COMPREHENSIVE MAINT CENTRAL AC PLANT AIR HANDLING UNIT TOWER AND CONNECTED MISC E AND M WORKAT CGDA COMPLEX UNDER GE EAST DELHI CANTT

Amount

Comprehensive/ routine maintenance of Two Nos Chiller unit through OEM ,Chiller Model:- 30HXC190A Make:- CARRIER , Ser No HJ1118 & HJ1116 AC plant for per months after satisfactory completion of overhauling work through OEM complete all as specified and directed by Engg -in-charge

Comprehensive/ routine maintenance of One Nos Chiller unit through OEM ,Chiller Model:- LCW1-210V082525 Make:- Blue Star , Ser No VF08 AR1220281M3 AC plant for per months after satisfactory completion of overhauling work through OEM complete all as specified and directed by Engg -in-charge

Note :- (i) Water and Electric required for operation of plant shall be provided free of cost by the Department. (ii) After handing over of plant to contractor . Contractor shall fully responsible for satifactory performnace of plant paramenters during complete duration of contract period. During Comprehensive maintance period any type of fault ( Major & Minor ) occurs in chiller plant contractor shall attending and rectify it without cost . No payment is admissible in this account to contractor. (iii) Contractor shall procure and provide all day to day consumable items such as refrigent gas and grease, sensors, electrical and electronic cards, control and power wirings, lugs sundry items etc reqired for operation of chiller AC plant shall be provided by contractor at his own cost . The quoated rate also include the periodical descleaning of condenser coil , chemical cleanaing of cooling tower fins and filters as per OEM recommendations and direction of GE during the period of defect liablity . The cost of the same shall be deemed included in the unit rates quoted by the contractor.

(iv) Contractor should produce MoU of agreement between OEM (carrier) and Blue Star contractor firm from Whom contractor should carry out the comprehensive maintenance of compressor for 11 months time after completion of overhauling work. After due varification from OEM chiller plant shall be handed over to contractor for comprehensive maintenace for 11 months. (v) In case contractor fails to attend fault in 24 hr after intimation by department , he shall be liable to bear the recovery @ Rs 1500 /- per Hr and department shall rectify the fault through other agency on contractor risk and cost and amount should be recovered from contractor dues. (vi) Tradesman will take all preventive measures as per code of practice of EI Rules and the Department will not be responsible for any type of untowards incident.

(vii) To this effect, the tenderer shall submit MoU on Non-Judicial stamp paper of Rs 100/- with any OEM carrier and Blue Star. The installation & testing shall be carried out in the presence of rep of OEM and contractor has to submit test report duly signed by the rep of OEM & Engr-in-Charge. (viii) The contractor has to upload a consent letter on MoU from any OEM i.e Carrier and Blue Star for the same failing which financial bid will not be opened. (ix) Contractors shall provide all kind hand tools / tester as test lamp without any extra cost as per OEM recommendations.

M&L for taking out Condenser Motor Motor 25HP Capacity 720 rpm 3 phase 415 volt opening the motor, cutting & removing old and burnt winding wire, rewinding the motor With new super enameled copper winding of suitable size including,bearing insulating materials, varnishing, drying, replacement of both driven end.non driven end bearings and base plate, reassembling, refixing in same position & connecting including testing and commissioning complete all as specified & directed by engineer in charge Note: The quoated rates must incl. loading & unloading with to and fro transportation for workshop and vice versa

M&L for taking out Chiller Plant Primary & Secondry Motor 20 HP Capacity 720 rpm 3 phase 415 volt opening the motor, cutting & removing old and burnt winding wire, rewinding the motor With new super enameled copper winding of suitable size including,bearing insulating materials, varnishing, drying, replacement of both driven end.non driven end bearings and base plate, reassembling, refixing in same position & connecting including testing and commissioning complete all as specified & directed by engineer in charge Note: The quoated rates must incl. loading & unloading with to and fro transportation for workshop and vice versa

Material and Labour for dismantling of existing Air Handling Unit of any capacity , cleaning, servicing, overhauling to all component of AHU, with and including cleaning of heating & cooling coil with caustic soda solution, including welding / brazing, wherever required to arrest leakages, cleaning of Pre-Micro Filters, replacing of vertical GI sheet supports, complete replacement of foam insulation of best quality using adhesive substance to avoid cold air leakages, fabrication of bottom GI tray of existing size with drain pane made out of 16 guage thick GI Sheets duly painted with bituminous paint over interior surface of tray, re-assembling all the dismantled components to its original position using new nut, bolt, washer and other packing material etc, with and including testing, commissioning of Air handling Unit at optimum efficiency, complete all as directed.

Supply and fix in replacement of industrial type mercury thermometer complete all as specified and directed.

M & L in replacment of unserviceable 2/3 way modulating motorized valve including actuator, Thermostate, LED Display with tempreture display,GI globe body, Brass seating,SS-304 spindle ,Telflon gland,with linear movement actuator 24 V AC input supply,0-10Vinput signal with modulating thermostate & transformer of size-40 mm Make:-SIEMENS/ RAPID CONTROL/RAPID COOL

All as per item No.07 but size 50mm.

M&L for taking out Cooling Tower Motor 10HP Capacity 720 rpm 3 phase 415 volt opening the motor, cutting & removing old and burnt winding wire, rewinding the motor With new super enameled copper winding of suitable size including,bearing insulating materials, varnishing, drying, replacement of both driven end.non driven end bearings and base plate, reassembling, refixing in same position & connecting including testing and commissioning complete all as specified & directed by engineer in charge Note: The quoated rates must incl. loading & unloading with to and from transportation for workshop and vice versa

M&L dismantalling AHU induction motor from AHU base plate inside and arranging the necessory adjusting from fan belt, and then repairing /servicing AHU Fan Motor, following below capacity, opening the motor, cutting & removing old and burnt winding wire, rewinding the motor with new super enameled copper winding of suitable size including insulating materials, varnishing, drying, replacement of both driven end non driven end bearings and base plate, reassembling, refixing in same position & connecting including testing and commissioning complete all as specified & directed Note: The quoated rates must incl. loading & unloading with to and for transportation for workshop and vice versa

15 HP AHU fan motor, 1450 RPM, HX+160MLE4 Make-ABB

12.5 HP AHU fan motor, 1455 RPM, HX+160MLB4 Make-ABB

20 HP AHU fan motor, 1450 RPM, HX+160MLE4 Make-ABB

10 HP AHU fan motor, 1450 RPM, HX+132MLE4 Make-ABB

7.5 HP AHU fan motor, 1454 RPM, HX+132MLE4 Make-ABB

Material & Labour for rewinding of electric motor 1.5 /2 HP, 415 volts, three phase, using Super enameled copper winding wire of gauges equal to or more than existing including replacement of sheet 'E' class insulation and sleeve Including the following jobs (a) Reassembling the motor & refixing (b) Cleaning washing ball bearing with kerosene Oil, greasing with new grease of make Castrol Refixing to its original position testing and Commission complete all as specified and Directed by Engineer-in-charge

Material & Labour for rewinding of electric motor 1.5 HP, 240/230 volts, single phase, using Super enameled copper winding wire of gauges equal to or more than existing. Including Replacement of sheet 'E' class insulation and sleeve Including the following jobs: (a) Reassembling the motor & refixing (b) Cleaning washing ball bearing with kerosene Oil, greasing with new grease of make Castrol Refixing to its original position testing and Commission complete all as specified and Directed by Engineer-in-charge

S&F Float valve assembly of any size as required in cooling tower complete all as specified and directed

Supply only PVC spray assembly / Nozzels of any size in cooling tower as required complete all as specified and directed.

S&F fan blade assembly of cooling tower of cooling tower 225TR capacity as per existing assembly including dismantling old unserviceable blades complete all as specified and directed.

S&F PVC Fills complete all as specified and directed.

Repair & Replacement of Spray Header for 200/225TR Cooling tower complete all as specified and directed.

Supply & fixing in replacement MCCB 415 Volts 50 Hz, Three Pole, 100 Amps capacity 25 kA with thermal release range upto 100 Amps. Make L&T/ Legrand.

Supply & fixing in replacement MCCB 415 Volts 50 Hz, Three Pole, 160 Amps capacity 25 KA, with thermal release range upto 160 Amps. Make L&T / Legrand.

Supply & fixing in replacement Start/ stop Button for Starter Pannels as required at site. Make: L&T or equivalent

Supply & fixing in replacement thermal overload relays type MN directly operated & direct mounting on MNX, of relay range 9-15A. Model MN2. Make L&T or equivalent in Legrant

Supply & fixing in replacement thermal overload relays type MN directly operated & direct mounting on MNX, of relay range 14-23A. Model MN2. Make: L&T or equivalent in Legrant

Supply & fixing in replacement thermal overload relays type MN directly operated & direct mounting on MNX, of relay range 20-33A. Model MN2. Make : L&T or equivalent in Legrant

Supply & fixing in replacement Power Contactor type MNX of size Fr1, suitable for existing starter pannel. Model MNX 12. Make: L&T or equivalent.

Supply & fixing in replacement Power Contactor type MNX of size Fr1, suitable for existing starter pannel. Model MNX 25. Make : L&T or equivalent

Supply & fixing in replacement Power Contactor type MNX of size Fr1, suitable for existing starter pannel. Model MNX 32. Make : L&T or equivalent

Supply & fixing in replacement Power Contactor type MNX of size Fr1, suitable for existing starte pannel. Model MNX 18. Make : L&T or equivalent

Supply & fixing in replacement Power Contactor type MNX of size Fr1, suitable for existing starter pannel. Model MNX 40. Make : L&T or equivalent

Comprehensive maintenance and repair 750 KVA DG Set with AMF of CGDA including replacement of defective parts/fitting inclunding all required electrical and mechanical major / minor spare parts all service required for comprehensive maintenance during the entire contract period of utility press. Make Cummins

Comprehensive maintenance and repair 250 KVA DG Set with AMF of CGDA including replacement of defective parts/fitting inclunding all required electrical and mechanical major / minor spare parts all service required for comprehensive maintenance during the entire contract period of utility press. Make Cummins

Comprehensive maintenance and repair 160 KVA DG Set with AMF of fire fighting including replacement of defective parts/fitting inclunding all required electrical and mechanical major / minor spare parts all service required for comprehensive maintenance during the entire contract period of utility press. Make Kirlosker

Note Item no 34 to 36 (6 Plan + 4 Nos Breakdown visit If require. In a Calendar year and covered panel side, contactor, relay, battery charger, under voltage relay, over voltage relay, and engine side fuel filter, oil filter, air filter-1set , self starter, hose pipe set, clip, controller etc. for each DG sets including service charges for 11 month each DG set. Contractor should producre MoU of agreenebt between Authorised dealer. (i) To this effect, the tenderer shall submit MoU on Non-Jucial stamp paper of Rs 100/- with any OEM (Cotton Greaves/Kirlosker/Cummins) or Authorised service dealer of OEM such as dealers Name Airmen Engineers & Services Pvt Ltd (Rohini Delhi/SSM Diesel) (Kanakpur Delhi/Ambika Power Point) (Ghaziabad, UP) for failing which financial bid will not be opened. (ii) The installation & testing shall be carried out in the presence of rep of OEM and contractor has to submit test report duly signed by the rep of OEM & Engr-in-Charge.

Repair, preventive and periodical maintenance, testing and commissioning of DG Set 320 KVA Make : Mahindra installed at CENTRAD including servicing and replacement of unserviceable parts etc complete all as specified and as directed. Notes: (i) Spare parts shall be measured and paid separately as "Supply only" under respective item of this Schedule. (ii) Coolant and Lub oil shall be measured and paid separately under relevant item of this schedule.

Supply only in replacement following Spare parts of DG Set 320 KVA Make : Mahindra installed at CENTRAD complete all as specified and as directed:-

Flt Element with O ring

Flt INSRT with O Ring

L.O Filter, Element V8/V6

Element Air Filter

S&F in replacement fuse base suitable for cylindrical/DIN type HRC/HBC fuse link type 630/400 A for AMF panel for 750 KVA DG Set complete all as as specified and as directed. Make : L&T Cat Part No SF94437 or Equivalent Model of Seimens/Schinder

S&F in replacement fuse base suitable for cylindrical/DIN type HRC/HBC fuse link type 630/400 A for AMF panel for 160/250 KVA DG Set complete all as as specified and as directed. Make : L&T Cat Part No SF94435 or Equivalent Model of Seimens/Schinder

S&F in repalcement power contactor series CK- 3 pole, AC control 630 A, suitable for AMF panel of 750 KVA DG Set complete all as as specified and as directed. Make : L&T Cat Part No CS96327 or Equivalent Model of Seimens/Schinder

S&F in repalcement power contactor series CK- 3 pole, AC control 250 A, suitable for AMF panel of 250 KVA DG Set complete all as as specified and as directed. Make : L&T Cat Part No CS94141 or Equivalent Model of Seimens/Schinder

S&F in repair single Phase Preventor as per sample complete all as specified & directed. Make : Minilec Model No VSP-2 or Equivalent Model of L&T/Seimens

S&F in repair Engine Starting Relay as per sample at site complete all as specified & directed. Make Minilec/L&T/Seimens

S&F in repair On-Delay timer of 230 VAC, Range: 0 to 30 sec complete all as specified & directed. Make:L&T Cat No ST803280000 or Equivalent Model of BCH/Seimens/Legrand

S&F in repair Under Voltage relay 240/415 Volt as per sample at site complete all as specified & directed. Make: L&T Cat No Equivalent Model of BCH/Seimens/Legrand

Supply, laying & connecting in repair single core, copper conductor, PVC insulated, unsheathed, 1100 V grade (FRLS), 56/0.30, flexible, 4 Sqmm complete all as specified & directed.

Supply, laying & connecting in repair single core, copper conductor, PVC insulated, unsheathed, 1100 V grade (FRLS), 84/0.30, flexible, 6 Sqmm complete all as specified & directed.

Supply and Topping up inhibitor corrosion (Coolant), green/red, suitable for DG Sets 160 KVA to 750 KVA capacity complete all as specified & directed. Make: Servo/IOC/HP/Castrol/BP

Supply and Topping up Lubricant oil 20W/40, multigrade, suitable for DG Sets 160 KVA to 750 KVA capacity complete all as specified & directed. Make: Servo/IOC/HP/Castrol/BP

M&L for Maintenance & repairing of 1.1 KV, LT ACB panel including dusting, oiling, setting of over current and earth fault relay, if required, laid and servicing like all mechanical function including replacement of no volt coil tripping device complete all as specified and as directed.

M&L for repair to transformer 1000 KVA, 11 KV at CGDA to arrest oil leakage comprising of following operations complete all as specified and as directed: - (a) Disconnecting of transformer main supply input & output. (b) Opening up, top, cover, taking out transformer oil. (b) S&F in repair Porcelien LT 1.1 KV Brass rod & gasket (brass rod 40mm) - 04 Nos (c) S&F in repair Porcelien HT 11 KV Brass rod & gasket (brass rod 16mm) - 03 Nos (d) S&F in repair Silica Gel and Breather - 01 Nos (e) S&F in repair rubber cork sheet 3'x2'x6'mm - 01 No Note:- Transformer oil shall be measured and paid separately under respective item of this Schedule.

M&L in repair Thermostate for Oil Temperature for 1000 KVA Transformer complete all as specified and as directed.

M&L in repair Thermostate for Weinding Temperature for 1000 KVA Transformer complete all as specified and as directed.

M&L in repair HT Bushing with insulator for 1000 KVA Transformer complete all as specified and as directed.

M&L in repair LT Bushing with insulator for 1000 KVA Transformer complete all as specified and as directed.

M&L in repair Insulation material for 1000 KVA Transformer complete all as specified and as directed.

Labour for Removing oil leakage from terminal input/output, conservator top cover oil indicator, tab changer, bachhlotz relay (gasket Sheet) packing for 1000 KVA Transformer complete all as specified and as directed.

M&L for Repair to transformer 500 KVA 11 KV at CENTRAD to arrest oil leakage. (a) Disconnecting of transformer main supply input & output comprising of following operations complete all as specified and as directed: - (a) Opening up, top, cover, taking out transformer oil. (b) S&F in repair Porcelien LT 1.1 KV Brass rod & gasket (brass rod 40mm) - 04 Nos (c) S&F in repair Porcelien HT 11 KV Brass rod & gasket (brass rod 16mm) - 03 Nos (d) S&F in repair Silica Gel and Breather - 01 Nos. (e) S&F in repair Rubber cork sheet 3'x2'x6'mm - 01 Nos Note:- Transformer oil shall be measured and paid separately under respective item of this Schedule.

M&L in repair Thermostate for Oil Temperature for 500 KVA Transformer complete all as specified and as directed.

M&L in repair Thermostate for Weinding Temperature for 500 KVA Transformer complete all as specified and as directed.

M&L in repair HT Bushing with insulator for 500 KVA Transformer complete all as specified and as directed.

M&L in repair LT Bushing with insulator for 500 KVA Transformer complete all as specified and as directed.

M&L in repair Insulation material for 500 KVA Transformer complete all as specified and as directed.

M&L filtration and refilling of Transformer oil & alike for various equipment installed at CGDA and CENTRAD through filtration machine to achieve required di-electric strength 50 kVA complete to entire satisfaction of Engr-in-Charge complete all as specified and as directed. Note:-(a) Quoted rate shall deemed to including testing of oil before filtration and after filtration of transformer, OCB & other equipment.(b) Result before filtration & after filtration of oil (Test Certificate) shall be submitted by the contractor to Engr-in- Charge.

Labour of Cleaning of fuel tank made of MS sheet of Diesel tank of 1000 Litre capacity approx, by draining out fuel in a separate container, taking out all silt/ dirt deposition inside the tank, cleaning it completely by manual labour and necessary T&P and refitting and connecting with fuel pipes with DG sets all as per site requirement complete all as specified and as directed.

All as per Ser item No. 72 here-in- before but for 250 KVA DG Set of 360 Litre capacity complete all as specified and as directed.

S&F in repair battery, SMF, 12 Volt,180AH capacity complete all as specified and as directed. Make Exide Express or equivalent Model of Luminous/Amara Raja/Okaya/Amron/Tata Green

S&F in repair battery charger suitable for 750 KVA DG set with charging capacity 48 Volt DC complete all as specified and as directed. Make:- TEKNIKA/Kirloskar/Exide

S&F in repair battery lead with stranded copper conductor of size 95/70 Sqmm, single core, PVC insulated, flexible, 0.6 M long along with battery terminal for positive and stator terminal duly soldered complete all as specified and as directed.

M&L for topping up of transformer oil for transformers/Voltage stablizer installed at different location CGDA complete all as specified and as directed. Make:- SAVITA/IOC/ POWER/ Servo/HP/Castrol/BP

S & F in repair 100 Amp MCCB 4P, 25 KA, adjustable thermal setting, 0.8-1.0x IN thermal release, including necessary copper cable & flexible PVC conduit for internal connection for distribution complete all as specified and as directed. Make L&T Cat equivalent Model of Make mentioned in PS.

All as per item No. 78.00 here in before but 125 Amp, MCCB, 4P, 35 KA, complete all as specified and as directed. Make L&T Cat No SL 986070000 or equivalent Model of Make mentioned in PS.

All as per item No. 78.00 here in before but 150/160 Amp, MCCB, 4P, 35 KA, complete all as specified and as directed. Make L&T Cat No SL 986080000 or equivalent Model of Make mentioned in PS.

All as per item No. 78.00 here in before but 200 Amp, MCCB, 4P, 35 KA, complete all as specified and as directed.

All as per item No. 78.00 here in before but 400 Amp, MCCB, 4P, 35KA, complete all as specified and as directed. Make L&T Cat No SL 978840000 or equivalent Model of Make mentioned in PS.

All as per item No. 78.00 here in before but 630 Amp, MCCB, 4P, 35 KA, complete all as specified and as directed. Make L&T Cat No SL 9945320000 or equivalent Model of Make mentioned in PS.

S&F in repair fuel pipe set suitable for 750KVA, 160 KVA, 82.5 KVA, DG set 20 KVA & 10 KVA DG set complete all as specified and directed.

Supply, laying and connecting in repair 6 Sqmm, 2 Core XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 Volt grade, LT UG electric cable with stranded aluminium conductor including lugs, glands etc, laid in trenches or fixed on wall or drawn through in GI pipe complete all as specifed and as directed.

Supply, laying and connecting in repair 10 Sqmm, 2 Core XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 Volt grade, LT UG electric cable with stranded aluminium conductor including lugs, glands etc, laid in trenches or fixed on wall or drawn through in GI pipe complete all as specifed and as directed.

Supply, laying and connecting in repair 25 Sqmm, 3.5 Core XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 Volt grade, LT UG electric cable with stranded aluminium conductor including lugs, glands etc, laid in trenches or fixed on wall or drawn through in GI pipe complete all as specifed and as directed.

S&F in repair single phase under voltage relay 20-110V AC/DC CT Secondry 5A complete all as specifed and as directed. Make L&T Cat Part No MV12AA00X00 or equivalent Model of Seimens/Schinder or any other Make mentioned in PS.

S&F in repair 3 Phase over current, earth fault relay 20-110V AC/DC 4 No programmable complete all as specifed and as directed. Make L&T Cat Part No MC31AAXX000 or equivalent Model of Seimens/Schinder or any other Make mentioned in PS.

S&F in repair 3 Phase over current , earth fault relay 20-110V AC/DC CT Secondry 5A complete all as specifed and as directed. Make L&T Cat Part No MRP11A50X00 or equivalent Model of Seimens/Schinder or any other Make mentioned in PS.

S&F in repair EP 26-12, 12 Volts, Acid Lead battery, dimension 175x175x166(mm) 42 AH complete all as specified and as directed. Make Exide Powersafe Plus or equivalent Model of Luminous/Amara Raja/Okaya/Amron/Tata Green

M&L dewatering, cleaning of under Ground reservoir, 35000 Litre capacity, with high pressure jet to remove all mosses, algae and dirt and removal of dirty water alongwith sludge machines/industrial vacuum cleaners and disposal of the same at safe distance including scrubbing of internal surface by steel wire brushing, removing the dirt completely using industrial vacumm cleaner and sterilizing the complete internal surface of the tank by using ISI mark, grade I, bleaching powder and marking the date of cleaning using synthetic enamel paint in white colour over black background in six stages cleaning process, as specified here in after complete all as specified and as directed: - (i) Dewatering the tank with portable submersible pump set with flow rate of 30,000 Litres per Hour. (ii) Removal of left over dirty water and sludge with special sludge removal pump set having capacity up to 1.7 lakh Litres per Hour. (iii) Cleaning of wall, ceiling and floor by high pressure rotary water jet with the help of German equipment which create pressure of 80-120. (iv) Removing of remaining sludge from the floor with the help of industrial vaccum cleaner. (v) Spraying of non toxic biodegraded, eco friendly, anti bacterial agent certified by a Govt approved lab to disinfect the tank from harmful pathdons. The dose utilise shall be as per OECD guide No 432. (vi) Treatment of inside tank be exposing UV radiation to kill the suspended or floating bacterial remaining in the tank.

All as per item No 92.00 here in before but cleaning of under Ground Sump of 20,000 Litres capacity complete all as specified and as directed.

All as per item No 92.00 here in before but cleaning of under Ground Sump of 65000 Litres capacity complete all as specified and as directed.

Supply, installation, testing and commisning in replacement submersible pump set, electric driven, 415 Volt, TP, Head 22-57 mtr, discharge (LPM) 520-125 suitable for 200 mm dia bore well casing pipe complete, 5HP, including 40 mtrs long submersible cable of size 6 SqmmMake Crompton Greaves/Kirloskar/KEI

S & F in repair 50 mm bore, galvanised iron tubing, medium grade with all fittings like sockets, elbows, bends, Tees, unions, short pieces etc. laid in trench, in any length including taking down old water tubing complete all as specified and as directed. Note: Necessary Excavation and earth work shall be measured & paid separately

All as per item No 96.00 here in before but 40mm bore pipe complete all as specified and as directed.

All as per item No 96.00 here in before but 32mm bore pipe complete all as specified and as directed.

All as per item No 96.00 here in before but 25 mm bore pipe complete all as specified and as directed.

All as per item No 96.00 here in before but 20mm bore pipe complete all as specified and as directed.

All as per item No 96.00 here in before but 15mm bore pipe complete all as specified and as directed.

S&F in repair gun metal gate/glob valve heavy duty (ISI marked) with iron wheel head screwed both ends, suitable for 15 mm bore iron pipe including testing complete all as specified & directed.

All as per item No 102.00 here in before but suitable for 20mm bore pipe complete all as specified and as directed.

All as per item No 102.00 here in before but suitable for 25mm bore pipe complete all as specified and as directed.

All as per item No 102.00 here in before but suitable for 32mm bore pipe complete all as specified and as directed.

All as per item No 102.00 here in before but suitable for 40 mm bore pipe complete all as specified and as directed.

All as per item No 102.00 here in before but suitable for 50 mm bore pipe complete all as specified and as directed.

S & F in repair 40 mm bore, galvanised iron tubing, heavy grade, both end thraded and duly welded with heavy duty GI Sockets complete all as specified and as directed.

Lifting & Lowering of existing Submersible pump set, repairing pump set with taking out carefully of 18 Nos. column pipe of 50/80 mm size, each length of 3 mtr with flange joints, repairing/ welding all as required at site to column pipe, including proper fixing and connecting of cable with pump set and column pipe and making connection with existing starter complete all as required at site, as specified and as directed. Note: - Flange type joint with Jointing material like Flange, nut-bolts, gasket sheet etc shall deemed to be included in quoted rate.

Supply, laying & connecting in repair flat, 3 core, copper conductor PVC insulated & PVC sheathed cable 1100 Volts grade, size 10 Sqmm, laid in and including 40 mm dia PVC conduit fixed to wall/ in duct complete all as specified and as directed.

Supply, installation, testing and commisning in replacement non clog single phase dewatering pump, Vertical, Monoblock, submersible pump sets, IP 68 Protection, class F, BI- directional Mechanical Seal, 1.1 HP DN 50mm, upto 480 LPM, with built in thermal overload protection and float switch, free flow impellers, Suitable for pumping surface water, rain water, waste water containing solids, drainage of sumps liable to flood, agricultural pits and canals with the following specifications complete all as specified and as directed: - (i) Cast iron- pump casing, (ii) cast iron - imepeller, (iii) Rotor Shaft- Chrome Steel,

Supply, installation, testing and commisning in replacement Induction pump Motor, Three phase, 415V, 50x40mm, Head -46 Mtr, 3.7KW/5HP, 50 HZ complete all as specified and as directed. Make Kirlosker Cat No KDS 550++ or equivalent model of KSB/CG or any other make mentioned in PS.

Supply, installation, testing and commisning in replacement Centrifugal Monoset Pump, Three phase, 415V, 65x50mm, RPM -2880, Head -46.0 Mtr, 3.7KW/5HP, 50 HZ complete all as specified and as directed. Make CG Cat No MBHH5Z or equivalent model of KSB/Kilosker or any other make mentioned in PS.

Supply, installation, testing and commisning in repair submersible pump set, electric driven, 415 Volt, TP, Head- 216 (mtr) Discharge 0-100 LPM suitable for 150/200 mm dia bore well, casing pipe complete up to 3 WHp including 40 Mtrs long submersible cable of size 6 Sqmm, three core replacement complete all as specified and as directed.

Supply, installation, testing and commisning in replacement submersible pump set, electric driven, 36 Uf, 440 Volt, 2780 RPM, Suitable for 40 mm Dia pipe, Head Max 12Mtr, Maximum Discharge 12000 LPH, Max Solid Size 38mm, up to 1.5 WHP, including 10 mtrs long submersible cable of size 2.5 Sqmm, three core complete all as specified and as directed.

Supply and fix in replacement LED decorative post of lantern 35 Watt fittings including all accessories completefixing accessories and clamp including 4 metre height black painted glavanized pole, fixed in position including necessary PCC work and execavation as per manufactuer's instruction all as specified and directed by Engg -in-charge. Make:- For fitting CG , cat part No:- LPTOI-45- CDL/T or equivalent in Philips, GE, Havell's

Supply and lay in replacement of Pipe PVC( UPVC) class “A” conforming to IS 13592 including special, OD 75mm dia.

Supply and lay in replacement of Pipe PVC( UPVC) class “A” conforming to IS 13592 including special, OD 65 mm dia.

Supply and lay in replacement of Pipe PVC( UPVC) class “A” conforming to IS 13592 including special, OD 50 mm dia.

Supply and fixing in replacement of PVC valves class “A” for UPVC pipe of OD 50 mm dia.

Supply and fixing in replacement of PVC valves class “A” for UPVC pipe of OD 65 mm dia.

Supply and fixing in replacement of PVC valves class “A” for UPVC pipe of OD 75 mm dia.

Excavation in trenches not exc 1.5 m wide and n.exc 1.5 m in depth for foundation / fixing pole / laying cable and pipe line etc or for man hole etc not exc 10 sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning filling in including spreading, levilling, watering and well ramming in layers, not exeecding 25 cm thick using excavated soil complete all as specified and directed.

Removing excavated Soil to a distence not exceeding 50 m and deposting where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M&L for providing dry river sand as in sand cushioning to under ground electric cable including punning down of sand in layercomplete all as specified and directed by Engg-in-Charge. Note: for measurement purpose punned thicness of sand only will be considered.

Supply and Laying burn brick size 225 mm X 113 mm X 75 mm etc complete all as specified and directed.

M&L for taking out Vertical Motor 2.5HP Capacity 3 phase 415 volt opening the motor, cutting & removing old and burnt winding wire, rewinding the motor With new super enameled copper winding of suitable size including,bearing insulating materials, varnishing, drying, replacement of both driven end.non driven end bearings and base plate, reassembling, refixing in same position & connecting including testing and commissioning complete all as specified & directed by engineer in charge Note: The quoated rates must incl. loading & unloading with to and fro transportation for workshop and vice versa

M&L for taking out Vertical Motor 5HP Capacity 3 phase 415 volt opening the motor, cutting & removing old and burnt winding wire, rewinding the motor With new super enameled copper winding of suitable size including,bearing insulating materials, varnishing, drying, replacement of both driven end.non driven end bearings and base plate, reassembling, refixing in same position & connecting including testing and commissioning complete all as specified & directed by engineer in charge Note: The quoated rates must incl. loading & unloading with to and fro transportation for workshop and vice versa

Vishal Traders