Renovation of Sub Health Centre(HWC) at Village Sherpura in SirsaDistt. (Re-invited)

Amount

Civil work

Scraping of Cement plaster (HSR 8.32 c)

Dismantling Brick work, tile masonery or tile (lining and tile tracing bathroom & toilet) (HSR 8.5) (b)

Dismantling of concrete (e) reinforcement with cleaning and sraightening & cutting of bars it required (HSR 8.6) (e)

Removing doors and window /wooden and steel to gether with athe chokhat by making secesses in wall whom the wall is not to be dismantalled (HSR 8.18)

Window

Dismantling cement conglomerate/terrazzo-floors 25 mm to 50 mm thick including concrete base (HSR 8.25)

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, (HSR 6.6)

Cement concrete 1:8:16 with stone aggregate 40 mm nominal size in foundation and plinth (HSR 10.28)

First calss brick work laid in cement sand mortar 1:6 in foundation and plinth (HSR 11.2)

Damp proof course 40 mm thick of cement concrete 1:2:4 using stone aggregate with 2 coats of bitumen 20/30 penetration at 1.65 kg per sqm laid hot and sanded. (HSR 10.114)

Base couse 1:8:16 (100mm thick) (HSR 14.1)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling (HSR 14.9)

Providing and fixing glass strips 5.5 mm thick 40 mm wide in floors. ) (HSR 14.80)

First class brick work laid in cement sand mortar 1:7 in first storey upto 4 metres above plinth level (HSR 11.6)

Providing 5.72 cm brick dalli facing with brick size 22.86 cm X 11.43 cm. X 5.72 cm thick to be obtained after cutting of bricks laid in cement sand mortar 1:3 on RCC lintels, beams fascia etc. including centring and shuttering complete (HSR 11.98) (a)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work (HSR 10.86+10.95a)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work (HSR 10.82+10.95a)

Pdg. & fixing Wrought iron and wild steel Grills stainless steel railing with SS grade 304 (NS)

Factory manufactured solid flush door shutters, with block board core as per I.S. No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II , fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position):-- (a) (HSR 17.93)

Providing & fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand morter 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles, Note:- Tile shall be premium quality (First quality) of reputed manufacturar like NITCO, KAJARIA, SOMANI, ORIENT , JOHNSONS & RAK.( HSR.14.89)

Laying and fixing Kota stone in all shades 15 mm to 18 mm thick in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite stone.

Fixing and laying required size of glazed tiles with DESIGN PRINTED for Windows & Door Borders (Satin finish) in dado set in CM 1:3 with joints so as to form a true & even surface and joints finished neatly with white cement mixed with matching pigments all complete as directed. (Rate should include base plastering with CM 1:5 of required thickness.) (HSR 14.92(b)) Labour rate The rate shall include cost of customized printing at top of the tile all complete as the details given by National Health Mission Haryana / HLL directed. (Kindly refer tender documents for Design details) (Tiles will be supplied by the Department.)

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (b) size of ceramic glazed tiles 300 x 450 mm [HSR 14.92(b)].

Two range of curtain cloth – Type 1 - II. Both for doors, windows and partions. Assorted colours plain & prints. Stitched as per site/ size requirement. Minor modifications in stitching as per site/ size requirement. Preferred colour (Brown, Cream, Beige).Curtain price (including cloth & curtain rod) to be quoted in Squre metre. Stitching for each curtain to be absorb in the price of the cloth generally 2 meters.Fast colours, water wash.Fabric density Non Transparent Composition. Fabric of curtain shall be soft texture, great shading, drape effect and nice dobby. The bracket shall be side mounted and front mounted as required. First rod mount is 3.5 inches from the wall. Where curtain used as a partition/ long length, sufficient support from ceiling should be provided to avoid sagging.Rate quoted for fully stitched Curtain with top nepha with punch holes after lining bucramreinforced with SS / PVC islets and lower nepha 200mm double turned. Type - II (Window & Door Curtain)Curtain fabric weight shall be up to 250-275 (±5%) gsm Composition of fabric shall be polyester yarn I.E. 300 denier fast colour sink age shall be (±5%) Weft and warp shall be polyester / cotton polyester mix (NS)

Providing and Fixing of Compressed form board with digital prints (NS)

Providing and Fixing of Flex print board with MS Pipe Frame (NS)

Providing and fixing Elliptical Machine for Standing on the Pedals, Holding the armrest, moving the feet as walking on the ground with hands move accrodingly of appx weight 38 kg. (NS)

Providing and fixing Air Walker/ Riding Trainer for clenching the horizontal bar with two hands, pedaling on the pedals and leaning the upper body forward, with a slightly bend of the legs then moving the legs as walking with appx. Weight of 40 kg. (NS)

Providing and fixing for Sit up board (dual) for lying in the board, hooking the bar by your feet, hand cross behind your head, take a deep breath and than do sit up exercise with a appx. Weigth of 70 kg. (NS)

Providing and fixing Body rider for sitting on the seat, cleanching the horizontal bar furmily, Pedal the Pedals, and trying best to pull the bar horizontly with a appx. Weigth of 26 kg. (NS)

Pdg. Three Seater Waiting Area Visitor Reception Chair in Chrome Finish (NS)

Plastic Pedal Garbage Waste Dustbin 15 LTR (Blue + Green + Red Pack Of 3) WITH CHECK DUSTER CLOTH FREE (NS)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge) INDIAN TYPE WATER CLOSET SUITE CONSISTING OF :-- (i) Closet set VITREIOUSCHINAWARE W.C. PAN WITH horizontal inlet, for sinking into floor with A PAIR OF FOOTRESTS, 100 MM H.C.I. ‘P’ TRAP WITH or without vent as required and suitable joint for closet inlet; ( 30.a(i) (a) Size 580 mm (i) White

Providing and fixing in position best indian make (as approved by the engineer-in-charge) European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (a) single trap syphonic W.C. Suite (i) White [HSR 30.5 (a) (i)].

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY LOW LEVEL VITREOUS CHINA WARECISTERN complete with flush bend all other necessary fittings instead of C.I. high level cistern complete with fittings. White (HSR 30.12 i)

Providing and fixing in position best indian make (ordinary) lavatory suites consisting of lavatory in vitreous chinaware size as given below (to the approvalof the Engineer-in-charge) including china plug for tap hole where necessary; RS or C.I Brackets for building into wall including painting; 32 mm C.P. Brass waste with C.P. brass chain and rubber plug; 15 mm C.P. Brass screw down piller tap with jamnuts or couplings best design (as approved by the Engineer-in-charge) All fittings Best Indian make and; to the approval of the Engineer-in-charge. All brass work chromium plated and complete in all respects including cutting and making good the walls, floors and Painting of fittings etc.White (IV) -size 550 mm x 400mm with one no tap (HSR. 30.41-white-iv)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in- charge) bib cock (HSR 30.75- c)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MMTHICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embeded in the wall of chromium plated brassclamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. indian make 600mm X 450mm (HSR 30.71 A-1)

Providing and fixing HDPE water storage tanks of sintex, diplast o.k. supreme make with covers/lids marked with IS 12701 on roof top of building i/c cost of hoisting and placing in position making connections with inlet and outlet pipes providing overflow and scour provisions with suitable plug on scour pipe i/c cost of nipples, washers, flanges, for connections in tanks complete in all respect to the satisfaction of Engineer-in-charge. except civil work 1000 Ltr. Capacity (HSR.30.119)

Providing and fixing in position best quality stainless steel sinks with complete fittings as fully described in item no. 30.51 above(a) 600mm X 450mm X 200mm-(HSR 30.53 -a)

Providing & Fixing of G.I. Pipes 15 mm internal dia (NS)

Providing & Fixing of G.I. Pipes 25 mm internal dia (NS)

PROVIDING AND FIXING IN POSITION GLASS SHELF FIXED IN WITH RAWL PLUGS WITH C.P.BRASS SCREWS COMPLETE INCLUDING CUTTING AND MAKING GOODS THE WALLS ETC. (a) with c.p. brass brackets and guard rail (i) 600mm X 125mm (HSR 30.69-a-i)

EXTRA FOR providing and fixing 32 MM dia G.I./C.P FLUSH PIPE complete with accessories instead of 32/MM dia galvanized telescopic flush pipe with clips (as required by the Engineer-in-charge). (i) 32 mm dia G.I. flush pipe. [HSR 30.15 (i)].

Providing and fixing 40 mm I/D Stainless Steel waste pipe embedded in walls or lead waste pipe weighing 4.46 Kg./metre and 3.0 mm thick upto floor level as required by the Engineer-in-charge including cost of union and plumber joint. (HSR 30.62)

Providing and fixing 40 mm i/d chromium plated brass trap with chromium plated bra pipe to wall with wall flange, complete (as per requirement of the Engineer-in-charge) for use with sinks. (a) with Bottle Trap (indian make). [HSR 30.63 (a)].

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE PAPER HOLDERS FIXED INTO wall with C.P Brass screws complete in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (a) C.P. Brass. [HSR 30.67 (a)].

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making goods the walls etc. (a) C.P. Brass (i) Soap dish Large. [HSR 30.70 (a) (i)].

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (ii) Concealed stop cock with flange. [HSR 30.76 (a) (ii)].

Providing and fixing C.P brass liquid soap container of best quality (as required by the Engineer-in-charge). [HSR 30.77].

Providing and fixing in position best Indian make flexible tube connection. (b) C.P. Brass (iii) 15mm x 450 mm. [HSR 30.82 (b) (iii)].

Providing and fixing in position H.C.I. Soil waste vent or antisyphonage pipes to I.S.I. specifications of E.L.C. manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floor etc. and making good to its original condition but excluding cost of lead jointing. (HSR 30.84)(a) 100 mm internal diameter.

(b) 75 mm internal diameter.

Providing and fixing in position C.I. Gully trap cover weighing approximately 7.26 Kg. and frame for gully trap chamber clear opening size 300 mm x 300 mm and out side size 330 mm x 330 mm including painting the exposed surfaces with 3 coats of black bitumastic superior paint of approved manufacture etc. (HSR 30.85).

CONSTRUCTING BRICK MASONRY INSPECTION CHAMBER SIZES AS GIVEN BELOW UPTO 0.60 METRE AVERAGE in cement mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 BENCHING 12 mm THICK CEMENT PLASTER 1:2 with a floating coat of 1 mm thick of neat cement R.C.C. 1;2:4 SLAB 100mm THICK/C.C. TOPPING 50 mm THICK WITH 455 MM X 455 MM /455 MM X 610 MM INSIDE LIGHT DUTY C.I. INSPECTION CHAMBER COVER AND FRAME weight as per I.S.I. specification painted WITH 3 COATS OF black bitumastic superior paint complete as per standard design. (b) Size 450 mm x 600 mm inside (with 455 mm x 610 mm cover and frame single seal pattern I weighing 38 kg with C.C. topping) ( HSR 29.84 (B)

EXTRA FOR EVERY 0.30 METRE DEPTH OF INSPECTION CHAMBER (b) 450 mm x 600 mm ( HSR 29.85 (b)

Constructing brick masonry inspection chamber sizes as given below upto 0.60 metre average depth in cement mortar 1:5 lime concrete with 40 percent limer mortar 2:3 in foundation cement concrete 1:2:4 benching 12 mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement R.C.C. 1:2;4 slab 100 mm thick./C.C. topping 50 mm thick with 455 mm x 455 mm 610 mm inside light duty C.I. inspection chamber cover and frame weight as per I.S.I. specification painted with 3 coats of black bitumastic superior paint coplete as per standard design. (a) Size 450 mm x 450 mm [HSR 29.84-a].

Providing and fixing in position H.C.I. specials for soils, waste, vent or anti-syphonage pipes to I.S.I. marked including cutting and waste etc. cutting holes in walls roofs or floors etc., and making good to its original condition but excluding cost of lead jointing. (HSR 30.91). (a) For 100 mm dia pipes (1) Heal rest bend

(2) Double Junction with door 100 mm x 100 mm x 100 mm x 100 mm

(4) Single Junction with door 100 mm x 100 mm x 100 mm x 100 mm

(13) Bend with Door

(14) Bend Plain

(16) Cowls

(17) Door piece

(22) Collars

(b) For 75 mm dia pipes (1) Heal rest bend

(3) Double Junction with door 75 mm x 75 mm x 75 mm x 75 mm

(4) Single Junction with door 75 mm x 75 mm x 75 mm x 75 mm

(13) Bend with Door

(14) Bend Plain

(16) Door piece

(17) Cowls

(18) Collars

Providing SALT GLAZED STONE WARE PIPES GRADE ‘A’ IN STANDARD LENGTH OF 600MM EACH PIPE MARKED WITH IS:651 and their lowering, cutting, jointing and testing as described in HSR item No.29.38, 29,39, 29.40 including the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc complete in all respects to the satisfaction to the Engineer-in-Charge. ( HSR 29.95) 200 mm i/d

Providing and fixing in position automatic brass ball valves in tanks. (b) With Plastic Ball (ii) 20 mm internal diameter. [HSR 30.110 (b) (ii)].