Repair / maintenance of street light fittings and connected items in KLP / ILP location under GE (Army) Suratgarh at Suratgarh Mil Stn

Amount

Disconnecting and re-stretching ACSR conductor of any size and re-fixing with and including new 2mm dia aluminum binding wire complete all as specified. Notes :- (i) The rate quoted by the contractor shall deemed to be included for cutting / trimming of tree branches touching / approaching the LT over lines upto 3 metre width on each side with hacksaw / axe to clear the LT line including disposal of trimmed branches 100 metre away inside the cantonment area & cleaning site as directed by Engineer-in-charge. (ii) Length of each conductor shall be measured as one length.

Inspection/Checking of street light fitting such as HPSV lamp fitting 70/150/250 watts, Energy saving light fitting 4x24/2x36/1x36 watt and high mast light / SV / MV / MH light fittings 250/440 watts and 45/60/72/90 watt LED light fittings etc for tighting the connection with replacement of twin core multi stranded 4 sqmm aluminium wire complete all as specified and directed by Engineer-in-Charge. Notes :- (i) Ladder wheel shall be arranged by the Contractor. (ii) The cost of wire replaced will not be paid seprately in over head conductors only.

Taking down street light fitting such as HPSV lamp fitting 70/150/250/400 watts, Energy saving light fitting 4x24/2x36/1x36 watt and high mast light / SV / MV / MH light fittings 250/440 watts and 45/60/72/90 watt LED light fittings etc for finding faults including cleaning of acrylic Perspex cover with castic soda solution and refixing the same in existing position after carrying out necessary repair / replacement of unserviceable parts complete all as specified and directed by Engineer-in-Charge. Notes :- (i) The accessories / spare parts which are required to be replaced shall be measured and paid for separately as “Supply only” under srl item No 4 to 9 of BOQ here-in-after. (ii) Ladder wheel shall be arranged by the Contractor. (iii) Detection and rectification of fault in over head/under ground line shall be done by the contractor.

Supply only T-5 Tube rod 1x24 watts complete all as specified and directed by Engineer-in-charge. Make :- Wipro / Philips / Syska / Crompton

Supply only electronic ballast 1x24 watt, 240 Volts suitable for fluoroscent light fittings complete all as specified and directed by Engineer-in-charge. Make :- Wipro / Philips / Syska / Crompton / Surya

Supply only electronic driver 220/240 volts suitable for existing LED Street light fitting 45 watts complete all as specified and directed by Engineer-in-Charge. Make :- Wipro / Philips / Syska / Crompton / Surya

Supply only electronic driver 220/240 volts suitable for existing LED Street light fitting 60 watts complete all as specified and directed by Engineer-in-Charge. Make :- Wipro / Philips / Syska / Crompton / Surya

Supply only electronic driver 220/240 volts suitable for existing LED Street light fitting 72 watts complete all as specified and directed by Engineer-in-Charge. Make :- Wipro / Philips / Syska / Crompton / Surya

Supply only electronic driver 220/240 volts suitable for existing LED Street light fitting 90 watts complete all as specified and directed by Engineer-in-Charge. Make :- Wipro / Philips / Syska / Crompton / Surya

S&F in replacement 10 KV surge protector suitable for LED fittings 45 / 60 / 72 / 90 watts complete all as specified and directed by Engineer-in-Charge. Make :- Crompton Cat part No SRPSQ-10KV/5KA-440 or equivalent in Crompton / Syska / Havells / Polycab

S&F in replacement weather proof PVC insulated, sheathed three core stranded aluminium conductor cable of size 2.5 Sqmm, 1100 Volts grade conforming to IS:9968 (Part-I) 1988 or IS:694-1990 complete all as specified and directed by Engineer-in-Charge.

Disconecting and taking down existing unservicable unserviceable street light fittings of any type and make along with accessories as directed by Engineer-in-charge. Notes:- (i) Any T & P and Ladder wheel required for the work shall be arranged by the Contractor. The rate of this aspect is included in this item and nothing extra shall be paid on this account.

S&F in replacement LED flood light of 150 watt with high pressure die cast housing with lens with lument output 6000K complete (including LED, drive and internally prewired) with on board 5 KV surge protection with 10 KV external SPD. The luminaries shall be monolithic construction totally enclosed dust and water proof with minimum IP 65 protection as per IS 10322-1982 (part-I) with latest amanedments and input voltage range 140-300V AC, frequency 50-60 Hz, P.F should be more than 0.9. The efficiency of LED luminaries system shall be more than 100 lumens per watt and FRLSH cable PVC insulated stranded copper conductor, 1100 volts grade, 2.5 sqmm x 3 core of ISI marked for light to ceiling rose complete including arrangement of mounting for street light as required at site complete all as specified and directed by Engineer-in-charge. Make :- Crompton Cat part No LFLN-150-CDL/60-M / Wipro cat part No LF07-152-090-50-V5 / Philips cat part No BVP122 LED 150 CW HE NB FG XTFCL S4

S&F in replacement street light pole box of size not less then 300x200x105mm, made of high quality thermo plastic polystyrene, weather proof, dust, jet water proof, chemical, acid corrosion, impact, insulated & shock proof IP 65 for outdoor Installation with internallly embedded gasket (PUR) including MCB SP 6 Amps 01 No along with left side hinge door (notch arrangement not acceptable) & premoulded knockout all sides including back of the base must. The box fitted with 10 sqmm stud type terminal - 04 Nos including Elimex stud type TB 4 Nos. Make :- Syntex / Hensal / Schneider Notes :- (i) Cost of flat iron clamp is deemed to included in unit rate of this items. Nothing extra shall be paid on this account. (ii) Size of junction box for different mafufacturer may slightly varried from size mentioned in description of item. Contractor has to provide junction box as per cat No mentioned against make of junction box. where cat No is not mentioned against any make, in that case junction box of size mentioned in description has to provide, if exact size of junction box is not available, then next higher size junction box has to be provided. Nothing extra shall be paid on this account.

M&L for painting on steel tubular poles 9 metre long including attachments (cross arms, clamps GI pipes etc) complete with one coat of aluminium paint after preparation of steel surfaces and black & yellow strips 30cm each upto 1.5 metre height from top of PCC foundation block or PCC coping including numbering of poles with synthetic enamel paint (Black) in 80mm high letters over 150mmx230mm yellow base complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old painted surfaces of PCC pole and applying two coats of synthetic enamel paint in black and yellow colour in alternate strips of 30 cm each upto 1.50 metre height from top of PCC coping and applying two coat of aluminum paint over cross arms, brackets, bracings, clamps, hooks etc. and marking pole number with white synthetic enamel paint in 80mm high letters, over black synthetic enamel paint base of size 20cm x 20cm including applying two coats of white wash to coping of poles all as specified and directed by Engineer-in-Charge. Note :- Pole number shall be marked with white enamel paint over a base of size 20cm x 20cm prepared with two coats of black enamel paint on pole surfaces.

S&F in repair street light bracket made out of 32mm dia GI pipe light grade 1.5m long , bent to shape at 120 degree angle from vertical fixed along pole with and including required number of clamp made out of Flat iron 25mm x 6mm with nuts, bolts ,washers etc. duly painted with two coats of aluminium paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-charge.

Supply, fixing and testing LED Street / Security light fitting of 30 Watt, 5700K - 6500 K (including LED drive and internally prewired) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. The luminaries shall be monolithic construction totally enclosed dust and water proof with IP -65 / 66 protection as per IS - 10322-1982(Part -I) with latest amendments and input voltage range 140 - 300 V, AC, frequency 50 - 60 Hz ,P.F should be more than 0.9 with Total Harmonic Distortion THD(I) less than 15% ,cool white colour and lamp starting time should not be more than 10 second including 10 KV surge protection in built or external. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300 V, AC. Driver should also have double phase protection, no load , open circuit and short circuit protection .LED light fitting should be suitable for ambient temperature from -10 degree Centigrade to 50 degree Centigrade and humidity level 10% to 90 % RH. Covers should be polycarbonate/toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficiency of LED luminaries system shall be more than 100 lumens per watt and must be certified by the LM-79 test report and including connection for street light from pole box with 1.5 Sqmm, 3 core PVC insulated stranded copper conductor FRLSH cable, 1100 Volts grade ISI marked including addition / alteration in bracket (if required) for fixing light fitting complete all as specified and directed by Engineer-in- charge. Make :- Crompton Cat Part No LSTS-30-CDL-M / Havells Cat part No ENDURACITYLITEPLATPLUSSL30WLED757SASY BOPC / Wipro Cat Part No LR02-331-XXX-57-XX / Philips

All as per Srl item No 18 above but LED street / security light of 45 watt. Make :- Syska Cat part No. SSK-SLF-F-45W-WL / Crompton Cat Part No LSTV-45-CDL / Havells Cat part No ENDURAPEARL NEOSL45WLED757SASYTOPC / Wipro Cat Part No LR02-501-XXX-57-XX or equivalent in philips

All as per Srl item No 18 above but LED street / security light of 60 watt Make :- Syska Cat part No. SSK-SLF-F-60W-WL / Crompton Cat Part No LSTP-60-CDL-M / Havells Cat part No. ENDURAPEARLNEOSL60WLED757PASY TOPC / Wipro cat part No LR02-671-XXX-57-G2 or equivalent in philips

Notes for srl Item No 18 to 20 :- (a) Tenderer shall submit test report of LED street light fitting from Government accredited test laboratory for LM - 79 and LM - 80 . (b) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of CA. Contractor shall obtain warranty from the manufacturer of product on their letter head and submit the same to deparment alonwith his letter head. The product will be replaced free of cost in the following case :- (i) Manfacturing defects (ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (c) All LED light/luminare must meet the provision laid down in IS - 16101 , 16102 Part -I/II ,16103 Part -I , 16104 ,16105 ,16106 , 16108/2012 and 15885 Part -II / Section 13. (d) Scope of work shall include supply and fixing street light fittings on street light bracket fixed on poles, If street light fitting requires to fixed on existing street light bracket and any addition alterration required in bracket for fixing street light, In that case cost of additional / alteration is included in the unit rate of this item, which also includes needful T & P and required accessories such as 1.5 sqmm, 3 core PVC insulated stranded copper conductor cable for connection from pole box to light fitting etc complete including making connection, testing etc complete .No extra payment is admissible on this account. (e) Light fittings shall be provided with 10 KV surge protection as mentioned in description of item. If 10 KV surge protection is not provided in light fitting for which cat part is mentioned in BOQ. Contractor has to provide light fitting with 10 KV surge protection without any extra cost to department. (f) Contractor shall write CA No on street light fitting with synthetic enamel paint which should be visible from ground level. Cost of the same is included in the unit rate of this item nothing shall be extra paid on this account.

S&F in replacement Single phase automatic automatic street light switch suitable for 3 KW load complete with Infrared sensor based NATURE SWITCH for automatic switching of street / security lights with one number two pole power contractors 40 Amps (Type - MU40-2P, Cs90119) with coil voltage 220 / 240 V and incoming MCBs single pole - 01 No, outgoing MCBs single pole - 01 No of rating 32 Amps & circuit wiring with single core multi stranded of size 10 Sqmm. Lighting switch operation should be based on natural light lux level. Required illuminance level for switching ON is < 30 Lux and for switching OFF > 10 Lux. The sensor (one service & one stand by) should also have part night operation facility for 4,5,6,........11 & 12 hours. The sensor along with suitable power contactor (S), Incoming -outgoing MCB's should be enclosed in a pole / wall mountable enclosure made of Rust proof, Electric shock proof, termite proof and FR grade confirming to IP66 complete all as specified and directed by Engineer in charge. Make :- KAKATIYA ENERGY SYSTEM PVT LTD (Swadeep 02EC3KW1P) / Siemens / Legrand / Indo Asian

S&F in replacement three phase automatic street light switch suitable for 5 KW load complete with Infrared sensor based NATURE SWITCH for automatic switching of street / security lights with three number two pole power contractors 40 Amps (Type - MU40-2P, Cs90119) with coil voltage 220 / 240 V and incoming MCBs single pole - 03 Nos, outgoing MCBs single pole - 03 Nos of rating 32 Amps & circuit wiring with single core multi stranded of size 10 Sqmm. Lighting switch operation should be based on natural light lux level. Required illuminance level for switching ON is < 30 Lux and for switching OFF > 10 Lux. The sensor should also have part night operation facility for 4,5,6,........11 & 12 hours. The sensor along with suitable power contactor (S), Incoming -outgoing MCB's should be enclosed in a Rust proof, electric shock proof, termite proof and FR grade thermoplastic polycarbonate enclosure with hinged lid confirming to IP66 protection class 2. The circuit should also have provision for manual operation (i.e. sensor By-pass option). The enclosure should be platform mounted and structure must be grouted in PCC (1:2:4) type B-1 using 20mm graded stone aggregate blocks of size 30cm x 30cm x 60cm complete all as specified and directed by Engineer in charge. Make :- KAKATIYA ENERGY SYSTEM PVT LTD (Swadeep 02EC3KW1P) / Siemens / Legrand / Indo Asian

Supplying, laying, jointing, commissioning and testing in replacement XLPE insulated screened PVC bedded, armoured, heavy duty underground electric cable with stranded aluminium conductor 1100 volts grade of cross sectional area 25 sq mm 3.5 core confirming to IS-7098 (Part-I-1988) laid in trenches, along poles through pipes etc complete all as specified and directed by Engineer-in-charge. Notes :- (i) Excavation, earth work, sand cushioning, cable protection and GI pipe shall be measured & paid for separately under respective items of BOQ (ii) Road cutting / floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall deemed to be inclusive of the above provisions.

All as per item No 23 above but cable of cross sectional area 16 sq mm 4 core

All as per item No 23 above but cable of cross sectional area 10 sq mm 4 core

All as per item No 23 above but cable of cross sectional area 10 sq mm 2 core

Excavation in trenches, not exc 1.5 m wide and n. exc 1.5 m depth, or n exc 10 Sqm on plan and n exc 1.5 m in depth for foundations of poles, struts, stays etc. or laying underground cable and water supply / sewage pipe line etc. in soft / loose soil & getting out including taking out old brick or precast cable cover complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified and directed by Engineer-in-charge.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and directed by Engineer-in-charge.

M&L for dry sand (Tibba sand) and punning for cushioning to underground cable complete all as specified and directed by Engineer-in-charge Note: - For payment purpose thickness after punning shall be measured.

M & L for brick protection with old size sub class 'B' bricks laid flat, length of bricks across the route of underground cable all as specified and directed by Engineer-in-Charge.

S&F in replacement Galvanized iron tubing, 40mm bore light grade, ISI marked, including all fittings and laid in trenches / under road / drains, fixed to poles / walls with required numbers of clamps made out of 25x3mm flat iron, bolts, nuts and washers for protection of LT electric cable complete all as specified and as directed by Engineer-in-charge. Notes :- (i) Excavation & earthwork shall be measured & paid for separately under respective items of BOQ (ii) Cost of flat iron clamp if required is included in the unit rate of this item. Nothing extra shall be paid on this account.

S&F in replacement power contactor two pole of capacity 40 Amps, suitable for MU-2P with 220/240V, wide band coil complete all as specified and directed by Engineer-in-Charge. Make:- Legrand cat part No 416280 or equivalent in Havells / GE / L&T / Siemens

S&F in replacement LED garden light 15 watt decorative New generation, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source and IP 65 protection with all accesories complete all as specified and directed by Engineer-in-Charge. Make :- Havells cat part No CORALMINIPT15WLED757PSYMTOPC / Crompton / Syska / Wipro / Philips

S&F in replacement MCB, TPN 63 Amps, having breaking capacity 10 KA, 'C' Curve complete all as specified and directed by Engineer-in-Charge. Make :- Legrand Cat Part No 408683 or equivalent in L & T / Crompton / ABB

S&F in replacement MCB 6 to 32 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :- Legrand Cat Part No 408587 to 408595 or equivalent in L & T / ABB / Schneider

S&F both side glow sign board made out of acrylic sheet / polycarbonate having thickness not less than 6mm thick on a sheet metal box frame of size 150cm x 90cm x 15cm fitted with and including 4 Nos LED 1x18 watt to make sign board glow at night or in dark environment fixed on and including approx 300cm long 50x6cm MS angle iron frame bracket and wiring (complaint cell, Garrison Engineer (Army) Suratgarh, Military Engineer Services) including connection from nereby street light pole box painting of MS angle iron frame bracket with 2 coats of synthetic enamelled paint fixed at site by grouting the legs of frame in PCC (1:2:4 type B1) block of size 30cm x 30cm x 60cm complete all as specified and directed by Engineer-in-Charge. Note : Top of sign board shall be 2.2 metre from ground level. Legs shall be embedded in PCC block upto 50cm depth. 20cm long holdfast made of MS angle iron of size 30 mm x 30 mm x 5mm shall be welded at bottom of each leg. Letters/matter etc for sign board shall be given by the Engineer-in-charge as per location of sign board. ------------------------------------------------------------------------ Note :- A sum of Rs. 109574/- will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 20 & 21 (Schedule of Credit) of Tender documents.

SRI SAI CONSTRUCTION COMPANY

Gupta Suppliers

GARG ENTERPRISES

MAJOR REFREGERATION AND ELECTRICALS