ADDN ALTN OF QTR AT BHIM ROAD (FAFA) UNDER GE (WEST) JRC

Amount

Dismantling of brick tiles single layer as in roof covering complete all as specified

Demolition of mud in roofs any thickness including plastering and leeping (whether full thickness removed or only a part there of)

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, or removing any type of existing treatment complete all as spd.

M&L for PCC 1:2:4 type B-1 (20mm graded aggragate) as roof padding concrete to bring the extg slab in slope of 1:40 complete all as specified

(i) M&L 15mm thick rendering with water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc on wall in CM 1:4 on brick/concrete surface and finishing the surface even and smooth with out using extra cement (ii) Providing and applying Epoxy primer (02 fast component resin of hardner) on the prepared surfacev @200gm per Sqm. (iii) Providing and applying Liquid Polyurea - PU based hybrid elestomeric water proofing membrane at existing/newly constructed roofs. Double coat is required on the smooth and cleared surface @ 1.50Kg per Sqm. (iv) After coating of primer of two coats of ULTRON (US) a proper protective plaster/layer is to be done by laying Geo textile and 40mm screed on the top of final coating. (Make - Asian Paints, BASF & SIKA) Note:- Ser No (i) to (iv) : The application shall be done by the authorised applicator of the manufacture with a letter of proof stating the authenticity of the applicator firm.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, benching rounded or chamfered on edges complete.

Taking down chowkhats or frame with shutter without taking off shutter from the frame area not exc 1.5 Sqm each all as specified.

All as above but not exc 1.5 Sqm and not exc. 4 Sqm each.

Taking down shutters of any description not exc 1 sqm all as specified.

Taking down shutters of any description exc 1 sqm but not exc 2 sqm all as specified.

S&F solid PVC door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M. S Square tube, suppling& fixing in opening as per specification & drawing.

S&F Factory Made Solid PVC moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

S&F PVC cupboard shutter (Front or shelf) made of 18/19 mm pre-laminated board (Decorated outside and plain white/cream on inner side) fixed with PVC cleats etc. complete all as specified and directed.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, size 125x 60 mm complete all as specified.

S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate etc, size105 x60mm complete all as specified

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65x 100 mm, one or more rebates comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

Providing and fixing factory made single extruded WPC(Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistur proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge.

S&F factory made 35 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F factory made 2nd class glazed and skelton shutters 35mm thick open rebated and prepared to receive glass,gauge etc (without sash bars) edging of framing plain, chamfered or rounded with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Pt-I, Section 8, Clause 8.24(a).

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60x25mmsingle rebated comprises gauged skelton shutter ERW sec 50x20mm and 1mm thick with two open able leaf consisting two Nos sash bars of T section 20x3mm completed welded to frame with one vertical mullion of ERW box type T section of size 60x25mm and 1.25mm thick incl cutting holes and making good dismantled portion PCC 1:2:4 type B1 four Nos for each window incl following fittings weld to frame shutter (a) hold fast, 150mm long of 12mmx3mm made to shape-04 Nos per window (b) handle of Z sction 20x25mm, 100mm long 01 Nos per leaf (c) MS Tower bolt 150mm long of 12x3mm made to shape-04 Nos per window (b) handle of Z section 20x25mm, 100 long stoper-01 No per leaf () MS pintal of hinges of size 75mmx12mm-02 Nos per leaf (g) fabrication & fixing arrangement as per Drg No. CEJZ/TD-06-07. Note : wire mesh and painting shall be measured and paid separately under appropriate item.

All as per item No 20.00 her-in-before but glazed steel windows.

M&L Galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1:18 mm and fixed with tinned tacks or galvanised wire staple.

S&F tinted black sheet glass 4.8 mm thickness, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane. Note :- Colour of glass as directed by Engr-in-Charge.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple complete all as specified and directed.

M&L for framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors,ladders, framed balusters, walk ways; railings; framework of water tanks and similar work conforming to Fe 410 complete all as specified.

M&L for PCC Type B0-1:2:4 using 12.5mm graded aggregate as in pressed steel frame, hold fasts and similars articles

M&L framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming Fe 410 -W (GdeE- 250) quality-A, complete all as specified.

S&F 40m dia mild steel cup board knobs fixed with nut, screw and washer of brass polished

M&L Hasp and staple safety type aluminum anodised 100 mm size with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified

S&F Figured glass pin head type glazed with oil putty in squre n-exc 0.5 Sqm in Each pane 4mm thick .

S&F 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed.

S&F 100mm butt hinges, heavy weight, cold rolled mild steel, and fixed.

S&F 150 mm aluminium handles, cast type anodised

S&F 100 mm aluminium handles, cast type anodised

S&F 200mm long aluminum anodised barrel Tower bolt of extruded section

S&F 150mm long aluminum anodised barrel Tower bolt of extruded section

S&F Aluminum alloy anodised sliding door bolt 300mm long with hasp, staple (bolt tupe and fixing of clips of sheet, fixing bolts etc.

S&F Mild steel sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed etc.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor.

S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete.

S&F door closer hydraulically regulated (Aluminium extruded section body), designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

M & L for Preparation of new surfaces of wood of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamelled paint over one coat of pink primer.

M & L for Preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamelled paint over one coat of red oxide

M & L for Preparation of old steel surface of any description over 10 CM width or girth and applying one coats of synthetic enamel paint complete all as specified

M & L for Preparation of old wood and wood based surfaces of any description over 10CM width or girth and applying one coat of synthetic enamel paint over a coat of pink primer including removal of existing finish complete all as specified.

Demolition of reinforced cement Concrete above ground level n. exc 15 cm thick complete all as directed.

M&L for reinforced cement concrete type B0 1:2:4 (20 mm graded aggregate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, chajjas, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape reqd, incl cranking, bending spirally for hooping for columns, hooling ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs etc not exc 200mm thick (Horz or sloping) flat rough finished surface of concrete

Demolition of brick built in cement mortar including all quoins arches pillars etc.

M&L Brick work with sub class 'B' bricks straight or curved in plane exc 6cm mean radius built in cm 1:4.

Ditto but except brick.

Demolition of cement Concrete(unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) or as in sunken

M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions of walls shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and as junction of walls.

M&L for 25mm thick cement concrete type B-1, 1:2:4 using 20mm graded aggregate as in sub floor complete all as specified.

M& L for machine cut kota stone slab flooring in steps/ stairs 18-20mm thick over and incl 20mm thick cement screed base laid in cm 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete all as specified and directed.

Ditto but in riser/skirting of stairs incl 10mm thick screed in cm 1:3 and taking down cement mortar complete all as specified and directed.

SM & L for Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite as per directed by EIC.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing), remoing serviceable tiles to store and rubbish off the premises.

M&L non skid ceramic coloured tiles 7 to 8mm thick joint free edge cut area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 sqm set and jointed in neat cement slurry in floor and pointed in colour cement to match the sade including sceed bed or bedding layer of mortar 15 mm thik 1:4. Note :- Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-Charge

S&F Light shade coloured vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm, in floors and scantling etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed cement mortar 1:6 complete all as specified and as directed. Note:- Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-Charge

M&L Glazed ceramic coloured tiles in vertical surface 450x300x7 mm, 7 mm thick set and jointed in neat cement slurry and pointed in white cement with pigment to match the surface over 10mm thick screed in C:M 1:4 all as specified. Note: Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-Charge

Demolition and breaking up of drain pipes (salt glazed ware or AC or reinforced cement concrete), set in cement mortar, dia of pipe100/75mm, complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/ floor.

S&F PVC SWR bends of 110 mm bore.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/floor.

S&F PVC SWR bends of 75 mm bore.

S&F 110 mm PVC (SWR) junction single, (Single T) equal or unequal

S&F PVC SWR branch piece, single (single Y) equal or unequal of 75 mm bore.

S&F PVC SWR vent cowl 110mm bore.

S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia all as specified

Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 15mm bore

Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 20mm bore .

S&F Tube 'medium grade' galavanised, with all fitting and fixed complete to walls and ceiling etc 15mm bore.

All as per Ser item No 74.00 above but 20mm bore.

M&L Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

S&F Rotational moulded polythene water storage tanks(cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 500 ltr capacity incl dismantling water tanks and removing to store

S&F Rotational moulded polythene water storage tanks(cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 1000 ltr capacity incl dismantling water tanks and removing to store

S&F Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 20mm bore.

S&F in repair angle stop valve cast copper alloy fancy type , screwed down high pressure with capstan head, screwed both ends for iron pipes or for union & fixed in 15 mm bore pipe.

S&F concealed stop cock fancy type chromium plated with cast copper alloy screwed down high pressure with or without lattered hot and cold with long screwed shanks and fly nuts fixed in repair 15mm bore.

S&F 15mm dia bore angle cock two way Cast copper alloy chromium plated, fancy type with long shank & cup all as specified and fixed in repairs.

S&F as in repairs brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed for iron pipe 15mm bore

S&F as in repairs wash basin mixer, cast copper alloy, with capstan head chromium plated screwed down high pressure with or without lattered hot or cold with long screwed shanks and fly nuts screwed for iron pipe 15mm bore

S&F PVC connection 15mm bore size with PTMT nuts of length 45cm.

S&F PVC valveless syphonic action type flushing cistern, low level white with inlet ball valve flaot and handle including brackets. 10 ltr capacity in repair.

S&F Plastic water closed seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium plated or aliminished hinging device fixed in repair.

S&F as in repairs Viterous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistern and floor pipe) complete.

S&F in repair vitreous china wash hand basin (pedastal pattern) white flat back, size 550mmx400mm fixed on and including cast iron cantilever brackets 32mm dia brass waste coupling and including fixing of tap waste fitting and union complete all as specified and as directed . Note: pillar tap shall be measured as supply only under respective items

S&F as in repair Brass chromium plated shower rose 125mm complete.

S&F 4mm thick superior quality straight shelve , made of transparent toughened glass, size 60cm long complete all as specified and as directed.

S&F towel rack 24 inch CP type with all fittings and fixed to walls complete all as specified.

S&F CP/Brass peg set of six fancy type complete all as specified.

S&F 32mm dia waste pipe for WHB complete all as specified.

S&F in repairs brass chromium plated health faucet for pedestal pattern water closet including PVC flexible pipe alongwith complete necessary fittings all as specified and directed by the Engr- in- Charge.

S&F in repairs coloured PVC toilet cabinet looking mirror of size 440x325x120mm in replacement of existing looking mirror/wooden cabninet and repairing the disturbed surfaces to match with existing complete all as specified.

Supply in fixing in repairs Stainless steel sink with drainage board made out of 1mm thick sheet for kitchen or laboratory with plugs, washer and wastes pipe , cast iron cantilever brackets and connecting union over all size 915 x 460 mm with bowl size 410 mmx 330 mmx 160 mm complete all as specified.

S&F in repairs Chromium plated grating 75/100mm dia circular of approved make and fixing with cement mortor 1:3 on Nahani trap or floor trap.

S & F as in repair for pre-fabricated stainless steel plate rack made out of 1 mm thick stainless steel plate jointed with brass screws of size 600 x 750mmx 250mm complete .

S&F Fixed in repairs brass chromium plated tubular towel rail 20mm dia(D) type 60cm long between flanges complete.

S&F Bib taps chromium plated fancy type, cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repair 15mm bore.

S& F 1mm thick Stainless steel hollow curtain rod with brackets and side doom fixed with all necessary drilling/fixing wooden/plastic cleats in wall complete all as specified and directed.

S&F 4mm thick superior quality shelves (corner), made of transparent acrylic sheet, set of three, size 30x30cm, 25x25cm, 20x20cm complete all as specified and as directed.

S&F in repairs stainless steel toilet paper holder with gutties and steel screws on walls as directed and approved complete all as specfied

S&F stainless steel soap dish complete all as specified.

Taking down cement plaster on wall built in cement or cement lime mortar incl raking out joints, hacking for key, scrubbing out with water etc. complete.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 without using extra cement.

M&L rendering 5 mm thick on fair faces of brick work or concrete surfaces in ceiling in CM 1:3 on ceiling and finishing the surface even and smooth without using extra cement.

M&L 15mm thick rendering @ 3% WPC on wall in CM 1:4 on brick/concrete surface and finishing the surface even and smooth with out using extra cement.(Water proofing compound shall be mixed as per manufactured instruction and paid separatly as per respective items)

M&L10mm thick rendering in cement mortar 1:4 on RCC chajjas, facia , roof projections, parapet walls etc over cement slurry, rendering is to be even and smooth with out using extra cement (upto 3 storey bldg) complete all as specified and directed

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV esistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for preparing new plastered surfaces of ceilling and applying three coats of white wash.

Preparation of new surface of wall with Birla putty filling on plastering surface and applying two coat of oil emulsion distemper white or printed on walls.

Complete removal of existing treatment on wall and applying two coat of oil emulsion distemper (white) on one coat of putty filling on walls etc (Surface finished even and smooth) complete all as specified and as directed by Engr-in-Charge. Note :- Colour as directed by EIC

Material & Labour for applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV esistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces incl preparation.

M&L for preparation of old surfaces of ceiling including complete removal scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including cornices, pilasters etc (plastered or unplastered surfaces) and applying two coat of white (lime) wash complete all as specified and as directed by Engineer-in-Charge.

M&L preparation of old decorated surface of wall applying one coat of white wash complete all as specified and as directed by Engineer-in-Charge.

M&L preparation of new decorated surface of wall applying two coat of white wash complete all as specified and as directed by Engineer-in-Charge.

Carefully chipping, removing existing loose/ damaged concrete with plaster from Columns/slabs/beams by low impact high frequency hammer/chipper without damaging the existing sound concrete and exposing old reinforcement upto 10mm beyond corroded reinforcement bars using electrically operated diamond concrete saw blade making the edges straight and even and cleaning it by wire brush and then by air blower and removal of rubbish outside MoD lad complete as specified as directed by Engr-in-charge.

Cleaning all existing reinforcement bars in Columns/slabs/beams with wire brush/rotary wire brush to make entire circumfernce surface of bars free from rust scales, loose material, dirt etc. complete and applying alkaline rust converting primer on the existing rebar in two coats conforming to ASTMB117 & ASTMG6 and allowing it ti react with rust for 6 hrs and form a corrosion resistant, insoluble and adherent protective layer including cleaning the reinforcement, wire brushing to remove the rust spalls, complete as per manufactures instructions all as specified and directed. the rust converter shall have a minimum pH of 7 and shall be able to convert both hematite and magnetite forms of rust shall pass 400 alternate immersion cycles in 3% nacl. (Mode of measurement : per sqm of breaking area of concrete.) Make : Asian Paints Apcorep Rust or equivalent make approve by E-in-C's branch.

Providing and appllying anti-corrosive coating APCOREP RUSTCOAT RB (CSIR/CBRI know how) in two coat with time interval of minimum 6 hrs. the coating shall have Ecorr value of 4 mV aganst SCE in 3 NaCL for 100 hrs and electrochemical evaluation of max 0. mA /cm. This coating shall be applied over APCOREP RUSTREM cated rebars.

Providing & applying a coated of structural grade epoxy bond coat Smart Care Epoxy Bounding agent having excellent water and alkali resistance and has long tack fee time of more than 120 minutes and shear bond strengh of 4 Mpa to the prepared concrete surface to be repaired / strengthened. This is applied prior to the application of polymer repair mortar/ epoxy mortar/ micro concrete to have monolithic action between old concrete surface and new concrete surface.

Drilling Holes of 12mm dia up to 100 mm deep holes in structural members at the interval of 300 mm in staggered manner or along the crack in Reinforced Concrete (RC) structural element including cleaning of the holes by air blower and inserting 12 mm dia NRV (non Returnable Balve) nozzle compatible with epoxy injector and having machined external end to receive outlet of Grouting Gun. Fix inside the hole by applying thixotropic epoxy adhesive to ensure complete sealing and allow curing the system for minimum of 8 hrs before Grouting including nozzle projections, excess putty, if any over concrete element by griding, leceling and finshing the external surface, after completion of the work , etc. complete all as spcified and directed.

Providing and repairing the damaged concrete portion / Surface preparation with single component ready to use, repair mortar SMARTCARE REPAIR MORTAR caspable of applying 20 mm avg. thick in single layer initially by hand finishing with trowel, carefully compacting the same around the rebars and finishing to bring it in line with existing surface type: Ready to use single component Polymer modified repair mortar, Flexural Strength ASTM-C-348-Min.8 MPa, Bulk Density-1.5 to 1.6, Compressive strength (Typical value)1Day-8 MPa min, 28 Days-40 MPa min, LIC (Critical Stress Intensity Factor) : Increases by 50% for 15% dosage against control Facture Energy (r1) joules: inceases by 200% for 15% dosage. Note :- Smart Care mortar will be applied approximately 0.12 Kg/Sqm.

Demolition of cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed

M &L for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WCs etc shall be as under:- (i) Application of Two component acrylic modified cementitious coating (aa) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coating and achieve a gripping profile that is clean, dry and free from laitance and dry other form of surface contamination. The installation instructions in manufacture's published literature should be strictly complied with, including but not limited to the following:- (bb) Chipping out any visible cracks in "V-Groove" pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/Dr Fixit 302 SBR latex/ Perma latex SBR/FOSROC Nitabond SBR latex/Asian paint latex as required. Final cleaning of surface with power grinder, wire brush, hair brush & vacuum pressure if required. (cc) Dampen all surfaces immediately ahed of application of Acrylic modified Cementitious coating of sika Top Seal-107/Brush Bond FOSROC/Dr Fixit/STP/CICO. (dd) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified cementitious coating of SIKA Top Seal-107 /Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer's instructions. (ee) Apply glass fabric sheet of SIKA Fab 1/FOSROC/Dr Fixit/STP whilst the first coat is wet. (ff) Once touch dry, apply second coat of Acrylic modified cementitious coating of SIKA Top Seal -107 /Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer's instructions on the entire area. (gg) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (hh) The waterproofing coating should be taken to a height minimum 300mm above the finished floor level on the vertical surfaces. (jj) It is essential to cure Acrylic modified cementitious coating immediately after application (minimum 6-8hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking. (kk) A protection plaster 12-15mm thick) in CM 1:3 admixed with appropriate integral water proofing compound has to be applied on the walls. Admixture: SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO conforming to IS 2645. Providing and applying a protection screed of 50mm thick 1:4, cement sand mortar admixed with SIKA Plastocrete over the applied water proofing coating on horizontal surfaces. Admixture: SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO conforming to IS 2645. (ll) All the corners and joints should be pretreated with an elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansions zone in the centre of Make SIKA Seal Tape/FOSROC/Dr Fixit/STP. (mm) The membrane has to be protected in accordance with the manufacturer's recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer's recommendations. (nn) Waterproofing treatment has to be carried out through applicators authorised by the respective manufacturer's and approved by GE. (ii) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealent. (iii) All CI traps in sunken slab to be enclosed with PCC 1:1.5:3 (Min 15cm) all around. (iv) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40mm stone aggregate) complete all as specified. (v) Providing drainage spout pipe GI pipe 40mm dia bore light grade upto outside of outer wall ( Approx 450mm to 600 mm long ) including cutting to existing wall and making good the disturbed surface complete all as specified and directed. (vi) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. Note:-Item No (iv) ,(v) &(vi) shall be measured and paid separately.

M&L 25 mm thick cement concrete flooring type B-1, 1:2:4 using 20 mm graded stone aggregate finishing cement concrete surface even and smooth without using extra cement.

M&L for cement concrete type E - 2, 1:5:10 (using 40 mm graded stone aggregate) as in sunken flooring.

M & L for 50mm dia GI pipe,med grade beveled cut at both ends by making hole in walls sunken portion aprox above the RCC slab and ceiling finished the hole with cement plaster 1:2 to match with existing surface complete etc.(Measured for cutting holes shall be paid in concerned sch item)

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft soil.

M/L 100mm thick cement concrete 1:4:8, type D-2 using 40mm graded stone aggregate.

M & L for 25mm thick Sand cushioning under paver block complete all as specified and directed.

M&L machine pressed precast coloured concrete coloured interlocking paver blocks any shape and size confirming of IS 15658: 2006 of 60mm thick , M-35 laid and jointed with grey cement and pigment.

Removing excavated soils n.exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point.

Mild steel, plain 1.00 mm thick , black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing withplain 40 mm lap joints with riveted or welded seams,including bending or turning up, mitred angles, etc. as required complete all as specified

M&L PVC modular kitchen cabinet box type made of 18mm PVC/WPV board of appx size (2.00 x 0.80 x 0.60) mtr including all accessories like SS trolleys (Min 08 Nos), telescopic sliding channel steel handles, knobs, hinges etc complete all as specified and directed by Engr-in-Charge. Note :- The front superficial area considered as accounting unit for payment.

M&L PVC modular kitchen cabinet box type made of 18mm PVC/WPV board of appx size (1.20 x 0.16x 0.60) mtr including partitions, front top hung glass shutters, hinges etc complete all as specified and directed by Engr-in-Charge. Note :- The front superficial area considered as accounting unit for payment.

Taking down carefully existing point wiring of any type (i.e on wooden batten, surface conduit, casing capping or concealed conduit except existing conduit) complete for light, fan, socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets wooden batten, conduit etc including accessories such as wooden gutties/ rawal plug, screw etc including removing materials from site for taking credit of unserviceable items and re-fixing the serviceable items as per schedule and making good disturbed surface of walls, floors etc, complete all as specified and directed.

Taking down unserviceable Submain of any size as directed by Engineer-In-Charge.

Taking dowm DB TPN 4 way along with all MCBs and refixing it after repair wk complete all as specified and directed.

M&L for point wiring with 1.5 sqmm, PVC insulated but sheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit medium grade 20mm dia (minimum) or higher size as specified and cutting chasing on wall complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc/ fittings ISI marked for modular fittings and brass screws and cup washers including 1.5 sqmm stranded copper conductor PVC insulated FRLS cable green in colour as continuous earth conductor connected to common earth and earth dolly with all accessories and making disturbed surfaces good complete all as specified and directed. Note : Cost of Metal boxes and modular accessories like cover plates will be paid seprately in respective items) (a) Fan point/ exhaust fan point / one light point / bell/ buzzer controlled by one switch/ bell push.

(b) One light point controlled by two Nos of two way switch.

(c) One socket outet point 5 amps on the same board.

(d) One socket outet point 5 amps on the independent board.

All as per item No. 142.00 hereinbefore but wiring with using cable 2.50 sqmm size copper wire FRLS and earth wire of PVC insulated (Green colour) 2.50 Sqmm size copper wire for one 6 pin socket outlet, 16 Amperes on independent board.

Supply and fixing modular metal flush box 1/2 module complete all as specified and directed.

Supply and fixing modular metal flush box 3 module complete all as specified and directed.

Supply and fixing modular metal flush box 4 module complete all as specified and directed.

Supply and fixing modular metal flush box 6 module complete all as specified and directed.

Supply and fixing modular metal flush box 8 module complete all as specified and directed.

Supply and fixing modular metal flush box 12 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame, 1 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame, 2 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame, 3 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame, 4 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame, 6 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame, 8 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame,12 module complete all as specified and directed.

Supply and fixing modular Dummy plate complete all as specified and directed.

Supply and Fixing Modular switch 6 Amp 1 way 1 module size complete all as specified and as directed by Engr-in-Charge.

Supply & Fixing of Modular switch 6 Amp 2 way 1 module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Modular switch 16 Amp 1 way with indicator 1 module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Modular socket shuttered 6 Amp 2/3 pin combined 2 module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Modular socket 16Amp multipurpose type 2 module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Modular Fan regulator step type 120 watts 2 Module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Modular bell switch 6 Amp 1 module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Ceiling rose, surface bakelite 3 terminal, 240 volts, 5 Amps with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size ,complete ,all as specified.

Supply and fix MCB DB, TPN 4 way double door with suitable 200 amps rated bus bars , Neutral links , blanking plates

S/F MCB TPN 40 Amps 415 volts

Supply & Fixing MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type

S & F lamp holder, PVC / polycarbonate type insulated body with back plate suitable for batten / angle fittings complete all as specified and directed.

Supply & fixing decorative wall light fixture made up of polycarbonate/glass incl 9 W bulb white/warm all as specified and directed.

Supply and fixing of single phase call bell ‘DING DONG’, AC 230 volts single pole fixed over and including pressed steel sunk box of size 175 X 100 mm duly covered with 3 mm thick bakelite sheet complete all as specified and directed.

M & L for concealed submain wiring Two Single core multi stranded PVC insulated but sheathed copper conductor of grade 1100 Volt. FRLS cable of size 4 sq mm (Red/Blue/Yellow for Phase and Black for neutral) and including fixing arrangement with wall incl electrical grade PVC conduit of desired colour suitable size PVC conduit as mentioned in SSR Part I and 4 sqmm multistranded copper conductor cable PVC sheathed green coloured for earthing with complete accessories duly connected with earth duly complete all as specified and directed. Note - (i) Three run of cable and one run of PVC conduit measure as single run. (ii). Groove Cutting, pinning and plastering of disturbed surface etc shall deemed to be included in the quoted rate.

M & L for sub main wiring with 1100 volt grade two single core FRLS Wire PVC insulated and unsheathed cable with stranded copper conductor 10 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 10 sqmm multi - stranded copper conductor as earth wire in green colour complete all as specified and directed. Including taking down old unserviceable sub main wiring. Note : Four runs of 10 sqmm PVC FRLS multi stranded copper cable wire and One run of 10 sqmm PVC FRLS multi stranded copper cable earth wire and One run (01 meter) PVC conduit of suitable size ISI mark will be measured and one unit length.

Supply & fixing of 14 Watt Batten luminaire with Polycarbonate Housing with high quality extruded polycarbonate diffuser. The luminaire should have a CRI > 80 and CCT of 6500K. The luminaire shall be compliant with IP20 and IK02 classification. Luminaire shall be designed to emit at least 2100 nominal lumens and an outstanding System efficacy of at least 150 lumen/watt and maximum system wattage of 14 Watts. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient temp 45 deg C. The electronic driver used shall have a power factor >0.95 and THD <15% and suitable for an operating voltage range of 140-270V AC. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters.

Supply & fixing of 20 Watt Batten luminaire with Polycarbonate Housing with high quality opal finish diffuser. The luminaire should have a CRI > 80 and CCT of 6500K. The luminaire shall be compliant with IP20 and IK02 classification. Luminaire shall be designed to emit at least 2000 nominal lumens and an System efficacy of at least 100 lumen/watt and maximum system wattage of 20 Watts. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient temp 45 deg C. The electronic driver used shall have a power factor >0.95 and THD <10% and suitable for an operating voltage range of 140-270V AC. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete, with CCT of 6000k suitable for domestic application, 240 Volts, 50 Hz, and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete all as specified and directed.

S & F SITC of high-quality integrated LED Street Light with a minimum system lumen of4750 Lm and system wattage not exceeding 45W with a nominal efficiency 105 lumen/watt. CCT of 5700K with SDCM of < 5 and CRI >70. The housing should be of non-corrosive high-pressure die-cast aluminum with high efficiency LEDs as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with PF > 0.95. Lifetime of 50K hours @L70. The Luminaire should have Powered by integral, Isolated LED electronic driver (SMPS based constant current supply) with lower THD, Output Open / Short Circuit protection, Phase to Phase protection (Operation at 440 V AC), Over Voltage protection, Surge Voltage protection upto 4 kV.Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/ULaccredited lab to verify above parameters including bracket and fixing clamps etc and connecting electrical to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 corecomplete all as specified and directed.

Taking down and refixing of geyser (Electric Water heater storage type) of capacity 25 Lts , keep in safe custody as per srl No. 1, after B/R repairs. Note : Cost of minor petty items if required such as nut bolt/Pvc pipe is included in quoted rate.

Supply and fixing ceiling fans in replacement complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 with brushless direct current motor (BLDC) complete all as specified and directed.

Taking down ceiling fan 1200/1400 mm size , as per item srl no. 1 after B/R repairs. Note: Cost of minor petty items if required such as nut bolt/clamp is included in quoted rate.

Refixing ceiling fan 1200/1400 mm size , as per item srl no. 1 after B/R repairs. Note: Cost of minor petty items if required such as nut bolt/clamp is included in quoted rate.

Taking down only exhaust fan/ fresh air, keep in safe custody as per item srl No. 1 after B/R repairs. Note: Cost of minor petty items if required is included in quoted rate.

Fixing only exhaust fan/ fresh air, keep in safe custody as per item srl No. 1 after B/R repairs. Note: Cost of minor petty items if required such as nut bolt/clamp is included in quoted rate.

Supply and Fixing metal enclosure (plug & socket type DB) complete including single pole and neutral enclosure with two pin, earth plug and socket complete with one SP MCB of capacity 20 Amp, 10 KA all as specified and directed.

Supply & fix Exhaust fan Metalic body, Heavy duty, AC 230/240 V, 1200 to 1500 RPM of size 300 mm sweep with louvers , incl making opening in wall grouting the nut bolts for fixing the exhaust fan ,cement work and making disturbed surface good, connecting to ceiling rose complete all as specified and directed.

S & F high speed wall mounted fan of sweep size 300 mm complete with wide oscillation with motorised control including fitting and fixtures as per site requirement and two core PVC insulated, PVC sheathed copper conductor for connection all as specified and directed.

M & L for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on and taking down old one complete all as specified and directed. Note :- (i) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.

M/s GURFATEH BUILDERS (BID ID -3501611)

M/S Kuldip Construction Co. (BID ID -3504403)

BHARAT ENTERPRISES (BID ID -3502084)