GE/PNH-21/2024-25

Amount

Dismantling water tanks of any description and removing from site of capacity exc 250 & n.exc 500 ltrs, complete all as specified and directed.

Dismantling water tanks of any description and removing from site of capacity exc 500 & n.exc 1000 ltrs, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs incl with 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs incl with 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule, complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced) on ground floor or paving not exc 15 cm thickness (below or above ground level), complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 with (using 12.50 mm graded crushed stone aggregates) as in sub base of flooring, finished even and rough to receive the top layers, complete all as specified and directed.

M&L for Non skid ceramic tiles of size 400x400x7mm thick premium quality as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

M&L for Non skid ceramic tiles of size 400x400x7mm thick premium quality as in skirting, dados, steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & incl 10mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for Vitrified coloured tiles 10 mm thick, premium quality (square/rectangular) area of each tile not less than 0.36 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

All as per Item No 10 above but as in skirting/dados including 10mm thick screed bed in CM (1:4), complete all as specified and as directed.

M&L for glazed ceramic coloured/printed digital tiles, Premium quality of size 450x350x7 mm thick fixed as in vertical surfaces such as skirting, dados & repairs to step etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick plaster in CM (1:4), complete all as specified and as directed.

M&L for 300x300mmx25mm thick chequered cement concrete tiles set and jointed in neat cement slurry and pointed in white or coloured cement mixed with mixture of pigments to match with the colour of tiles laid over and including 20mm thick screed bed in CM (1:6), including demolition of existing floor tiles complete all as specified and as directed.

M&L for 40mm cement concrete type B-1, 1:2:4 (20mm graded crushed stone aggregate) as in floor finish finishing cement concrete surface even and smooth without using extra cement ,complete all as specified and as directed.

S&F Glass dividing strip 3mm thick, 38mm width, inserted in position, confirm to design, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc. finished the surface even & fair, complete all as specified and directed.

M&L for 18-20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 20mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and and moulding the edges, complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20-25mm thick , bedded and jointed with grey cement slurry and pointed with grey cement with admixture or pigment to match the shade of Kota stone slab as approved by GE, laid over and including screed bed or bedding layer of mortar 20mm thick in Cement Mortar (1:6) including cutting, grinding and mirror polishing, complete all as specified and directed.

M&L for machine cut pre polished Kota stone 20-25mm thick as in riser of steps, skirting, dado and pillar fixed over & including cement plaster 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the kota stone including cutting, grinding and mirror polishing, complete all as specified and directed.

Dismantling plain/corrugated steel sheeting, any gauge, thickness, complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for roof trusses and purlins, complete all as specified and as directed.

S&F Rolled mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410W(Gde E-250), quality 'A' complete all as specified and directed.

All as per item No 24 above but except mild steel (fixing only old serviceable mild steel obtained from dismantling from item No 22 above), complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, valley gutter, ridge & similar works fixed with self tapping screws complete all as specified and directed.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with 'L' or 'J' type or cranked hook bolts and washers in roofs, wall etc complete all as specified and directed.

S&F Plain, galvanised, 0.80 mm thick mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed), complete all as specified and as directed.

M&L for preparation of steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each, complete all as specified and directed.

Taking down shutters of any description, area exceeding 1 Sqm and not exc 2 Sqm complete all as specified and directed.

S&F solid PVC door frame of size 50 X 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplied and fixed in opening as per specifications and drawing, complete all as specified and as directed.

S&F factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail, MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; Panelling of plain colur PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, Supplied and Fixed in the frame at site as per specification and drawings, complete all as specified and as directed.

S&F mild steel butt hinges, medium weight, cold rolled, 100mm long, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section of size 150mm, complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 150mm, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm and not exceeding 4Sqm each, complete all as specified and directed.

Refixing shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each, complete all as specified and directed.

S&F plain, solid, 2nd class hard wood straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joint etc ,complete all as specified and as directed.

S&F Factory made pressed steel frames of size 105x60mm made out of PBI sheet 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinge,lock strike plate etc.complete including bottom of each chowkhat to be welded with 02 Nos 25x25x3mm thick angle iron projecting 10cm on either side & PCC 1:3:6 type C-0 in back filling of chowkats & tarring back of chowkats and holdfasts complete all as specified and directed.

S&F Factory made pressed steel frames of size 125x60mm made out of PBI sheet 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinge,lock strike plate etc.complete including bottom of each chowkhat to be welded with 02 Nos 25x25x3mm thick angle iron projecting 10cm on either side & PCC 1:3:6 type C-0 in back filling of chowkats & tarring back of chowkats and holdfasts complete all as specified and directed.

M&L for PCC 1:3:6 type C1 using 20m graded crushed stone aggregate as in bed block or for embedding of holdfasts, complete all as specified and as directed.

S&F 35 mm thick Flush shutters, solid core, construction, with particle board core and plywood face panels, commercial type on both sides, complete all as specified and as directed.

S&F 35 mm thick 2nd Class hard wood gauged and skeleton shutters, open rebated and prepared to receive gauge etc (with sash bars), edges of framing plain, chamfered or grounded, fitted with cut of and mitred beads for securing gauge etc of size of members of shutters as specified in SSR Part-I section 8 clause No. 8.2(a) and fitted to chowkats complete all as specified and as directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding of extruded section ,complete all as specified and as directed.

S&F mild steel pressed handle, oval type stove enamelled, black of size 150mm, complete all as specified and directed.

S&F mild steel barrel tower bolt, stove enamelled black, with bright bolt of 75 mm long, complete all as specified and directed.

S&F 2nd class hard wood, 30 mm thick, glazed and skeleton shutter, divided into square, with plain, chamfered or rounded mitered and rebated sash bars, any number of panels, prepared to receive glass, gauge etc. edges of frames chamfered or rounded, fitted with cut and mitered beads for securing glass etc. size of members as specified in SSR Part I clause 8.24 (b) kiln seasoned and chemically pressure treated, complete all as specified and directed.

All as per item No 49 above but without sash bar as in window/ventilators, complete all as specified and as directed.

S&F mild steel butt hinges, medium weight, cold rolled,75mm long, complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 100mm and fixed, complete all as specified and directed.

S&F in repair Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm with tinned tacks or galvanised wire stapple, complete all as specified and as directed.

S&F Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aparture 1.18mm with tinned tacks or galvanised wire stapple, complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and as directed.

S&F 300 mm, mild steel ordinary rat tail, rod pattern springs including roller and roller plate, complete all as specified and as directed.

M&L for two coat of synthetic enamel paint over a coat of pink primer including preparation of new or previously untreated wooden surfaces of any description, over 10cm width or girth, complete all as specified and directed.

S&F in repair PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints, complete all as specified and directed. Make:- Prayag cat part No 501 or equivalent cat part of make as specified in P.S.

S&F in repair 15mm bore pillar tap cast copper alloy with capstan head, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe, complete all as specified and directed.

S&F in repair Bib tap 15 mm bore, Brass CP, fancy type (long shank). with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in repair Stop / Angle cock (ISI Marked), cast copper alloy fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and directed.

S&F in repair Vitreous china urinals, bowl type of size 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with brackets, flush pipe, waste pipe grating and union for discharge pipe, complete all as specified and directed.

S&F in repair Vitreous china wash basin, white flat back, size 550 x 400 mm excl taps, waste chain and plug and porcelain stopper but incl brackets, waste pipe & CP waste coupling ,complete all as specified and as directed.

S&F in repair PVC connection 15 mm bore with CP nuts of length 600 mm long, complete all as specified and as directed.

S&F in repair brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and directed.

S&F in repair Grating doom 75 mm dia with waste hole of PTMT (minimum weight - 25 gms) complete all as specified and directed.

S&F in repair Grating doom 100 mm dia with waste hole of PTMT (minimum weight - 40 gms) complete all as specified and directed.

S&F in repair Vitreous china wash down water closet pan (Pedestal pattern) white (excluding flushing cistern and flush pipe) but including plastic water closet seat, black, closed pattern with flat bottom, fixing bolts and cover and mild steel CP or aluminised hinging device,, complete all as specified and as directed.

S&F in repair vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 'S' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed.

S&F in repair stop valve fancy type cast copper alloy 15 mm dia, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handles, screwed both ends incl necessary fittings such as sockets for iron pipes or for unions, complete all as specified and directed.

Taking up or down GI tubing 15mm bore pipe and connection including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down or 20mm steel tubing and connections incl cleaning for refixing or removal to store complete all as specified and directed.

S&F galvanized steel water tubing of 15 mm bore ‘medium grade’ with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F galvanized steel water tubing of 20 mm bore ‘medium grade’ with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

Taking down cement plaster on wall of any desription incl racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:6 on fair faces of brick work or cocrete surfaces, finished even & smooth without using extra cement, complete all as specified and as directed.

M&L for 15mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm and 5mm thick) mixed with water proofing compound in top layer @3% by the weight of cement or as per manufacturer's instructions finishing the surface even and smooth without using extra cement complete all as specified and as directed. Note : Integral water proofing compund shall be measured and paid separtely.

Supply only integral water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed.

M&L for applying two coats of distemper on walls over newly plastered surfaces of wall incl preparation of surfaces complete all as specified and as directed.

Material & Labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces of walls complete all as specified and as directed.

S&F in repair powder coated aluminium work incl 5.5 mm glass sheet/prelaminated particle board with both sides decorative (minimum thickness of powder coating 50 micron) work foor doors, windows, ventilators and partitions (fixed portions) with extruded built up stamdard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size incl necessary filling up the gaps at junctions with required EPDM rubber/neoprene gasket etc, aluminium sections shall be smooth, rust free, straight metred and jointed mechanically wherever required incl cleat angle, alum snap beading for gazing/panelling , complete all as specified and as directed by Engr-in Charge.

S&F in repair prelaminated particle board, interior grade, prelaminated on one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timberframe work, complete all as specified and directed.

M&L for 18/19 mm thick extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails, fixed in repair complete all as specified and directed.

S&F in repair anodised aluminium frame section of size 100mm x 44mm x 1.8 mm thick made of Square/tubular aluminium section for door with one or more rebates jointing cleat for fixing etc and provision of aluminium door shutter (Single/Double shutter) having section of door shutter 101.06x44.45mm, lock rail 81.50x44.45mm, bottom rail 150X44.45mm, style of size 85x44.45mm top rail 83x44.45mm, and thickness of aluminium member 2mm thick including necessary jointing cleats glazing clips, 5.5mm thick tinted / plain glass, rubber gasket aluminium anodised snap beading, screws, hold fast, aluminium hinges 3Nos 100mm long for each shutter, floor stopper, locking arrangements handle , complete all as specified and directed.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, complete all as specifeid and as directed.

S&F in repair door closer hydraulically regulated, designation No-3 universal type, aluminium (extruded section body), suitable for door shutter of 851 to 1000mm in width and weight between 61 to 80 Kg, complete all as specified and directed.

Dismantling of wall and ceiling boards any thickness including cover cover fillets, complete all as specified and directed.

Dismantling timber in scantling 40 sqcm and over in section unframed work, complete all as specified and directed.

Dismantling of timber scantling under 40sqcm in section unframed work as in fillets, rails, posts, rafters, purlins etc, complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling of size 605 x 605mm with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long 6mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid complete all as specified and as directed.

S&F 6 mm thick plywood, grade BWP, type BB fixed with screws to timber frame work fixed with nails as in ceiling, flat or sloping, complete all as specified and directed.

S&F 5-6 mm thick insulated PVC coloured wall panelling including lining and necessary cleats, screws etc for fixing to wall, complete all as specified and directed.

S&F 2nd class soft wood (Kail) as in scantling, clean sawn and fitted in unframed work, complete all as specified and directed.

All as per srl item No. 94 above but except timber scantling, complete all as specified and directed.

M&L for 2nd class hardwood plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc 13 sqcm & not exc 25 sqcm complete all as specified and directed.

M&L for Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote oil complete all as specified and directed.

M&L for 2nd class hardwood plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc 3 sqcm & not exc 6 sqcm complete all as specified and directed.

M&L for two coat of synthetic enamel paint including preparation of old previously wooden surfaces of any description, over 10cm width or girth, complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

M&L for walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

All as per item No. 101 above, but except stone complete all as specified and directed

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

S&F in repair brass CP toilet paper holder fixed to wall with screws, complete all as specified and directed. Make-Jaquar Cat Part No:-AKB-35751 or Equaivalent cat part of make as specified in P.S.

S&F in repair brass CP soap dish with poly carbonate dish fixed to wall with brass screws, complete all as specified and directed. Make-Jaquar Cat Part No:-AQN-7733 or Equaivalent cat part of make as specified in P.S.

S&F in repair sheet glass shelf 600 mm long with chromium plated bracket guard and railing fixed to wall with brass screws, complete all as specified and directed. Make-Jaquar Cat Part No:-ACN-1171N or Equaivalent cat part of make as specified in P.S.

S&F in repair EWC with super constellation type flushing cistern white including seat cover, complete all as specified and directed. Make-CERA Cat Part No:- 2068/2368/2268 or Equaivalent cat part of make as specified in P.S.

M/S KHAN ENTERPRISES

JAMWAL CONSTRUCTION CO

narayan construction