REPAIR AND MAINTENANCE OF WOODEN AND STEEL FURNITURE AT ICGS AND ICGAS RATNAGIRI

Amount

REPAIRS TO ALMIRAH LARGE/SMALL (FD-67/1031/1032)

S&F of handle steel Chromium plated of size 100mm long with 25mm long steel pin to make 3 way locking system fully operational including removing of unserviceable handle steel from Almirah steel of any size or type complete all as per specified and directed.

S&F of three way locking device to making the system fully operational including removing of unserviceable locking system of Almirah large steel complete all as per specified and directed.

All as per item No. 1.2 here in above but for Almirah steel Small complete all as specified and directed.

S&F of Lock six livers, brass of best pattten, with duplicate keys and including removing unserviceable lock from Almirah steel of any size or type complete all as per specified and directed.

S&F of Clips for fixing of shelves, including removing unserviceable clips from Almirah steel of any size or type complete all as per specified and directed.

Repairs to door as specified including replacement of Hinges of almirah steel small / large all as per specified and directed.

M&L for preparation of old painted surfaces by rubbing down with emery paper without damaging the existing coat, clean throughly to remove all dust/oily sport etc and applying one coat of synthetic emanel paint olive green with spray gun all side for Almirah large steel all as specified and directed.

S&F shelves of MS sheet 1.00 mm thick of existing size and shape including applying a coat of red oxide primer and including removing of unserviceable shelves from Locker bedside steel complete all as specified and directed.

REPAIR TO CHARPOYS WITH HARD TOP (FD- MAP-II/01)

Removing the existing unserviceable Plywood from charpoy and tighting of the frame of charpoys and supply and fixing of 12mm thick ply wood commercial, BWR grade ISI Marked of size 1980mm x 900mm and rounded edges on four corners with nuts 6mm dia 75mm long with washers (3mm thick duly drilled 10 holes per charpoy) (03 each on both long rails and 02 Nos of each on both short rails) and fixing complete including S & F 02 Nos flat iron 40mm width x 5mm thick x 880mm length to be placed over long rails (Flat iron to be placed between plywood and long rails and to be fixed with be same bolt and washers mentioned above). The ends of flat iron should be gound smoothly and apply two coat of enamel paint black over a coat of metal primer for entire flat iron all as specified and directed.

Repairs to Table Steel Office Officers, Table office clerk, FD-1004 and FD-1003

(a) Taking out defaced surface and welding of broken portion and matching the surface by applying synthetic enamel paint of existing of colour and shape including preparation of surfaces as directed by Engineer-in-Charge.

(b) Taking out unserviceable top from table and Supply and Fixing new top made of 18mm thick particle board fixed with nuts and bolts duly fixed with 1mm thick laminated sheet complete all as shown on drawing, specified and directed by Engineer-in-Charge.

Chair CB Steel with Arms and without Arms FD- 75

( a ) Removing / taking out carefully of old existing unserviceable / broken seat of chair CB Steel with Arms of any description, in any position & replacement of the same with new seat duly canning, cane shall be 2mm wide and 0.4mm thick gola type, wooden surfaces of seat shall be painted with high gloss black paint. Wood for seat shall be made first class hard wood (teak wood) complete all as shown on drawing and directed, painting of new existing portion , by Engineer - in - Charge.

b) Removing / taking out carefully of old existing unserviceable / broken back of chair CB Steel with Arms of any description, in any position & replacement of the same with new back duly canning, cane shall be 2mm wide and 0.4mm thick gola type, wooden surfaces of seat shall be painted with high gloss black paint. Wood for seat shall be made first class hard wood (teak wood) complete all as shown on drawing and directed by Engineer - in - Charge.

c) Removing / taking out carefully of old existing unserviceable / broken seat of chair CB Steel with out Arms of any description, in any position & replacement of the same with new seat duly canning, cane shall be 2mm wide and 0.4mm thick gola type, wooden surfaces of seat shall be painted with high gloss black paint. Wood for seat shall be made first class hard wood (teak wood) complete all as shown on drawing and directed by Engineer - in - Charge.

d) Removing / taking out carefully of old existing unserviceable / broken back of chair CB Steel with out Arms of any description, in any position & replacement of the same with new back duly canning, cane shall be 2mm wide and 0.4mm thick gola type, wooden surfaces of seat shall be painted with high gloss black paint. Wood for seat shall be made first class hard wood (teak wood) complete all as shown on drawing and directed by Engineer - in - Charge.

(e) All as per item No 4.1(a) above but replacement of Arm rest with Supply and Fixing new arm rest made out of Ist class hard wood (teack wood) wooden surfaces of Arm Rest shall be painted with high gloss black paint.complete all as shown on drawing and directed Engineer-in-Charge

Rack steel adjustable type HFD-2032 Rack steel of 6 tier (adjustable type).M&L for painting to Almirah large with shelves and Almirah large glazed w/shelves by de-rusting of surfaces with fine sand paper and leveling to ciped out old painted surfaces with steel putty as per standard workmanship and applying one coat of synthetic enamel paint OG colour on the dry steel surfaces etc complete all as specified and directed.

REPAIR TO CHAIR VARANDAH (FD - 359) Taking out old worn out cane from chair varandah and welding the broken joints and applying two coats of paint synthetic enamel white by hand brush over a well prepared surface and recaning the same with 4 mm wide 0.6mm thick half round white plastic cane complete as specified and directed.

REPAIRS TO LOCKER STEEL (Drg No - WDF/002)

S&F of handle steel chromium plated of size 100mm long with 25mm long steel pin to make 3 way locking system fully operational including removing of unserviceable handle steel from locker steel of any size or type complete all as per specified and directed.

Repairs to door as specified including replacement of Hinges of Locker steel all as per specified and directed.

M&L for preparation of old painted surfaces by rubbing down with emery paper without damaging the existing coat, clean throughly to remove all dust/oily sport etc and applying one coat of synthetic emanel paint olive green with spray gun all side for Locker steel all as specified and directed.

S&F shelves of MS sheet 1.00 mm thick of existing size and shape including applying a coat of red oxide primer and including removing of unserviceable shelves from Locker bedside steel all as specified and directed.

SIDE RACK WITH TRAY (FD-1023) M&L for painting to side rack with tray with shelves by de-rusting of surfaces with fine sand paper and leveling to ciped out old painted surfaces with steel putty as per standard workmanship and applying one coat of synthetic enamel paint OG colour on the dry steel surfaces etc complete as specified and directed by Engineer - in - Charge.

OFFICE TABLE 4'6" X 2'6" (TP)

(a) Taking out defaced surface and welding of broken portion and matching the surface by applying synthetic enamal paint of existing of colour and shape including preparation of surfaces and directed by Engineer -in-Charge.

(b) Taking out unserviceable top from table and Supply and Fixing new top made of 18mm thick particle board fixed with nuts and bolts duly fixed with 1mm thick laminated sheet complete all as shown on drawing, specified and directed by Engineer-in-Charge

COMPUTER TABLE 4' X 2' (TP)

(a) Taking out defaced surface and welding of broken portion and matching the surface by applying synthetic enamel paint of existing of colour and shape including preparation of surfaces as directed by Engineer-in Charge.

(b) Taking out unserviceable top from table and Supply and Fixing new top made of 18mm thick particle board fixed with nuts and bolts duly fixed with 1mm thick laminated sheet complete all as shown on drawing, specified and directed by Engineer-in-Charg

(c) Taking out unserviceable Keyboard trolly and channel from table and Supply and Fixing new Keyboard trolly and channel made of 18mm thick particle board fixed with nuts and bolts duly fixed with 1mm thick laminated sheet complete all as shown on drawing, specified and directed by Engineer-in-Charg

EXECUTIVE COMPUTER TABLE 915MM X 610MM X 685MM (TP)

(a) Taking out defaced surface and welding of broken portion and matching the surface by applying synthetic enamel paint of existing of colour and shape including preparation of surfaces as directed by Engineer-in-Charge.

(b) Taking out unserviceable top from table and Supply and Fixing new top made of 18mm thick three leyer perlamiratied particle board fixed with nuts and bolts duly fixed with 1mm thick laminated sheet complete all as shown on drawing, specified and directed by Engineer-in-Charg

REPAIR TO BED HARD WITH MNF SET (FD/E6/MAP-II/08 (R) Removing the existing unserviceable Plywood from charpoy and tighting of the frame of charpoys and supply and fixing of 12mm thick ply wood commercial, BWR grade ISI Marked of size 1980mm x 900mm and rounded edges on four corners with nuts 6mm dia 75mm long with washers (3mm thick duly drilled 10 holes per charpoy) (03 each on both long rails and 02 Nos of each on both short rails) and fixing complete including S & F 02 Nos flat iron 40mm width x 5mm thick x 880mm length to be placed over long rails (Flat iron to be placed between plywood and long rails and to be fixed with be same bolt and washers mentioned above). The ends of flat iron should be gound smoothly and apply two coat of enamel paint black over a coat of metal primer for entire flat iron all as specified and directed.

OFFICE TABLE STEEL WITH DRAWERS (900mm x 600mm x 760mm (FD- 1008)

(a) Taking out defaced surface and welding of broken portion and matching the surface by applying synthtic enamel paint of existing of colour and shape including preparation of surfaces as directed by Engineer-in-Charge.

(b) Taking out unserviceable top from table and Supply and Fixing new top made of 18mm thick particle board fixed with nuts and bolts duly fixed with 1mm thick laminated sheet complete all as shown on drawing, specified and directed by Engineer-in-Charg

(c) Taking out unserviceable Keyboard trolly and channel from table and Supply and Fixing new Keyboard trolly and channel made MS sheet 1.00 mm thick of existing size complete all as specified and directed.

(d) All as per item No. 32 here-in-before but replacement of drawer including brass knob of suitable size and dia with supply and fixing new drawer made out of MS sheet 1.00mm thick of existing size with brass knob chromium plated 40mm dia as approved by GE (I) (CG) Ratnagiri, complete all as shown on drawing specified and directed.

CHAIR HEAVY DUTY WITH CUSHON (TP)

(a) Removing of old unserviceable tapestry cloth from cushion and providing new tapestry cloth approved Superior quality as approved by Engr-in-charge.

(b) Removing of old unserviceable cushion and tapestry cloth and providing new 50mm thick cushion of approved superior quality (sleep well) of 32 density covered with best quality tapestry cloth as approved by Engr-in-Charge.

REPAIR TO CHAIR DINING/CBB (FD - 279)

Removing taking out carefully existing unserviceable broken back leg of the chair dining / CBB of any description in any position & replacement of the same with new back leg of Ist class hard wood (trak wood) made to shape, fixed in position all as shown on drawing spefcified and directed.

All as per item No.15.1 here-in-before but for front leg complete all as specified and directed.

All as per item No. 15.1 here-in-before but replacement of side rail with Supply and Fixing new side rail made out of Ist class hard wood (teak wood) with holes for weaving. The spacing of holes shall match with the existing rail on other side complete all as specified and directed.

All as per item No. 15.1 here-in-before but replacement of front and back rail with Supply and Fixing new front or back rail made out of Ist class hard wood (teak wood) with holes for weaving. (The spacing of holes shall match with the existing rail on other side) complete all as specified and directed.

All as per item No 15.1 above but replacement of stiffener with Supply and Fixing new stiffener made out of Ist class hard wood (teack wood) complete all as shown on drawings and directed.

All as per item No. 15.1 here-in-before but replacement of back strip with Supply and Fixing new back strip made out of Ist class hard wood (teack wood) complete all as shown on drawing and directed.

All as per item No. 15.1 here-in-before but replacement of rubber ring with Supply and Fixing new hard rubber ring under the leg, superior quality with steel screw of size 20mm long complete all as shown on drawings and directed.

REPAIRS TO CHAIR WRITING/CBA ( FD - 280)

Removing/taking out carefuly of old existing unserviceable/broken back leg of chair writing/CBA of any description, in any position & replacement of the same with new back leg made of Ist class hard wood (teak wood) made to shape, fixed in position all as shown on drawing, polishing of new existing portion, specified and directed.

All as per item No. 16.1 here-in-before but for front leg complete all as specified and directed.

All as per item No. 16.1 here-in-before but for replacement of side rail with Supply and Fixing new side rail made out of Ist class hard wood (teack wood) with holes for weaving. The spacing of holes shall match with the existing rail on other side complete all as specified and directed.

All as per item No. 16.1 here-in-before but replacement of front and back rail complete all as specified and directed.

All as per item No. 16.1 here-in-before but replacement of back strip with Supply and Fixing new back strip made out of Ist class hard wood (teack wood) complete all as shown on drawing and directed.

All as per item No. 16.1 here-in-before but replacement of Arm rest with Supply and Fixing new arm rest made out of Ist class hard wood (teack wood) complete all as shown on drawing and directed.

All as per item No. 16.1 here-in-before but replacement of stiffener with Supply and Fixing new stiffener made out of Ist class hard wood (teak wood) complete all as shown on drawings and directed.

All as per item No.16.1 here-in-before but replacement of rubber ring with Supply and Fixing new hard rubber ring of superior qualaity under the leg with steel screws of size 20mm long complete as shown on drawiwng and directed.

REPAIRS TO CHAIR EASY (FD - 229)

Removing/taking out carefuly of old existing unserviceable/broken back leg of chair Easy of any description, in any position & replacement of the same with new back leg made of Ist class hard wood (teak wood) made to shape, fixed in position all as shown on drawing, polishing of new existing portion, specified and directed.

All as per item No. 17.1 here-in-before but for front leg complete all as specified and directed.

All as per item No.17.1 here-in-before but for replacement of seat side rail with Supply and Fixing new side rail made out of Ist class hard wood (teack wood) with holes for weaving. The spacing of holes shall match with the existing rail on other side complete all as specified and directed.

All as per item No. 17.1 here-in-before but replacement of seat front and back rail complete all as specified and directed.

All as per item No. 17.1 here-in-before but for replacement of back side rail with Supply and Fixing new back side rail made out of Ist class hard wood (teack wood) with holes for weaving. The spacing of holes shall match with the existing rail on other side complete all as specified and directed.

All as per item No. 17.1 here-in-before but replacement of back top and bottom rail complete all as specified and directed.

All as per item No. 17.1 here-in-before but replacement of Arm rest with Supply and Fixing new arm rest made out of Ist class hard wood (teack wood) complete all as shown on drawing and directed.

All as per item No. 17.1 here-in-before but replacement of stiffener with Supply and Fixing new stiffener made out of Ist class hard wood (teak wood) complete all as shown on drawings and directed.

All as per item No. 17.1 here-in-before but replacement of rubber ring with Supply and Fixing new hard rubber ring of superior qualaity under the leg with steel screws of size 20mm long complete as shown on drawiwng and directed.

REPAIRS TO CHAIR WOODEN BOTTOM (FD - 285)

Removing, taking out carefully old existing unserviceable plywood of seat for chair woooden bottom without arms and replacement of the same with Supply and Fixing new plywood both side commercial face BWR grade confirming to IS-373, 8mm thick for seat with holes made in to shape fixed with 24 Nos steel screws of suitable size in position all as shown on drawing, specified and directed.

All as per item No. 18.1 here-in-before but replacement of back leg with Supply and Fixing new back leg made out of Ist class hard wood (teak wood) complete all as shown on drawing.

All as per item No. 18.1 here-in-before but replacement of front leg with Supply and Fixing new front leg made out of Ist class hard wood (teak wood) complete all as shown on drawings.

All as per item No. 18.1 here-in-before but replacement of side rail with Supply and Fixing new side rail made out of Ist class hard wood (teak wood) complete all as shown on drawings, specified and directed.

All as per item No. 18.1 here-in-before but replacement of front/back rail with Supply and Fixing new front/back rail madeout of Ist class hard wood (teak wood) complete all as shown on drawings, specified and directed.

All as per item No. 18.1 here-in-before but replacement of wooden back strip with Supply and Fixing new wooden back strip make out of Ist class hard wood (teak wood) complete all as shown on drawings, specified and directed.

All as per item No. 18.1 here-in-before but replacement of stiffener with Supply and Fixing new stiffener made out of Ist class hard wood (teak wood) complete all as shown on drawing, specified and directed.

All as per item No. 18.1 here-in-before but replacement of rubber shoe including screws with supply and fixing new hard rubber shoes of superior quality fixed with steel screws of suitable size to the bottom of leg complete as shown on drwings and directed.

Supply and Fixing new bracket with 04 Nos steel screws suitable size made out of Ist class hard wood (teak wood) of size 75mm x 75mm x 25mm fixed with 04 Nos steel screws complete all as shown on drawings and directed.

REPAIR TO TABLE WOODEN 900MM X 600MM WITH DRAWER/WITHOUT DRAWER (FD - 283/284)

Removing/taking out carefully of old existing unserviceable/broken/damaged table top of table 900mm x 600mm of any description in any position and replacement of the same with Supply and Fixing new table top of 18mm thick pre-laminated particle board BWR exterior grade with and including 6 mm thick teak wood beading around, the top, made to shape fixed in position all as shown on drawing, specified, polishing of new existing portion and directed.

All as per item No. 19.1 here-in-before but replacement of leg with Supply and Fixing new leg made out of Ist class hard wood (teak wood) complete all as shown on drawing specified and directed.

All as per item No. 19.1 here-in-before but replacement of long rail of table frame with Supply and Fixing new long rail make out of Ist class wood (teak wood) complete all as shown on drawing specified and directed.

All as per item No. 19.1 here-in-before but replacement, short rail of table frame with Supply and Fixing new table frame short rail made out of Ist class hard wood (teak wood) complete all as shown on drawings specified and directed.

All as per item No. 19.1 here-in-before but replacement of drawer including brass knob of suitable size and dia with Supply and Fixing new drawer made out of Ist class hard wood (teak wood) with brass knob chromium plated 40mm dia as approved by GE(I), complete all as shown on drawing specified and directed.

All as per item No. 19.1 here-in-before but replacement of bottom centre stiffener made out of Ist class hard wood (teak wood) complete all as shown on drawings specified and directed.

All as per item No. 19.1 here-in-before but replacement of bottom side stiffener with Supply and Fixing new bottom side stiffener made out of Ist class hard wood (teak wood) complete all as shown on drawings and specified and directed.

All as per item No. 19.1 here-in-before but replacement of rubber ring with screw steel with Supply and Fixing new hard rubber ring of superior quality fixed with screws steel of suitable size of the bottom of leg complete all as shown on drawing and directed.

Supply and Fixing new bracket with 4 Nos steel screws suitable size of Ist class hard wood (teak wood) of size 100mm x 100mm x 3mm complete all as directed.

REPAIR TO TABLE CARD WOODEN 900MM X 900MM X 760MM (FD - 352)

Removing/taking out carefully of old existing unserviceable/broken/damaged table top of table 900mm x 900mm x 760mm of any description in any position and replacement of the same with Supply and Fixing new table top of 18mm thick pre-laminated particle board BWR exterior grade with and including 6 mm thick teak wood beading around, the top, made to shape fixed in position all as shown on drawing, polishing of new existing portion specified and directed.

All as per item No. 20.1 here-in-before but replacement of leg with Supply and Fixing new leg made out of Ist class hard wood (teak wood) complete all as shown on drawing, specified and directed.

All as per item No. 20.1 here-in-before but replacement of long rail of table frame with Supply and Fixing new long rail make out of Ist class wood (teak wood) complete all as shown on drawing specified and directed.

All as per item No. 20.1 here-in-before but replacement, short rail of table frame with Supply and Fixing new table frame short rail made out of Ist class hard wood (teak wood) complete all as shown on drawings specified and directed.

All as per item No. 20.1 here-in-before but replacement of rubber ring with screw steel with Supply and Fixing new hard rubber ring of superior quality fixed with screws steel of suitable size of the bottom of leg complete all as shown on drawing and directed.

Supply and Fixing new bracket with 4 Nos steel screws suitable size of Ist class hard wood (teak wood) of size 100mm x 100mm x 3mm complete all as directed.

REPAIR TO CHAIR DINING WITH LONG BACK (FD - 357)

Removing taking out carefully existing unserviceable broken back leg of the chair dining with long back of any description in any postion & replacement of the same with new back leg of 1st calss hard wood (trak wood) made to shape, fixed in position all as shown on drawing spefcified and directed.

All as per item 21.1 here-in-before but for front leg complete all as specified and directed.

All as per item No. 21.1 here-in-before but replacement of side rail with Supply and Fixing new side rail made out of Ist class hard wood (teak wood) with holes for weaving. The spacing of holes shall match with the existing rail on other side complete all as specified and directed.

All as per item No. 21.1 here-in-before but replacement of front and back rail with Supply and Fixing new front or back rail made out of Ist class hard wood (teak wood) with holes for weaving. (The spacing of holes shall match with the existing rail on other side) complete all as specified and directed.

All as per item No 21.1 above but replacement of stiffener with Supply and Fixing new stiffener made out of Ist class hard wood (teack wood) complete all as shown on drawings.

All as per item No. 21.1 here-in-before but replacement of back strip with Supply and Fixing new back strip made out of Ist class hard wood (teack wood) complete all as shown on drawing.

All as per item No. 21.1 here-in-before but replacement of rubber ring with Supply and Fixing new hard rubber ring under the leg, superior quality with steel screw of size 20mm long complete all as shown on drawings and directed.

REPAIR TO TABLE DRESSING GENTS (FD - 379)

Dismantalling/taking out carefully broken top of exisiting table dressisng gents of any description in any position and replacement of the same with Supply and Fixing new top of table using 12mm thick prelaminated particle board one side laminated and other white balancing, exterior grade BWP with inclusing 6mm thick teak wood beading all round made to shape fixed in position all as shown on drawing specified ,polishing of new existing portion directed.

All as per item No. 22.1 here-in-before but side with Supply and Fixing new side of 12mm thick particle board one side teak veneered and other side commercial, exterior grade, BWP with and including 6 mm thick teak wood beading all round, made to shape, fixed in position complete complete all as specified and directed.

All as per item No. 22.1 here-in-before but bottom with Supply and Fixing new 12mm thick veneered particle board commercial BWP grade complete all as specified and directed.

All as per item No. 22.1 here-in-before but mirror with Supply and Fixing new mirror having size 380mm x 760mm x 5mm thick complete all as specified and directed.

All as per item No. 22.1 here-in-before but back frame with Supply and Fixing new back frame made out of 45 mm x 40mm teak wood member and 6 mm thick commercial ply grade BWP grade complete all as specified and directed.

All as per item No. 22.1 here-in-before but back ply Supply and Fixing new 900 mm x 380mm x 12mm thick ply one side teak veneered and other side commercial complete all as specified and directed.

All as per item No. 22.1 here-in-before but knob with Supply and Fixing new chromium plated knob 25 mm dia, 24 mm length of best quality complete all as specified & directed.

All as per item No. 22.1 here-in-before but drawer with Supply and Fixing new drawer complete all as specified and directed.

REPAIR TO TABLE DINNING 6 AND 8 PERSONS (F - 273)

Dismantling taking out carefully and replacement of old existing broken top of table dining 08 persons of any description in any position and replacement of the same with Supply and Fixing new top of table of 18 mm thick pre-laminated particle board, one side laminated and other side white balancing, exterior grade BWR with and including 6mm thick tak wood beading all round made to shape, fixed in position all as shown on drawing, polishing of new existing portion specified and directed.

All as per item No. 23.1 here - in -before but top of table dining 06 persons complete all as specified and directed.

All as per item No. 23.1 here-in-before but leg with Supply and Fixing new teak wood leg complete all as specified and directed.

All as per item No. 23.1 here-in-before but long rail with Supply and Fixing new teak wood long rail complete all as specified and directed.

All as per item No. 23.1 here-in-before but short rail with Supply and Fixing new teak wood short rails complete all as specified and directed.

All as per item No. 23.1 here-in-before but stiffener with Supply and Fixing new teak wood stiffener.

Provision of rectangular bracket with Supply and Fixing new teak wood bracket of size 100 mm x 100 mm x 30mm thick made to shape fixed in position, all as shown on drawing specified and directed.

REPAIRS TO TABLE CENTRE (FD - 274)

Dismantling/ taking out carefully and replacement of old existing broken top of teapoy FD of any description in any position with supply and fixing new top of teapoy FD 18mm thick pre-laminated particle board, one side laminated and other side white balancing, exterior grade, BWR with and including 6 mm thick teak wood beading all round made to shape, fixed in position, all as shown on drawing, polishing of new existing portion specified and directed.

All as per item No. 24.1 here-in-before but leg with supply and fixing new teak wood leg complete all as specified and directed.

All as per item No. 24.1 here-in-before but long rail with Supply and Fixing new teak wood long rail complete all as specified and directed.

All as per item No. 24.1 here-in-before but short rails with Supply and Fixing new teak wood short rails complete all as specified and directed.

All as per item No. 24.1 here-in-before but stiffener complete (long and short) complete all as specified and directed.

REPAIRS TO TEAPOY FD (FD - 382)

Dismantling/ taking out carefully and replacement of old existing broken top of teapoy FD of any description in any position with supply and fixing new top of table of 18mm thick pre-laminated particle board, one side laminated and other side white balancing, exterior grade, BWR with and including 6 mm thick teak wood beading all round made to shape, fixed in position, all as shown on drawing, polishing of new existing portion specified and directed.

All as per item No. 25.1 here-in-before but leg with supply and fixing new teak wood leg complete all as specified and directed.

All as per item No. 25.1 here-in-before but long rail with Supply and Fixing new teak wood long rail complete all as specified and directed.

All as per item No. 25.1 here-in-before but short rails with Supply and Fixing new teak wood short rails complete all as specified and directed.

All as per item No. 25.1 here-in-before but stiffener complete all as specified and directed.

REPAIRS TO PEG TABLE (FD - 384)

Dismantling/ taking out carefully and replacement of old existing broken top of Peg Table of any description in any position with supply and fixing new top of table of 18mm thick pre-laminated particle board, one side laminated and other side white balancing, exterior grade, BWR with and including 6 mm thick teak wood beading all round made to shape, fixed in position, all as shown on drawing, polishing of new existing portion specified and directed.

All as per item No. 26.1 here-in-before but leg with supply and fixing new teak wood leg complete all as specified and directed.

All as per item No. 26.1 here-in-before but long rail with Supply and Fixing new teak wood long rail complete all as specified and directed.

All as per item No. 26.1 here-in-before but short rails with Supply and Fixing new teak wood short rails complete all as specified and directed.

All as per item No. 26.1 here-in-before but stiffener complete all as specified and directed.

REPAIRS TO TABLE WRITING (FD - 275)

Dismantling / taking out carefully and replacement of old existing broken top of table writing of any description in any position with Supply and Fixing new table top of 18mm thick pre laminated particle board. BWR exterior gradewith and including 6mm thick teak wood heading fixed in position, all as shown on drawing, polishing of new existing portion specified and directed.

All as per item No. 27.1 here-in-before but side including box complete of table writing with Supply and Fixing new 18mm thick particle board, one side teak face BWR grade and other side white complete all as specified and directed.

All as per item No. 27.1 here-in-before but to long rails of table writing with Supply and Fixing new top long rail made out of Ist class hard wood (teak wood) complete all as specified and directed.

All as per item No. 27.1 here-in-before but top short rails of table writing with Supply and Fixing new top short rail made out of Ist class hard wood (teak wood) complete all as specified and directed.

All as per item No. 27.1 here-in-before but drawer with knob brass chromium plated 40mm dia with Supply and Fixing complete new drawer made out of Ist class hard wood (teak wood) with knob complete all as specified and directed.

All as per item No. 27.1 here-in-before but bottom centre stiffener with Supply and Fixing new bottom center stiffener made out of Ist class hard wood (teak wood) complete all as specified and directed.

All as per item No. 27.1 here-in-before but leg with Supply and Fixing New leg made out of Ist class hard wood (teak wood) complete all as specified and directed.

All as per item No. 27.1 here-in-before but bottom side stiffener with Supply and Fixing new bottom side stiffener made out of Ist class hard wood (teak wood) complete all as specified and directed.

CHAIR WRITING, CHAIR CB OFFICE WOODEN, CHAIR DINNING, STOOL DRESSING, CHAIR EASY (FD - 279, FD - 280, FD - 282 & FD - 229) Taking old worn out cane and M&L for re-canning of chairs wooden/steel (any type), Stool dressing, Bin Soil linen in Godrej pattern with 2.0mm wide, 0.4mm thick and beading with 4mm wide half round white plastic cane all as specified and shown on drawing.

SOFA SET 05 SEATER (FD - 281) Removing of old unserviceable cushion and tapestry cloth and providing new 100 mm thick cushion of approved Superior quality (Sleep Well) of 32 density covered with best quality tapestry cloth as approved by Engr-in-charge

SOFA SET 05 SEATER (FD - 281) Removing of old unserviceable tapestry cloth from cushion and providing new tapestry cloth duly stitched approved Superior quality as approved by Engr-in-charge.

SOFA SET 03 SEATER (FD - 281) Removing of old unserviceable cushion and tapestry cloth and providing new 100 mm thick cushion of approved Superior quality (Sleep Well) of 32 density covered with best quality tapestry cloth as approved by Engr-in-charge

SOFA SET 03 SEATER (FD - 281) Removing of old unserviceable tapestry cloth from cushion and providing new tapestry cloth duly stitched approved Superior quality as approved by Engr-in-charge.

SOFA SET 01 SEATER (FD - 281) Removing of old unserviceable cushion and tapestry cloth and providing new 100 mm thick cushion of approved Superior quality (Sleep Well) of 32 density covered with best quality tapestry cloth as approved by Engr-in-charge

SOFA SET 01 SEATER (FD - 281) Removing of old unserviceable tapestry cloth from cushion and providing new tapestry cloth duly stitched approved Superior quality as approved by Engr-in-charge.

M&L for polishing for the following wooden furniture including preparation/cleaning of old polished surfaces by scraping with fine abbressive cloth and applying two coats of french/spirit polish of the existing shades all over the wooden exposed surfaces direct in vision etc for Chair writing/CB Office/Chair dining/Chair Easy /Chair Draftman (FD - 250, FD - 261, FD - 262 & FD - 229) complete all as specified and directed.

All as per item No. 35 here-in-before but Peg Table / Table bed side/ Stool dressing (FD - 236, FD - 252 & FD - 248) complete all as specified and directed.

All as per item No. 35 here-in-before but Sofa set for 5 person (one piece of three seater and two pieces of single seater)(FD - 281) complete all as specified and directed.

All as per item No. 35 here-in-before but Sofa set for 3 person (FD - 281) complete all as specified and directed.

All as per item No. 35 here-in-before but Sofa set for 1 person (FD - 281) complete all as specified and directed.

All as per item No. 35 here-in-before but Table center / Teapoy / Table dressing gents and ladies (FD - 274 FD - 382 FD - 379 & FD - 378) complete all as specified and directed.

All as per item No. 35 here-in-before but Table dining 6 persons (FD - 269) complete all as specified and directed.

All as per item No. 35 here-in-before but Table dining 8 persons (FD - 376) complete all as specified and directed.

All as per item No. 35 here-in-before but Table office officer wooden complete all as specified and directed.

All as per item No. 35 here-in-before but Side Board (FD - 371) complete all as specified and directed.

SARGAM ENTERPRISES

Mahesh Traders

A S ENTERPRISES

jkconstruction

Sunny Furniture Centre

MISHON TRADING CORPORATION

Bidder Name

MISHON TRADING CORPORATION