REPAIR/MAINT TO RTC BLDG AND SUBMERSIBLE PUMP, EXT WATER SUPPLY AND OTHER CONNECTED WORKS AT PRAVUDH VIHAR (PCDA), DEVI KHERA, BASE HOSP, SOI, PD AUDITORIUM, SURYA AUDITORIUM IN THE AREA OF AGE E/M (HOSP) UNDER GE E/M LUCKNOW

Amount

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified & directed by EIC.

All as per item No 1 above but on ceiling.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint/shade complete all as specified & directed by EIC.

All as per item No 3 above but two coats

All as per item No 3 above but on ceiling.

Preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified & directed by EIC.

Preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified & directed by EIC.

Complete removal of existing treatment of walls and applying two coats of distemper oil emulsion over and including a coat of primer over and including a thin layer of wall care putty on old plastered surfaces including prepration complete all as specified & directed by EIC.

Taking down cement plaster on brick wall, racking out joints hacking for key scrubbing down with water complete all as specified & directed by EIC.

M&L for rendering 10 mm thick on brick work/ concrete surfaces in cement mortar 1:6 on fair faces finished fair & even without using extra cement complete all as specified & directed by EIC.

M&L rendering 5 mm thick on concrete surfaces in ceiling , in cement and sand mortar 1:3 complete all as specified & directed by EIC.

M&L for preparing surfaces, plastered or unplastered new surfaces of ceiling and applying three coats white wash complete all as specified & directed by EIC.

Preparation of newly plastered surfaces and applying two coat of oil bound disemper over one coat of oil base primer all as specified on walls surface over and including a thin layer of wall care putty complete all as specified & directed by EIC.

M&L applying one coats of plastic emulsion paint interior quality any shade over old painted surface including preparation of wall surface complete all as specified and directed by EIC.

S&F Mild Steel work as in angle iron fencing posts struts including cutting,tops to shape as directed bent to shape, drilling holes, notching for wire etc including all necessary bolting or riveting etc. Including securing chain link fencing vertically with angle iron and flat iron etc complete all as specified & directed by EIC.

S&F 10mm dia mild Steel screw bolts(machine made) with hexagonal or square head at one end and screw the other or screwed both ends(as directed) each screwed end to be fitted with washer and one hexagonal or square nut not exc. 5 cm long complete all as specified & directed by EIC.

Supply only Chain link fencing MS galvanised fencing of any size complete all as specified & directed by EIC.

Fixing only Chain link fencing including line wires, any mesh size and type to any type of standards, rails, strainning bolts etc.including provn of binding wire complete all as specified & directed by EIC.

M&L for preparation of new steel and Iron surface of width or girth exc. 10 cm and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified & directed by EIC.

Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each complete all as specified & directed by EIC.

Taking down chowkhats or frames (wooden/aluminium) with shutters without taking off shutter from the frames exc. 1.5 but n. exc 4 sqm each complete all as specified & directed by EIC.

Factory made solid panel PVC Door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail,lock rail and bottom rail on either side as gap insert for top rails, bottom rail,panelling of plain colour PVC sheet to be fitting in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supply & fixing in the frame at site as per specification and drawing on Page No 156 of SSR Part-II Rates,complete all as specified and directed by the Engineer in Charge.

Factory made flush shutters 35 mm thick, solid core construction , with block board core and plywood face panels, commercial type on both sides , complete all as specified and directed by the Engineer in Charge.

S&F 100 mm size butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B21 complete all as specified and directed by the Engineer in Charge.

S&F 250 mm aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed by the Engineer in Charge.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed by the Engineer in Charge.

S&F 125 mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by the Engineer in Charge.

M&L for preparing of new previously untreated surfaces of wood or wood based material over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by the Engineer in Charge.

Aluminium Anodised door frame with shutter, including necessary joining cleats, glazing clips rubber neoprene packing , Handle 2 Nos in each door, 4 Nos 100mm hinges, 1 Nos 200mm aluminium anodised tower bolt anodised aluminium snap beading screw ecessary locking arrangement with mortice lock with duplicate , complete all as specified and directed by Engineer -in-charge.

Sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane, including Hacking out old broken glass panes of any thickness, size ,quality or description from wooden frames , glazed with putty or fixed with beads ,complete all as specified and directed by Engineer-in- Charge.

Figured glass 3 mm thick, ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane, including Hacking out old broken glass panes of any thickness, size ,quality or description from wooden frames , glazed with putty or fixed with beads ,complete all as specified and directed by Engineer-in- Charge.

Sheet glass 4.8 mm thick, ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane, glazed with putty or fixed with beads, including Hacking out old broken glass panes of any thickness, size ,quality or description from wooden frames , glazed with putty or fixed with beads ,complete all as specified and directed by Engineer-in- Charge

Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. .(Minimum weight 20mm-210gms) fixed as repair in PVC OHT tanks ,complete all as specified and directed by Engineer-in- Charge.

Repairing of existing aluminium door single leaf including oiling and greasing of floor springs and making the door and shutter serviceable , complete all as specified and directed by Engineer -in-charge. Note: Floor door springs where renewed shall be measured and paid separately under appropriate items.

Chromium plated fancy long body Bib taps with cup , cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule fixed as in repair , complete all as specified and directed by the Engineer in -Charge

Aluminium Anodised window, ventilator fixed type shutter, aluminium section weighing 0.55 Kg/m incl necessary joining cleats, glazing clips rubber neoprene packing , Handle 2 Nos in each door, hinges, anodised aluminium snap beading screw ,complete all as specified and directed by Engineer -in-charge.

Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without lettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe fixed as in repair , complete all as specified and directed by the Engineer in -Charge

Taking down carefully old switch steel boxes (light, fan, socket or power) complete, including laminated sheet , switches, regulators sockets etc. and making good the disturbed surfaces of walls, floors etc and match with the existing colour of wall complete all as specified and directed by the Engineer in Charge.

Switch modulor type, single pole, one way 6 Amp 230 Volt complete all as specified and directed by the Engineer in Charge.

Switch Modulor type, single pole, one way 16 Amp 230volt complete all as specified and directed by the Engineer in Charge.

S/F socket outlet modulor type 6 Amp 230volts complete all as specified and directed by the Engineer in Charge.

S/F socket outlet modulor type 16 Amp 230volts complete all as specified and directed by the Engineer in Charge.

S/F Electronic type modulor fan regulator step type 120 Watts complete all as specified and directed by the Engineer in Charge.

Supply and fixing in replacement LED bulb 10 watt screw type AC 230 volt 50 hz complete all as specified and directed by the Engineer in Charge.

Supply and fixing switch piano flush button single pole one way 6 amps, 230 Volts complete all as specified and directed by the Engineer in Charge.

Supply and fixing socket outlet flush type 6 Amps, 5 pin, 230 Volts flush type complete all as specified and directed by the Engineer in Charge.

Supply and fixing switch piano flush button single pole one way 16 Amp 240 volt complete all as specified and directed by the Engineer in Charge.

Supply and fixing socket outlet multipurpose 6 pin, 16 amps flush type complete all as specified and directed by the Engineer in Charge.

Supply and fixing modular fan regulator 100 Watt complete all as specified and directed by the Engineer in Charge.

Point wiring for one light/fan point controlled by one, one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly and make wall surface as existing same colour in and including taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing,complete all as specified and directed by Engineer-in- Charge.

Point wiring for one socket outlet point 5 amps on independent board controlled by one, one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly in and including taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing ,complete all as specified and directed by Engineer-in- Charge.

All as per item no 52 hereinbefore but one socket outlet point on same baord with other switches with 1.5 sq mm single core multistranded PVC insulated FRLS cable including 1.5 sq mm single core multi stranded copper cable used as continuous earth wire ,complete all as specified and directed by Engineer-in- Charge.

Point wiring for 15 amps socket point controlled by one, one way switch using 2.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated FRLS unsheathed cables in and including PVC concealed conduit and conduit fittings including pressed steel terminal switch boxes and 3 mm thick plate for fixing of switches/sockets and fitted with Chromium plated brass screws & washers and1.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated unsheathed earth wire and connected to earth dolly in and including taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing ,complete all as specified and directed by Engineer-in- Charge.

Sub main wiring (concealed type ) with two single core 6 Sqmm FRLS PVC insulated and unsheathed 1100 volts grade cables with stranded copper conductor cable drawn through in and including 25 mm dia rigid non metallic PVC conduit and conduit accessories including one single core 4 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dully complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface, as in replacement complete all as specified and directed by Engineer-in-Charge. Note : (i) 2 run of 6 Sqmm ,1 run of PVC conduit & 1 run of 4 Sqmm cable will be measured as single run. (ii) Extra length of cables/wire required for connection to MCBs shall not be measured and paid separetly the rate quoted by contractor per unit shall be deemed to be included in the quoted rate of this item.

Supply and fixing MCB SPN 240 Volts, 32 to 63 amps 10 KA ,c-series including connection with suitable size aluminium / copper lugs as in replacement complete all as specified and directed by the Engineer in Charge.

Supply and fixing LED tube (Tube rode) LED 18/20W Retro Bar Professional WH 5700K/CW 6500K as in replacement complete all as specified and directed by the Engineer in Charge.

Supply & fix of energy saving ceiling fan 1200 mm sweep ,220-240 volts AC, 50 Hz, ISI marked with five star rating including hanging with the help of fan hook,down rod up to 4 feet and connecting up with complete with electronic type regulator and accessories , single phase including making connection with three core PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing complete all as specified and directed by the Engineer in Charge. . Note: Old Ceiling fan handover MES Store. Make:Havells Fusion Five Star 1200mm Ceiling Fan (Pearl and Ivory) Bajaj/ CG .

Supply and fixing cable 2 x 4.0 sqmm single core, copper, multistranded, PVC insulated, unsheathed, 1100 volts with 1 x 4 sqmm earth wire grade as in replacement complete all as specified and directed by the Engineer in Charge.

Supply and fixing heating element 1.5 KW (ISI marked) suitable for geyser of 25 litres capacity, horizontal or vertical type any make as in replacement complete all as specified and directed by the Engineer in Charge.

Supply and fixing heating element 2 KW (ISI marked) suitable for geyser of 50 litres capacity, horizontal or vertical type any make as in replacement complete all as specified and directed by the Engineer in Charge.

Supplying and fixing bollard lights 40 watt LED type AC 230 volt 50 HZ including excavation , foundation and cement work as in replacement complete all as specified and directed by the Engineer in Charge.

Supplying and fixing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 Sqmm 3.5 core Ac 230 volt 50 hz as in replacement complete all as specified and directed by the Engineer in Charge.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces foundation, manholes etc to required levels in soft/loose soil , complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each, excavated soil in trenches after the cables have been laid and tested, complete all as specified and directed by Engineer-in-Charge.

Removing excavated soil to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.50 meter above the starting point , complete all as specified and directed by Engineer-in-Charge.

M&L for sand filling in trenches including spreading and leveling for cushioning of under ground cables complete all as specified and directed by Engineer-in-Charge.

M&L for bricks sub-class 'B' (old size), laid flat in trenches for cable protection complete all as specified and directed by Engineer-in-Charge.

Supply and lay cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sq mm 2 core as in replacement complete all as specified and directed by Engineer-in-Charge.

General servicing of Kirloskar Make DG set including tappet adjustment of 125 KVA sets including supply and replacement of tappet cover gasket complete all as specified and directed by Engineer-in-Charge.

Supply and replacement of diesel filter Primery and secondary .

Supply and replacement of Lub Oil filter

Supply and replacement of radiator hose pipe Set

Supply and replacement of Fan belt

Supply and replacement of fuel/lub oil pipe flexible.

Supply and replacement of Lub oil filter cartridge

Supply and replacement of Air cleaner Element

Supply and replacement of Hose pipe for Air cleaner

Supply and replacement of Hose thermostat by pass

Supply and replacement of Hose water pump to radiator

Supply and replacement of Hose water pump inlet to radiator

Supply and replacement of Hose make up tank

Disconnecting of oil chamber and decaning of old lub oil from all sets . Supply and filling the new oil 20W/40W all as per manufacturer's recommendation up to required level complete all as specified and directed by Engineer-in-Charge.

Supply and fixing (in repairs ) sealed bettery maintenance free, 12V 180 AH including initial charging complete complete all as specified and directed by Engineer-in-Charge.

M & L for cleaning of all condenser tubes of central AC plant by disconnecting the condenser from the system, cleaning by decaling pump of suitable capacity of 110 ft head using decaling solution of Make ;- MAIC / HIBIRD or Hydrochloric acid 20%, cleaning the system through cooling tower by using decaling solution, cleaning condenser tubes by nylon brushes & mild steel rods of suitable size renewal of suction water filter for the following AC Plants complete all as specified and directed by Engineer-in-Charge. (Note ;- T & P such as pumps, tube etc & decaling solution etc. shall be arranged by the contractor at his own cost). 1 X 10 TR capacity AC plant

Carrying out pressure leak testing by nitrogen gas of the system of AC plant for leak proof valve joints, seal & other connected controls etc. including identifying & rectifying of leaks, defects (if any) & maintaining constant pressure of 160 LBS PSI on low side & 200 LBS PSI on high side at least for 24 Hrs complete all as specified and directed by EIC. for the following AC plant complete all as specified and directed by Engineer-in-Charge. (Note :- the arrangement of T&P & nitrogen gas shall be contractors responsibility). 1 X 10 TR capacity AC plant

Taking out defective hand shut off valve of pressure gauge and supply & fixing new hand shut off valve 1/4" dia complete all as specified and directed by Engineer-in-Charge.

Taking out carefully nitrogen gas (residual) after flushing, pressure testing & vaccumising the whole AC Plant with the help of vacuum pump & leaving the plant for 24 hrs for checking the leak point and commissioning the plant by charging refrigerant gas complete all as specified and directed by Engineer-in-Charge. (Note :- (i) Arrangement of vaccum pump shall be the contractor responsibility (ii) Refrigerant gas for charging shall be issued under relevent items). 1 X 10 TR capacity AC plant

Taking out carefully used compressor oil from AC plant and filling fresh compressor oil into the Plant complete all as specified and directed by Engineer-in-Charge. (Note :- (i) Old compressor oil shall be the property of contractor and amount of credit shall be recovered & new compressor oil shall be issued by the contractor and paid separately). 1 X 10 TR capacity AC plant

Taking out unserviceable / defective finned strip heater and supply and fixing new strip heater suitable for AC plant capacity 3.0 KW including provision of nuts, bolts, & washers etc. complete all as specified and directed by Engineer-in-Charge.

Taking out the existing unserviceable low / high pressure cut-out switch and supply & fixing new low / high pressure cut-out switch type MP - 15 complete all as specified and directed by Engineer-in-Charge.

M&L for replacement of condenser safety valve of the ½" size to with stand the pressure up to 300 PSI complete all as specified and directed by Engineer-in-Charge. (Make ;- PIM/BAP).

All as per Item No 92 above but 3/8" Size

Taking out the existing defective pilot control solenoid valve and supply & fixing new pilot control solenoid valve complete all as specified and directed by Engineer-in-Charge. (Make :- Sporlain / Sunlan).

M&L for repair to liquid & oil equalizer valve of compressor by replacing the Teflon sheet & spindle and changing Neoprene 'O' ring complete all as specified and directed by Engineer-in-Charge.

Dismantling defective GM gate valve 20 mm Dia at drain pipe of cooling tower of AC plant and supply and fixing new GM gate valve 15 mm Dia with GI Nipple, bends etc nuts & bolts and necessary electric welding complete all as specified and directed by Engineer-in-Charge.

Dismantling and removing defective Finns of FRP type cooling tower and supply and fixing new PVC Finns brick containing eleven layers size of brick 600 x 30 x 150 mm complete all as specified and directed by Engineer-in-Charge.

Taking down the existing defective discharge gauge and supply & fixing new discharge gauge pressure gauge 4" Dia (-) 30 to 0 & 0 - 300 PSI complete complete all as specified and directed by Engineer-in-Charge. (Make :- Fiebig/Guru).

Taking out wire mesh filter from AHUs cleaning the same with castic soda and water with pump pressure and reassembling in their position complete all as specified and directed by Engineer-in-Charge. (Note:- cleaning to be done three times in a season).

Taking out defective / burnt power contactor from electric panel board and S&F in replacement new power contactor complete all as specified and directed by Engineer-in-Charge.

Taking out defective / burnt power contactor from electric panel board and S&F in replacement new power contactor complete all as specified and directed by Engineer-in-Charge.

Taking out defective / burnt bimetal relays from LT panel board and supply and fixing new bimetal relays 3 UA 50 range 32 - 50 and 40 - 57 Amps in position complete all as specified and directed by Engineer-in-Charge.

Taking out carefully electronic timer defective in panel board and supply and fixing new electronic timer cat No. 800-S/7PU rating 30 to 0/60 to 20 in position complete all as specified and directed by Engineer-in-Charge.

Taking out carefully defective/burnt single phase preventor complete with wiring from LT panel and supply & fixing in replacement in position single preventer complete with wiring complete all as specified and directed by Engineer-in-Charge.

Taking out carefully defective / burnt power contactor type ML-1 from the LT panel board and supply & fixing new in position in replacement power contractor ML-1 complete all as specified and directed by Engineer-in-Charge.

Disconnecting electrically unserviceable CT fan motor and Supply installation testing and commissioning of CT fan motor complete with other accessories like fan blades etc. 3 phase, 415 Volts,3 HP capacity complete all as specified and directed by Engineer-in-Charge.

S&F LED street light 60 Watt made of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection fixed on street light pole complete all as specified and directed by Engineer-in-Charge.

Supply and fixing vertical type DB double door fitted with standard 100 Amp, 4 pole isolator as incomer without MCBs, 8 way for 430 Volt, 3 phase complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sheet metal enclosure MCB TPN DB double door suitable for distribution boards when MCB to be used having 200 Amp rated bus bar triple pole and neutral 12 ways 430 Volt complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sheet metal enclosure SPN DB 240 Volt double door suitable for distribution boards when MCB to be used having 200 Amp rated bus bar single pole and neutral 4 ways 240 Volt complete all as specified and directed by Engineer-in-Charge.

Supply & fixing exhaust fan 300 mm sweep AC 230 volts single phase with louvers including making connection with three core PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing complete all as specified and directed by Engineer-in-Charge. Note: Old Ex-fan handover MES Store.

Supply and fixing sheet metal enclosure SPN DB 240 Volt double door suitable for distribution boards when MCB to be used having 200 Amp rated bus bar single pole and neutral 8 ways 240 Volt complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB SP 240 Volts, 6 to 32 amps 10 KA ,c-series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engineer-in-Charge.

S & F MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 25 KA complete all as specified and directed by Engineer-in-Charge.

S & F MCCB 4 Pole, 415 V, Adjustable type, 200 Amps with breaking capacity 25 KA complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of thermal over load relay with arm contact for DOL starter 3 Phase 415 volts ranging 4-6 Amps complete all as specified and directed by Engineer-in-Charge..

Overhauling, Oiling, Greasing and servicing of Air blower of any capacity by Opening of all parts , suction air filter ,bush ,bearing , rotor ,drum , bearing of motor shaft ,Neck ring, coupling with studs between motor & air blower ,& all other parts and re-assemble the same after greasing , oiling , complete all as specified and directed by Engineer-in -charge. NOTES : - (i) Overhauling and servicing of Air blower should be carried out by Auth company or dealer Which is specialist of above . (ii) Spares/parts renewed shall be measured and paid separately under appropriate items as supply only.

Taking out /dismantling of Air blower pump set of rating 3 phase 440 Volts supply of capacity upto12.5 HP from STP plant at any location and shifting the same to contractor's workshop for repair and re-installation/refixing the same at its original site and testing , complete all as specified and directed by Engineer-in -Charge. NOTES :- (i) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against this item and nothing extra shall be admisible on this account. (ii) Labour for assembling of old/serviceable and new parts to make the Air blower in serviceable condition shall be included under appropriate item here in after. (iii) Spare/parts renewed shall be measured and paid separately under appropriate items here in after.

Cutting out the existing winding of the motor, opening of winding, and rewinding with super enamelled copper winding wire of best quality of existing size/gauge and weight including replacement of insulation material, varnish, bearing, connection plate and all other petty items required to make motor functional and re-assembling the motor including installation commission and testing on full load , complete all as specified and directed by Engineer-in -Charge. Note :Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit. Make of winding wire :DEVI DAYAL/ HTP/ CHETAK or any other equivalent make as approved by GE/Engineer-in -Charge.

Repairing of pump by re-threading of worn out studs holes and supply and fixing over size studs with nut and washer, complete all as specified and directed by Engineer-in -Charge.

Repairing of pump shaft by depositing metal on it by breazing, grinding and polishing to appropriate size of the shaft, complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of gun metal/stainless steel bush of pump shaft, complete all as specified and directed by Engineer-in - Charge.

Supply and fixing of driven end bearing of blower shaft , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of end bearing of blower shaft , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of gland and packing , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of coupling with studs between motor & air blower , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of suction air filter, complete all as specified and directed by Engineer-in -charge.

Supply and fixing of suction silencer, complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Neck ring, complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of bearing of motor shaft, complete all as specified and directed by Engineer-in -Charge.

Taking out /dismantling of Air blower pump set of rating 3 phase 440 Volts supply of capacity upto 7.5 HP from STP plant at any location and shifting the same to contractor's workshop for repair and re-installation/refixing the same at its original site and testing ,complete all as specified and directed by Engineer-in -Charge. NOTES :- (i) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against this item and nothing extra shall be admisible on this account. (ii) Labour for assembling of old/serviceable and new parts to make the Air blower in serviceable condition shall be included under appropriate item here in after. (iii) Spare/parts renewed shall be measured and paid separately under appropriate items here in after.

Cutting out the existing winding of the motor, opening of winding, and rewinding with super enamelled water proof copper winding wire of best quality of existing size/gauge and weight including replacement of insulation material, varnish, bearing, connection plate and all other petty items required to make motor functional and re-assembling the motor including installation commission and testing on full load , complete all as specified and directed by Engineer-in -Charge. Note :Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit. Make of winding wire :DEVI DAYAL/ HTP/ CHETAK or any other equivalent make as approved by GE/Engineer-in -Charge.

Taking out /dismantling of Air blower pump set of rating 3 phase 440 Volts supply of capacity upto 5 HP from STP plant at any location and shifting the same to contractor's workshop for repair and re-installation/refixing the same at its original site and testing ,complete all as specified and directed by Engineer-in -Charge. NOTES :- (i) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (ii) Labour for assembling of old/serviceable and new parts to make the Air blower in serviceable condition shall be included under appropriate item. (iii) Spare/parts renewed shall be measured and paid separately under appropriate items.

Cutting out the existing winding of the motor, opening of winding, and rewinding with super enamelled copper winding wire of best quality of existing size/gauge and weight including replacement of insulation material, varnish, bearing, connection plate and all other petty items required to make motor functional and re-assembling the motor including installation commission and testing on full load , complete all as specified and directed by Engineer-in -Charge. Note :Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit. Make of winding wire :DEVI DAYAL/ HTP/ CHETAK or any other equivalent make as approved by GE/Engineer-in -Charge.

Taking out unserviceable non clog submersible type raw effluent sewage lifting Submersible pump set of capacity upto 10 HP of rating 3 phase 440 Volts, from raw sewage collection sump/well of STP plant well upto 18 metre depth at any location in cantt area lucknow ,for cleaning of muds , overhauling, Oiling,Greasing and servicing by Opening of all parts , bush ,bearing , rotor ,drum , bearing of motor shaft ,Neck ring, coupling with studs between motor & all other parts and re-assemble the same after greasing , oiling of and shifting the same to authorised workshop for repair , testing and re-installation/Re-fixing/lowering in the sewage sump , complete all as specified and directed by Engineer-in -Charge. Notes : - (i) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against this item and nothing extra shall be admisible on this account. (ii) Parts renewed shall be measured and paid separately under appropriate items here in after. (iii) Overhauling and servicing of non clog submersible Pump should be carried out by Auth company or dealer Which is specialist of above here in after.

Attend the day to day complaint of non functing part to Air Blower , Air Blower Motor ,non clog submersible Pump, motor ,MCB DB ,Panel Board , DG set ,Electric cable ,Switch socket & other Electric connection of any size ,type ,capacity and all connected parts , complete all as specified and directed by Engineer-in -Charge. Notes : (i) Parts renewed shall be measured and paid separately under appropriate items. (ii) Complaint Should be attend immediately within two hrs & Rectified the same day at the earliest without effecting of service .

Attend the day to day sewage complaint related leakege , choke , replacement of any part , with cutting ,jointing and any other work of GI Pipe ,MS Pipe , PVC Pipe for any size ,type ,capacity and any location rectified the same , complete all as specified and directed by Engineer-in -Charge. Notes : (i) Parts renewed shall be measured and paid separately under appropriate items. (ii) Complaint Should be attend immediately within two hrs & Rectified the same day at the earliest without effecting of service .

Taking out the silt & foreign object , cleaning & removing sludge from course bar screen including all chamber of equilasation tank upto depth of 15 Metre of any capacity of STP, complete all as specified and directed by Engineer-in -Charge.

Taking out the silt & foreign object , cleaning & removing sludge from Fine bar screen oil & grease Chamber with water pressure, bleaching powder etc, complete all as specified and directed by Engineer-in -Charge.

Taking out the silt & foreign object , cleaning & removing sludge from MBBR I & II Chamber with water pressure, bleaching powder etc , complete all as specified and directed by Engineer-in -Charge.

Taking out the silt & foreign object , cleaning & removing sludge from Tube Setteler Chamber with water pressure, bleaching powder etc , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Plastic Media MBBR (Media) as per existing size & specification as per IS fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Bubble diffuser as per existing size & specification fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Pac media in tube settler tank as per existing size & specification fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Sand filter media of sludge drying bed as per existing size & specification fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Distribution box at equilistion well as per existing size & specification fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of MS gate of oil & Greece chamber as per existing size thickness & specification fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of MS gate of sludge drying bed as per existing size thickness & specification fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Preparation of old painted surface of old M S pipe/angles of any description in any width or girth for complete one STP and painting with applying two coats of epoxy paint over and including one coat of primer , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Pressure gauge o to 7 Kg/cm2 as per existing size & specification fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Taking out unserviceable/burnt raw non clog submersible type raw effluent sewage lifting Submersible pump set of capacity upto 10 HP of rating 3 phase 440 Volts supply from raw sewage collection sump of STP plant at any location and shifting the same to authorised workshop for repair and re-installation/Re-fixing/lowering in the sewage sump , complete all as specified and directed by Engineer-in -Charge. NOTES :- (i) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against this item and nothing extra shall be admisible on this account. (ii) Labour for assembling of old/serviceable and new parts to make the Submersible pump set in serviceable condition shall be included under appropriate item. (iii) Spare/parts renewed shall be measured and paid separately under appropriate items here in after.

Cutting out the existing winding of stator of submersible motor of any make and rewinding with super enamelled water proof copper winding wire of best quality of existing size/gauge and weight including replacement of insulation material, varnish, bearing, connection plate and all other petty items required to make motor functional and re-assembling the motor including installation commission and testing on full load , complete all as specified and directed by Engineer-in -Charge. Note :Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit. Make of winding wire :DEVI DAYAL/ HTP/ CHETAK or any other equivalent make as approved by GE/Engineer-in -Charge.

Straightening of the slots of stator of submersible motor of any make, complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of thrust bearing block of submersible pump of any make , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of gun metal bushes for submersible motor as per manufacturer's design and specification , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of sand guard of submersible motor, complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of bronze metal impellars, complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of shaft sleeve, complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of set of gasket and O-ring , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Mechanical seal motor end , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Mechanical seal pump end, complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of deep groove ball bearing motor side, complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of groove ball bearing pump side , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of pump casing , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of intermediate casing , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of bearing housing , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of bearing cover , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of shaft protection sleeve , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of bowl cast iron , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of complete bearing sleeve , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of rotor , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of cable assembly , complete all as specified and directed by Engineer-in -Charge.

Supply & filling of new Gear Oil Grade G-90 for Air Blower , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of air blower pulley as per sample fixed as in replacment, complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Bi-metallic overload relay with single phasing protection of range 2.5 to 4 Amps fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Digital Ampere meter ISI Marked suitable for (0-400Amps) range three phase AC Supply, current ratio 150/5A fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Supply and fixing of Voltmeter moving coil type suitable for voltage range 0-500 Volts for three phase AC system fixed as in replacment , complete all as specified and directed by Engineer-in -Charge.

Earthing complete with galvanised steel plate earth electrode 600X600X6mm thick buried directly in ground (earth pit not less than 2.25 meter below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to GI strip 32x6mm at two points by means of bolts and nut, check nut and washers including charcoal dust, common salt, necessary excavation in hard/dense soil, returning filling in and removal of surplus soil to a distance up to 50metres, PCC pit in 1:3:6 type CI (using 20mm grade stone aggregate) RCC 1:2:4 type B-1 (using 20mm grade stone aggregate ) 50mm thick pit cover, reinforced with 8mm dia TMT bars 75mm c/c, both ways MS handle 12mm dia, GI funnel, wire mesh and GI watering pipe of 20mm bore GI (light grade) and earth lead protection pipe 40mm bore (light grade) all as specified, directed and shown in electrical plate No 5 of SSR Part-I and testing ,including replacment of old unserviceable earthing, complete all as specified and as directed by Engineer-in-Charge. Note : (i) The unit rate includes earth lead and protection pipe up to maximum 7.5 metre from earth plate to earth point/test point. (ii) Earth pit shall be constructed minimum 1.00 metre away from earth.

Construction of valves pit chamber of size 900x900x900mm (internal dimension), using PCC (1:4:8) 40 mm graded stone aggregate for foundation 15 cm thick, 23 cm thick wall in CM (1:4) 10 mm thick rendering all around the brick work with 1:6 cement mortar PCC (1:2:4) type B1 coping with 20 mm graded agregate for grouting MS frame including 4 mm thick MS top sheet cover with locking arrangement including 50 mm pad lock with double key arrangement, MS frame out of 40 x 40 x 5 mm thick angle iron including paintaing of steel surface with two coats of synthetic enamel paint over a coat of red oxide primers finishing coat including necessary excavation in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs ,complete all as specified and directed by Engineer-in-Charge.

As per item No 180 above but 1050 mm x 1050 mm x1050 mm

As per item No 180 above but size 1200 mm x 1200 mm x 1200 mm

Supply and fixing of pressure guage analog type suitable for pressure range 0 to 10 Kg/Cm2 fixed as in repair ,complete all as specified and directed by the Engineer-in-Charge.

Preparation of old painted surface of existing exposed iron surfaces/pipes/iron gate etc of any description in any width or girth and painting with synthetic enamel paint (colour to be decided by EIC) over a coat of red oxide primer , complete all as specified and directed by Engineer-in -Charge.

Supply only Calcium Hypochlorite having 65 % - 70 % available chlorine packed in 45 Kgs plastic drums for treatment chemical each , complete all as specified and directed by Engineer-in -Charge. NOTES :- (i) Approval of chemical (calcium hypochlorite) shall be given after verifaction of test certificates of chemical of various manufactures and other factores like chemical and safety and health hazard aspects of usage of chlorination (ii) The brand / make of the chlorination of chemical must be stated in production and certified by govt laboratory confirming compliance of specification suitable for drinking water with a declearation from the laboratory that from the technical strengh stability health safety and operation point of view this product is used for drinking water applications for consumption by humans and the brand/make of calcium hypochlorite is suitable for drinking water chlorination and its sample has been tested by Govt Laboratory.

Provision for Bectroligical test and sample collection from Four STP plant in sterlized bottle by UP Pollution Control Board ,monthly periodically as per the enviroment ( Protection ) Rull Sch II ( Rule 3 ) 1986 , in permission standard in Sewage Treated Water for inland surface water i.e , complete all as specified and directed by Engineer-in -Charge. Contractor has to maintain the quality of water as below mentioned parameters: (a) Suspended solid Max < 50 mg / Ltrs . (b) Dissolved Solids max in - organic < 2100 mg /a , (c) PH value (6.5 to 9.0 PH ) (d) Biochemical oxygen Demand ( 5 days at 20 ^ degree cetigrate ) Max < 20 (e) COD ( Chemical Oxygen Demand ) up to 50 mg / l . (f) Total coliform in MPN as per standard Norms (g) Focal Coliform in MPN as per standard norms. NOTE:- Testing report for 04 no of STP for Raw sewage and after treatment water monthly wise on last week of each month will be included in quotaed rate .The contractor responsibilty to maintain test parameter as per standard norm planned sewage plant maintanance time to time fpr proper functioniong.

M & L for Lifting /Lowering of the pumping motor 7.5 Hp tor, cable,column pipe and other connected accessories including making all electrical connection, commission & testing complete all as specified and directed by Engineer-in-Charge.. Note- All T & P, manpower are arrnage by contractor and included cost in quated rate.

Dismantling and taking out burnout winding of the motor up to 10 HP capicity and rewinding with 100 % copper wiring as replacement the quality of capicity 10 HP including connection commissioning & testing after fixing in bore well complete all as specified and directed by Engineer-in-Charge.

Supply and laying in replacement flexible flat PVC insulated PVC sheathed copper couductor stranded submersible cable cores 1100 volt grade 16 Sqmm 3 core including jointing material and connection work complete all as specified and directed by Engineer-in-Charge.

S&F round strand steel wire rope RHO/LHO/RHL/LHL conforming to IS: 2266/02 dia 12 mm 1770 N/mm² tensile and connected clamp nut bolts fixed complete all as specified and directed by Engineer-in-Charge. Make: BWR or equivalent make as approved by GE.

M & L for Submersible pump Fully Automatic Star delta Starter In sheet Enclosure Type MU-G Motor rating AC-3,Duty 415v, 50 Hz 3 Phase to 30 HP,Relay range of 30-50 A as per existing after taking out old unservicable one complete all as specified and directed by Engineer-in-Charge.

M & L for Timer Star Delta time of 3 sec-30 sec Voltage range 240-415V AC. Contact arrangement 1 C/O (Star)+1 C/O (Delta) as per existing after taking out old unservicable one complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections , including removal of 15 mm bore complete all as specified and directed by Engineer-in-Charge.

As per item No 193 above but 20 mm bore

As per item No 193 above but 25 mm bore

As per item No 193 above but 40 mm bore

As per item No 193 above but 50 mm bore

As per item No 193 above but 80 mm bore

As per item No 193 above but 100 mm bore

Refixing old steel tubing and connecting in new or old position (wall,ceiling,floors etc) 15 mm bore complete all as specified and directed by Engineer-in-Charge.

As per item No 200 above but 20 mm bore

As per item No 200 above but 25 mm bore

As per item No 200 above but 40 mm bore

As per item No 200 above but 50 mm bore

As per item No 200 above but 80 mm bore

As per item No 200 above but 100 mm bore

Supplying, laying, jointing and testing 15 mm bore galvanised water tubing, medium grade, with all GI fittings , and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

As per item No 207 above but 20 mm bore

As per item No 207 above but 25 mm bore

Supplying, laying, jointing and testing 15 mm bore galvanised water tubing, medium grade, with all GI fittings and laid in trenches complete all as specified and directed by Engineer-in-Charge. (Excavation & earthwork shall be measured & paid separately under appropriate item)

As per item No 210 above but 20 mm bore

As per item No 210 above but 25 mm bore

As per item No 210 above but 40 mm bore

As per item No 210 above but 50 mm bore

As per item No 210 above but 80 mm bore

As per item No 210 above but 100 mm bore

Taking up worn out cast iron water mains 80 mm bore (including all fittings) with spigot & socketed ends and lead joints including burning out joints and recovering lead complete all as specified and directed by Engineer-in-Charge.

As per item No 217 above but 100 mm bore

As per item No 217 above but 150 mm bore

Suplying, laying, testing 80 mm bore Cast iron pipes with flanged ends, centrifugally cast, class A, in any length laid in trenches of following bore of pipe complete all as specified and directed by Engineer-in-Charge.

As per item No 220 above but 100 mm bore

As per item No 220 above but 150 mm bore

M&L joint with rubber or fibre board gasket 80 mm bore for flanged pipes and fittings complete with and including required nos size of nuts, bolts and washers complete all as specified and directed by Engineer-in-Charge.

As per item No 223 above but 100 mm bore

As per item No 223 above but 150mm nominal bore

Cutting of existing cast iron pipe in position for taking off connection by inserting CI fittings etc of 80 mm bore bore complete including necessary excavation & earth work and dewatering of residual water all as specified & directed.( CI fittings and joints shall be measured and paid separately under appropriate items)

As per item No 226 above but 100 mm bore

As per item No 226 above but 150 mm bore

M&L run lead joints for spigot and socketed pipes and fittings of 80 mm bore pipes complete all as specified and directed by Engineer-in-Charge.

As per item No 229 above but 100 mm bore

As per item No 229 above but 150 mm bore

M&L Cast iron bends ( any type, radius and angle), Tapers any type, ( straight, bend, increasing , decreasing or double socket etc. ) Tee pieces single branch, 'Y' junction, double branch, cross ( all sockets or socket and spigot collars, caps and plugs complete all as specified and directed by Engineer-in-Charge. ( Jointing and jointing materials measured and paid separately) Upto 150 mm bore.

Taking out sluice valves /NRV of 100 mm bore and removing the same from site complete all as specified and directed by Engineer-in-Charge.

As per item No 233 above but 150 mm bore

Supplying and fixing of sluice valve 100 mm bore , PN 1 heavy duty both ends flanged with steel spindle and check nuts cast iron operating wheel IS-14846 marked with and including nuts,bolts,washers,gaskets etc and dismantling of old unserviceable sluice valve complete all as specified and directed by Engineer-in-Charge.

As per item No 235 above but 150mm bore, PN 1

Drilling/ boring ( horizontally) of following dia by pneumatic tools under existing road ( maximum 10 M in width) Suitable for passing upto 25 mm bore pipe complete all as specified and directed by Engineer-in-Charge.

As per item No 237 above but suitable for passing pipe excd 25 mm and not excd 50 mm bore pipe

As per item No 237 above but upto 100 mm dia bore

S & F ( in repairs) Gun metal gate valve 15 mm bore, Class -1,ISI marked complete with iron wheel head, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.

As per item No 240 above but 20 mm bore

As per item No 240 above but 25 mm bore

As per item No 240 above but 40mm bore

As per item No 240 above but 50mm bore

Cutting existing steel tubing for alterations or additions, screwing existing steel tubing in position ( or lengthening screw on pipe to form connector) and S&F Long screws of the 15 mm bore of pipe complete all as specified and directed by Engineer-in-Charge.

As per item No 245 above but 20 mm bore

As per item No 245 above but 25 mm bore

As per item No 245 above but 40 mm bore

As per item No 245 above but 50 mm bore

Cutting of road ( in hard /dense soil) for laying pipe line or repairs to pipes / lead joints etc. of any size upto 1 metre depth and getting out including forming bottom surface to required level or slope and making good the road as per existing complete all as specified and directed by Engineer-in-Charge.

Drilling and tapping cast iron/ mild steel water mains 15 mm bore ( in position ) for branch connections including supply of GI nipple of medium grade pipe,150mm long complete all as specified and directed by Engineer-in-Charge.

As per item No 251 above but 20 mm bore

As per item No 251 above but 25 mm bore

As per item No 251 above but 40 mm bore

Supply, laying, jointing, testing and commissioning of Mild Steel pipes 15 mm dia Medium grade in any length, conforming to IS:1239(I) with flanged ends including fittings (Bend, Elbow, Tee, etc) and laid in trenches/fixing on wall/floors including painting with two coats of synthetic enamel paint of existing tint/colour complete all as specified and directed by Engineer-in-Charge.

As per item No 255 above but 80 mm dia

As per item No 255 above but 100 mm dia

Supply and fixing in repairs cast iron butterfly valve (wafer type) 80 mm dia lever operated class PN-1.0, S.S-304 Disc, Nitrile/EPDM rubber lining including making new flanged joint with 3mm thick rubber gasket (Packing ring) with necessary bolt, nuts and washer of suitable size complete all as specified and directed by Engineer-in-Charge. Make : Zoloto/Kirloskar

As per item No 258 above but 150 mm dia

M&L for repair of water leakage 80 mm bore in exsting pipe at any location in command hospital area and havlock pump house to command oH tank main pipe line including APS 3 pump house to command hospital OH tank main pipe line with lead joint or gasket joint complete all as specified and directed by Engineer-in-Charge. Note - All Man power, T&P , joint mtrl , excavation , filling etc as required for repair leakge pipe line cost are included in quoted rate by contractor.

As per item No 260 above but 100 mm bore

As per item No 260 above but 150mm nominal bore

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Dismantling fencing wire mesh, any type.

M K Engineers and Contractors

M/s Vatsh Raj and co