Providing Shed on H.V.A.C. System in Civil Hospital Hisar

Amount

CIVIL WORK Cement concrete 1:1 1/2:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centering and shuttering , laid in position, complete in all respects. (HSR 10.82+10.95 a).

Cement concrete 1:1 1/2:3 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20 cm thickness (straight and curved) beams, girders, stairs, columns, (square or rectangular) battens and lintels etc. excluding steel reinforcement but including centering and shuttering, laid in position, complete in all respects. extra over Item Nos. 10.79 to 10.94, if 1:1 ½:3 mix is used, instead of 1:2:4. (HSR 10.86 + 10.95 a) .

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level. (HSR 11.7) .

Conglomerate floor 50 mm thick cement concrete topping 1:2:4 (HSR 14.10) .

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note: - Tile shall be premium quality (1st quality) of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JONHONSONS, ORIENT BELL, SIMPOLO shall be used as approved by Engineer-in-chargeS. (HSR 14.89) . Note:- The agency to whom the work is allotted will have to produce original bill/voucher for al quantity in token of proof of purchase of material.

Providing & fixing of 1st quality Ceramic Tiles/ anti skid tiles of size 400 x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note: - Tile shall be premium quality (1st quality) of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JONHONSONS, ORIENT BELL, SIMPOLO shall be used as approved by Engineer-in-charge. (HSR 14.91) Note:- The agency to whom the work is allotted will have to produce original bill/voucher for al quantity in token of proof of purchase of material.

Providing & Fixing Ist quality glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed to match the shades complete. (HSR 14.92 (a) Size of Ceramic Glazed tiles 200mm x 300mm of reputed manufacturer like NITCO, KAJARIA & RAK, NITCO, KAJARIA etc. (b) Size of ceramic Glazed tiles 300mm x 450mm. (HSR 14.92 (b) Note:- The agency to whom the work is allotted will have to produce original bill/voucher for al quantity in token of proof of purchase of material.

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.12) .

10 mm thick cement plaster 1:4(Hsr 15.52) .

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade.(HSR 16.3) .

Applying priming coat with metal primer on New steel or iron work including preparation of surface. (HSR 16.9) .

Preparation of plastered or concrete surfaces for painting, including sand papering the surface, applying one coat of linseed oil and filling with approved quality filler, consisting of white lead, linseed oil, varnish and chalk mitti including finishing surface to the required finish, complete.(HSR 16.24) .

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25) (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Jenson, Nicholson, Asian & Shalimar shall be used a approved by the Engineer-in-Charge in writing, Drum of paint shall be opened in presence of Engineer-in-Charge) .

Painting two coats with plastic emulsion paint on walls on new work to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Jenson, Nicholson, Asian & Shalimar shall be used a approved by the Engineer-in-Charge in writing, Drum of paint shall be opened in presence of Engineer-in-Charge) (HSR 16.30) .

Providing two coats of exterior acrylic emulsion paint. b) Ist quality. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Jenson, Nicholson, Asian & Shalimar shall be used a approved by the Engineer-in-Charge in writing, Drum of paint shall be opened in presence of Engineer-in-Charge) (HSR 16.79 ) .

Providing and laying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including coat and carriage of all material, labour charges, scaffolding, sundries etc. complete (J.K./Birla make) (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Jenson, Nicholson, Asian & Shalimar shall be used a approved by the Engineer-in-Charge in writing, Drum of paint shall be opened in presence of Engineer-in-Charge) (HSR 16.81) .

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS;733 and IS;1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling C.P brass /stainless steel screws , all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing and panelling to be paid for separately) Fixed portion (Anodised aluminium transparent or dyed to required shade according to IS;1868,minimum anodic coating of grade AC 15) (HSR 17.95)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS;733 and IS;1285 fixed with rawlplugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling C.P brass /stainless steel screws, etc. complete. (HSR 17.96) + Note Shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PBC/ neoprene gasket required including aluminium fitting i.e. Note: II) Add Rs.20/- Per Kg. extra if Polyester powder coating of 50 micron is done instead of anodizing in above item No. 9 & 10.aluminium kun)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS; 12823 grage 1 type II in panelling fixed in aluminium doors. Windows shutters and partition frames With C.P. brass /stainless steel screws etc. complete. .(HSR 17.97 b) (b) Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door, windows ,ventilator shutter and partitions etc. with pvc/neoprene gasket etc. complete (cost of aluminium snap beading shall be paid in basic items). (b) With float Glass panes of 5.00 mm thickness. (HSR 17.98 b)

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12) .

Supplying M S Bolts round holding down of Anchor bolts with nuts and washer plates complete.(HSR 18.15 b) .

Supplying, hoisting and placing in position tubular trusses including runners, purlins, consisting of steel tubes conforming to I.S. specifications of tested quality duly welded with fillet welds 6 mm thick through-out including wind bracing. Open end of pipe sealed with 3 mm thick plate including the cost of nuts and bolts where bolts connections are specified at flange joints including one coat of ready mixed red oxide zink cromate primer of approved quality assembling and fixed in positon complete in all respect. (HSR 18.14) .

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where not included in the complete rate of RCC including Straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in al respects for all heights/depths/storeys/basements etc. Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used inwork, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing be deemed to be included in the rates for reinforcement. (HSR 18.22)

Providing and fixing of 0.5mm thick colour coated profile sheet of approved make as per entire satisfaction of Engineer incharge (NS)

Providing and fixing of wire mess jali of size 4' x 50' weighting approximately 50 kg having squares size 3" x 3" complete in all respect. (NS)

PUBLIC HEALTH : Providing & Fixing PVC Rainwater Pipe 6 Kg. pressue of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-Charge. Note:- The agency to whom the work is allotted will have to produce original bill/voucher for al quantity in token of proof of purchase of material. (HSR 13.89) a) 100 mm dia PVC pipe

Providing & fixing PVC Bend ISI Mark. (Note:- Reputed make PVC pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-Charge. Note:- The agency to whom the work is allotted will have to produce original bill/voucher for al quantity in token of proof of purchase of material. (HSR 13.90 (a) 100mm dia PVC pipe

LABOUR FOR LAYING JOINTING, FIXING AND TESTING G.I/P.V.C/W.I PIPE LINES AND SPECIALS tees bends, Sockets elbows etc., INSIDE BUILDING and testing etc., complete including cutting threading. (HSR 28.18) (i) 15mm

LOWERING SALT GLAZED STONEWARE PIPES AND SPECIALS INTO TRENCHES for all depths AND LAYING OUT THE SAME to correct alignment gradient, level etc IN TRENCHES including all dressing and tremming of bed and sides of trenches, if required, trimming and cutting of concrete beds and joint holes, supporting rigid manner while the same are being jointed and until the surrounding benching haunching and envelopes are completed. The sewer shall rest on the bed at every point throughout its length and to ensure this, it shall be grouted in without extra charge by the contractor with lime surkhi mortar in the case of cement concrete beds INCLUDING CARTAGE from Divisional Store or nearest Railway station TO SITE OF WORK. (HSR 29.38 )

JOINTING AND FIXING SALT GLAZED STONEWARE PIPES AND SPECIAL IN TRENCHES USING CEMENT SAND MORTAR 1:1 AND BEST WHITE ITALIAN TARRED HEMP/YARN INCLUDING FINISHING and trowelling of EACH JOINT AT AN ANGLE OF 45 DEGREES with the longitudinal axis of the pipes, watering, keeping the joints covered and wetted till the same are cured, testing the sewer lines for leakages and making all leakages and defects good, complete as laid down in the contract specifications. (HSR 29.39)

CONSTRUCTING BRICK MASONRY INSPECTION CHAMBER SIZES AS GIVEN BELOW UPTO 0.60 METRE AVERAGE DEPTH in cement Mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation Cement mortar 1:2:4 BENCHING 12 mm THICK CEMENT PLASTER 1:2 with a floating coat of 1 mm thick of neat cement R.C.C 1:2:4 SLAB 100 mm THICK/CC/ TOPPING 50 mm THICK WITH 455 MM x 455 MM X 610MM INSIDE LIGHT DUTY C.I. INSPECTION CHAMBER COVER AND FRAME Weight as per I.SI. specification painted WITH 3 COATS OF black bitumastic superior paint complete as per standard design. (HSR 29.84 a) Size 450 mm x 450 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 40 kg with C.C. topping )

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE EUROPEAN TYPE WATERCLOSET SUITE WITH CONCEALED ‘P’ or ‘S’ TRAP with or without vent (as approved by the Engineer-in-charge) and all other necessary fittings as fully described in item no. 30.3 above (ii) Single Colour (HSR 30.6 ii)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE LARGE FLAT BACK or Angular lipped from Urinal 610 MM HIGH consisting of 5 LITRES CAPACITY mosquito proof INDIAN MAKE C.I AUTOMATIC flushing CISTERN painted with non- Yellowing white enamel paint or other approved shade Enamel paint on outside and superior black britumastic Paint on inside with screwed 15 mm pipe (HSR 30.25 ii)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE LAVATORY SUITES (WITH ANTI SPLASH RIM IN VITREOUS CHINAWARE and all other necessary fittings as fully described in item no. 30.41 above. (HSR 30.42(vi) Size 690 mm x 550 mm with one no. trap

Providing and fixing in position best Indian make Pedestal fittings of vitreous chinaware complete (as required by the Engineer-in-charge) (ii) Single Colour (HSR 30.44 ii)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawlslugs embedded in walls with C.P brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.68 (a) (ii) a)25 MM DIA C.P BRASS ADJUSTABLE (ii) 600 mm long.

Providing and fixing in position 15 mm i/d C.P brass bib Cocks of best quality (as required by Engineer-in-charge) (a) Bib cock long body (HSR 30.75 a)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRRON Mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.71 (1) INDIAN MAKE (I) 600 mm x 450 mm

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE C.P BRASS WALL MIXER 15 MM (HSR 30.81 (b) Without Telephonic shower

PROVIDING AND FIXING IN POSITION H.C.I SOIL WASTE VENT OR ANTISYPHONAGE PIPES TO I.S.I SPECIFICATION OF E.L.C. MANUFACTURE OR OF ANY OTHER REPUTED FIRM INCLUDING CUTTING AND WASTAGE ETC AND CUTTING HOLES IN WALLS, ROOFS OR FLOOR ETC ANDMAKING GOOD to its original condition BUT EXCLUDING COST OF LEAD JOINTING. (a ) 100 mm internal diameter. (HSR 30.84 a)

PROVIDING AND FIXING IN POSITION C.I GULLY TRAP COVER WEIGHING APPROXIMATELY 7.26 KG AND FRAME FOR GULLY TRAP CHAMBER CLEAR OPENING SIZE 300 MM X 300 MM AND OUTSIDE SIZE 330 MM X 330 MM INCLUDING PAINTING THE EXPOSED SURFACES WITH 3 COATS of black bitumastic Superior paint of approved manufacture etc. (HSR 30.85)

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K. make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. (except civil work).(HSR 30.119 e) 1000 Ltr. Capacity (HSR 30.119)

LABOUR FOR LAYING JOINTING, FIXING AND TESTING G.I/P.V.C/W.I PIPE LINES AND SPECIALS tees bends, Sockets elbows etc., INSIDE BUILDING and testing etc., complete including cutting threading (NS Item) (i) 15 mm internal diameter of pipeline

(ii) 20 mm internal diameter of pipeline

HARISH KUMAR CONTRACTOR