Upgradation Beautification of Places of Touristic Interest in Bicholim Taluka Regd Upgradation Beautification of Bramhaneshar Temple Bicholim

Amount

Civil Works

Clearing grass and removal of rubbish upto a distance of 50 m outside the periphery of the area

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in : All kinds of soil

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in : All types of Ordinary rock including all types of laterite rock, blasting prohibited

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. All kinds of soil

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. All types of Ordinary rock including all types of laterite rock, blasting prohibited

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer in Charge.

Pre-cast cement concrete solid block masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in foundation and plinth size of blocks (30 x 20 x 15)

Pre-cast cement concrete solid blocks masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in partition walls size of blocks (30 x 20 x 10)

Extra for precast concrete block masonary in all sizes in superstructure from floor one level upto floor V level

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level.

Random rubble masonry of laterite stone not less than 20 cm laid dry in pitching rivetment etc.

Providing & laying cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: All works upto plinth level

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: In retaining walls , return walls(any thk) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping bed blocks, anchor blocks, plain window sills, fillets etc, upto floor five level.

Centering and shuttering including struttings, propping etc. and removal of formwork for : Foundations, footings, bases for columns and mass concrete.

Centering and shuttering including struttings, propping etc. and removal of formwork for : vertical surfaces such as retaining walls , return walls, walls (any thk) including attached pilasters, buttresses, plinth and string courses, fillets, etc.

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) All works upto plinth level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) In walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and structs etc. upto floor five level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) In beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases upto floor five level

Centering & shuttering including Strutting, Propping & removal of forms for : Foundations, Footings, Bases for columns

Centering & shuttering including Strutting, Propping & removal of forms for : Columns, Piers, Pillars, Aburments, Posts and struts (square rectangle polygon in plan)

Centering & shuttering including Strutting, Propping & removal of forms for : Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth

Centering & shuttering including Strutting, Propping & removal of forms for : Arches, domes, vaults upto 6.00 span

Centering & shuttering including Strutting, Propping & removal of forms for : Suspended floors, roofs landings, shelves & their supports

Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

12mm cement plaster 1:3 (1 cement : 3 fine sand)

6mm cement plaster to ceiling 1: 3 (1 cement : 3 fine sand)

Neat Cement punning

Providing and Laying 50mm thick Cement plaster in 1:3 cement mortar (1: cement 3: fine sand) in double layers including chicken mesh fixed in first layer of cement plaster, neatly finished sponge plaster in proper line, level and plumb in curves, mouldings, cornices, projections, bands, grooves, niches etc all complete as directed by Engineer In-charge

20mm cement plaster 1: 3 (1 cement : 3 coarse sand)

Extra for providing and mixing water proofing material proportion recommended by the manufacturers. 20mm cement plaster 1: 3 (1 cement : 3 sand)

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Finishing wall with superior quality waterproofing cement paint (super snow hem or equivalent) of required shade on new work (three or more coats) to give an even shade.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Steel work in single sections (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only) including cutting, hoisting fixing in position and applying a priming coat of red lead paint. In R.S. joists, channels, angles, tees

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of approved make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Supply and installation of Aluminium Louvers. The frame should be made of Aluminium tubes of size 100x50X1.50 mm thk and 50X25x1.50 mm thk C channels. Aluminium Z shaped louvers of 100mm should be fixed to the supporting frame with aluminium cleats, GI screws, etc complete. The whole assembly is powder coated with pure polyester paint. (MS framing to be paid separately)

Providing and fixing prefabricated compound gate of G.I. pipes 40 – 50 mm dia (medium) with 12mm M.S. square bars of G.I. pipes grill work as per drawing including providing & fixing locking arrangements, pintals, hold fast embedded in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 granitic or basaltic aggreate 20mm nominal size) including applying priming coat with ready mixed red lead paint and painting 2 or more coats with superior ready mixed paint of approved brand and manufacture in all shades as per direction complete.

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. Wall Ceramic Glazed Tiles : 300 x 450

Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. 40 mm thick

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm Jet Black

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) 20 mm thick.

Providing and fixing vitrified matt finished (600x600) and 10mm thick tiles in floor, treads of steps, landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete.

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. 60 mm thick in all colours except grey

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer : Flamed finish granite stone slab. Elite Brown

Providing and fixing Granite stone slabs (flamed finish) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete Elite Brown

Providing and laying 1st class mangalore tile roof covering with 25 x 50mm (1” x 2”) jamba wood or similar batten including nails etc. but excluding rafters.

Providing and laying ridge tiles laid dry & pointed with lime mortar 1: 2 (1 lime: 2 surkhi)

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge.

Add for providing & fixing Flashings -[Corners, Ridges, valleys, gable end & Trims] (Girth upto 610mm) including all the accessories complete as per the directions of the Engineer in charge.

Providing and fixing PVC SWR pipes confirming to IS 13592 type A including jointing with seal ring confirming to IS 5382 leaving 10 mm gap for thermal expansion. Single socketed pipe 110 mm dia

Providing and fixing Prince or equivalent make PVC SWR half round eaves gutter with bolts, nuts and flat iron brackets 40 x 3 mm size complete. 250 mm nominal size

Extra for providing and fixing prince or equivalent make PVC SWR joint bracket with 2 clamps for socketed half round eaves gutters. 250 mm nominal size

Extra for providing and fixing prince or equivalent make PVC SWR 90 deg. Elbow with /without outlet with 2 clamps for socketed half round eaves gutters. 250 mm nominal size

Extra for providing and fixing prince or equivalent make PVC SWR stop end outlet with one clamp for socketed half round eaves gutters. 250 mm nominal size

15mm cement plaster 1: 3 (1 cement : 3 fine sand) on the rough side of single or half brick wall.

Painting (two or more coats) with synthetic enamel paint of approved brand and manufacture in all shade on new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture to give an even shade

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Demolishing brick work in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Dismantling steelwork in built up sections in angles, tees, flats and channels including all gusset plates bolts, nuts, cutting dismembering and staking within 50 mts. lead

Dismantling the tile work in floors and roofs laid in cement including stacking of materials within 50 meters lead for thickness of tiles 10mm to 25mm.

Dismantling asbestos sheet roofing including ridges, hips valley and gutters and stacking the material within 50 meters lead.

Dismantling tiled roofing (mangalore or pot or country tiles) with battens etc. complete including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Supplying and stacking of good earth at site including royalty and carriage upto 1 km. (earth measured in stacks will be reduced by 20% for payment).

Spreading of sludge, dung manure or/and good earth in required thickness (cost of sludge, dung manure or/and good earth to be paid separately).

Supplying of sludge duly stacked at site/store as per MORTH Specification 308.2

Making lawns Using Mexican Ready Lawn , 1 x 2 feet size panels each including finishing the base, breaking of clods, removal of rubbish, dressing , planting lawn at 15 cm apart, including supplying and spreading of farm yard manure at rate of 0.18 cum per 100 sqm

Providing and fixing mobile Dust bin of capacity as specified, Nilkamal make or equivalent as shown in the drawings, installation as per manufacturer specification, including all fittings and fixtures etc complete as directed by Engineer Incharge. WB 240ltr

Supplying and fixing Pre-cast cement concrete kerb-stones(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) of M-20 with 20 mm nominal size granitic/basaltic aggregate properly consolidated by mechanical plat-form and vibrators with smooth finish including fixing at site complete as per specification. Size 30 cm L x 50 cm H x 15 cm T

Supplying and fixing of Precast RCC slabs(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) at site in concrete Grade of M-25 with 20 mm nominal size Granitic or basaltic aggregate, consolidated by means of mechanical platform, vibration etc. with lifting hooks of M.s. 10mm bars and PVC cups including cost of reincforcement, Certificate from manufacturer shall be produced indicating grade of concret and minimum content of steel in the product along with 5 year free replacement warranty in case of breakage complete and as directed by Engineer -in -charge. Size 900 x 400 x 100 mm with steel reinforcement not less than 5.0 kgs per unit -12 T capacity

Providing and Painting (two or more coats) with synthetic enamel paint of approved brand and manufacture in all shades on external wall , including one or two coat of external cement primer, neatly finishing in all levels, cornices, mouldings, grooves, all curved/round surfaces, architectural surcfaces, all complete etc, as directed by Engineer Incharge

Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Centering & shuttering including Strutting, Propping & removal of forms for columns, pillars, struts (circular or curved in plan having average diameter not greater than 600mm) having cornices, mouldings grooves, ets complete as directed by Engineer Incharge.

Providing & fixing bright finished brass 100 mm. mortice latch & lock & a pair of levers, handles with necessary screws etc. complete (Indian make of approved quality).

Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in positon. First class matti wood

Providing and fixing 35 mm thick panelled glazed or panelled and glazed shutters for doors, windows and clerestory window including anodized aluminium butt hinges with necessary screws: First class Indian teak wood

Providing and fixing bright finished brass door latch with necessary screws etc complete 300x 16 x 5 mm

Providing and fixing bright finished brass tower bolts (barrel type) with screws etc. complete 250 x 10 mm

Providing and fixing M.S. door latch with screws etc. complete 300 x 20 x 6 mm

Providing and fixing bright finished brass handles with necessary screws etc complete 125 mm

Providing and fixing 12 mm sheets flat pressed three layered melamine faced prelaminated wood based particle board bonded with BWP/BWR exterior grade synthetic resin penaling / cladding as for wall panelling / cladding as per IS-3087 (1985) type I one side approved shade and other side balancing white lamination of Novapan make or equivalent to be fixed to frames by cleates, leaving expansion allowance of 6 MM in between each panel. The width of the panel can be 1.5 feet/2 feet/3 feet as per Architects discretion. Second class teak wood.

Providing and fixing flush door shutter of solid core melamine face three layered, prelaminated wood based particle board exterior grade having shade of choice on both sides (PTX) or having shade of choice on one side and balancing lamination on the other side (PLX) as per IS 3087 (1985) type I on the edge of Novopan or equivalent bonded with BWR/BWP synthetic resin with second class teak wood, lipping of section of size 12 mm x 30 mm flange and 18 mm x 10 mm web (18 mm deep) fixed into 18 x 10 mm groves of shutter with water resistant adhesive and fully threaded G.I. screws 50 mm not more than 450 mm centre to centre including anodized aluminium butt hinges with necessary screws etc. complete. White balancing lamination on one face and natural teak on other face 30mm thick

Providing and fixing louvers 50 mm wide in grooves in clerestory window frames excluding the cost of frames. Frosted glass sheets 3mm thick

Providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut granite frames in doors, windows, ventilators and similar location as shown in the drawings, width of the frame not more than 300mm made up of two peices of granite of equal width having overlap 75mm as directed, including holes for recieving screws, locking slots, hold fast, rubbing, curing, moulding and polishing to edges to give high gloss finish etc complete at all levels.

Providing and laying 18mm thick cement plaster in cement mortar 1:4 (1: cement 4: fine sand) along with neat cement punning under two layers 12mm and 6mm respectively on circular surfaces on columns having average diameter not greater than 600mm.The cement mortar is being mixed with water proofing compound proportion as specified by the manufacturer, neatly finished cement plaster in proper line, level and plumb etc all as directed by Engineer Incharge.

Proving and fixing white vitreous china water closet squatting pan (Indian type w.c. pan) size 580 mm with 100 mm sand cast iron P. or S trap 10 litres high level P.V.C. flushing cister (of approved make) with fittings, rack bolts 32 mm diameter P.V.C telescopic flush pipe with fit tings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon pull complete cutting and making good the walls and floors where required. Orissa pattern W.C. pan

Proving and fixing white vitreous china water closet squating (European type w.c. pan) with seat and lid, C.P. brass hinges and rubber buffers 10 lts. High level P.V.C.. flushing cistern (of approved make ) with fittings, rack bolts 32 mm diameter P.V.C. telescopic flush pipe with fit tings and clamps 25mm P.V.C.. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon. chain and pull complete, cutting and making good the walls ad floors where required. W.C. pan with white plastic seat and lid.

Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white, 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. brass trap and union complete, including cutting and making good the walls where required. Flat back wash basin size 630 x 450mm with a pair of 15 mm C.P. brass pillar taps.

Providing & fixing c.p. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C. P. brass screws 750 x 20 mm size

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality : 25 mm nominal bore .

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality : 50 mm nominal bore .

Providing and fixing P.V.C. connection pipe with brass unions 15 mm nominal bore: 45 cm (18”) length .

Providing and fixing C.P. brass shower rose with 15 or 20 mm. Inlet: 150 mm diameter.

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996. 1000 lit. capacity

Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with c.i. grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than 2.72 kg as per standard design : 150 x 100 mm size –P or S type

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand ;4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement ;2 coarse sand :4 graded stone agrregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cemetn and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design. Inside size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty) 455x610mm internal diameter total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg).

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed: 110 mm dia

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed: 75 mm dia

Supplying of heavy duty C.I Cover with frame weighing not less than 230 kg- 500mm diameter as per IS 1726-1976 with latest ammendments

Making soak pit. 2.5 m dia 3 m deep with 45x45 cm dry brick honey comb shaft and S.W. drain pipe 100 mm diameter, 1.8 m long complete filled with laterite stone aggregate 125 to 180 mm surrounded by laterite stone aggregate of 40 mm and down gauge as per standard design.

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. 75 mm dia

Providing and fixing single tee of rigid PVC (approved make) for S.W.R. pipes including lubricating etc. complete, without door: 75 mm dia.

Providing and fixing nahani trap of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door : 110 mm dia

Providing and fixing R.P.V.C. vent cowl: 110 mm dia

Providing and fixing NICKEL chrome plated copper alloy Fancy BIB Cock Short Body Jaquar make or equivalent. Confirming to IS 8931;1993 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy two way long body bib cock with wall flance Jaquar make or equivalent. Confirming to IS 8931;1993 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy wall mixer with 115mm long bend pipe for connection to over head shower Jaquar make or equivalent. Confirming to IS 8931;1993 Wall mixer with 115 mm long bend pipe for connection to over head shower.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 15 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 20 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 25 mm dia nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement, trenching, refilling and testing of joints complete as per firectionof the Engineer in charge.(External work (heavy duty SDR 11 pipe) 40 mm nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement, trenching, refilling and testing of joints complete as per firectionof the Engineer in charge.(External work (heavy duty SDR 11 pipe) 50 mm nominal outer dia pipes.

Providing & fixing bevelled edge mirror of superior glass (5mm thk) of approved Quality, shape & size complete with CP brass screws and washers, Cleats, CP studs etc Complete.

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing & fixing 2 way angular stop cock with wall flange of 20 mm dia bore without tap. Of first quality chrome. JAGUAR FLR-5053N or equivelant etc. complete

Providing and fixing (100 mm) SS grating for gully flooring and Nahani trap, etc. complete

Providingan fixing Soap Dispensor of Jaguar make with CAN-1137 N or Equivalent

Toilet Roll Holder with Flap - Jaquar make (ACN- 1153N)

Providing and fixing C.P. brass double coat hook, including all fittings and fixtures etc complete. Jaquar (ACN-1161N) or equivalent

Providing and fixing digital water heater Jaquar make or equivalent 25liter capacity with remote control, including brackets, screws, nuts and bolts all fittings and fixtures etc complete as directed by Engineer Incharge Jaquar :(Elena Digital 25liters)

Electrical Works

Temple Panel: Supply, Installation, testing and commissioning of panel IP-52 indoor type, wallmounted comprising of AL Bus Bar of 250 Ams with, earth bus bar complete as per specifications with 120 A MCCB and with 3 phase ct energy meter and 120 A manual changeover for alternate supply with 3 sub outgoing of 40A and 23nos 10A SPN mcb and 12nos 16A SPN mcb as shown in single line diagram, Panels shall be suitable for 415 V, 3 phase, 4 wire, 50 Hz supply system, including voltage stabilizers. Lifting hooks shall also be provided for all sections of panels, with cable entry from bottom for incoming & outing.

Arc Panel: Supply, Installation, testing and commissioning of LT panel IP- 67 outdoor type,wall mounted Panels shall be suitable for 415 V, 3 phase, 4 wire, 50Hz Supply system. With 3 phase energy meter and 32A TPN MCB as incommer and 6nos 10A SPN MCB as outgoing. As shown in SLD.

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size.. 3 Core 4 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 4 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 10 sq.mm

Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 2.5 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 1/2 Core 120 sq.mm

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed /XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (1) 3 x 1.5/2.5 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed /XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (2) 3 x 4 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (2) 4 x 4 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (6) 4 x 10 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (6) 3 1/2 x 120 Sq. mm.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge, sand cushioning with screened sand bed of 20mm thick, protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (a) In soily strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run (the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (a) In soily strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 400 sq.mm in the existing RCC /HUME / STONEWARE Metal pipe, etc. complete as required

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark,of approved brands, including accessories and providing masonry enclosure with CI/RCC cover having locking /lifting arrangement and watering pipe etc. with charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g) watering arrangement (a) In soily strata

Providing and fixing 6 SWG dia GI wire on surface or in recess for loop arthing along with existing surface/ recessed conduit/ submain wiring/ cable as required

Providing and fixing 25 mm x 5 mm GI strip on surface or in recess for coneections etc. as required

Supply & erection of Antique Decorative arthitectural 3 meter cast iron pole, Primered and PU painted factory Finished. The column must have a hinged flush door at the bottom with proper strengthening to the cutout of the door opening. A junction/ looping box with 32 Amps heavy duty connector shall be built in to the pole and with provision of SP MCB, provided with a base plate and one set (4 Nos.) of SS J-bolts, and suitable for mounting of 40 watts LED luminair or pole equivalant subjected to approval of sample by engineer in charge and with other required accesories. Exclusive of MCB and 3c 2.5 sq mm wire from MCB to Fitting

Supply ,Installation Testing , Commissioning of IP65 LED luminaire 30 Watts LED luminaire with die cast aluminium housing of IK 08 of Atlantis make with Catlogue No : SL 1248 30 or equivalent subjected to approval as directed by Engineer In -charge.

Supply , installation , testing and commissioning of IP65 rated Led strip of 5 meters with rated wattage of 9.6 watts / meter with IP 65 rated equivalent driver for LED of color: WW/W/CW/DW of IK 08 rating of Atlasntis make with serial number LS65-096-50-13-XXK or equivalent subjectde to approval by Engineer incharge.

Supply , installation , testing and commissioning of IP 65 rated equivalent driver for LED Strip Light of 5 meters with rated wattage of 9.6 watts / meter.

Supply , installation , testing and commissioning of IP65 Mid bay light fitting of 27 watts IK 09 including mounting bracket and required arrangements of Atlantis make of Catlogue No : CSR0027 - A or equivalent subjected to apprval from engineer incharge

Supply , installation , testing and commissioning of IP65 6X2W LED Flute LED light with 20 degree Beam angle including mounting bracket and required arrangements to get the proper effect of Atlantis make with Catlogue No : FLCSP012 or equivalent subjected to approval from engineer incharge.

Supply , installation , testing and commissioning of IP 65 rated equivalent driver for Flute 3 light fixture 24V, IP67 Driver - 60w.

Supply , installation , testing and commissioning of IP65 Down light fitting of 1x7 watts with Narrow Beam angle including mounting bracket and required arrangements of Atlantis make of Catlogue No : FLCSP007 or equivalent subjected to apprval from engineer incharge

Supply , installation , testing and commissioning of IP65 Down light fitting of 1x7 watts with Wide Beam angle including mounting bracket and required arrangements of Atlantis make of Catlogue No : FLCSP007 or equivalent subjected to approval from engineer incharge

Supplying and erecting corridor/passage light fitting (2 feet) including 9W LED lamp, comprises of extruded channel in plastic silver grey colour & with same plastic end cap on provided PVC block / wooden board.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor single core cable in the independent surface/ recessed FRLS PVC conduit of appropriate size as required. (a) 2 x 1.5 sq.mm + 1 x 1.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor single core cable in the independent surface/ recessed FRLS PVC conduit of appropriate size as required. (b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required. (c) Group C -- with Cat A Modular Accessories

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/16 A modular switch connection painting etc. as required. (a) Cat A

Supply and erecting of 12 inch (300 mm sweep) exhaust fan, 1400 rpm, complete with all accessories. (a) Cat A

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) (b) 8 way single door Cat A

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) (c) 12 way single door Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (a) SP, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (c) DP, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (e) TPN, Cat A

Supplying and fixing SP blanking plate in the existing MCB DB complete as required

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. All kinds of soil

Centering and shuttering including strutting, propping etc. and removal of formwork for : Foundations, footings, bases for columns and mass concrete.

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: All works upto plinth level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) All works upto plinth level

Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Laying and fixing with collars light duty non-pressure NP 2 class R.C.C. pipes with cement mortar in proportion 1:2 (1 cement : 2 fine sand) in joints including cost of jointing material etc. complete. 300 mm dia pipe

Supply, installation , testing and commissioning of Terminal Boxes size 88 x 88 x 53 mm with 9 Nos 4 sq.mm Terminals. Box shall be similar to Hensal make Cat. No. TB 0409, IP 65,

Terminal Boxes size 200 x 160 x 98 mm for cable junction / driver placement with Terminals and all the required accessories. Box shall be similar to Hensal make Cat. No. K 9255, IP 65

Supplying and fixing 10 A 240 V SPN industrial type socket outlet with 2 pole and earth metal enclosed plug top alon with 20 A, C series SP MCB in sheet steel enclosure in surface or in recess with chained metal cover for the socket outlet and complete with connections testing and commissioning etc. as required. (a) Cat A

abdul khadar