artistic shape of illuminated Parrot shaped sculpture . This should artistically be installed in a form to create glow and aesthetics to these unique elements of nature. These birds forms to be illuminated using special looped LED lights embedded inside the polymer to provide effective and natural looking glow to the birds form. Size of the Parrot should be minimum L18 x W6 x H5 inch. DC24V IP67 LED Driver should be provided seperately.

SITC of artistic bird form to be made in translucent polymer of special grade so that uniform glow of the desired colour is achieved from the surface of the polymer. The polymer to be sculpted/formed in the desired artistic shape of illuminated Crane shaped sculpture . This should artistically be installed in a form to create glow and aesthetics to these unique elements of nature. The sculpture should be illuminated using special looped LED lights embedded inside the polymer to provide effective and natural looking glow to the bird form. Size of the Crane should be L20 x W11 x H27 inch, L23 x W7 x H31 inch, L18 x W14 x H36 inch (wings crane) . DC24V IP67 LED Driver should be provided seperately. Each bird sculpture should be installed on concrete base structure using anchor bolt.

SITC of artistic bird form to be made in translucent polymer of special grade so that uniform glow of the desired colour is achieved from the surface of the polymer. The polymer to be sculpted/formed in the desired artistic shape of illuminated Flamingo shaped sculpture . This should artistically be installed in a form to create glow and aesthetics to these unique elements of nature. The sculpture should be illuminated using special looped LED lights embedded inside the polymer to provide effective and natural looking glow to the bird form. Size of the Flamingo should be L27 x W11 x H48 inch and L27 x W11 x H32 inch. DC24V IP67 LED Driver should be provided seperately. Each bird sculpture should be installed on concrete base structure using anchor bolt.

SITC of artistic Insects form to be made in Acrylonitrile butadiene styrene of special grade so that uniform glow of the desired colour is achieved from the surface of the polymer. The polymer to be sculpted/formed in the desired Animatronic Butterfly shaped public lighting fixture . This should artistically be installed in a form to create glow and aesthetics to these unique elements of nature. These forms to be illuminated using special looped LED lights embedded inside the polymer to provide effective and natural looking glow to the Insects form. Size of the animatronic Butterfly should be L24 x W16 inch. DC12/24V IP67 LED Driver should be provided seperately.

M/S NANU ENGINEERS PVT LTD (BID ID -44187)