Construction of proposed convention/banquet hall at Karna Lake, Karnal (Work for external electrification and substation work at Karna Lake, Karnal)

Amount

VCB / HT PANEL (1 Incomer & 2 Outgoings)

Supplying, installation, testing & commissioning HT panel 11kv 3 phase 50Hz AC supply, indoor type, cubical, metal clad, free standing, floor mounting with MS base frame, future extensible made out of AluZinc sheet which has corrosion resistance sheet not less than 2mm, gland plate 3mm, pretreated in seven tank treatment, epoxy powder coated as approved by EIC, finish not less than 90 micron, totally enclosed degree of protection IP4X& fully interlocked, horizontal draw out trolley mounted (separate trolley not accepted), horizontal isolation as per IS 13118, IEC 62271-200 as amended up to date, common copper bus bar , interlock, bus bar shutter to prevent unsafe operation, designed and constructed to facilitate cleaning, inspection, repair and mtc and shall be open and close the breaker compartment door with rubber mat laid in front of panel, corrosion resistant hardware, suitable air insulated but encapsulated electrolytic continue rating copper bus bars of 800.Amps capacity.HT Panel to be Internal arc type tested for 25kA as per IEC 62271-100, Vacuum Bottle must be tested for 100 short circuit operations. Make- CMKL / Siemens(Nx-AIR), ABB(ZS-1), SCHNEIDER(PIX)

The HT panel shall be consisting of following,

INCOMER VCB

Supply, installation, testing and commissioning of VCB as per IEC-62271-100, 11kV, 630A, 3 Pole, 500mva for 3Sec, Electrically and manually Operated draw out Type, single break, trip free mechanism, auto/manually closing breaker, complete with self contained, fully interlocked, rack in and rack out mechanism, with epoxy encapsulated vacuum bottle, required Aux. Contacts, Limit Switches for Test & Service Position.

Accessories

Spring charging motor : 230V AC , Handle for manual spring charging

Closing coil : 110V DC

Shunt trip coil: 110V DC

Space heater with thermostat

Indicating lamp for RYB, spring charged, DC supply healthy, ON/OFF, Breaker in Service/Test

8 Window annunciator.

Potential Transformer:

PT, 1 Phase, Resin cast, Draw out type, 11 kV/rt3/110V/rt3, with provision for fuse mounting HT &LT, CL:1.0, 100VA.

Current Transformer:

CT’s, Dual core, 11 kV, Resin cast, CTR:100/50/1A-1A, STC-26.2kA for 1sec) Core 1: Cl- 1.0, 10VA, Core 2: Cl- 5P10, 10VA. OR as required at site (Suitable for 500 KVA + 400 KVA Load).

Meters:

Multi function meter with comm. Port, LED indication for and fault in communication and calibration, sampling rate 64/1s.EM6400NG

Relays:

Digital Numerical Relay for over current and earth fault with Instantaneous protection,TCS,S/C, flush mounting, CT Sec: 1A, 110V DC Aux. Supply with RS-485 Communication Port TYPE: REF-615/Micom P122/7SJ62

Relays:

Master Trip Relay, 110V DC Aux.

Anti pumping Relay, Flush/Base Mounting Type 110V DC Coil with 2NO Aux. Contacts,

Under volt relay

Indicating Lamps:

Indicating lamp, 22.5mm Dia, LED Type.

Push Buttons:

Push buttons, 22.5mm Dia.

Emergency Stop Push Buttons:

Emergency Stop, Red, 22.5mm DIA, LED inbuilt.

Switches:

Breaker Control Switch, 16A, spring Return.

Auxiliary Contactors:

Aux. contactor, 110V DC Coil / 230 V AC Coil with 2NO+2NC Aux. Contacts As required

Auxiliary Relay:

Plug-in Type Aux. Relay, 2C/O, 110V DC Coil / 230 V AC Coil, Base mounting Type or As required

MCB, 10kA, ' C ' Curve or as required

Other Items:

Static Alarm Annunciation, 08 Windows, 110V DC Aux. Supply. With built in Test/Accept/Reset/Mute Pushbutton

Hooter for Faults , 110V DC, 96Sq.mm ( each)

PT Fuses 11KV, 3A

Modular type socket, 3 Pin, 15A

Panel illumination lamp: 230V AC, 5 Watts, LED TYPE

Door Limit Switch, 230V AC,1NO+1NC

Power Pack 110V / 12V DC Supply with battery backup

OUTGOING VCB

Supply, installation, testing and commissioning of VCB as per IEC-62271-100, 11kV, 630A, 3 Pole, 500MVa for 3Sec, Electrically and manually Operated draw out Type, single break, trip free mechanism, auto/manually closing breaker, complete with self contained, fully interlocked, rack in and rack out mechanism, with epoxy encapsulated vacuum bottle, required Aux. Contacts, Limit Switches for Test & Service Position.

Accessories

Spring charging motor : 230V AC , Handle for manual spring charging

Closing coil : 110V DC

Shunt trip coil: 110V DC

Space heater with thermostat

Indicating lamp for RYB, spring charged, DC supply healthy, ON/OFF, Breaker in Service/Test

8 Window annunciator.

Current Transformer:

CT’s, Dual core, 11 kV, Resin cast, CTR:60/30/5A, STC-26.2kA for 1sec) Core 1: Cl- 1.0, 10VA, Core 2: Cl- 5P10, 10VA.or as required at site (Suitable for 500 / 400 KVA Transformer).

Multifunction meter with comm. Port, LED indication for and fault in communication and calibration sampling rate 64/1s.EM6400NG

Meters:

Digital Numerical Relay for over current and earth fault with Instantaneous protection,TCS,S/C, flush mounting, CT Sec: 1A, 110V DC Aux. Supply with RS-485 Communication Port TYPE: REF-615/Micom P122/7SJ62

Master Trip Relay, 110V DC Aux.

Anti pumping Relay, Flush/Base Mounting Type 110V DC Coil with 2NO Aux. Contacts,

Relays:

Comprehensive motor protection relay

Under volt relay

Bucholz protection relay

Indicating Lamps:

Indicating lamp, 22.5mm Dia, LED Type.

Push Buttons:

Push buttons, 22.5mm Dia.

Emergency Stop Push Buttons:

Emergency Stop, Red, 22.5mm DIA, LED inbuilt.

Switches:

Breaker Control Switch, 16A, spring Return.

Auxiliary Contactors:

Aux. contactor, 110V DC Coil / 230 V AC Coil with 2NO+2NC Aux. Contacts As required

Auxiliary Relay:

Plug-in Type Aux. Relay, 2C/O, 110V DC Coil / 230 V AC Coil, Base mounting Type or As required

MCB, 10kA, ' C ' Curve or as required

Static Alarm Annunciation, 08 Windows, 110V DC Aux. Supply. With built in Test/Accept/Reset/Mute Push button

Hooter for Faults , 110V DC, 96Sq.mm

PT Fuses 11KV, 3A

Other Items:

Modular type socket, 3 Pin, 15A

Panel illumination lamp: 230V AC, 5 Watts, LED TYPE

Door Limit Switch, 230V AC,1NO+1NC

VCB Panel with 1No. 630A VCB (1 Incomer) and 2Nos. 630A VCBs (Outgoings) with CTs

TRANSFORMER

Design, Engineering, Manufacturing, Testing at Manufacturers place and Supply of 11/0.433KV 400KVA Level-3 50 Hz Off Load Tap Changer, Three phase, Oil type transformer. (CMKL / Sudhir / Schenider make)

i) Standard: IS : 2026 and IS 1180 (Part - 1) Level 3 BEE Star 2 with all latest amendments ii) Losses at 50% loading: 1150 Watts (Max) iia) Losses at 100% loading: 3330 Watts (Max) iii) Outdoor / Indoor Installation, iv) Vector group : Dyn11 v) Rating : 400 KVA vi) Cooling System: ONAN, vii) Winding: Copper, viii) Magnetic Core: Prime grade of M4 or better ix) High voltage : 11KV - 50 Z, x) Low voltage: 433V-50HZ xi) System highest voltage : 12kV at the HV side xii) Manufacturer testing labotatory to be NABL certified with in house core cutting facility for proper control & monitoring of quality & to avoid mixing of Prime core with Second grade /defective core materials xiii) Insulation Level - H.V. Power Frequency (KV rms): 28 kV - H.V. Impulse withstand voltage (KV peak): 75 kVp Tapping: +5% to -10% off load tap links in steps of 2.5%. Temperature rise of Oil/Winding Over design ambient temperature of 50 deg C: 40/45 deg. C

Supply and erection Silent Genset (Kirloskar / Sudhir / Cummins / Mahindra make) suitable for 415V 3phase A/C supply complete

250KVA SILENT D.G. SET WITH STANDARD CONTROL PANEL (HSN CODE8502)

“KIRLOSKAR" (brand KOEL Green) Make diesel engine Model 6SL1500TA-G3, 6 cylinders, liquid cooled, turbocharged with after cooler, developing 310BHP @ 1500 RPM. This engine is a inline type, 4 valve per cylinder, electric start, compression ignition, 4 stroke engine designed to run continuously at 1500 RPM confirming to rime rating ISO-3046 standard with an overload capacity of 10 % for one hour in every 12 hrs of operation. Diesel Engine conforms to present CPCB norms. The diesel engine will comprise of following:-

✓ Flywheel with Starter Ring for Generating Set.

✓ Air filter.

✓ Lube oil cooler assembly with accessories.

✓ Exhaust air manifold.

✓ Exhaust Silencer.

✓ Expansion bellow.

✓ Fuel filter.

✓ Lube oil filter.

✓ Exhaust gas Turbocharger with after cooler.

✓ Radiator with pusher type fan, with fan guard, coolant pump.

✓ 24V (2x12V) electrical starting system with starter motor & battery charging alternator

✓ In‐line Monoblock Fuel Injection Pump with Electronic Governing & Isochronous capability

✓ Bore x Stroke – 118 x 135 mm.

✓ Engine Cubic Capacity - 8.86 litres

✓ Engine mounting supports.

✓ Engine control panel – Microprocessor based Controller Model 745.

✓ Engine Safeties, Alarms and Trips (Details in Controller specifications)

✓ K Cool super plus corrosion inhibitor coolant for cooling.

✓ Engine Operator/Maintenance & Spare parts CD

✓ Engine Warranty Certificate.

✓ Engine test certificate

ALTERNATOR:

KOEL GREEN make rated at 250 KVA, 415 Volts, 3 Phase, 4 wire, 0.8 p.f. (lag), 50Hz, 1500RPM, in accordance with IS-4722 as per following specifications:

✓ Type: Salient poles, Single bearing, Brushless type, suitable for direct coupling to engine.

✓ Rating: Guaranteed to deliver required output at the ambient temperature conditions. Suitable for an over‐load of 10% for 1 hour in every 12 hours of operation.

✓ Voltage Regulation: Provided with fast response thyristor type electronic automatic voltage regulator, which holds output voltage within desired limits. (+/‐ 1%).

✓ Excitation: Self excited‐self regulated.

✓ Alternator Loading: Suitable for taking rated load immediately after machine reaches rated voltage and speed.

✓ Equipped with AREP (Auxiliary regulation Exciting Principle) winding to give performance equivalent to PMG as standard scope of supply

✓ Vibration: Suitable for direct coupling with Engine and mounted on common fabricated sheet metal base frame.

✓ Enclosure: Screen protected drip proof enclosure with IP – 23 degree of protection.

✓ Cooling: Air Cooled type with radial fan mounted on Rotor.

✓ Winding and Insulation: Insulation class H as defined in IS – 4722.

ESSENTIAL ACCESSORIES :

One Following set of essential accessories are supplied with each DG set.

✓ One No. MS Base Frame suitable for mounting of the offered engine and alternator.

✓ One No. fuel tank of standard capacity 460 litres complete fuel gauge, inlet/outlet connections, drains plug, etc.

✓ Two No. 12 Volts DC Battery of suitable capacity with leads.

✓ 1 Set of AVM Pads fitted in Base Frame.

✓ All above accessories are housed in acoustic enclosure.

STANDARD CONTROL PANEL :

The Control Panel body will be fabricated out of 16 SWG MS sheet. Panel will be suitable for inside Canopy mounting, Indoor Installation, Copper Control cable of suitable size is used. Cables are ferruled for proper maintenance/checking/wiring of panel. Detachable cable gland plates are provided. The panel will be equipped as follows:

✓ One No. Moulded Case Circuit Breaker of suitable capacity.

✓ Aluminium Bus Bars of suitable capacity provided with termination.

✓ 3 Nos. Current Transformers of suitable ratio.

✓ One set of instrument MCB’S.

✓ Microprocessor based controller KG745 controlling various Mechanical & Electrical protections with display and indications of Electrical and Mechanical Parameters are as follows.

✓ Kirloskar Remote Monitoring (KRM)

KIRLOSKAR REMOTE MONITORING (KRM) :

The KRM system links your Genset with central monitoring data server through a SIM and internet. The complete health monitoring panel with all critical indications can be viewed on your laptop screen or mobile app. The features of KRM are:

✓ Quick look dashboard to give you glimpse of your Genset health

✓ Business Intelligence page which gives you comprehensive insight of your Genset health and performance.

✓ Graphical reports of critical genset parameters for detailed analysis.

This close monitoring also helps in reducing operating costs and enhancing reliability of Genset. So in all one can have better return on your investment and enhanced productivity.

500KVA KOEL GREEN SILENT D.G. SET WITH STANDARD CONTROL PANEL (HSN CODE8502)

“KIRLOSKAR" (brand KOEL Green) Make diesel engine Model DV10TA G1, 10 cylinders, liquid cooled, turbocharged with after cooler, developing 608BHP @ 1500 RPM. This engine is a V type, 4 valve per cylinder, electric start, compression ignition, 4 stroke engine designed to run continuously at 1500 RPM confirming to rime rating ISO-3046 standard with an overload capacity of 10 % for one hour in every 12 hrs of operation. Diesel Engine conforms to present CPCB norms. The diesel engine will comprise of following: -

✓ Flywheel with Starter Ring for Generating Set.

✓ Air filter.

✓ Lube oil cooler assembly with accessories.

✓ Exhaust air manifold.

✓ Exhaust Silencer.

✓ Expansion bellow.

✓ Fuel filter.

✓ Lube oil filter.

✓ Exhaust gas Turbocharger with after cooler.

✓ Radiator with pusher type fan, with fan guard, coolant pump.

✓ 24 V (2 x 12 V) electrical starting system with starter motor and battery charging alternator

✓ In‐line mono block Fuel Injection Pump with Electronic Governing & Isochronous capability

✓ Bore x Stroke – 130 x 150 mm.

✓ Engine Cubic Capacity - 19.90 litres

✓ Engine mounting supports.

✓ Engine control panel – Microprocessor based Controller Model 745.

✓ Engine Safeties, Alarms and Trips (Details in Controller specifications)

✓ K Cool super plus corrosion inhibitor coolant for cooling.

✓ Engine Operator/Maintenance & Spare parts CD

✓ Engine Warranty Certificate.

✓ Engine test certificate

ALTERNATOR:

KOEL GREEN make rated at 500 KVA, 415 Volts, 3 Phase, 4 wire, 0.8 p.f. (lag), 50Hz, 1500RPM, in accordance with IS 4722 as per following specifications:

✓ Type: Salient poles, Single bearing, Brushless type, suitable for direct coupling to engine.

✓ Rating: Guaranteed to deliver required output at the ambient temperature conditions. Suitable for an over‐load of 10% for 1 hour in every 12 hour of operation.

✓ Voltage Regulation: Provided with fast response thyristor type electronic automatic voltage regulator, which holds output voltage within desired limits. (+/‐ 1%).

✓ Excitation: Self excited‐self regulated.

✓ Alternator Loading: Suitable for taking rated load immediately after machine reaches rated voltage and speed.

✓ Equipped with AREP (Auxiliary regulation Exciting Principle) winding to give performance equivalent to PMG as standard scope of supply

✓ Vibration: Suitable for direct coupling with Engine and mounted on common fabricated sheet metal base frame.

✓ Enclosure: Screen protected drip proof enclosure with IP – 23 degree of protection.

✓ Cooling: Air Cooled type with radial fan mounted on Rotor.

✓ Winding and Insulation: Insulation class H as defined in IS – 4722.

ESSENTIAL ACCESSORIES :

One Following set of essential accessories are supplied with each DG set.

✓ One No. MS Base Frame suitable for mounting of the offered engine and alternator.

✓ One No. fuel tank of standard capacity 990 litres complete fuel gauge, inlet/outlet connections, drains plug, etc.

✓ Two No. 12 Volts DC Battery of suitable capacity with leads.

✓ 1 Set of AVM Pads fitted in Base Frame.

✓ All above accessories are housed in acoustic enclosure.

STANDARD CONTROL PANEL :

The Control Panel body will be fabricated out of 16 SWG MS sheet. Panel will be suitable for inside Canopy mounting, Indoor Installation, Copper Control cable of suitable size is used. Cables are ferruled for proper maintenance/checking/wiring of panel. Detachable cable gland plates are provided. The panel will be equipped as follows:

✓ One No. Moulded Case Circuit Breaker of suitable capacity.

✓ Aluminium Bus Bars of suitable capacity provided with termination.

✓ 3 Nos. Current Transformers of suitable ratio.

✓ One set of instrument MCB’S.

✓ Microprocessor based controller KG745 controlling various Mechanical & Electrical protections with display and indications of Electrical and Mechanical Parameters are as follows.

✓ Kirloskar Remote Monitoring (KRM)

KIRLOSKAR REMOTE MONITORING (KRM) :

The KRM system links your Genset with central monitoring data server through a SIM and internet. The complete health monitoring panel with all critical indications can be viewed on your laptop screen or mobile app. The features of KRM are :

✓ Quick look dashboard to give you glimpse of your Genset health

✓ Business Intelligence page which gives you comprehensive insight of your Genset health and performance.

✓ Graphical reports of critical genset parameters for detailed analysis.

This close monitoring also helps in reducing operating costs and enhancing reliability of Genset. So in all one can have better return on your investment and enhanced productivity.

Main PCC Panel

Supply, fabrication and carriage of cubical type panel compartmentalized fabricated out of 14G CRCA sheet with internal member of 16G complete with erection of incoming and outgoing switchgear, supply and erection of busbars meters, indicators, cable end boxes as required. The panel should be as per 3B construction. The panel shall be either floor standing type or wall mounted as per drawing and site. The panel shall be totally enclosed dust and vermin proof construction with square sections rubber gaskets. The floor mounted panels shall be strictly as per specifications. The busbar will be wrought aluminium E91E grade suitable for 50KA fault level for one second (The fabricator will have to give manufacturer's certificate of E91E grade wrought aluminium busbar). All four busbars should be insulated with colour should PVC heat shrinkable sleeves. The panel should be complete as per the drawing and includes all internal wiring with PVC copper cable of requisite size complete with name plates of each feeder, danger plate, solid bus connections, cable alleys, busbar chamber etc.

including cost of LT CT electronic three phase Multifunctional Meter with their CTs and all connections. and other petty material The panel will be powder coated after chemical treatment. The degree of protection panel should be IP54 and should be extendable on both sides. All MCCBs shall be Ics = 100% Icu and are to be provided with extended rotary handles, spreaders and Phase Barriers for proper termination of cables. All MCBs are to be 'C' series. The Panel should be fabricated from CTRI approved Panel Builder. The names are International Switchgear / Tricolite / Advance Switchgear / Unitech / Vrindavan Electricals make.

INCOMER

800A, EDO 4P 50 KA ACB with Microprosser Based O/L,S/C & E/F Release with 1No. Multifunction Meter, 3 sets of Indication Lamp R-Y-B, Indication Lamp On-Off-Trip, Control MCB 20/2A SP.10KA.’C’ Curve, Control MCB 6A SP.10KA.’C’ Curve, CTs 800/5A For Metering, 1No. each of CTs 800/5A For APFCR, Under Voltage Trip Coil, Shunt Trip Coil, Auxilary Contacts, E.Mechanical Interlocking, Auxilary Contactor, Breaker Control Switch, Exhaust Fan 15" + Filter, 4 Nos. each CT Shorting Link and Control Terminals and 1No. of Neutral Link = 2 Nos. for Transformer-1 (500 KVA) and Transformer-2 (400 KVA) Incomers.

800A, EDO 50KA 4P ACB with Microprosser Based O/L, S/C & E/F Release with 1No. Multifunction Meter, 3 sets of Indication Lamp R-Y-B, Indication Lamp On-Off-Trip, Control MCB 20/2A SP.10KA.’C’ Curve, Control MCB 6A SP.10KA.’C’ Curve, 4 Nos. each CTs 800/5A For Metering + Protection Relay, CT Shorting Link, Control Terminals, 1 No. each Under Voltage Trip Coil, Shunt Trip Coil, Auxilary Contacts, Electrical-Mechanical Interlocking, Auxilary Contactor Breaker Control Switch, Exhaust Fan 15" + Filter, Reverse Power Relay, Neutral Link = 1 No. for 500 KVA DG-3 Incomer.

800A, EDO 50KA 4P ACB with Microprosser Based O/L, S/C & E/F Release with 1No. Multifunction Meter, 3 sets of Indication Lamp R-Y-B, Indication Lamp On-Off-Trip, Control MCB 20/2A SP.10KA.’C’ Curve, Control MCB 6A SP.10KA.’C’ Curve, 4Nos. each CTs 630/5A For Metering + Protection Relay, CT Shorting Link, Control Terminals, 1No. each Under Voltage Trip Coil, Shunt Trip Coil, Auxilary Contacts, E-Mechanical Interlocking, Auxilary Contactor, Reverse Power Relay, Neutral Link = 1 No. for 250 KVA DG-2 Incomer.

400A 4P 50 KA Motorised MCCB with Adjustable M/P Based Release having O/L,S/C & E/Fprotections, ROM & Spreader Link with 1No. Multifunction Meter, 3 sets of Indication Lamp R-Y-B, Indication Lamp On-Off-Trip, Control MCB 20/2A SP.10KA.’C’ Curve, Control MCB 6A SP.10KA ‘C’ Curve, 4Nos. each CTs 250/5A For Metering + Protection Relay, CT Shorting Link, Control Terminals, 1No. each Under Voltage, Trip Coil, Shunt Trip Coil, Auxilary Contacts, E.Mechanical Interlocking, Auxilary Contactor, Reverse Power Relay, Neutral Link = 1 No. for 125 KVA DG-3 Incomer.

3 Sets of DG Sync. Relay, Battery Charger & Control Gear etc.

800A, EDO 4P 50 KA ACB with Microprosser Based O/L,S/C & E/F Release with Indication Lamp On-Off, Control MCB 6A SP. 10KA.'C' Curve, Under Voltage Trip Coil, Shunt Trip Coil Auxilary Contacts, E.Mechanical Interlocking, Auxilary Contactor, Breaker Control Switch, Control Terminals, Neutral Link = 1 No. for Bus Coupler-1.

400A 4P 36KA Motorised MCCB with Adjustable M/P Based Release having O/L,S/C,protections, ROM & Spreader Link with Indication Lamp On-Off, Control MCB 6A, SP. 10KA "C" Curve, Under Voltage Trip Coil, Shunt Trip Coil, Auxilary Contacts, E.Mechanical Interlocking, Auxilary Contactor, Control Terminals, Neutral Link = 1 No. for Bus Coupler-2.

Aluminium Bus Bar 1000A having cross section 1X100X12 mm for Phase & 1X100X6 mm for Neutral & Current carring capacity 1.6A/Sq. mm2.

S/E of Programmable Logic System: For Electrical Interlocking, Auto Load Sharing and Synchronisation of all three DGs (1Nos. each 500KVA, 250KVA, &.125KVA having features of switching on all the three DGs in parallel duly synchronised in case of failure of electric supply and feature of auto load sharing as per the requirement of load. They should be able to run independently with bus coupler open in case of failure of synchronisation. The job includes Programmable Logic Controller (PLC) + Power Supply + Other Required accessories + Programming, Installation, Testing and Commissioning of PLC.

OUTGOING

400A 4P 36KA MCCB with Adjustable M/P Based Release having O/L,S/C,protections, ROM & Spreader Link with Indication Lamp On-Off, Auxilary Contacts, Control MCB 6A SP.10KA ’C’ Curve, Neutral Link = 3Nos.

250A 4P 36KA MCCB with Adjustable M/P Based Release having O/L,S/C,protections, ROM & Spreader Link with Indication Lamp On-Off, Auxilary Contacts, Control MCB 6A, SP 10KA ‘C’ Curve, Neutral Link = 1No.

200A 4P 36KA MCCB with Adjustable M/P Based Release having O/L,S/C,protections, ROM & Spreader Link with Indication Lamp On-Off, Auxilary Contacts, Control MCB 6A, SP 10KA ‘C’ Curve, Neutral Link = 1No.

100A 4P 36KA MCCB with Adjustable M/P Based Release having O/L,S/C,protections, ROM & Spreader Link with Indication Lamp On-Off, Auxilary Contacts, Control MCB 6A, SP 10KA ‘C’ Curve, Neutral Link = 5Nos.

630A 4P 36KA MCCB with Adjustable M/P Based Release having O/L,S/C,protections, ROM & Spreader Link with Indication Lamp On-Off, Auxilary Contacts, Control MCB 6A, SP 10KA ‘C’ Curve, Neutral Link = 1No.

200A 4P 36KA MCCB with Adjustable M/P Based Release having O/L,S/C,protections, ROM & Spreader Link with Indication Lamp On-Off, Auxilary Contacts, Control MCB 6A, SP 10KA ‘C’ Curve, Neutral Link = 1No.

100A 4P 36KA MCCB with Adjustable M/P Based Release having O/L,S/C,protections, ROM & Spreader Link with Indication Lamp On-Off, Auxilary Contacts, Control MCB 6A, SP 10KA ‘C’ Curve, Neutral Link = 2Nos.

63A 4P 25KA MCCB with Adjustable T/M Based Release having O/L, S/C, protections, ROM & Spreader Link with Indication Lamp On-Off, Auxilary Contacts, Control MCB 6A SP 10KA ‘C’ Curve, Neutral Link = 2Nos.

DUMMY SPACE FOR 400A 4P 36KA MCCB with Adjustable M/P Based Release = 1No.

40kVAR CAPACITOR

Incomer

Outgoings

20kvar Capactior Feeder = 1No.

10kvar Capactior Feeder = 1No.

5kvar Capactior Feeder = 2Nos.

Supply and erection of Sand bucket stand made out of 50mm x 50mm x 5mm angle iron frame having 3 Nos. MS Buckets of 9ltr capacity duly painted with red paint after red oxide primer and filled with sand. The stand is to be grounted in the ground with its legs at least 1' under the ground covered with cement, concrete. The job includes cost of all abovesaid materials and labour.

Supply and laying on non skid rubber mat 12mm thick ISI marked of required length suitable for 11 KV supply (HT). Complete in all respect as desired by the Engineer in charge. ISI marked.

Supply and erection of wall mounted First Aid Kit Box (Min Size of box 320 x 280 x 80 mm) made from High Grade Metal with processed powder coating for Anti Rust proof long life having 3 shelves with Acrelic glass shutter with security lock , handle etc complete.

Pdg. And fixing 50mm x 5mm GI strip on surface or in recess for connection etc. as required with all labour and material.

Supply and erection of PVC unsheathed copper conductor cable single core 1100V grade Size 70 Sqmm in pipe of suitable size excluding cost and erection of pipe. (Finolex / Havell's / RR cables / Polycab / KEI make only) (For DG 500 KVA)

Supply, fabrication and erection of channel bracket made out of 75x40x40mm ISMC channel 1.5m long suitable for 3Nos. 120W-150W LED flood lights. In the centre of bracket a GI pipe 80mm dia 'B' class 45cm long is to be welded. 2Nos. MS strip supports of size 50x6mm are to be welded diagonally with pipe and channel for mechanical strength. The bracket is to be painted with primer and spray painted. The bracket is to be fixed on existing 8m high pole by slipping the 80mm dia pipe on pole top and fixing with 2Nos. Nut-bolts of 12mm dia for proper grip of bracket with pole. The job includes cost of all abovesaid material.

Supply, carriage and erection of 70W-72W LED 6000K, die-cast aluminium street light luminaire with efficacy of minimum 110 lm/W with LED life of 50000 br hrs complete with toughned glass and other material required to complete the job in all respect. he Fixture supplied with Electronic high efficiecy driver having Power factor >0.9, THD <10%. The job includes the cost of install the fitting on the existing bracket on 7m high pole complete the job in all respect including making connection from light point to fitting. The fitting should be of make Bajaj Make BRTFG 72W LED V3 (72W) IP66 / Wipro Cat No.LR02-781-XXX-57-G2 (70W) IP66 / Philips make BRP409 LED 060 CW HE NR PC S1 PSU GR (70W) IP66 or its equivalent GE / Lux Max or of approved make of department.

S/I/T/C of LED street light light fitting of 36W rating with integral / non-integral driver and minimum 110 lumens per watt complete in all respect. The fitting is to be fixed on wall with bracket mounted on wall. The job includes cost of bracket made of GI pipe 32mm dia B-class 0.3m overhang L-shaped angle of inclination 120 degree with upper side of bracket 300mm and lower side of 400mm long. The bracket is to be fixed on wall with 2Nos. anchor fastners grouted in wall. The job includes cost of LED fitting, GI pipe bracket and anchor fasterners etc. required to complete the same. The work should be completed as per satisfaction of Engineer-in-charge. Wipro Cat No.LR13-501-XXX-57-XX (35W) / Philips make Cat No.BRP046 LED 36 CW MR S1 PSU GR (36W) / Bajaj make Cat.No.BRTFG 36W LED (36W) or as approved in the department)

Supply, carriage and erection of 120W LED Flood light Luminaire (White) with efficacy of minimum 110 lm/W with LED life of 50000 br hrs with THD<10% and PF>0.9 with die cast aluminium bod. Fixture suitable for Outdoor application with IP66 protection.The fixture has colour temperature of 5700K with precise beam angle of 60degree. The job is includes cost of all material and erection of fitting on existing MS channel bracket on 8m high pole with suitable fixing arrangements including connection to the nearest light point with copper wires. The work should be completed as per satisfaction of Engineer-in-charge / Architect. Wipro Cat No. LF20-132-060-57-xx Model Alpha floodlight / Philips make BVP192 LED110 CW HO NB FG GR PSU / Bajaj make BJFL 120W LED I or of approved make of department.

Supply, fabrication and erection of GI pipe (B-class) ISI marked Jindal make street light bracket 1.5" dia 0.9m overhang L shaped with angle of inclination 105 degree and lower side of 80mm GI pipe 0.45m long slipped over the pole fixed with 2 Nos. 12mm dia nut-bolts. The top end of the 80mm GI pipe is to be covered with 2mm thick MS sheet and conical MS sheet 3mm thick is to be welded between 1.5" and 3" GI pipe to give mechanical strength. The job includes cost of all abovesaid material including painting of all MS parts and erection of the same on 8m high octagonal pole with all petty material required.

Single Arm Bracket

Double Arm Bracket

Supply, carriage, erection, testing and commissioning of electronic time switch suitable for 3 Phase system comprising of 1 No. Digital timer clock with battery, 1 No. 63A 3pole Power contactor AC-3 duty and bypass switch enclosed in a readymade MS enclosure complete with all wiring. The work should be completed as per satisfaction of Engineer-in-charge / Architect.

Daily programmable Digital Time Switch timer with 1 No. 3 phase power contactor 63A - 3P complete in all respect. Indo Asian (TL064DB0) or its equivalent L&T / Havell's / Hager / Schneider as approved by the department.

Supply and rection of vertical double door sheet enclosure distribution board (IP 43) suitable for MCCB as incomer recessed in wall including bonding to earth with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in charge of the work.

8 way, TPN (Vertical, Double Door MCCB provision as incomer and provision for 24 Nos. 6A-30A MCB SP as outgoings) Havell's make (Cat No. DHDLVDRWGOFO08) / Schneider make (Cat.No. A9HVTD08) / Legrand Make (Cat.No.5077 47) or as approved in the deparment)

Wiring in 1.5 sqmm PVC insulated copper conductor cable, single core, 1100 volts in 25mm dia PVC pipe, Heavy gauge, ISI mark with modular accessories and GI sheet steel modular boxes of required size with modular inner & outer face plates complete (flushed). (Based on HSR - 31.1). Modular accessories should be either of make (Legrand (Arteor) / Schneider make LIVIA / Havell's Crabtree make Munaro / North-west / MK make or its equivalent as approved by the department).

(i) Fan Point :-

(b) Medium point

(c) Long point

(ii) Light Point single control :-

(a) short point

(b) Medium point

(c) Long point

(v) Light Plug

(a) short point

(vi) Power Plug

(c) Long point

Supply, Carriage, erection, testing and commissioning of LED fitting with integral / non-integral driver. The lumen output of LED should be minimum 100 lumens per watt and should be type tested from Government / NABL / UL accredited laboratory for LM79 & LM80 test reports and copy of same has to be submitted to the client department. The Fixture supplied with Electronic high efficiecy driver having Power factor >0.9, THD <10%. The sample of fitting can be got tested in the presence of representative of the department from NABL I UL accredited laboratory. The job includes cost of all material and erection of fitting with all accessories including anchor fasteners and connection to the nearest light point with copper wires. The work should be completed as per satisfaction of Engineer-in-charge.

Supply, carriage, erection, testing and commissioning of 40W LED High efficiency aluminium profile linear batten with polycarbonate diffuser for enhanced productivity. Ingress protection IP40 (Wipro Make Cat.No.LL24-541-XXX-57-CD / Philips make Cat.No. BN100C LED40S-6500 PSU L120 GR / Bajaj make Cat.No. BLTRU 40W NW VIVA or as approved in the department).

Supply, Erection, Testing & Commissioning of A.C. ceiling fan double ball bearing Energy Saver (5 star rating) complete in all respect without fan regulator. The fan should consume less power.

48" sweep (Ceiling Fan Havell's make ES - 50 Premium or its equivalent of Crompton make Aura Prime Antidust / Orient make Energy Star (White) / Usha make)

S/E of A.C. Exhaust fan (ISI Marked) suitable for single phase A.C. 230 Volts, 50 HZ capacitor, 900 RPM (Heavy Duty) complete with mounting ring frame with four fixing holes and automatic louver shutter but without regulator. The exhaust fan and its louver is to be fixed in the existing glazing with suitable MS frame of required thickness as per site including its painting etc. as per site requirement.

Size 380mm sweep (Havell's make Turbo Force 900rpm single phase or its equivalent of Crompton make EXHD380-6-1 / Orient make (Grey) / Usha make)

DSR Items

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

150mm dia (DSR Item 14.14.2) (598-20%)

Bidder Name

Amount

HITECH ERECTORS PVT. LTD.(GSTN-07AAACH0859B1Z0)

Ecs Engineering Chd. Pvt. Ltd.(GSTN-04AAEFE5310P2ZH)

Highlight Associates and Contractors(GSTN-06AAKFH2063G1ZK)

saggi electrical(GSTN-NA)

Ecs Engineering Chd. Pvt. Ltd.

HITECH ERECTORS PVT. LTD.

Highlight Associates and Contractors

Highlight Associates and Contractors

Ecs Engineering Chd. Pvt. Ltd.

HITECH ERECTORS PVT. LTD.